Bonding of Resin Cement to Zirconia with High Pressure Primer Coating

Objectives

To investigate the effect of air-drying pressure during ceramic primer coating on zirconia/resin bonding and the surface characteristics of the primed zirconia.

Methods

Two ceramic primers (Clearfil Ceramic Primer, CCP, Kuraray Medical Inc. and Z-Prime Plus, ZPP, Bisco Inc.) were applied on the surface of air-abraded zirconia (Katana zirconia, Noritake) and dried at 4 different air pressures (0.1–0.4 MPa). The primed zirconia ceramic specimens were bonded with a resin-based luting agent (SA Luting Cement, Kuraray). Micro-shear bond strengths of the bonded specimens were tested after 3 days of water storage or 5,000× thermocycling (n = 12). Failure modes of the fractured specimens were examined with scanning electron miscopy. The effects of air pressure on the thickness of the primer layers and the surface roughness (S_a) of primed zirconia were evaluated using spectroscopic ellipsometry (n = 6), optical profilometry and environmental scanning electron microscopy (ESEM) (n = 6), respectively.

Results

Clearfil Ceramic Primer air-dried at 0.3 and 0.4 MPa, yielding significantly higher µSBS than gentle air-drying subgroups (p<0.05). Compared to vigorous drying conditions, Z-Prime Plus air-dried at 0.2 MPa exhibited significantly higher µSBS (p<0.05). Increasing air-drying pressure reduced the film thickness for both primers. Profilometry measurements and ESEM showed rougher surfaces in the high pressure subgroups of CCP and intermediate pressure subgroup of ZPP.

Conclusion

Air-drying pressure influences resin/zirconia bond strength and durability significantly. Higher air-drying pressure (0.3-0.4 MPa) for CCP and intermediate pressure (0.2 MPa) for ZPP are recommended to produce strong, durable bonds between resin cement and zirconia ceramics.     

Effects of Mechanical and Chemical Pretreatments of Zirconia or Fiber Posts on Resin Cement Bonding

The bonding strength between resin cement and posts is important for post and core restorations. An important method of improving the bonding strength is the use of various surface pretreatments of the post. In this study, the surfaces of zirconia (fiber) posts were treated by mechanical and/or chemical methods such as sandblasting and silanization. The bonding strength between the zirconia (fiber) post and the resin cement was measured by a push-out method after thermocycling based on the adhesion to Panavia F 2.0 resin cement. The zirconia and fiber posts exhibited different bonding strengths after sandblasting and/or silanization because of the different strengths and chemical structures. The zirconia post showed a high bonding strength of up to 17.1 MPa after a combined treatment of sandblasting and silanization because of the rough surface and covalent bonds at the interface. This effect was also enhanced by using 1,2-bis(trimethoxysilyl)ethane for the formation of a flexible layer at the interface. In contrast, a high bonding strength of 13.9 MPa was obtained for the fiber post treated by silane agents because the sandblasting treatment resulted in damage to the fiber post, as observed by scanning electron microscopy. The results indicated that the improvement in the bonding strength between the post and the resin cement could be controlled by different chemical and/or mechanical treatments. Enhanced bonding strength depended on covalent bonding and the surface roughness. A zirconia post with high bonding strength could potentially be used for the restoration of teeth in the future.     

Effect of Er,Cr:YSGG Laser at Different Output Powers on the Micromorphology and the Bond Property of Non-Carious Sclerotic Dentin to Resin Composites

Background

The objective of this study was to investigate the influence of Er,Cr:YSGG laser irradiated at different powers on the micromorphology and the bonding property of non-carious sclerotic dentin to resin composites.

Methods

Two hundred bovine incisors characterized by non-carious sclerotic dentin were selected, and the seventy-two teeth of which for surface morphological analysis were divided into nine groups according to various treatments (A: the control group, B: only treated with the adhesive Adper Easy One, C: diamond bur polishing followed by Adper Easy One, D-I: Er,Cr:YSGG laser irradiating at 1W, 2W, 3W, 4W, 5W, 6W output power, respectively, followed by Adper Easy One). The surface roughness values were measured by the non-contact three-dimensional morphology scanner, then the surface micromorphologies of surfaces in all groups were assessed by scanning electron microscopy (SEM); meanwhile, Image Pro-Plus 6.0 software was used to measure the relative percentage of open tubules on SEM images. The rest, one hundred twenty-eight teeth for bond strength test, were divided into eight groups according to the different treatments (A: only treated with the adhesive Adper Easy One, B: diamond bur polishing followed by the above adhesive, C-H: Er,Cr:YSGG laser irradiating at 1 W, 2 W, 3 W, 4 W, 5 W, 6 W output power, respectively, followed by the above adhesive), and each group was subsequently divided into two subgroups according to whether aging is performed (immediately tested and after thermocycling). Micro-shear bond strength test was used to evaluate the bond strength.

