Metal toxicity characterization factors for marine ecosystems—considering the importance of the estuary for freshwater emissions

Purpose

The study develops site-dependent characterization factors (CFs) for marine ecotoxicity of metals emitted to freshwater, taking their passage of the estuary into account. To serve life cycle assessment (LCA) studies where emission location is often unknown, site-generic marine CFs were developed for metal emissions to freshwater and coastal seawater, respectively. The new CFs were applied to calculate endpoint impact scores for the same amount of metal emission to each compartment, to compare the relative ecotoxicity damages in freshwater and marine ecosystems in LCA.

Methods

Site-dependent marine CFs for emission to freshwater were calculated for 64 comparatively independent seas (large marine ecosystems, LMEs). The site-dependent CF was calculated as the product of fate factor (FF), bioavailability factor (BF), and effect factor (EF). USEtox modified with site-dependent parameters was extended with an estuary removal process to calculate FF. BF and EF were taken from Dong et al. Environ Sci Technol 50:269–278 (2016). Site-generic marine CFs were derived from site-dependent marine CFs. Different averaging principles were tested, and the approach representing estuary discharge rate was identified as the best one. Endpoint marine and freshwater metals CFs were developed to calculate endpoint ecotoxicity impact scores.

Results and discussion

Marine ecotoxicity CFs are 1.5 orders of magnitude lower for emission to freshwater than for emission to seawater for Cr, Cu, and Pb, due to notable removal fractions both in freshwater and estuary. For the other metals, the difference is less than half an order of magnitude, mainly due to removal in freshwater. The site-dependent CFs generally vary within two orders of magnitude around the site-generic CF. Compared to USES-LCA 2.0 CFs (egalitarian perspective), the new site-generic marine CFs for emission to seawater are 1–4 orders of magnitude lower except for Pb. The new site-generic marine CFs for emission to freshwater lie within two orders of magnitude difference from USES-LCA 2.0 CFs. The comparative contribution share analysis shows a poor agreement of metal toxicity ranking between both methods.

Conclusions

Accounting for estuary removal particularly influences marine ecotoxicity CFs for emission to freshwater of metals that have a strong tendency to complex-bind to particles. It indicates the importance of including estuary in the characterization modelling when dealing with those metals. The resulting endpoint ecotoxicity impact scores are 1–3 orders of magnitude lower in seawater than in freshwater for most metals except Pb, illustrating the higher sensitivity of freshwater ecosystems to metal emissions, largely due to the higher species density there.

     

Implications of considering metal bioavailability in estimates of freshwater ecotoxicity: examination of two case studies

Purpose  

Previous methods of estimating characterization factors (CFs) of metals in life cycle impact assessment (LCIA) models were based on multimedia fate, exposure, and effect models originally developed to address the potential impacts of organic chemicals. When applied to metals, the models neglect the influence of ambient chemistry on metal speciation, bioavailability and toxicity. Gandhi et al. (2010) presented a new method of calculating CFs for freshwater ecotoxicity that addresses these metal-specific issues. In this paper, we compared and assessed the consequences of using the new method versus currently available LCIA models for calculating freshwater ecotoxicity, as applied to two case studies previously examined by Gloria et al. (2006): (1) the production of copper (Cu) pipe and (2) a zinc (Zn) gutter system.     

Uncertainty and spatial variability in characterization factors for aquatic acidification at the global scale

Purpose

Characterization factors (CFs) quantifying the potential impact of acidifying emissions on inland aquatic environments in life cycle assessment are typically available on a generic level. The lack of spatial differentiation may weaken the relevance of generic CFs since it was shown that regional impact categories such as aquatic acidification were influenced by the surroundings of the emission location. This paper presents a novel approach for the development of spatially differentiated CFs at a global scale for the aquatic acidification impact category.

Methods

CFs were defined as the change in relative decrease of lake fish species richness due to a change in acidifying chemicals emissions. The characterization model includes the modelling steps linking emission to atmospheric acid deposition (atmospheric fate factor) change, which lead to lake H⁺ concentration (receiving environment fate factor) change and a decrease in relative fish species richness (effect factor). We also evaluated the significance of each factor (i.e. atmospheric fate, receiving environment fate and effects) to the overall CFs spatial variability and parameter uncertainty.

Results and discussion

The highest CFs were found for emissions occurring in Canada, Scandinavia and the northern central Asia because of the extensive lake areas in these regions (lake areas being one of the parameters of the CFs; the bigger the lake areas, the higher the CFs). The CFs’ spatial variability ranged over 5, 6 and 8 orders of magnitude for NO_x, SO₂ and NH₃ emissions, respectively. We found that the aquatic receiving environment fate factor is the dominant contributor to the overall spatial variability of the CFs, while the effect factors contributed to 98 % of the total parameter uncertainty.

