Cu3P Binary Phosphide: Synthesis via a Wet Mechanochemical Method and Electrochemical Behavior as Negative Electrode Material for Lithium‐Ion Batteries

Mechanochemical synthesis of Cu₃P in the presence of n‐dodecane results in a material with a secondary particle size distribution of 10 μm, secondary particles which consist of homogeneously agglomerated 20 nm primary particles. The electrochemical performance of Cu₃P with lithium is influenced by the reaction depth, in other words by the lower potential cut‐off. During the electrochemical reaction, the displacement of copper by lithium from the Cu₃P structure until the formation of Li₃P and Cu deteriorates the capacity retention. Improved performance was obtained when the charge potential was limited to 0.50 V (vs. Li/Li⁺) and the formation of the Li_xCu_3‐xP phase (0 ≤ × ≤ 2). In this case, when the potential is limited to 0.5 V, the capacity is stable for more than 50 cycles. Acceptable electrochemical performances in Li‐ion cells within the voltage range 0.50–2.0 V (vs. Li/Li⁺) were shown when Cu₃P was used as an anode and Li_1.2(Ni_0.13Mn_0.54Co_0.13)O₂ and LiNi_0.5Mn_1.5O₄ as positive electrode materials.     

Luminescence in Li2BaP2O7

The photo‐, thermo‐ and optically stimulated luminescence in Li₂BaP₂O₇ activated with Eu²⁺/Cu⁺ are reported. Strong thermoluminescence, which is about two times greater than LiF‐TLD 100 was observed in the Eu²⁺‐activated sample. It also exhibited optically stimulated luminescence sensitivity of ~20% that of commercial Al₂O₃:C phosphor. Copyright © 2014 John Wiley & Sons, Ltd.     

Luminescence characterization of Dy and Eu doped Na6Mg(SO4)4 phosphors

A series of single‐phase phosphors based on Na₆Mg(SO₄)₄ (Z_eff = 11.70) doped with Dy and Eu was prepared by the wet chemical method. The photoluminescence (PL) and thermoluminescence (TL) properties of Dy³⁺‐ and Eu³⁺‐activated Na₆Mg(SO₄)₄ phosphors were investigated. The characteristic emissions of Dy³⁺ and Eu³⁺ were observed in the Na₆Mg(SO₄)₄ host. The TL glow curve of the Na₆Mg(SO₄)₄:Dy phosphor consisted of a prominent peak at 234°C and a very small hump at 158°C. The TL sensitivity of the Na₆Mg(SO₄)₄:Dy phosphor was found to be four times less than the commercialized CaSO₄:Dy phosphor. The TL dose–response of the Na₆Mg(SO₄)₄:Dy phosphor was studied from a dose range of 5–10 kGy and the linear dose–response was observed up to 1 kGy which is good for a microcrystalline phosphor. Trapping parameters for both the samples were calculated using the Initial Rise and Chen's peak shape methods.     

Preliminary results on the photoluminescence and optically stimulated luminescence in Cu‐doped and Ag‐doped ZnB2X4 (B = Li,Na, K: X = Cl,Br) compounds

Photoluminescence, and optically stimulated luminescence in ZnB₂X₄ (B; Li,Na,K: X; Cl,Br) compounds doped with Cu⁺ or Ag⁺ were studied. Double humped emission bands attributable to the activators were observed in all the samples. The observed photoluminescence of Cu⁺ and Ag⁺ could be identified with 3d⁹4s¹?3d¹⁰ and 4d⁹5s¹?5d¹⁰ transitions respectively. The longer wavelength band (400–500 nm range) could be attributed to the Cu⁺ or Ag⁺ ion replacing alkali ion at the octahedral alkali site whereas short wavelength band (340–400 nm range) is attributed to a Cu or Ag ion at tetrahedral zinc site. The short wavelength band was found to be intense compared with long wavelength and gave an indication that most of the Cu or Ag ions prefered a tetrahedral Zn site compared with the octahedral alkali site. All the samples exhibit optically stimulated luminescence (OSL). The sensitivity was found to be lattice dependent. The lowest sensitivity of about 1% compared with Al₂O₃:C was observed in lithium lattices whereas highest the sensitivity of about 290% was observed in the case of Cu‐doped ZnNa₂Br₄.     

