Thermoresponsive micropatterned substrates for single cell studies

We describe the design of micropatterned surfaces for single cell studies, based on thermoresponsive polymer brushes. We show that brushes made of poly(N-isopropylacrylamide) grafted at high surface density display excellent protein and cell anti-adhesive properties. Such brushes are readily patterned at the micron scale via deep UV photolithography. A proper choice of the adhesive pattern shapes, combined with the temperature-dependent swelling properties of PNIPAM, allow us to use the polymer brush as a microactuator which induces cell detachment when the temperature is reduced below [Formula: see text]C.     

Antibacterial surfaces based on polymer brushes: investigation on the influence of brush properties on antimicrobial peptide immobilization and antimicrobial activity

Primary amine containing copolymer, poly(N,N-dimethylacrylamide-co-N-(3-aminopropyl)methacrylamide hydrochloride) (poly(DMA-co-APMA)), brushes were synthesized on Ti surface by surface-initiated atom transfer radical polymerization (SI-ATRP) in aqueous conditions. A series of poly(DMA-co-APMA) copolymer brushes on titanium (Ti) surface with different molecular weights, thicknesses, compositions, and graft densities were synthesized by changing the SI-ATRP reaction conditions. Cysteine-functionalized cationic antimicrobial peptide Tet213 (KRWWKWWRRC) was conjugated to the copolymers brushes using a maleimide-thiol addition reaction after initial modification of the grafted chains using 3-maleimidopropionic acid N-hydroxysuccinimide ester. The modified surfaces were characterized by X-ray photoelectron spectroscopy (XPS), water contact angle measurements, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, atomic force microscopy (AFM), and ellipsometry analysis. The conjugation of the Tet213 onto brushes strongly depended on graft density of the brushes at different copolymer brush compositions. The peptide density (peptides/nm(2)) on the surface varied with the initial composition of the copolymer brushes. Higher graft density of the brushes generated high peptide density (pepetide/nm(2)) and lower number of peptides/polymer chain and vice versa. The peptide density and graft density of the chains on surface greatly influenced the antimicrobial activity of peptide grafted polymer brushes against Pseudomonas aeruginosa.     

Role of ionic strength on the relationship of biopolymer conformation,DLVO contributions,and steric interactions to bioadhesion of Pseudomonas putida KT2442

Biopolymers produced extracellularly by Pseudomonas putida KT2442 were examined via atomic force microscopy (AFM) and single molecule force spectroscopy. Surface biopolymers were probed in solutions with added salt concentrations ranging from that of pure water to 1 M KCl. By studying the physicochemical properties of the polymers over this range of salt concentrations, we observed a transition in the steric and electrostatic properties and in the conformation of the biopolymers that were each directly related to bioadhesion. In low salt solutions, the electrophoretic mobility of the bacterium was negative, and large theoretical energy barriers to adhesion were predicted from soft-particle DLVO theory calculations. The brush layer in low salt solution was extended due to electrostatic repulsion, and therefore, steric repulsion was also high (polymers extended 440 nm from surface in pure water). The extended polymer brush layer was "soft", characterized by the slope of the compliance region of the AFM approach curves (-0.014 nN/nm). These properties resulted in low adhesion between biopolymers and the silicon nitride AFM tip. As the salt concentration increased to > or =0.01 M, a transition was observed toward a more rigid and compressed polymer brush layer, and the adhesion forces increased. In 1 M KCl, the polymer brush extended 120 nm from the surface and the rigidity of the outer cell surface was greater (slope of the compliance region = -0.114 nN/nm). A compressed and more rigid polymer layer, as well as a less negative electrophoretic mobility for the bacterium, resulted in higher adhesion forces between the biopolymers and the AFM tip. Scaling theories for polyelectrolyte brushes were also used to explain the behavior of the biopolymer brush layer as a function of salt concentration.     