Conclusions

The resulting characterization model and factors enable a consistent evaluation of spatially explicit acidifying emissions impacts at the global scale.     

Characterization factors for zinc terrestrial ecotoxicity including speciation

Purpose

Ignoring metal speciation in the determination of characterization factors (CFs) in life cycle assessment (LCA) could significantly alter the validity of LCA results since toxicity is directly linked to bioavailability.

Methods

Zinc terrestrial ecotoxicity CFs are obtained using modified USEtox fate factors, WHAM 6.0-derived bioavailable factors, and effect factors calculated using the assessment of mean impact (AMI) method with available terrestrial ecotoxicity data. Soil archetypes created using influent soil properties on Zn speciation (soil texture, pH, cation exchange capacity, organic matter and carbonate contents) are used to group soils of the world into a more manageable spatial resolution for LCA. An aggregated global CF value is obtained using population density as a Zn emission proxy. Results are presented in a world map to facilitate use.

Results and discussion

When using soluble Zn as the bioavailable fraction, CF values vary over 1.76 orders of magnitude, indicating that a single aggregated value could reasonably be used for the world. When using true solution Zn, CFs cover 14 orders of magnitude. To represent this variability, 518 archetypes and 13 groups of archetypes were created. Aggregated global default values are 4.58 potentially affected fraction of species (PAF) m³·day kg^?1 for soluble Zn and 1.45 PAF m³·day kg^?1 for true solution Zn. These values are respectively 28 and 88 times lower than the Zn terrestrial CF in IMPACT 2002 (128 PAF m³·day kg^?1).

Conclusions

The CFs obtained for Zn, except for soluble Zn, are at least 2 orders of magnitude lower than current CFs. However, they must be tested in case studies to measure the impact of including Zn speciation in the CF definition of terrestrial ecotoxicity.

     

Life cycle assessment of a waste lubricant oil management system

Purpose

This paper compares 16 waste lubricant oil (WLO) systems (15 management alternatives and a system in use in Portugal) using a life cycle assessment (LCA). The alternatives tested use various mild processing techniques and recovery options: recycling during expanded clay production, recycling and electric energy production, re-refining, energy recovery during cement production, and energy recovery during expanded clay production.

Methods

The proposed 15 alternatives and the actual present day situation were analyzed using LCA software UMBERTO 5.5, applied to eight environmental impact categories. The LCA included an expansion system to accommodate co-products.

Results

The results show that mild processing with low liquid gas fuel consumption and re-refining is the best option to manage WLO with regard to abiotic depletion, eutrophication, global warming, and human toxicity environmental impacts. A further environmental option is to treat the WLO using the same mild processing technique, but then send it to expanded clay recycling to be used as a fuel in expanded clay production, as this is the best option regarding freshwater sedimental ecotoxicity, freshwater aquatic ecotoxicity, and acidification.

Conclusions

It is recommended that there is a shift away from recycling and electric energy production. Although sensitivity analysis shows re-refining and energy recovery in expanded clay production are sensitive to unit location and substituted products emission factors, the LCA analysis as a whole shows that both options are good recovery options; re-refining is the preferable option because it is closer to the New Waste Framework Directive waste hierarchy principle.     

Freshwater ecotoxicity characterization factors for aluminum

Purpose

Aluminum (Al) is an abundant, non-essential element with complex geochemistry and aquatic toxicity. Considering its complex environmental behavior is critical for providing a reasonable estimate of its potential freshwater aquatic ecotoxicity in the context of Life Cycle Impact Assessment (LCIA).

Methods

Al characterization factors (CFs) are calculated using the following: (1) USEtox^? model version 2.1 for environmental fate, (2) MINEQL+ to estimate the distribution of Al between the solid phase precipitate and total dissolved Al, (3) WHAM 7 for Al speciation within the total dissolved phase, and (4) Biotic Ligand Model (BLM) and Free Ion Activity Model (FIAM) for ecotoxicity estimation for seven freshwater archetypes and default landscape properties for the European continent. The sensitivity of the CFs to aquatic chemistry parameters is calculated. New CFs are compared with Dong et al. (Chemosphere 112:26–33, 2014) and default CF calculated by USEtox 2.1.