Results

The 4W laser group showed the highest roughness value (30.84±1.93μm), which was statistically higher than the control group and the diamond bur groups (p<0.05). The mean percentages ((27.8±1.8)%, (28.0±2.2)%, (30.0±1.9)%) of open tubules area in the 4W, 5W, 6W group were higher than other groups (p<0.05). The 4W laser group showed the highest micro-shear bond strength not only in immediately tested (17.60±2.55 PMa) but after thermocycling (14.35±2.08MPa).

Conclusion

The Er,Cr:YSGG laser at 4W power can effectively improve the bonding property between non-carious sclerotic dentin and resin composites by increasing the roughness and mean percentage area of open tubules.     

Shear bond strength between different materials bonded with two resin cements

doi: 10.1111/j.1741‐2358.2011.00565.x
Shear bond strength between different materials bonded with two resin cements Background: The aim of this study was to compare the shear bond strength between Ni–Cr alloy specimens bonded to air‐abraded Ni–Cr, bur‐abraded Ni–Cr, etched ceramic and etched enamel substrates using the resin cements RelyX ARC or Enforce. Materials and methods: Ni–Cr specimens were made and sandblasted with Al₂O₃ airborne‐particles. Disc‐shaped patterns were made for each of the four experimental substrates: Ni–Cr treated with Al₂O₃ airborne‐particles, Ni–Cr treated with diamond bur abrasion, etched enamel and etched ceramic. Results: Significant differences in shear bond strength were found between the different materials and luting agents evaluated. The Ni–Cr alloy cylinders bonded to Ni–Cr surfaces sandblasted with 50 μm Al₂O₃ particles and bonded with Enforce achieved the highest bond strength when compared with other substrates (28.9 MPa, p < 0.05). Bur‐abraded metal discs had lowest values, regardless the cement used (2.9 and 6.9 MPa for RelyX and Enforce, respectively). Etched enamel and etched ceramic had similar shear bond strengths within cement groups and performed better when RelyX was used. Conclusions: Bonding Ni–Cr to Ni–Cr and ceramic may result in similar and higher bond strength when compared to Ni–Cr/enamel bonding. For metal/metal bonding, higher shear bond strength was achieved with resin cement Enforce, and for metal/ceramic and metal/enamel bonding, RelyX had higher results.     

Impact of Denture Cleaning Method and Overnight Storage Condition on Denture Biofilm Mass and Composition: A Cross-Over Randomized Clinical Trial

Background

Appropriate oral hygiene is required to maintain oral health in denture wearers. This study aims to compare the role of denture cleaning methods in combination with overnight storage conditions on biofilm mass and composition on acrylic removable dentures.

Methods

In a cross-over randomized controlled trial in 13 older people, 4 conditions with 2 different mechanical cleaning methods and 2 overnight storage conditions were considered: (i) brushing and immersion in water without a cleansing tablet, (ii) brushing and immersion in water with a cleansing tablet, (iii) ultrasonic cleaning and immersion in water without a cleansing tablet, and (iv) ultrasonic cleaning and immersion in water with a cleansing tablet. Each test condition was performed for 5 consecutive days, preceded by a 2-days wash-out period. Biofilm samples were taken at baseline (control) and at the end of each test period from a standardized region. Total and individual levels of selected oral bacteria (n = 20), and of Candida albicans were identified using the Polymerase Chain Reaction (PCR) technique. Denture biofilm coverage was scored using an analogue denture plaque score. Paired t-tests and Wilcoxon-signed rank tests were used to compare the test conditions. The level of significance was set at α< 5%.

Results

Overnight denture storage in water with a cleansing tablet significantly reduced the total bacterial count (p<0.01). The difference in total bacterial level between the two mechanical cleaning methods was not statistically significant. No significant effect was observed on the amount of Candida albicans nor on the analogue plaque scores.