Electrochemical deposition and surface-initiated RAFT polymerization: protein and cell-resistant PPEGMEMA polymer brushes

This paper introduces a novel and versatile method of grafting protein and cell-resistant poly(poly ethylene glycol methyl ether methacrylate) (PPEGMEMA) brushes on conducting Au surface. The process started with the electrochemical deposition and full characterization of an electro-active chain transfer agent (CTA) on the Au surface. The electrochemical behavior of the CTA was investigated by cyclic voltammetry (CV) while the deposition and stability of the CTA on the surface were confirmed by ellipsometry, contact angle, and X-ray photoelectron spectroscopy (XPS). The capability of the electrodeposited CTA to mediate surface-initiated reversible addition-fragmentation chain transfer (SI-RAFT) polymerization on both the polymethyl methacrylate (PMMA; model polymer) and PPEGMEMA brushes was demonstrated by the increase in thicknesses of the films after polymerization. Contact angles also decreased with the incorporation of the more hydrophilic brushes. Significant changes in the morphologies of the films before and after polymerization were also observed with atomic force microscopy (AFM) analyses. Furthermore, XPS results showed an increase in the O 1s peak intensity relative to C 1s after polymerizations, which confirmed the grafting of polyethyleneglycol (PEG) bearing brushes. The ability of the PPEGMEMA-modified Au surface to resist nonspecific adhesion of proteins and cells was monitored and confirmed by XPS, ellipsometry, contact angle, AFM, and fluorescence imaging. The new method presented has potential application as robust protein and cell-resistant coatings for electrically conducting electrodes and biomedical devices.     

Compatibilization effect of poly(epsilon-caprolactone)-b-poly(ethylene glycol) block copolymers and phase morphology analysis in immiscible poly(lactide)/poly(epsilon-caprolactone) blends

The miscibility and phase behavior of two stereoisomer forms of poly(lactide) (PLA: poly (L-lactide) (PLLA) and poly(DL-lactide) (PDLLA)) blends with poly(epsilon-caprolactone)-b-poly(ethylene glycol) (PCL-b-PEG) and PCL-b-monomethoxy-PEG (PCL-b-MPEG) block copolymers have been investigated by differential scanning calorimetry (DSC). The DSC thermal behavior of both the blend systems revealed that PLA is miscible with the PEG segment phase of PCL-b-(M)PEG but is still immiscible with its PCL segment phase although PCL was block-copolymerized with PEG. On the basis of these results, PCL-b-PEG was added as a compatibilizer to PLA/PCL binary blends. The improvement in mechanical properties of PLA/PCL blends was achieved as anticipated upon the addition of PCL-b-PEG. In addition, atomic force microscopy (AFM) measurements have been performed in order to study the compositional synergism to be observed in mechanical tests. AFM observations of the morphological dependency on blend composition indicate that PLA/PCL blends are immiscible but compatible to some extent and that synergism of compatibilizing may be maximized in the compositional blend ratio before apparent phase separation and coarsening.     

Polyelectrolyte brushes grafted from cellulose nanocrystals using Cu-mediated surface-initiated controlled radical polymerization

Herein we report the synthesis of cellulose nanocrystals (CNCs) grafted with poly(acrylic acid) (PAA) chains of different lengths using Cu-mediated surface initiated-controlled radical polymerization (SI-CRP). First, poly(tert-butylacrylate) (PtBA) brushes were synthesized; then, subsequent acid hydrolysis was used to furnish PAA brushes tethered onto the CNC surfaces. The CNCs were chemically modified to create initiator moieties on the CNC surfaces using chemical vapor deposition (CVD) and continued in solvent phase in DMF. A density of initiator groups of 4.6 bromine ester groups/nm(2) on the CNC surface was reached, suggesting a dense functionalization and a promising starting point for the controlled/living radical polymerization. The SI-CRP of tert-butylacrylate proceeded in a well-controlled manner with the aid of added sacrificial initiator, yielding polymer brushes with polydispersity values typically well below 1.12. We calculated the polymer brush grafting density to almost 0.3 chains/nm(2), corresponding to high grafting densities and dense polymer brush formation on the nanocrystals. Successful rapid acid hydrolysis to remove the tert-butyl groups yielded pH-responsive PAA-polyelectrolyte brushes bound to the CNC surface. Individually dispersed rod-like nanoparticles with brushes of PtBA or PAA were clearly visualized by AFM and TEM imaging.     