Results and discussion

Al CFs vary over 5 orders of magnitude between the seven archetypes, with an arithmetic average CF_ave of 0.04 eq 1,4-DCB (recommended for use), geometric mean CF_geo of 0.0014 eq 1,4-DCB, and weighted average CF_wt of 0.026 eq 1,4-DCB. These values are lower (less toxic) than those for Cu, Ni, Zn, and Pb (with one exception). The effect factor (EF) contributed most to this variability followed by the bioavailability factor (BF), varying over 8 and 4 orders of magnitude, respectively. These revised CFs are 2–6 orders of magnitude lower than those presented by Dong et al. (Chemosphere 112:26–33, 2014) mainly because of consideration of Al precipitation.

Conclusions

Freshwater archetype-specific Al CFs for freshwater ecotoxicity that address the effect of Al speciation on bioavailability (BF) and ecotoxicity (EF) have been calculated, and a CF of 0.04 eq 1,4-DCB is recommended for use in generic LCA. For site-specific LCA, the choice of water chemistry and, in particular, pH, and consideration of metal precipitation could significantly influence results.

Practical implications

Incorporating estimates of metal speciation and its effect on aquatic toxicity is essential when conducting LCIA. Along with metal speciation estimates, the values derived from the definition of water chemistry parameters must also be included into LCIA. For site-generic assessments, we recommend using the arithmetic average of metal CFs. We also recommend using FIAM as a suitable alternative to BLM to estimate EF if the latter is not available. Consideration of metal speciation is essential for providing more realistic estimates of Al freshwater ecotoxicity in the context of LCIA.

     

Land use impacts on freshwater regulation, erosion regulation, and water purification: a spatial approach for a global scale level

Purpose

Rarely considered in environmental assessment methods, potential land use impacts on a series of ecosystem services must be accounted for in widely used decision-making tools such as life cycle assessment (LCA). The main goal of this study is to provide an operational life cycle impact assessment characterization method that addresses land use impacts at a global scale by developing spatially differentiated characterization factors (CFs) and assessing the extent of their spatial variability using different regionalization levels.

Methods

The proposed method follows the recommendations of previous work and falls within the framework and principles for land use impact assessment established by the United Nations Environment Programme/Society of Environmental Toxicology and Chemistry Life Cycle Initiative. Based on the spatial approach suggested by Saad et al. (Int J Life Cycle Assess 16: 198–211, 2011), the intended impact pathways that are modeled pertain to impacts on ecosystem services damage potential and focus on three major ecosystem services: (1) erosion regulation potential, (2) freshwater regulation potential, and (3) water purification potential. Spatially-differentiated CFs were calculated for each biogeographic region of all three regionalization scale (Holdridge life regions, Holdridge life zones, and terrestrial biomes) along with a nonspatial world average level. In addition, seven land use types were assessed considering both land occupation and land transformation interventions.

Results and discussion

A comprehensive analysis of the results indicates that, when compared to all resolution schemes, the world generic averaged CF can deviate for various ecosystem types. In the case of groundwater recharge potential impacts, this range varied up to factors of 7, 4.7, and 3 when using the Holdridge life zones, the Holdridge regions, and the terrestrial biomes regionalization levels, respectively. This validates the importance of introducing a regionalized assessment and highlights how a finer scale increases the level of detail and consequently the discriminating power across several biogeographic regions, which could not have been captured using a coarser scale. In practice, the implementation of such regionalized CFs suggests that an LCA practitioner must identify the ecosystem in which land occupation or transformation activities occur in addition to the traditional inventory data required—namely, the land use activity and the inventory flow.

Conclusions

The variability of CFs across all three regionalization levels provides an indication of the uncertainty linked to nonspatial CFs. Among other assumptions and value choices made throughout the study, the use of ecological borders over political boundaries was deemed more relevant to the interpretation of environmental issues related to specific functional ecosystem behaviors.     

Supporting a transition towards sustainable circular economy: sensitivity analysis for the interpretation of LCA for the recovery of electric and electronic waste

Purpose

The interpretation is a fundamental phase of life cycle assessment (LCA). It ensures the robustness and the reliability of the overall study. Moving towards more circular economy requires that different waste management options are systematically scrutinized to assess the environmental impacts and benefits associated to them. The present work aims at illustrating how a sensitivity analysis could be applied to the impact assessment step supporting the interpretation of a LCA study applied to a waste management system that includes material recovering. The focus is on toxicity-related and resource-related potential impacts as they are considered among the most critical ones, which may affect the way the final benefit from material recovery is evaluated.

Methods

Possible alternatives in terms of impact assessment assumptions and modelling are tested by performing a sensitivity analysis on a case study on electric and electronic waste. For the toxicity-related impact categories, first, a sensitivity analysis is performed using different sets of characterization factors for metals aiming at identifying how they are affecting the final results. Then, an analysis of the relative contribution of long-term emissions in upstream processes is carried out aiming at unveiling critical issues associated to their inclusion or exclusion. For the resource depletion impact category, a sensitivity analysis has been performed, adopting different sets of characterization factors based on existing models for minerals and metals as well as recently proposed sets accounting for critical raw materials.