Conclusions

The use of cleansing tablets during overnight denture storage in addition to mechanical denture cleaning did not affect Candida albicans count, but reduced the total bacterial count on acrylic removable dentures compared to overnight storage in water. This effect was more pronounced when combined with ultrasonic cleaning compared to brushing.

Trial Registration

ClinicalTrials.gov {"type":"clinical-trial","attrs":{"text":"NCT02454413","term_id":"NCT02454413"}}NCT02454413     

Impact of Sense of Coherence on Oral Health Behaviors: A Systematic Review

Objectives

The aim of this review was to critically analyze the empirical evidence on the association between Sense of Coherence (SOC) and oral health behaviors through a systematic approach.

Methods

A systematic search up to April 2015 was carried out using the following electronic bibliographic databases: PubMed, Ovid MEDLINE; ISI Web of Science; and Ovid PsychInfo. Studies were included if they evaluated the relationship between SOC and oral health behaviors including tooth cleaning, fluoride usage, dietary habits, dental attendance, and smoking. We excluded studies that only assessed the relationship between oral health status and SOC without evaluating oral health behaviors. The New Castle Ottawa (NOS) quality assessment checklist was employed to evaluate the methodological quality of included studies.

Results

Thirty-nine potential papers met the preliminary selection criteria and following a full-text review, 9 papers were finally selected for this systematic review. Results provided by the included studies indicated different levels of association between SOC and oral health behaviors. The most frequent behaviors investigated were tooth brushing and dental attendance pattern. The impact of SOC on performing positive oral health behaviors, to some extent, was related to demographic and socio-economic factors. In addition, mothers’ SOC influenced children’s oral health practices.

Conclusions

A more favorable oral health behavior was observed among those with a stronger SOC suggesting that the SOC can be a determinant of oral health-related behaviors including tooth brushing frequency, daily smoking, and dental attendance.     

Investigation on the Tribological Behavior and Wear Mechanism of Five Different Veneering Porcelains

Objectives

The primary aim of this research was to investigate the wear behavior and wear mechanism of five different veneering porcelains.

Methods

Five kinds of veneering porcelains were selected in this research. The surface microhardness of all the samples was measured with a microhardness tester. Wear tests were performed on a ball-on-flat PLINT fretting wear machine, with lubrication of artificial saliva at 37°C. The friction coefficients were recorded by the testing system. The microstructure features, wear volume, and damage morphologies were recorded and analyzed with a confocal laser scanning microscope and a scanning electron microscope. The wear mechanism was then elucidated.

Results

The friction coefficients of the five veneering porcelains differ significantly. No significant correlation between hardness and wear volume was found for these veneering porcelains. Under lubrication of artificial saliva, the porcelain with higher leucite crystal content exhibited greater wear resistance. Additionally, leucite crystal size and distribution in glass matrix influenced wear behavior. The wear mechanisms for these porcelains were similar: abrasive wear dominates the early stage, whereas delamination was the main damage mode at the later stage. Furthermore, delamination was more prominent for porcelains with larger crystal sizes.

Significance

Wear compatibility between porcelain and natural teeth is important for dental restorative materials. Investigation on crystal content, size, and distribution in glass matrix can provide insight for the selection of dental porcelains in clinical settings.     

Consumption of Dental Treatment in Patients with Inflammatory Bowel Disease,a Register Study

Objective

The aim of this study was to compare the consumption of dental treatment among patients with Crohn´s disease (CD) or ulcerative colitis (UC) compared to age and gender matched control groups.

Design

The study group comprised 2085 patients with CD and 3161 with UC from the Uppsala-Örebro region and from the Stockholm region. The patients in the cohort were diagnosed between 1960 and 1989. Patients up to 70 years of age were included in the study. The two patients groups were compared to age- and gender-matched, randomly selected control groups from the same geographic area comprising a corresponding number of participants.

Results

CD patients had significantly higher total number of procedures registered (p < 0.000). The difference was most pronounced for removable dentures (+65%), fillings in front teeth (+52%) and endodontic treatment (+46%) when Crohn’s patients were compared to controls (p<0.001). The corresponding figures for UC patients were also a significantly higher total number of procedures (p < 0.005), more clinical examinations (p<0.000), fillings in canines and incisors (p < 0.001) and fillings in bicuspids and molars (p < 0.000).

Conclusion

This study demonstrate that CD and UC individuals use more dental treatment compared to an age-gender matched control group, and more caries-related treatments. The difference was most pronounced for restorative treatment in patients with Crohn’s.     