Control of nanobiointerfaces generated from well-defined biomimetic polymer brushes for protein and cell manipulations

To better understand protein/material and cell/material interactions at the submolecular level, well-defined polymer brushes consisting of poly(2-methacryloyloxyethyl phosphorylcholine) (PMPC) on silicon wafers were prepared by atom transfer radical polymerization (ATRP). Silicon wafers were treated with 3-(2-bromoisobutyryl)propyl dimethylchlorosilane (BDCS) to form a monolayer that acts as initiators for ATRP. Silicon-supported BDCS monolayers were soaked in a methanol/water mixture solution containing Cu(I)Br, bipyridine, and a sacrificial initiator. After MPC was added to the solution, ATRP was carried out for 18 h. The molecular weight and thickness of the PMPC brush layer on the silicon surface increased with an increase in the polymerization time. The dense polymer brushes were obtained by the "grafting from" system. By selective decomposition of the BDCS monolayer by UV light-irradiation, the PMPC brush region and the sizes were well controlled, resulting in fabricating micropatterns of the PMPC brushes. When the thickness of the PMPC brush layer was greater than 5.5 +/- 1.0 nm (3 h polymerization), serum protein adsorption and fibroblast adhesion were effectively reduced, i.e., proteins and cells could recognize such thin polymer brushes on the surface. In addition, the density of the adherent cells on the patterned PMPC brush surface could be controlled by changing the size of the pattern.     

Osmotic properties of poly(ethylene glycols): quantitative features of brush and bulk scaling laws

From glycosylated cell surfaces to sterically stabilized liposomes, polymers attached to membranes attract biological and therapeutic interest. Can the scaling laws of polymer "brushes" describe the physical properties of these coats? We delineate conditions where the Alexander-de Gennes theory of polymer brushes successfully fits the intermembrane distance versus applied osmotic stress data of Kenworthy et al. for poly(ethylene glycol)-grafted multilamellar liposomes. We establish that the polymer density and size in the brush must be high enough that, in a bulk solution of equivalent monomer density, the polymer osmotic pressure is independent of polymer molecular weight (the des Cloizeaux semidilute regime of bulk polymer solutions). The condition that attached polymers behave as semidilute bulk solutions offers a rigorous criterion for brush scaling-law behavior. There is a deep connection between the behaviors of semidilute polymer solutions in bulk and polymers grafted to a surface at a density such that neighbors pack to form a uniform brush. In this regime, two-parameter unconstrained fits of the Alexander-de Gennes brush scaling laws to the Kenworthy et al. data yield effective monomer lengths of 3.3-3.6 A, which agree with structural predictions. The fitted distances between grafting sites are larger than expected from the nominal mole fraction of poly(ethylene glycol)-lipids; the chains apparently saturate the surface. Osmotic stress measurements can be used to estimate the actual densities of membrane-grafted polymers.     

Poly(HEMA) brushes emerging as a new platform for direct detection of food pathogen in milk samples

Surface plasmon resonance (SPR) biosensors capable of in real time detection of Cronobacter at concentrations down to 10? cells mL?1 in samples of consumer fresh-whole fat milk, powder whole-fat milk preparation, and powder infant formulation were developed for the first time. Antibodies against Cronobacter were covalently attached onto polymer brushes of poly(2-hydroxyethyl methacrylate) (poly(HEMA)) grafted from the SPR chip surface. The lowest detection limit, 10? cells mL?1, was achieved in phosphate buffered saline (pH 7.4) with sensors prepared by covalent immobilization of the same antibodies onto a self assembled monolayer (SAM) of hexa(ethylene glycol) undecanethiol (EG?). However, when the EG? based sensors were challenged with milk samples the non-specific response due to the deposition of non-targeted compounds from the milk samples was much higher than the specific response to Cronobacter hampering the detection in milk. Similar interfering fouling was observed on antifouling polymer brushes of hydroxy-capped oligoethylene glycol methacrylate and even a 10 times higher fouling was observed on the widely used SAM of mixed hydroxy- and carboxy-terminated alkanethiols. Only poly(HEMA) brushes totally suppressed the fouling from milk samples. The robust well-controlled surface initiated atom transfer radical polymerization of HEMA allowed the preparation of highly dense brushes with a minimal thickness so that the capture of antigens by the antibodies immobilized on the brush layer could take place close to the gold SPR surface to provide a stronger optical response while the fouling was still suppressed. A minimum thickness of 19 nm of poly(HEMA) brush layer was necessary to suppress completely non-specific sensor response to fouling from milk.     