Results and discussion

The indicator of the ecotoxicity impact category obtained by applying the updated characterization factors is about three times higher than the corresponding obtained by the USEtox model. The long-term emission result is responsible for the major part of all the toxicity impact indicators. Moreover, for the ecotoxicity indicator, excluding the long-term emissions changes the total results from being negative into positive. The sensitivity analysis for the resource depletion impact category shows that all the models applied result in a total avoided impact. A quantitative comparison among all the results is not possible as the different models use different units of measure.

Conclusions

The application of LCA is crucial for assessing avoided impacts and uncovers potential impacts due to recycling. However, contrasting results may stem from the application of different assumptions and models for characterization. A robust interpretation of the results should be based on systematic assessment of the differences highlighted by the sensitivity, as guidance for delving into further analysis of the drivers of impacts and/or to steer ecoinnovation to reduce those impacts.

     

UNEP-SETAC guideline on global land use impact assessment on biodiversity and ecosystem services in LCA

Purpose

As a consequence of the multi-functionality of land, the impact assessment of land use in Life Cycle Impact Assessment requires the modelling of several impact pathways covering biodiversity and ecosystem services. To provide consistency amongst these separate impact pathways, general principles for their modelling are provided in this paper. These are refinements to the principles that have already been proposed in publications by the UNEP-SETAC Life Cycle Initiative. In particular, this paper addresses the calculation of land use interventions and land use impacts, the issue of impact reversibility, the spatial and temporal distribution of such impacts and the assessment of absolute or relative ecosystem quality changes. Based on this, we propose a guideline to build methods for land use impact assessment in Life Cycle Assessment (LCA).

Results

Recommendations are given for the development of new characterization models and for which a series of key elements should explicitly be stated, such as the modelled land use impact pathways, the land use/cover typology covered, the level of biogeographical differentiation used for the characterization factors, the reference land use situation used and if relative or absolute quality changes are used to calculate land use impacts. Moreover, for an application of the characterisation factors (CFs) in an LCA study, data collection should be transparent with respect to the data input required from the land use inventory and the regeneration times. Indications on how generic CFs can be used for the background system as well as how spatial-based CFs can be calculated for the foreground system in a specific LCA study and how land use change is to be allocated should be detailed. Finally, it becomes necessary to justify the modelling period for which land use impacts of land transformation and occupation are calculated and how uncertainty is accounted for.

Discussion

The presented guideline is based on a number of assumptions: Discrete land use types are sufficient for an assessment of land use impacts; ecosystem quality remains constant over time of occupation; time and area of occupation are substitutable; transformation time is negligible; regeneration is linear and independent from land use history and landscape configuration; biodiversity and multiple ecosystem services are independent; the ecological impact is linearly increasing with the intervention; and there is no interaction between land use and other drivers such as climate change. These assumptions might influence the results of land use Life Cycle Impact Assessment and need to be critically reflected.

Conclusions and recommendations

In this and the other papers of the special issue, we presented the principles and recommendations for the calculation of land use impacts on biodiversity and ecosystem services on a global scale. In the framework of LCA, they are mainly used for the assessment of land use impacts in the background system. The main areas for further development are the link to regional ecological models running in the foreground system, relative weighting of the ecosystem services midpoints and indirect land use.     

Spatially explicit fate factors of phosphorous emissions to freshwater at the global scale

Purpose

The location of a phosphorus emission can strongly affect its expected fate in freshwater. To date, in Life Cycle Assessment (LCA), fate factors for phosphorus emissions have been derived for continents or large countries and had limited spatial resolution. These fate factors do not account sufficiently for local variations and are not applicable globally. In this paper, fate factors for freshwater eutrophication are derived for phosphorus emissions to freshwater on a global scale with a half-degree resolution.

Methods

For this purpose, a new global fate model for phosphorus has been developed on a half-degree resolution. The removal processes taken into account are grid-specific advection, phosphorus retention and water use. Aggregated fate factors based on archetypes and on administrative units are presented.

Results and discussion

The derived fate factors represent the persistence of phosphorus in the freshwater environment. The typical fate factor of phosphorus emissions to freshwater is 10?days and can vary more than 2 orders of magnitude among the grid cells (the 5th and 95th percentile are 0.8 and 310?days, respectively). Advection is the dominant removal process of phosphorus in freshwater (67.5%), followed by retention (27.6%) and water use (4.9%).

Conclusions

The results demonstrate inclusion of information on the location of phosphorus emissions to freshwater can improve the comparative power of the fate factor implementation in LCAs. The fate factors enable consistent assessment and comparison of freshwater eutrophication impacts at different locations across the globe.     