A membrane-free baffled microbial fuel cell for cathodic reduction of Cu(II) with electricity generation

A membrane-free baffled microbial fuel cell (MFC) was developed to treat synthetic Cu(II) sulfate containing wastewater in cathode chamber and synthetic glucose-containing wastewater fed to anode chamber. Maximum power density of 314 mW/m³ with columbic efficiency of 5.3% was obtained using initial Cu²⁺ concentration of 6400 mg/L. Higher current density favored the cathodic reduction of Cu²⁺, and removal of Cu²⁺ by 70% was observed within 144 h using initial concentration of 500 mg/L. Powder X-ray diffraction (XRD) analysis indicated that the Cu²⁺ was reduced to Cu₂O or Cu₂O plus Cu which deposited on the cathode, and the deficient cathodic reducibility resulted in the formation of Cu₄(OH)₆SO₄ at high initial Cu²⁺ concentration (500-6400 mg/L). This study suggested a novel low-cost approach to remove and recover Cu(II) from Cu²⁺-containing wastewater using MFC-type reactor.     

A novel red emitting phosphor LiBaB9O15:Sm2+/Sm3+, li+ with broad excitation band for white LEDs

A novel tunable red emitting phosphor LiBaB₉O₁₅:Sm²⁺/Sm³⁺, Li⁺ with broad excitation band was synthesized by a high temperature solid‐state method. Luminescence properties were investigated in detail by luminescence, X‐ray photoelectron spectroscopy (XPS) spectra and CIE chromaticity coordinates. XPS data confirmed that there were Sm³⁺ in LiBaB₉O₁₅:Sm³⁺ and Sm²⁺/Sm³⁺ in LiBaB₉O₁₅:Sm²⁺/Sm³⁺, respectively. Spectral property of LiBaB₉O₁₅:Sm³⁺, LiBaB₉O₁₅:Sm³⁺/Sm²⁺ and LiBaB₉O₁₅:Sm²⁺, Li⁺ presented that the excitation band of Sm³⁺ widened and the excitation band of Sm²⁺ ranged from 350 to 450 nm. And the red light color is tunable with changing Li⁺ concentration. The results indicated that LiBaB₉O₁₅:Sm²⁺/Sm³⁺, Li⁺ may be promising red phosphor for white light emitting diodes.     

Tunable white light emission from single‐phased Li2SrSiO4:Dy3+ phosphors by co‐doping with Eu3+

A series of single‐phase full‐color emitting Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors were synthesized by solid‐state reaction and characterized by X‐ray diffraction and photoluminescence analyses. The samples showed emission peaks at 488 nm (blue), 572 nm (yellow), 592 nm (orange) and 617 nm (red) under 393 nm excitation. The photoluminescence excitation spectra, comprising the Eu–O charge transfer band and 4f–4f transition bands of Dy³⁺ and Eu³⁺, range from 200 to 500 nm. The Commission Internationale de I'Eclairage chromaticity coordinates for Li₂Sr_0.98−xSiO₄:0.02Dy³⁺,xEu³⁺ phosphors were simulated. By manipulating Eu³⁺ and Dy³⁺ concentrations, the color points of Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ were tuned from the greenish‐white region to white light and eventually to reddish‐white region, demonstrating that a tunable white light can be obtained by Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors. Li₂Sr_0.98−xSiO₄:0.02Dy³⁺, xEu³⁺ can serve as a white‐light‐emitting phosphor for phosphor‐converted light‐emitting diode. Copyright © 2014 John Wiley & Sons, Ltd.     