Stability and nonfouling properties of poly(poly(ethylene glycol) methacrylate) brushes under cell culture conditions

This paper investigates the stability and nonfouling properties of poly(poly(ethylene glycol) methacrylate) (PPEGMA) brushes prepared by surface-initiated atom transfer radical polymerization from SiO(x) substrates modified with a trimethoxysilane-based ATRP initiator. At high chain densities, PPEGMA brushes were found to detach rapidly from glass or silicon substrates. Detachment of the PPEGMA brushes could be monitored with contact angle measurements, which indicated a decrease in the receding water contact angle upon detachment. Detachment of the PPEGMA brushes also resulted in an increase in nonspecific protein adsorption. The stability, and as a consequence the long-term nonfouling properties, of the PPEGMA brushes could be improved by tailoring the brush density and, to a lesser extent, the molecular weight of the polymer chains. By appropriate decrease of the grafting density, the stability of the brushes in cell culture medium could be improved from less than 1 to more than 7 days, without compromising the nonfouling properties.     

Evaluation of brushes for removal of fouling from fouling-release surfaces, using a hydraulic cleaning device

A portable hydraulic device has been developed for use in optimizing the design of brushes and cleaning units that may be employed to maintain fouling-release coatings. Laboratory tests showed that characteristics of experimental cleaning brushes, including bristle stiffness, density, and angle, significantly affected the shear and normal forces imparted to the surface and thus, to any encrusting organisms. The standoff distance between the cleaning unit and the surface also influenced the forces generated. The rate of rotation of the brush, however, had little effect on force. The hydraulic device, with its experimental brushes, can also be used to evaluate the cleanability of fouling-release surfaces in situ, or to assess wear of the coating system due to cleaning.     

Micropatterning of polymer brushes: grafting from dewetting polymer films for biological applications

In this novel platform, a micropatterned polymer brush was obtained by grafting poly(poly(ethylene glycol) methyl ether methacrylate) (poly(PEGMA)) from a thin macroinitiator film using atom transfer radical polymerization (ATRP). A pattern of holes was formed in the macroinitiator film by taking advantage of its spontaneous dewetting above the glass transition temperature from a bottom polystyrene film, driven by unfavorable intermolecular forces. Patterning by dewetting can be achieved at length-scales from a few hundred nanometers to several tens of micrometers, by simply thermally annealing the bilayer above the glass transition temperature of the polymer. This approach is substrate-independent, as polymer films can be cast onto surfaces of different size, shape, or material. As a demonstration of its potential, proteins, and individual cells were attached on targeted bioadhesive polystyrene areas of the micropatterns within poly(PEGMA) protein-repellent brushes. We anticipate this approach will be suitable for the patterning of brushes, especially for biomedical applications such as in the study of single cells and of cell cocultures.     

Evaluation of Brushes for Removal of Fouling from Fouling-release Surfaces,Using a Hydraulic Cleaning Device

A portable hydraulic device has been developed for use in optimizing the design of brushes and cleaning units that may be employed to maintain fouling-release coatings. Laboratory tests showed that characteristics of experimental cleaning brushes, including bristle stiffness, density, and angle, significantly affected the shear and normal forces imparted to the surface and thus, to any encrusting organisms. The standoff distance between the cleaning unit and the surface also influenced the forces generated. The rate of rotation of the brush, however, had little effect on force. The hydraulic device, with its experimental brushes, can also be used to evaluate the cleanability of fouling-release surfaces in situ, or to assess wear of the coating system due to cleaning.     