A comparative life cycle assessment of two treatment technologies for the Grey Lanaset G textile dye: biodegradation by Trametes versicolor and granular activated carbon adsorption

Purpose

The aim of this study is to use life cycle assessment (LCA) to compare the relative environmental performance of the treatment using Trametes versicolor with a common method such as activated carbon adsorption. This comparison will evaluate potential environmental impacts of the two processes. This work compiles life cycle inventory data for a biological process that may be useful for other emergent biotechnological processes in water and waste management. LCA was performed to evaluate the use of a new technology for the removal of a model metal-complex dye, Grey Lanaset G, from textile wastewater by means of the fungus T. versicolor. This biological treatment was compared with a conventional coal-based activated carbon adsorption treatment to determine which alternative is preferable from an environmental point of view.

Materials and methods

The study is based on experimental research that has tested the novel process at the pilot scale. The analysis of the biological system ranges from the production of the electricity and ingredients required for the growth of the fungus and ends with the composting of the residual biomass from the process. The analysis of the activated carbon system includes the production of the adsorbent material and the electricity needed for the treatment and regeneration of the spent activated carbon. Seven indicators that measure the environmental performance of these technologies are included in the LCA. The indicators used are climate change, ozone depletion, human toxicity, photochemical oxidant formation, terrestial acidification, freshwater eutrophication, marine eutrophication, terrestrial ecotoxicity, freshwater ecotoxicity, marine ecotoxicity, metal depletion and fossil depletion.

Results

The results show that the energy use throughout the biological process, mainly for sterilisation and aeration, accounts for the major environmental impacts with the inoculum sterilisation being the most critical determinant. Nevertheless, the biological treatment has lower impacts than the physicochemical system in six of these indicators when steam is generated directly on site. A low-grade carbon source as an alternative to glucose might contribute to reduce the eutrophication impact of this process.

Conclusions

The LCA shows that the biological treatment process using the fungus T. versicolor to remove Grey Lanaset G offers important environmental advantages in comparison with the traditional activated carbon adsorption method. This study also provides environmental data and an indication of the potential impacts of characteristic processes that may be of interest for other applications in the field of biological waste treatment and wastewater treatment involving white-rot fungi.     

Life cycle assessment of a biobased chainsaw oil made on the farm in Wallonia

Purpose

The environmental issue is a particular concern for chainsaw oils because these fluids represent a total loss system. The aim of this study is to quantify the environmental impacts of a biobased chainsaw oil made on the farm in Wallonia (a region of Belgium) and to compare it with a model mineral chainsaw oil. With this study, the aim is also to participate in the development of the life cycle assessment (LCA) methodology applied to the biolubricant sector since LCAs on these products are quite limited and rarely sufficiently detailed.

Method

In this LCA, the attributional approach is applied. Seven impact categories are studied. The methods for life cycle impact assessment are IPCC, ReCiPe, CML and USEtox. The functional unit is 1 kg of base oil. Seven sensitivity analyses are performed.

Results and discussion

Results indicate that the biobased chainsaw oil made on the farm has a lower impact for the global warming potential, the abiotic depletion potential, the ozone depletion potential and the photochemical oxidation potential. On the contrary, it has larger acidification, aquatic eutrophication and aquatic ecotoxicity potential impacts. Regarding the contribution of the life cycle stages of the biobased chainsaw oil, the agricultural stage causes the highest contribution in all impact categories. For the mineral chainsaw oil, the refining stage is preponderant for all impact categories except for the global warming potential for which the end-of-life stage contributes the most. When taking additives into account, conclusions regarding the comparison between the oils are not reversed. Even if it was necessary to consume more biobased than mineral chainsaw oil, conclusions regarding the comparison of the oils would not be reversed. In the same way, a different allocation procedure for rapeseed oil and rape meal, a different rape seeds yield or different extraction yields in the refining stage of the mineral base oil do not change the results of the comparison. For the biobased chainsaw oil, the substitution of only one active substance in the agricultural stage could result in an important decrease of the freshwater ecotoxicity impact.

Conclusions

The biobased chainsaw oil has a lower impact in four out of the seven impact categories and a higher impact in three impact categories. By providing a detailed LCA on a biobased chainsaw oil, this study contributes to the development of LCA applied to biobased lubricants.     

The influence of value choices in life cycle impact assessment of stressors causing human health damage

Purpose

This study analyzes the influence of value choices in impact assessment models for human health, such as the choice of time horizon, on life cycle assessment outcomes.