Photoluminescence and thermoluminescence of K2Mg(SO4)2:Eu and evaluation of its kinetic parameters

The K₂Mg(SO₄)₂:Eu phosphor, synthesized by a solid‐state diffusion method, was studied for its photoluminescence (PL) and thermoluminescence (TL) characteristics. The X‐ray diffraction (XRD) pattern of the material was matched with the standard JCPDF No. 36–1499. For PL characteristics, K₂Mg(SO₄)₂:Eu²⁺ showed an emission peak at 474 nm when excited at 340 nm, while it showed Eu³⁺ emission at 580 nm, and 594 nm splitting at 613 nm and 618 nm for an excitation of 396 nm wavelength due to radiative transitions from ⁵D₀ to ⁷F_j (j = 0, 1, 2, 3). The Commission International de I′ Eclairage (CIE) chromaticity coordinates were also calculated for the K₂Mg(SO₄)₂:Eu phosphor, and were close to the NTSC standard values. For the TL study, the prepared sample was irradiated using a ⁶⁰Co source of γ‐irradiation at the dose rate of 0.322 kGy/h for 2 min. The formation of traps in K₂Mg (SO₄)₂:Eu and the effects of γ‐radiation dose on the glow curve are discussed. Well defined broad glow peaks were obtained at 186°C. With increasing γ‐ray dose, the sample showed linearity in intensity. The presence of a single glow peak indicated that there was only one set of traps being activated within the particular temperature range. The presented phosphors were also studied for their fading, reusability and trapping parameters. There was just 2% fading during a period of 30 days, indicating no serious fading problem. Kinetic parameters were calculated using the initial rise method and Chen's half‐width method. Activation energy and frequency factor were found to be 0.77 eV and 1.41 × 10⁶ sec^?1.     

Optical properties of CaAl(SO4)2Br:RE (RE = Dy,Eu, Ce) novel phosphors

A new phosphor CaAl(SO₄)₂Br doped with Dy, Ce and Eu is reported. Rare earth (Dy, Eu and Ce)‐doped polycrystalline CaAl(SO₄)₂Br phosphors were prepared using a wet chemical reaction method and studied for X‐ray diffraction and photoluminescence (PL) characteristics. Dy³⁺ emission in the CaAl(SO₄)₂Br lattice was observed at 484 and 574 nm in the blue and yellow regions of the spectrum, which are assigned to ⁴ F_9/2 → ⁶H_15/2 and ⁴ F_9/2 → ⁶H_13/2 transitions of the Dy³⁺ ion, respectively. While the PL emission spectra of CaAl(SO₄)₂Br:Ce phosphor showed Ce³⁺ emission at 347 nm due to 5d → 4f transition of the Ce³⁺ ion. In a CaAl(SO₄)₂Br:Eu lattice, Eu³⁺ emissions were observed at 593 and 617 nm, coming from the ⁵D₀ → ⁷ F₁ and ⁵D₀ → ⁷ F₂ electron transitions, respectively. The PL study showed that the intensity of electric dipole transition at 617 nm dominates over that of magnetic dipole transition at 590 nm. The maximum PL intensity was obtained for a 1 mol% concentration of Eu³⁺ in CaAl(SO₄)₂Br host lattice. The results showed that the material may be a promising candidate as a blue‐, yellow‐ and red‐emitting phosphor. Copyright © 2013 John Wiley & Sons, Ltd.     

The effects of charge compensation on photoluminescence properties of a new green‐emitting ZnB2O4:Tb3+ phosphor

Charge compensation is an effective way to eliminate charge defects and improve the luminescent intensity of phosphors. In this paper, a new green‐emitting phosphor ZnB₂O₄:Tb³⁺ was prepared by solid‐state reaction at 750°C. The effects of Tb³⁺ doping content and charge compensators (Li⁺, Na⁺ or K⁺) on photoluminescence properties of ZnB₂O₄:Tb³⁺ were investigated. X‐ray powder diffraction analysis confirms the sample has cubic structure of ZnB₂O₄. The excitation and emission spectra indicate that this phosphor can be excited by near ultraviolet light at 378 nm, and exhibits bright green emission with the highest peak at 544 nm corresponding to the ⁵D₄→⁷F₅ transition of Tb³⁺. The critical quenching concentration of Tb³⁺ in ZnB₂O₄ host is 8 mol%. The results of charge compensation show that the emission intensity can be improved by Na⁺ and K⁺. Specifically, K⁺ is the optimal one for ZnB₂O₄:Tb³⁺. Copyright © 2014 John Wiley & Sons, Ltd.     