Re-Examining the Association between Vitamin D and Childhood Caries

Background

Previous studies have reported an inverse association between vitamin D and childhood dental caries, but whether this is causal is unclear.

Objective

To determine the causal effect of circulating 25-hydroxyvitamin D concentration on dental caries experience, early caries onset and the requirement for a dental general anesthetic.

Design

A Mendelian randomization study was undertaken, using genetic variants known to be associated with circulating 25-hydroxyvitamin D concentrations in 5,545 European origin children from the South West of England. Data on caries and related characteristics were obtained from parental and child completed questionnaires between 38 and 91 months and clinical assessments in a random 10% sample at 31, 44 and 61 months.

Results

In multivariable confounder adjusted analyses no strong evidence for an association of 25-hydroxyvitamin D with caries experience or severity was found but there was evidence for an association with early caries onset, or having a general anesthetic for dental problems. In Mendelian randomization analysis the odds ratio for caries experience per 10 nmol/L increase in 25-hydroxyvitamin D was 0.93 (95% confidence interval: 0.83, 1.05; P = 0.26) and the odds ratio for dental general anaesthetic per 10 nmol/L increase in 25-hydroxyvitamin D was 0.96 (95% confidence interval: 0.75, 1.22; P = 0.72).

Conclusions

This Mendelian randomization study provides little evidence to support an inverse causal effect of 25-hydroxyvitamin D on dental caries. However, the estimates are imprecise and a larger study is required to refine these analyses.     

N-Acetyl Cysteine Depletes Reactive Oxygen Species and Prevents Dental Monomer-Induced Intrinsic Mitochondrial Apoptosis In Vitro in Human Dental Pulp Cells

Purpose

To investigate the involvement of intrinsic mitochondrial apoptosis in dental monomer-induced cytotoxicity and the influences of N-acetyl cysteine (NAC) on this process.

Methods

Human dental pulp cells (hDPCs) were exposed to several dental monomers in the absence or presence of NAC, and cell viability, intracellular redox balance, morphology and function of mitochondria and key indicators of intrinsic mitochondrial apoptosis were evaluated using various commercial kits.

Results

Dental monomers exerted dose-dependent cytotoxic effects on hDPCs. Concomitant to the over-production of reactive oxygen species (ROS) and depletion of glutathione (GSH), differential changes in activities of superoxide dismutase, glutathione peroxidase, and catalase were detected. Apoptosis, as indicated by positive Annexin V/propidium iodide (PI) staining and activation of caspase-3, was observed after dental monomer treatment. Dental monomers impaired the morphology and function of mitochondria, and induced intrinsic mitochondrial apoptosis in hDPCs via up-regulation of p53, Bax and cleaved caspase-3, and down-regulation of Bcl-2. NAC restored cell viability, relieved oxidative stress and blocked the apoptotic effects of dental monomers.

Conclusions

Dental monomers induced oxidative stress and mitochondrial intrinsic apoptosis in hDPCs. NAC could reduce the oxidative stress and thus protect hDPCs against dental monomer-induced apoptosis.     

Urban Options for Psychological Restoration: Common Strategies in Everyday Situations

Objectives

Given the need for knowledge on the restorative potential of urban settings, we sought to estimate the effects of personal and contextual factors on preferences and restoration likelihood assessments for different urban activities-in-environments. We also sought to study the generality of these effects across different countries.

Methods

We conducted a true experiment with convenience samples of university students in the Netherlands (n = 80), Sweden (n = 100), and the USA (n = 316). In each country, the experiment had a mixed design with activities-in-environments (sitting in a park, sitting in a cafe, walking in a shopping mall, walking along a busy street) manipulated within-subjects and the need for restoration (attentional fatigue, no attentional fatigue) and immediate social context (in company, alone) manipulated between-subjects. The manipulations relied on previously tested scenarios describing everyday situations that participants were instructed to remember and imagine themselves being in. For each imagined situation (activity-in-environment with antecedent fatigue condition and immediate social context), subjects provided two criterion measures: general preference and the likelihood of achieving psychological restoration.

Results

The settings received different preference and restoration likelihood ratings as expected, affirming that a busy street, often used in comparisons with natural settings, is not representative of the restorative potential of urban settings. Being with a close friend and attentional fatigue both moderated ratings for specific settings. Findings of additional moderation by country of residence caution against broad generalizations regarding preferences for and the expected restorative effects of different urban settings.