Methods

For 756 products, the human health damage score is calculated using three sets of characterization factors (CFs). The CFs represent seven human health impact assessment categories: water scarcity, tropospheric ozone formation, particulate matter formation, human toxicity, ionizing radiation, stratospheric ozone depletion, and climate change. Each set of CFs embeds a combination of value choices following the Cultural Theory, and reflects the individualist, hierarchist, or egalitarian perspective.

Results

We found that the average difference in human health damage score goes from 1 order of magnitude between the individualist and hierarchist perspectives to 2.5 orders of magnitude between the individualist and egalitarian perspectives. The difference in damage score of individual materials among perspectives depends on the combination of emissions driving the impact of both perspectives and can rise up to 5 orders of magnitude.

Conclusions

The value choices mainly responsible for the differences in results among perspectives are the choice of time horizon and inclusion of highly uncertain effects. A product comparison can be affected when the human health damage score of two products differ less than a factor of 5, or the comparing products largely differ in their emitted substances. Overall, our study implies that value choices in impact assessment modeling can modify the outcomes of a life cycle assessment (LCA) and thus the practical implication of decisions based on the results of an LCA.     

Temporal differentiation of background systems in LCA: relevance of adding temporal information in LCI databases

Purpose

Because the potential impacts of emissions and extractions can be sensitive to timing, the temporal aggregation of life cycle inventory (LCI) data has often been cited as a limitation in life cycle assessment (LCA). Until now, examples of temporal emission and extraction distributions were restricted to the foreground processes of product systems. The objective of this paper is to evaluate the relevance of considering the temporal distribution of the background system inventory.

Methods

The paper focuses on the global warming impact category for which so-called dynamic characterization factors (CFs) were developed and uses the ecoinvent v2.2 database as both an example database to which temporal information can be added and a source of product systems to test the relevance of adding temporal information to the background system. Temporal information was added to the elementary and intermediate exchanges of 22 % of the unit processes in the database. Using the enhanced structure path analysis (ESPA) method to generate temporally differentiated LCIs in conjunction with time-dependent global warming characterization factors, potential impacts were calculated for all 4,034 product systems in the ecoinvent database.

Results and discussion

Each time, the results were calculated for (1) systems in which temporal information was only added to the first two tiers, representing studies in which only the foreground system is temporally differentiated, and (2) systems in which temporal information was also added to the background system. For 8.6 % of the database product systems, adding temporal differentiation to background unit processes affected the global warming impact scores by more than 10 %. For most of the affected product systems, considering temporal information in the background unit processes decreased the global warming impact scores. The sectors that show most sensitivity to the temporal differentiation of background unit processes are associated with wood and biofuel sectors.

Conclusions

Even though the addition of temporal information to unit processes in LCI databases would not benefit every LCA study, the enhancement can be relevant. It allows for a more accurate global warming impact assessment, especially for LCAs in which products of biomass are present in substantial amounts. Relevance for other impact categories could be discussed in further work.     

Including metal atmospheric fate and speciation in soils for terrestrial ecotoxicity in life cycle impact assessment

Purpose

The aim of the study is to calculate regionalized characterization factors for the atmospheric emissions of metals transferred to soil for zinc, copper, and nickel taking into account the atmospheric fate and speciation.

Methods

In order to calculate characterization factors for all possible atmospheric emission locations around the world, the link between atmospheric deposition with regionalized soil fate factors and bioavailability factors accounting for the metal’s speciation was established. The methodology to develop the regionalized fate factors and characterization factors is threefold. First, the emitted metal fraction that is deposited on soils is calculated from atmospheric source-receptor matrices providing for each emission location the fraction of an emission that is deposited on each worldwide receiving cell (2°?×?2.5° resolution). Second, the fraction of metal deposited in different soil types is determined by overlapping the deposition map with a soil map, based on the 4513 different soil types from the Harmonized World Soil Database. Third, bioavailability factors are calculated for each soil type, which allows determining the bioavailable fraction of the deposited metal depending on the soil properties. Combining these steps with the effect factors results in a series of terrestrial ecotoxicological characterization factors. These characterization factors are then applied in an illustrative example and compared to results obtained with generic characterization factors. The case study focuses on the electricity production process in Québec, whose ecosystem impacts are currently dominated by metal ecotoxicity impacts. The uncertainty due to the spatial variability of the impact is quantified.

Results and discussion

Our results show that regionalized characterization factors are over three orders of magnitude lower than generic characterization factors. They are presented on maps and their spatial variability was evaluated at different regional scales (region, country, world). The use of regionalized characterization factors with their spatial variability at different geographic resolution scales in the case study gives a result more or less precise depending on the level of resolution of the characterization factor applied (country or global-default). The impact scores of the three metals in the case study are three orders of magnitude lower when compared to the scores obtained with generic characterization factors.