Surface interaction forces of cellulose nanocrystals grafted with thermoresponsive polymer brushes

The colloidal stability and thermoresponsive behavior of poly(N-isopropylacrylamide) brushes grafted from cellulose nanocrystals (CNCs) of varying graft densities and molecular weights was investigated. Indication of the grafted polymer brushes was obtained after AFM imaging of CNCs adsorbed on silica. Also, aggregation of the nanoparticles carrying grafts of high degree of polymerization was observed. The responsiveness of grafted CNCs in aqueous dispersions and as an ultrathin film was evaluated by using light scattering, viscosimetry, and colloidal probe microscopy (CPM). Light transmittance measurements showed temperature-dependent aggregation originating from the different graft densities and molecular weights. The lower critical solution temperature (LCST) of grafted poly(NiPAAm) brushes was found to decrease with the ionic strength, as is the case for free poly(NiPAAm) in aqueous solution. Thermal responsive behavior of grafted CNCs in aqueous dispersions was observed by a sharp increase in dispersion viscosity as the temperature approached the LCST. CPM in liquid media for asymmetric systems consisting of ultrathin films of CNCs and a colloidal silica probe showed the distinctive effects of the grafted polymer brushes on interaction and adhesive forces. The origin of such forces was found to be mainly electrostatic and steric in the case of bare and grafted CNCs, respectively. A decrease in the onset of attractive and adhesion forces of grafted CNCs films were observed with the ionic strength of the aqueous solution. The decreased mobility of polymer brushes upon partial collapse and decreased availability of hydrogen bonding sites with higher electrolyte concentration were hypothesized as the main reasons for the less prominent polymer bridging between interacting surfaces.     

Patterned Immobilization of Antibodies within Roll-to-Roll Hot Embossed Polymeric Microfluidic Channels

This paper describes a method for the patterned immobilization of capture antibodies into a microfluidic platform fabricated by roll-to-roll (R2R) hot embossing on poly (methyl methacrylate) (PMMA). Covalent attachment of antibodies was achieved by two sequential inkjet printing steps. First, a polyethyleneimine (PEI) layer was deposited onto oxygen plasma activated PMMA foil and further cross-linked with glutaraldehyde (GA) to provide an amine-reactive aldehyde surface (PEI-GA). This step was followed by a second deposition of antibody by overprinting on the PEI-GA patterned PMMA foil. The PEI polymer ink was first formulated to ensure stable drop formation in inkjet printing and the printed films were characterized using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Anti-CRP antibody was patterned on PMMA foil by the developed method and bonded permanently with R2R hot embossed PMMA microchannels by solvent bonding lamination. The functionality of the immobilized antibody inside the microfluidic channel was evaluated by fluorescence-based sandwich immunoassay for detection of C-reactive protein (CRP). The antibody-antigen assay exhibited a good level of linearity over the range of 10 ng/ml to 500 ng/ml (R² = 0.991) with a calculated detection limit of 5.2 ng/ml. The developed patterning method is straightforward, rapid and provides a versatile approach for creating multiple protein patterns in a single microfluidic channel for multiplexed immunoassays.     

Adsorption characteristics of P(3HB) depolymerase as evaluated by surface plasmon resonance and atomic force microscopy

Molecular recognition of poly[(R)-3-hydroxybutyrate] (P(3HB)) depolymerase from Ralstonia pickettii T1 to the surfaces of biodegradable aliphatic polyesters such as P(3HB) and poly(L-lactic acid) (PLLA) was examined from the viewpoints of kinetics and dynamics. To determine the kinetic parameters on the interaction between the substrate-binding domain (SBD) of P(3HB) depolymerase and various polymer substrates with different chemical structures, surface plasmon resonance (SPR) measurements were performed. On the other hand, using an atomic force microscopic (AFM) cantilever tip functionalized with the SBD of P(3HB) depolymerase, the mechanical parameters such as unbinding force to the polymer surfaces were measured. Both the SPR and AFM measurements showed that the SBD has a high affinity to P(3HB) and PLLA. From the results of kinetics and dynamics, the energy potential landscape of SBD-polymer interaction was disclosed on the basis of a phenomenological model, and the mechanism of the interaction was discussed.     