Conclusions

Preferences and restoration likelihood ratings for urban activity-environment combinations are subject to multiple personal and contextual determinants, including level of attentional fatigue, being alone versus in company, and broader aspects of the urban context that vary across cities and countries. Claims regarding a lack of restorative quality in urban environments are problematic.     

Magnetic Beads Enhance Adhesion of NIH 3T3 Fibroblasts: A Proof-of-Principle In Vitro Study for Implant-Mediated Long-Term Drug Delivery to the Inner Ear

Introduction

Long-term drug delivery to the inner ear may be achieved by functionalizing cochlear implant (CI) electrodes with cells providing neuroprotective factors. However, effective strategies in order to coat implant surfaces with cells need to be developed. Our vision is to make benefit of electromagnetic field attracting forces generated by CI electrodes to bind BDNF-secreting cells that are labelled with magnetic beads (MB) onto the electrode surfaces. Thus, the effect of MB-labelling on cell viability and BDNF production were investigated.

Materials and Methods

Murine NIH 3T3 fibroblasts—genetically modified to produce BDNF—were labelled with MB.

Results

Atomic force and bright field microscopy illustrated the internalization of MB by fibroblasts after 24 h of cultivation. Labelling cells with MB did not expose cytotoxic effects on fibroblasts and allowed adhesion on magnetic surfaces with sufficient BDNF release.

Discussion

Our data demonstrate a novel approach for mediating enhanced long-term adhesion of BDNF-secreting fibroblasts on model electrode surfaces for cell-based drug delivery applications in vitro and in vivo. This therapeutic strategy, once transferred to cells suitable for clinical application, may allow the biological modifications of CI surfaces with cells releasing neurotrophic or other factors of interest.     

Urease and Dental Plaque Microbial Profiles in Children

Objective

Urease enzymes produced by oral bacteria generate ammonia, which can have a significant impact on the oral ecology and, consequently, on oral health. To evaluate the relationship of urease with dental plaque microbial profiles in children as it relates to dental caries, and to identify the main contributors to this activity.

Methods

82 supragingival plaque samples were collected from 44 children at baseline and one year later, as part of a longitudinal study on urease and caries in children. DNA was extracted; the V3–V5 region of the 16S rRNA gene was amplified and sequenced using 454 pyrosequencing. Urease activity was measured using a spectrophotometric assay. Data were analyzed with Qiime.

Results

Plaque urease activity was significantly associated with the composition of the microbial communities of the dental plaque (Baseline P = 0.027, One Year P = 0.012). The bacterial taxa whose proportion in dental plaque exhibited significant variation by plaque urease levels in both visits were the family Pasteurellaceae (Baseline P<0.001; One Year P = 0.0148), especially Haemophilus parainfluenzae. No association was observed between these bacteria and dental caries. Bacteria in the genus Leptotrichia were negatively associated with urease and positively associated with dental caries (Bonferroni P<0.001).

Conclusions

Alkali production by urease enzymes primarily from species in the family Pasteurellaceae can be an important ecological determinant in children’s dental plaque. Further studies are needed to establish the role of urease-associated bacteria in the acid/base homeostasis of the dental plaque, and in the development and prediction of dental caries in children.     

Impact of Bisphosphonate-related Osteonecrosis of the Jaw on Osteoporotic Patients after Dental Extraction: A Population-Based Cohort Study

Background and Aims

Little is currently known about the risk of developing bisphosphonate-related osteonecrosis of the jaw (BRONJ). This study sought to determine the incidence of BRONJ in osteoporotic patients. We also sought to identify the nature and types of risk factors of osteonecrosis of jaw (ONJ) related to the use of oral bisphosphonates (BPs).

Materials and Methods

Data from the National Health Insurance system of Taiwan. This cohort study included 19,399 adult osteoporosis patients received dental extraction in 2000-2010 (osteoporosis cohort) and 38,669 age and gender matched comparisons selected from dental extraction people without osteoporosis and osteonecrosis history (comparison cohort). All study subjects were followed from the date of their dental extraction (index date) to the development of ONJ and were included in the study up to 2011 or were lost to the study, whichever occurred first. Cox proportional hazard regression was used to estimate the hazard ratio and 95% confidence intervals for the two cohorts.