Conclusions

The development of those regionalized characterization factors improves the terrestrial ecotoxicity assessment in life cycle impact assessment by taking into account the atmospheric fate and the speciation of the metal for new 3 metals for the different soil types in the world and by documenting their spatial variability.

     

Assessing freshwater use impacts in LCA: Part I—inventory modelling and characterisation factors for the main impact pathways

Background, aim and scope

Freshwater is a basic resource for humans; however, its link to human health is seldom related to lack of physical access to sufficient freshwater, but rather to poor distribution and access to safe water supplies. On the other hand, freshwater availability for aquatic ecosystems is often reduced due to competition with human uses, potentially leading to impacts on ecosystem quality. This paper summarises how this specific resource use can be dealt with in life cycle analysis (LCA).

Main features

The main quantifiable impact pathways linking freshwater use to the available supply are identified, leading to definition of the flows requiring quantification in the life cycle inventory (LCI).

Results

The LCI needs to distinguish between and quantify evaporative and non-evaporative uses of ‘blue’ and ‘green’ water, along with land use changes leading to changes in the availability of freshwater. Suitable indicators are suggested for the two main impact pathways [namely freshwater ecosystem impact (FEI) and freshwater depletion (FD)], and operational characterisation factors are provided for a range of countries and situations. For FEI, indicators relating current freshwater use to the available freshwater resources (with and without specific consideration of water ecosystem requirements) are suggested. For FD, the parameters required for evaluation of the commonly used abiotic depletion potentials are explored.

Discussion

An important value judgement when dealing with water use impacts is the omission or consideration of non-evaporative uses of water as impacting ecosystems. We suggest considering only evaporative uses as a default procedure, although more precautionary approaches (e.g. an ‘Egalitarian’ approach) may also include non-evaporative uses. Variation in seasonal river flows is not captured in the approach suggested for FEI, even though abstractions during droughts may have dramatic consequences for ecosystems; this has been considered beyond the scope of LCA.

Conclusions

The approach suggested here improves the representation of impacts associated with freshwater use in LCA. The information required by the approach is generally available to LCA practitioners

Recommendations and perspectives

The widespread use of the approach suggested here will require some development (and consensus) by LCI database developers. Linking the suggested midpoint indicators for FEI to a damage approach will require further analysis of the relationship between FEI indicators and ecosystem health.     

Life cycle assessment in the minerals and metals sector: a critical review of selected issues and challenges

Background, aim and scope

The mining sector provides materials that are essential elements in a wide range of goods and services, which create value by meeting human needs. Mining and processing activities are an integral part of most complex material cycles so that the application of life cycle assessment (LCA) to minerals and metals has therefore gained prominence. In the past decade, increased use of LCA in the mineral and metal sector has advanced the scientific knowledge through the development of scientifically valid life cycle inventory databases. Though scientifically valid, LCA still needs to depend on several technical assumptions. In particular, measuring the environmental burden issues related to abiotic resource depletion, land use impacts and open-loop recycling within the LCA are widely debated issues. Also, incorporating spatial and temporal sensitivities in LCA, to make it a consistent scientific tool, is yet to be resolved. This article discusses existing LCA methods and proposed models on different issues in relation to minerals and metals sector.

Main features

A critical review was conducted of existing LCA methods in the minerals and metals sector in relation to allocation issues related to indicators of land use impacts, abiotic resource depletion, allocation in open-loop recycling and the system expansions and accounting of spatial and temporal dimension in LCA practice.

Results

Evolving a holistic view about these contentious issues will be presented with view for future LCA research in the minerals and metals industry. This extensive literature search uncovers many of the issues that require immediate attention from the LCA scientific community.

Discussion

The methodological drawbacks, mainly problems with inconsistencies in LCA results for the same situation under different assumptions and issues related to data quality, are considered to be the shortcomings of current LCA. In the minerals and metals sector, it is important to increase the objectivity of LCA by way of fixing those uncertainties, for example, in the LCA of the minerals and metals sector, whether the land use has to be considered in detail or at a coarse level. In regard to abiotic resource characterisation, the weighting and time scales to be considered become a very critical issue of judgement. And, in the case of open-loop recycling, which model will best satisfy all the stake holders? How the temporal and spatial dimensions should be incorporated into LCA is one of the biggest challenges ahead of all those who are concerned. Addressing these issues shall enable LCA to be used as a policy tool in environmental decision-making. There has been enormous debate with respect to on land use impacts, abiotic resource depletion, open-loop recycling and spatial and temporal dimensions, and these debates remain unresolved. Discussions aimed at bringing consensus amongst all the stake holders involved in LCA (i.e. industry, academia, consulting organisations and government) will be presented and discussed. In addition, a commentary of different points of view on these issues will be presented.