Luminescence characteristics of Na3Ca2(SO4)3F: Ce3+ fluoride material

A new Na₃Ca₂(SO₄)₃F: Ce³⁺ phosphor synthesized by a solid state diffusion method is reported. The photoluminescence study showed a single high intensity emission peak at 307 nm wavelength when excited by UV light of wavelength 278 nm. An unresolved peak of comparatively less intensity was also observed at 357 nm along with the main peak. The characteristic emission of dopant Ce in Na₃Ca₂(SO₄)₃F phosphor clearly indicated that it resides in the host lattice in trivalent form. The emission peak can be attributed to 5d → 4f transition of rare earth Ce³⁺. The prepared sample is also characterized for its thermoluminescence properties. The TL glow curve of prepared sample showed a single broad peak at 147°C. The trapping parameters are also evaluated by Chen's method. The values of trap depth (E) and frequency factor (s) were found to be 0.64 ± 0.002 eV and 1.43 × 10⁷ s^–1 respectively. The study of PL and TL along with evaluation of trapping parameters has been undertaken and discussed for the first time. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of ZnSe and ZnSe:Cu quantum dots by a room temperature photochemical (UV‐assisted) approach using Na2SeO3 as Se source and investigating optical properties

In this study, ZnSe and ZnSe:Cu quantum dots (QDs) were synthesized using Na₂SeO₃ as the Se source by a rapid and room temperature photochemical (UV‐assisted) approach. Thioglycolic acid (TGA) was employed as the capping agent and UV illumination activated the chemical reactions. Synthesized QDs were successfully characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), photoluminescence (PL) and UV–visible (UV–vis) spectroscopy, Fourier transform‐infrared (FT‐IR), and energy dispersive X‐ray spectroscopy (EDX). XRD analysis demonstrated the cubic zinc blend phase QDs. TEM images indicated that round‐shaped particles were formed, most of which had a diameter of about 4 nm. The band gap of the ZnSe QDs was higher than that for ZnSe in bulk. PL spectra indicated an emission with three peaks related to the excitonic, surface trap states and deep level (DL) states. The band gap and QD emission were tunable only by UV illumination time during synthesis. ZnSe:Cu showed green emission due to transition of electrons from the Conduction band (CB) or surface trap states to the ²T₂ acceptor levels of Cu²⁺. The emission was increased by increasing the Cu²⁺ ion concentration, such that the optimal value of PL intensity was obtained for the nominal mole ratio of Cu:Zn 1.5%.     

Synthesis and properties of crown ether isocyanide silver(I) derivatives: X-ray structure of a self-assembled 22-membered diargentacycle

The crown ether isocyanide CNR (R = benzo-15-crown-5) reacts with silver(I) salts in the appropriate molar ratio to give [Ag(CNR)_n]X (n = 1, 2; X = CF₃SO₃, BF₄). X-ray diffraction studies of [Ag(CF₃SO₃)(CNR)] show the molecules associated in a dinuclear manner with an antiparallel orientation. The silver centers are tetracoordinated to the isocyanide and to three oxygens, one from the triflate anion and two from the second crown ether in the dimer. The molecular structure displays five cycles: the two 15-crown ether rings, two five-membered argentacycles and a 22-membered diargentacycle. The crown ether in these complexes is able to detect alkaline cations from M(CF₃SO₃) (M = Li, Na, K) by NMR in d₆-acetone solutions, and to distinguish Li⁺-Na⁺ from K⁺.     

Extracellular synthesis of cuprous selenide nanospheres by a biological‐chemical coupling reduction process in an anaerobic microbial system