Results

Patients with osteoporosis had a significantly higher risk to develop ONJ than healthy persons (adjusted HR, 2.05; 95% confidence interval, 1.58–2.65). The risk of ONJ increased with the severity of osteoporosis, no matter whether patient with cancer or not. A cumulative effect of dental extraction frequency may increase the risk of ONJ.

Conclusions

We concluded that ONJ is caused by a number of factors. Osteoporosis and past dental history play the very important roles, while BPs play the synergistic effect.     

Determinants of Socioeconomic Inequalities in Traumatic Dental Injuries among Urban Indian Adolescents

Objectives

To assess socioeconomic inequalities in traumatic dental injuries (TDIs) in adolescents in New Delhi and examine the role of material, psychosocial and behavioural factors in explaining these inequalities.

Methods

We conducted a cross sectional study of 1386 adolescents aged between 12–15 years residing in three diverse areas of New Delhi. A non-invasive clinical examination was used to estimate the prevalence of TDIs, and an interviewer-administered questionnaire was used to gather relevant behavioural and socio-demographic data. Multiple logistic regression models were used to assess the association between area based socioeconomic position and TDIs.

Results

The overall prevalence of TDIs was 10.9%. Social inequalities in the prevalence of TDIs were observed across the adolescent population according to their area of residence. Socio-economic group differences in the prevalence of TDIs remained statistically significant after adjusting for demographic factors, material resources, social capital, social support and health affecting behaviours (OR 3.36, 95% CI 1.75–6.46 and OR 3.99, 95% CI 1.86–8.56 for adolescents from resettlement areas and urban slums respectively in comparison to middle class adolescents). Different psychosocial, material and socio-demographic variables did not attenuate the estimates for the relationship between area socioeconomic position and TDIs.

Conclusion

Area of residence was a strong predictor of TDIs in adolescents with a higher prevalence in more deprived areas. Social inequalities in TDIs were not explained by psychosocial and behavioural variables. Health promoting policies aimed at improving the physical environment in which adolescents reside might be instrumental in reducing the prevalence of TDIs and associated inequalities.     

In Vitro Analysis of Fibronectin-Modified Titanium Surfaces

Background

Glow discharge plasma (GDP) procedure is an effective method for grafting various proteins, including albumin, type I collagen, and fibronectin, onto a titanium surface. However, the behavior and impact of titanium (Ti) surface modification is yet to be unraveled.

Purpose

The purpose of this study is to evaluate and analyze the biological properties of fibronectin-grafted Ti surfaces treated by GDP.

Materials and Methods

Grade II Ti discs were initially cleaned and autoclaved to obtain original specimens. Subsequently, the specimens were GDP treated and grafted with fibronectin to form Ar-GDP (Argon GDP treatment only) and GDP-fib (fibronectin coating following GDP treatment) groups. Blood coagulation test and MG-63 cell culture were performed to evaluate the biological effects on the specimen.

Results

There was no significant difference between Ar-GDP and GDP-fib groups in blood compatibility analysis. While in the MTT test, cellular proliferation was benefited from the presence of fibronectin coating. The numbers of cells on Ar-GDP and GDP-fib specimens were greater than those in the original specimens after 24 h of culturing.

Conclusions

GDP treatment combined with fibronectin grafting favored MG-63 cell adhesion, migration, and proliferation on titanium surfaces, which could be attributed to the improved surface properties.     

New Design for Rapid Prototyping of Digital Master Casts for Multiple Dental Implant Restorations

Aim

This study proposes the replacement of all the physical devices used in the manufacturing of conventional prostheses through the use of digital tools, such as 3D scanners, CAD design software, 3D implants files, rapid prototyping machines or reverse engineering software, in order to develop laboratory work models from which to finish coatings for dental prostheses. Different types of dental prosthetic structures are used, which were adjusted by a non-rotatory threaded fixing system.

Method

From a digital process, the relative positions of dental implants, soft tissue and adjacent teeth of edentulous or partially edentulous patients has been captured, and a maser working model which accurately replicates data relating to the patients oral cavity has been through treatment of three-dimensional digital data.

Results

Compared with the conventional master cast, the results show a significant cost savings in attachments, as well as an increase in the quality of reproduction and accuracy of the master cast, with the consequent reduction in the number of patient consultation visits. The combination of software and hardware three-dimensional tools allows the optimization of the planning of dental implant-supported rehabilitations protocol, improving the predictability of clinical treatments and the production cost savings of master casts for restorations upon implants.     