Effect of water on the surface molecular mobility of poly(lactide) thin films: an atomic force microscopy study

Physical properties associated with molecular mobility on the surface of thin films with 300 nm thickness for poly(lactide)s (PLAs) were studied under vacuum conditions as well as under aqueous conditions by using friction force mode atomic force microscopy (AFM). Two types of PLAs were applied for the experimental samples as uncrystallizable PLA (uc-PLA) and crystallizable PLA (c-PLA). The friction force on the surface of thin films was measured as a function of temperature to assess the surface molecular mobility both under vacuum and under aqueous conditions. A lower glass-transition temperature of the uc-PLA surface in water was detected than that under vacuum conditions. In the case of the c-PLA thin film, change in friction force was detected at a lower temperature under aqueous conditions than in vacuo. A morphological change was observed in the c-PLA thin film during heating process from room temperature to 100 degrees C by temperature-controlled AFM. The surface of the c-PLA thin film became rough due to the cold crystallization, and the crystallization of c-PLA molecules in water took place at a lower temperature than in vacuo. These friction force measurements and AFM observations suggest that molecular motion on the surface of the both uc- and c-PLA thin films is enhanced in the presence of water molecules. In addition, in situ AFM observation of the enzymatic degradation process for the c-PLA thin film crystallized at 160 degrees C was carried out in buffer solution containing proteinase K at room temperature. The amorphous region around the hexagonal crystal was eroded within 15 min. It has been suggested that the adsorption of water molecules on the PLA film surface enhances the surface molecular mobility of the glassy amorphous region of PLA and induces the enzymatic hydrolysis by proteinase K.     

Functional polymer brushes via surface-initiated atom transfer radical graft polymerization for combating marine biofouling

Dense and uniform polymer brush coatings were developed to combat marine biofouling. Nonionic hydrophilic, nonionic hydrophobic, cationic, anionic and zwitterionic polymer brush coatings were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP) of 2-hydroxyethyl methacrylate, 2,3,4,5,6-pentafluorostyrene, 2-(methacryloyloxy)ethyl trimethylammonium chloride, 4-styrenesulfonic acid sodium and N,N'-dimethyl-(methylmethacryloyl ethyl) ammonium propanesulfonate, respectively. The functionalized surfaces had different efficacies in preventing adsorption of bovine serum albumin (BSA), adhesion of the Gram-negative bacterium Pseudomonas sp. NCIMB 2021 and the Gram-positive Staphylococcus aureus, and settlement of cyprids of the barnacle Amphibalanus amphitrite (=Balanus amphitrite). The nonionic hydrophilic, anionic and zwitterionic polymer brushes resisted BSA adsorption during a 2?h exposure period. The nonionic hydrophilic, cationic and zwitterionic brushes exhibited resistance to bacterial fouling (24?h exposure) and cyprid settlement (24 and 48?h incubation). The hydrophobic brushes moderately reduced protein adsorption, and bacteria and cyprid settlement. The anionic brushes were least effective in preventing attachment of bacteria and barnacle cyprids. Thus, the best approach to combat biofouling involves a combination of nonionic hydrophilic and zwitterionic polymer brush coatings on material surfaces.     

Patterned biofunctional poly(acrylic acid) brushes on silicon surfaces

Protein patterning was carried out using a simple procedure based on photolithography wherein the protein was not subjected to UV irradiation and high temperatures or contacted with denaturing solvents or strongly acidic or basic solutions. Self-assembled monolayers of poly(ethylene glycol) (PEG) on silicon surfaces were exposed to oxygen plasma through a patterned photoresist. The etched regions were back-filled with an initiator for surface-initiated atom transfer radical polymerization (ATRP). ATRP of sodium acrylate was readily achieved at room temperature in an aqueous medium. Protonation of the polymer resulted in patterned poly(acrylic acid) (PAA) brushes. A variety of biomolecules containing amino groups could be covalently tethered to the dense carboxyl groups of the brush, under relatively mild conditions. The PEG regions surrounding the PAA brush greatly reduced nonspecific adsorption. Avidin was covalently attached to PAA brushes, and biotin-tagged proteins could be immobilized through avidin-biotin interaction. Such an immobilization method, which is based on specific interactions, is expected to better retain protein functionality than direct covalent binding. Using biotin-tagged bovine serum albumin (BSA) as a model, a simple strategy was developed for immobilization of small biological molecules using BSA as linkages, while BSA can simultaneously block nonspecific interactions.