Biosynthesis of metal nanoparticles represents a clean, eco‐friendly and sustainable “green chemistry” engineering. Lately, a number of metal selenides were successfully synthesized by biological methods. Here, cuprous selenide (Cu₂Se) nanospheres were prepared under mild conditions by a novel biological‐chemical coupling reduction process. The simple process takes place between EDTA‐Cu and Na₂SeO₃ in presence of an alkaline solution containing NaBH₄ and a selenite‐reducing bacteria, Pantoea agglomerans. It is noteworthy that the isolated Pantoea agglomerans and Cu⁺ ions, where the latter are obtained from reducing Cu²⁺ ions by NaBH₄, play a key role, and Cu⁺ ions not only can promote the generation of Se^2? ions as a catalyst, but also can react with Se^2? ions to form Cu₂Se. XRD pattern, SEM, and TEM images indicated that Cu₂Se nanoparticles were tetragonal crystal structure and the nanospheres diameter were about 100 nm. EDX, UV–vis, and FTIR spectra show that the biosynthesized Cu₂Se nanospheres are wrapped by protein and have a better stability. This work first proposes a new biosynthesis mechanism, and has important reference value for biological preparation of metal selenide nanomaterials. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:1264–1270, 2016     

Novel optical properties of Ca12Al10.6Si3.4O32Cl5.4:Ce3+,Li+ phosphor for solid‐state lighting

This article reports a novel blue emission in a series of Ca₁₂Al_10.6Si_3.4O₃₂Cl_5.4:Ce³⁺ phosphor under excitation in the near‐UV wavelength range. This phosphor was prepared using the combustion method. Here, the Ce³⁺ emission band is observed over a broad range of 380–550 nm, under 365 nm excitation, and is due to 5d–4f transition. The effect of a Li⁺ charge compensator on the emission properties of the phosphor was also investigated for the first time. X‐Ray diffraction confirmed the phase purity of the synthesized phosphor. The surface morphology and elemental composition of the phosphor were studied using scanning electron microscopy and energy‐dispersive X‐ray spectroscopy. Copyright © 2016 John Wiley & Sons, Ltd.     

Sr2ZnWO6:Eu3+,Bi3+,Li+: a potential white‐emitting phosphor for near‐ultraviolet white light‐emitting diodes

A series of Sr₂ZnWO₆ phosphors co‐doped with Eu³⁺, Bi³⁺ and Li⁺ were prepared using the Pechini method. The samples were tested using X‐ray diffraction and luminescence spectroscopy. The results show that the samples can be effectively excited by near‐ultraviolet (UV) and UV light. The introduction of Bi³⁺ and Li⁺ significantly enhances the fluorescence emission of Sr₂ZnWO₆:Eu³⁺ and changes the light emitted by the phosphors from bluish‐green to white. When excited at 371 nm, Sr_2–x–zZn_1–yWO₆:xEu³⁺,yBi³⁺,zLi⁺ (x = 0.05, y = 0.05, z = 0.05, 0.1 and 0.15) samples emit high‐performance white light. Intense red–orange emission is also observed when excited by UV light. The obtained phosphor is a potential white‐emitting phosphor that could meet the needs of excitation sources with near‐UV chips. In addition, this phosphor might have promising application as a red–orange emitting phosphor for white light‐emitting diodes based on UV light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Oligomerization of the Cu(II) and Ni(II) tetraazaannulene complexes: A pulse radiolysis study of the associated reaction mechanism

The oligomerization of [Cu^II(H_x(tmdnTAA))]^x+ (x = 0, 1, 2 and (tmdnTAA))²⁻ is 2,4,9,11-tetramethyl-dinaphto[14]-2,4,6,9,11,13-hexaeneN₄) was initiated in homogeneous solution via the reaction of this Cu(II) complex with pulse radiolytically generated radicals. The reaction produces Cu(III) intermediates which are rapidly converted to Cu(II) ligand-radical species. In contrast to the mechanism proposed for the electrochemical oligomerization, where the local concentration of radicals is probably high, the reaction kinetics in homogeneous solution is propagated by a process where the Cu(II) ligand-radical precursors react with [Cu^II(H_x(tmdnTAA))]^x+.     