Discordance between Prevalent Vertebral Fracture and Vertebral Strength Estimated by the Finite Element Method Based on Quantitative Computed Tomography in Patients with Type 2 Diabetes Mellitus

Background

Bone fragility is increased in patients with type 2 diabetes mellitus (T2DM), but a useful method to estimate bone fragility in T2DM patients is lacking because bone mineral density alone is not sufficient to assess the risk of fracture. This study investigated the association between prevalent vertebral fractures (VFs) and the vertebral strength index estimated by the quantitative computed tomography-based nonlinear finite element method (QCT-based nonlinear FEM) using multi-detector computed tomography (MDCT) for clinical practice use.

Research Design and Methods

A cross-sectional observational study was conducted on 54 postmenopausal women and 92 men over 50 years of age, all of whom had T2DM. The vertebral strength index was compared in patients with and without VFs confirmed by spinal radiographs. A standard FEM procedure was performed with the application of known parameters for the bone material properties obtained from nondiabetic subjects.

Results

A total of 20 women (37.0%) and 39 men (42.4%) with VFs were identified. The vertebral strength index was significantly higher in the men than in the women (P<0.01). Multiple regression analysis demonstrated that the vertebral strength index was significantly and positively correlated with the spinal bone mineral density (BMD) and inversely associated with age in both genders. There were no significant differences in the parameters, including the vertebral strength index, between patients with and without VFs. Logistic regression analysis adjusted for age, spine BMD, BMI, HbA1c, and duration of T2DM did not indicate a significant relationship between the vertebral strength index and the presence of VFs.

Conclusion

The vertebral strength index calculated by QCT-based nonlinear FEM using material property parameters obtained from nondiabetic subjects, whose risk of fracture is lower than that of T2DM patients, was not significantly associated with bone fragility in patients with T2DM. This discordance may indirectly suggest that patients with T2DM have deteriorated bone material compared with nondiabetic subjects, a potential cause of bone fragility in T2DM patients.     

Dynamic Modelling of Tooth Deformation Using Occlusal Kinematics and Finite Element Analysis

Background

Dental biomechanics based on finite element (FE) analysis is attracting enormous interest in dentistry, biology, anthropology and palaeontology. Nonetheless, several shortcomings in FE modeling exist, mainly due to unrealistic loading conditions. In this contribution we used kinematics information recorded in a virtual environment derived from occlusal contact detection between high resolution models of an upper and lower human first molar pair (M¹ and M₁, respectively) to run a non-linear dynamic FE crash colliding test.

Methodology

MicroCT image data of a modern human skull were segmented to reconstruct digital models of the antagonistic right M¹ and M₁ and the dental supporting structures. We used the Occlusal Fingerprint Analyser software to reconstruct the individual occlusal pathway trajectory during the power stroke of the chewing cycle, which was applied in a FE simulation to guide the M₁ 3D-path for the crash colliding test.

Results

FE analysis results showed that the stress pattern changes considerably during the power stroke, demonstrating that knowledge about chewing kinematics in conjunction with a morphologically detailed FE model is crucial for understanding tooth form and function under physiological conditions.

Conclusions/Significance

Results from such advanced dynamic approaches will be applicable to evaluate and avoid mechanical failure in prosthodontics/endodontic treatments, and to test material behavior for modern tooth restoration in dentistry. This approach will also allow us to improve our knowledge in chewing-related biomechanics for functional diagnosis and therapy, and it will help paleoanthropologists to illuminate dental adaptive processes and morphological modifications in human evolution.     

Reference Values of Grip Strength Measured with a Jamar Dynamometer in 1526 Adults with Intellectual Disabilities and Compared to Adults without Intellectual Disability

Aim

The aim of this study was to investigate grip strength in a large sample of people with intellectual disabilities, to establish reference values for adults with intellectual disabilities (ID) and compare it to adults without intellectual disability.

Methods

This study analysed pooled baseline data from two independent studies for all 1526 adults with ID: Special Olympics Funfitness Spain (n = 801) and the Dutch cross-sectional study ‘Healthy aging and intellectual disabilities’ (n = 725).

Results

The grip strength result of people with ID across gender and age subgroups is presented with CI95% values from higher 25.5–31.0 kg in male younger to lower 4.3–21.6 kg in female older.

Conclusion

This study is the first to present grip strength results of a large sample of people with ID from 20–90 years of age. This study provides reference values for people with ID for use in clinical practice.