Conclusions

This review shall bring into perspective some of those contentious issues that are widely debated by many researchers. The possible future directions proposed by researchers across the globe shall be presented. Finally, authors conclude with their views on the prospects of LCA for future research endeavours.

Recommendations and outlook

Specific LCA issues of minerals and metals need to be investigated further to gain more understanding. To facilitate the future use of LCA as a policy tool in the minerals and metals sector, it is important to increase the objectivity with more scientific validity. Therefore, it is essential that the issues discussed in this paper are addressed to a great detail.     

Dynamic life cycle assessment: framework and application to an institutional building

Purpose

This paper uses a dynamic life cycle assessment (DLCA) approach and illustrates the potential importance of the method using a simplified case study of an institutional building. Previous life cycle assessment (LCA) studies have consistently found that energy consumption in the use phase of a building is dominant in most environmental impact categories. Due to the long life span of buildings and potential for changes in usage patterns over time, a shift toward DLCA has been suggested.

Methods

We define DLCA as an approach to LCA which explicitly incorporates dynamic process modeling in the context of temporal and spatial variations in the surrounding industrial and environmental systems. A simplified mathematical model is used to incorporate dynamic information from the case study building, temporally explicit sources of life cycle inventory data and temporally explicit life cycle impact assessment characterization factors, where available. The DLCA model was evaluated for the historical and projected future environmental impacts of an existing institutional building, with additional scenario development for sensitivity and uncertainty analysis of future impacts.

Results and discussion

Results showed that overall life cycle impacts varied greatly in some categories when compared to static LCA results, generated from the temporal perspective of either the building's initial construction or its recent renovation. From the initial construction perspective, impacts in categories related to criteria air pollutants were reduced by more than 50 % when compared to a static LCA, even though nonrenewable energy use increased by 15 %. Pollution controls were a major reason for these reductions. In the future scenario analysis, the baseline DLCA scenario showed a decrease in all impact categories compared with the static LCA. The outer bounds of the sensitivity analysis varied from slightly higher to strongly lower than the static results, indicating the general robustness of the decline across the scenarios.

Conclusions

These findings support the use of dynamic modeling in life cycle assessment to increase the relevance of results. In some cases, decision making related to building design and operations may be affected by considering the interaction of temporally explicit information in multiple steps of the LCA. The DLCA results suggest that in some cases, changes during a building's lifetime can influence the LCA results to a greater degree than the material and construction phases. Adapting LCA to a more dynamic approach may increase the usefulness of the method in assessing the performance of buildings and other complex systems in the built environment.     

Assessment of urgent impacts of greenhouse gas emissions—the climate tipping potential (CTP)

Purpose

The impact of anthropogenic greenhouse gas (GHG) emissions on climate change receives much focus today. This impact is however often considered only in terms of global warming potential (GWP), which does not take into account the need for staying below climatic target levels, in order to avoid passing critical climate tipping points. Some suggestions to include a target level in climate change impact assessment have been made, but with the consequence of disregarding impacts beyond that target level. The aim of this paper is to introduce the climate tipping impact category, which represents the climate tipping potential (CTP) of GHG emissions relative to a climatic target level. The climate tipping impact category should be seen as complementary to the global warming impact category.

Methods

The CTP of a GHG emission is expressed as the emission’s impact divided by the ‘capacity’ of the atmosphere for absorbing the impact without exceeding the target level. The GHG emission impact is determined as its cumulative contribution to increase the total atmospheric GHG concentration (expressed in CO₂ equivalents) from the emission time to the point in time where the target level is expected to be reached, the target time.

Results and discussion

The CTP of all the assessed GHGs increases as the emission time approaches the target time, reflecting the rapid decrease in remaining atmospheric capacity and thus the increasing potential impact of the GHG emission. The CTP of a GHG depends on the properties of the GHG as well as on the chosen climatic target level and background scenario for atmospheric GHG concentration development. In order to enable direct application in life cycle assessment (LCA), CTP characterisation factors are presented for the three main anthropogenic GHGs, CO₂, CH₄ and N₂O.

Conclusions

The CTP metric distinguishes different GHG emission impacts in terms of their contribution to exceeding a short-term target and highlights their increasing importance when approaching a climatic target level, reflecting the increasing urgency of avoiding further GHG emissions in order to stay below the target level. Inclusion of the climate tipping impact category for assessing climate change impacts in LCA, complimentary to the global warming impact category which shall still represent the long-term climate change impacts, is considered to improve the value of LCA as a tool for decision support for climate change mitigation.