A promising RVO4:Eu3+,Li+@SiO2 (R = Gd,Y and Gd/Y) red‐emitting phosphor with improved luminescence (cd/m2) and colour purity for optical display applications

Red emission intensity was optimized in three stages, by investigating the effects of: (i) host composition (Gd, Y and Gd/Y), (ii) codoping Li⁺ as a sensitizer and, finally, (iii) with a SiO₂ shell coating as a protecting layer. Lanthanide vanadate powder phosphors were synthesized using a modified colloidal precipitation technique. The effects of SiO₂ coating on phosphor particles were characterized using scanning electron microscopy (SEM)‐EDAX, transmission electron microscopy (TEM), Fourier transform infrared (FTIR) and photoluminescence (PL) measurements. An improvement in the PL intensity on Li codoping was due to improved crystallinity, which led to higher oscillating strengths for the optical transitions, and also a lowering of the inversion symmetry of Eu³⁺ ions. Red emission intensity due to ⁵D₀ → ⁵D₂ transition of the phosphor Y_0.94VO₄:Eu³⁺_0.05,Li⁺_0.01 was enhanced by 22.28% compared with Y_0.95VO₄:Eu³⁺_0.05, and was further improved by 58.73% with SiO₂ coating. The luminescence intensity (I) and colour coordinates (x, y) of the optimized phosphor Y_0.94VO₄:Eu³⁺_0.05,Li⁺_0.01@SiO₂, where I = 13.07 cd/m² and (x = 0.6721, y = 0.3240), were compared with values for a commercial red phosphor (Y₂O₂S:Eu³⁺), where I = 27 cd/m² and (x = 0.6522, y = 0.3437). The measured colour coordinates are superior to those of the commercial red phosphor, and moreover, match well with standard NTSC values (x = 0.67, y = 0.33). Copyright © 2015 John Wiley & Sons, Ltd.     

A study of Li+-selective permeation through lipid bilayer membranes mediated by a new ionophore (AS701)

The neutral, noncyclic, imide and ether containing ionophore AS701, has been developed as Li⁺-selective molecule, to be used potentially as an aid in the Li⁺-therapy of manic-depressive illness. The present report is a characterization of this molecule in neutral lipid bilayer membranes. This ionophore was found to the bilayers Li⁺-selective, acting as a selective carrier of monovalent cations. In addition, this molecule was found to be capable of acting as a selective carrier of monovalent anions. For both types of ions, the rate-limitting step in the process of permeation was found to be the diffusion of the carrier-ion complex through the membrane. The membrane-permeating species were found to be 2 : 1 carrier-ion complexes, carrying either a monovalent cation or a monovalent anion. The selectivity sequences among the ions studied being: Li⁺(1) > ClO₄^?(0.7) > Na⁺(0.07) > K⁺(0.016) > Rb⁺(0.0095) > Cs⁺(0.0083) > Cl^?(0.001). Mg²⁺ and SO₄^2? were found to be impermeant (under present experimental conditions). This sequence shows that the AS701 molecule has low selectivity for ions present in biological media, among those studied (i.e. Na⁺, K⁺, Mg²⁺, Cl^2? and SO₄^2?). This indicates that these ions will not interfere in the Li⁺ permeability induced by this carrier in vivo, and that the carrier will not interfere in the normal transport processes of these ions.     

Paramelaconite‐Enriched Copper‐Based Material as an Efficient and Robust Catalyst for Electrochemical Carbon Dioxide Reduction

A copper‐oxide‐based catalyst enriched with paramelaconite (Cu₄O₃) is presented and investigated as an electrocatalyst for facilitating electroreduction of CO₂ to ethylene and other hydrocarbons. Cu₄O₃ is a member of the copper‐oxide family and possesses an intriguing mixed‐valance nature, incorporating an equal number of Cu⁺ and Cu²⁺ ions in its crystal structure. The material is synthesized using a solvothermal synthesis route and its structure is confirmed via powder X‐ray diffraction, transmission electron microscope based selected area electron diffraction, and X‐ray photoelectron spectroscopy. A flow reactor equipped with a gas diffusion electrode is utilized to test a copper‐based catalyst enriched with the Cu₄O₃ phase under CO₂ reduction conditions. The Cu₄O₃‐rich catalyst (PrC) shows a Faradaic efficiency for ethylene over 40% at 400 mA cm^?2. At ?0.64 versus reversible hydrogen electrode, the highest C₂₊/C₁ product ratio of 4.8 is achieved, with C₂₊ Faradaic efficiency over 61%. Additionally, the catalyst exhibits a stable performance for 24 h at a constant current density of 200 mA cm^?2.