Reduction of barnacle recruitment on micro‐textured surfaces: Analysis of effective topographic characteristics and evaluation of skin friction

This study investigates five designed micro‐textured surfaces and their effects on barnacle fouling and hydrodynamic drag. Three of the micro‐textures were developed in the present study and evaluated together with two commercial riblet films. All micro‐structures were arranged as longitudinal grooves with different profile depths, widths and angles of inclination. In field tests the recruitment of the barnacle Balanus improvisus on micro‐textured surfaces and smooth controls was evaluated. All micro‐textured surfaces reduced recruitment, and the most efficient texture reduced recruitment by 98%. For some micro‐textures the reduction of recruitment declined as settlement intensity increased. In a correlative analysis, the trigonometric inclination of the micro‐structures explained most of the recruitment reduction. The steepest angle of inclination caused a massive reduction in barnacle settlement. Surface micro‐structures may affect the boundary‐layer flow and the hydrodynamic drag (skin friction) of the surface. The skin friction was empirically measured in a flow channel using a sub‐set of the tested micro‐textures. The measurements of skin friction showed that the orientation of the microstructures is important, with a minimum friction when the grooves are parallel to the flow. For one of the micro‐textures the skin friction was ca 10% lower compared to a hydraulically smooth surface. It is concluded that, depending on the flow speed, micro‐textures will not significantly increase skin friction when arranged parallel to the flow, even at moderate protrusion through the viscous sub‐layer.     

Drag force and surface roughness measurements on freshwater biofouled surfaces

The detrimental effect of biofilms on skin friction for near wall flows is well known. The diatom genera Gomphonema and Tabellaria dominated the biofilm mat in the freshwater open channels of the Tarraleah Hydropower Scheme in Tasmania, Australia. A multi-faceted approach was adopted to investigate the drag penalty for biofouled 1.0 m × 0.6 m test plates which incorporated species identification, drag measurement in a recirculating water tunnel and surface characterisation using close-range photogrammetry. Increases in total drag coefficient of up to 99% were measured over clean surface values for biofouled test plates incubated under flow conditions in a hydropower canal. The effective roughness of the biofouled surfaces was found to be larger than the physical roughness; the additional energy dissipation was caused in part by the vibration of the biofilms in three-dimensions under flow conditions. The data indicate that there was a roughly linear relationship between the maximum peak-to-valley height of a biofilm and the total drag coefficient.     

Drag production mechanisms of filamentous biofilms

Abstract

Biofilms were grown on smooth acrylic surfaces for nominal incubation times of three, five, and ten weeks in a flow loop at the University of Michigan. The biofilm covered surfaces were exposed to the turbulent flow in a high-aspect ratio, fully developed channel flow facility at height-based Reynolds numbers from Re_H ≈ 5,000 to 30,000. Measurements of the pressure drop along each fouled upper surface revealed that the friction drag increased from approximately 10% to 400%. The wide range in drag penalty was linked to variations in flow speed, the average thickness of the biofilms, and the level of film coverage over each surface through scaling parameters and empirical correlations. Rigid replicas of select biofilms were produced from time-averaged laser scans collected while the biofilm was subjected to flow. These rigid biofilm replicas experienced roughly half the drag increase of their compliant counterparts with the increase in friction spanning roughly 50% to 200%.     

The influence of biofilms on skin friction drag

The contribution of biofilms to skin friction drag is not clearly defined, and as regulations continue to restrict the use of biocides in antifouling paints, they are likely to form a greater presence on ship hulls. This paper reviews the flow regime around a ship's hull, the basics of boundary layer structure, and the effects of rigid surface roughness on drag. A review of experimental studies of biofilms in turbulent shear flows at laboratory and ship-scale is made. The consensus of these studies shows that biofilms increase skin friction drag. Some measurements carried out in turbulent boundary layer flow using a two-component, laser Doppler velocimeter (LDV) are also presented. These results indicate an increase in skin friction for biofilms that is dependent on composition as well as thickness.     

Roughness effects of diatomaceous slime fouling on turbulent boundary layer hydrodynamics

Abstract

Biofilm fouling significantly impacts ship performance. Here, the impact of biofilm on boundary layer structure at a ship-relevant, low Reynolds number was investigated. Boundary layer measurements were performed over slime-fouled plates using high resolution particle image velocimetry (PIV). The velocity profile over the biofilm showed a downward shift in the log-law region (ΔU⁺), resulting in an effective roughness height (k_s) of 8.8?mm, significantly larger than the physical thickness of the biofilm (1.7?±?0.5?mm) and generating more than three times as much frictional drag as the smooth-wall. The skin-friction coefficient, C_f, of the biofilm was 9.0?×?10^?3 compared with 2.9?×?10^?3 for the smooth wall. The biofilm also enhances turbulent kinetic energy (tke) and Reynolds shear stress, which are more heterogeneous in the streamwise direction than smooth-wall flows. This suggests that biofilms increase drag due to high levels of momentum transport, likely resulting from protruding streamers and surface compliance.     

Antifouling Potential of Lubricious,Micro-engineered,PDMS Elastomers against Zoospores of the Green Fouling Alga Ulva (Enteromorpha)

The settlement and release of Ulva spores from chemically modified, micro-engineered surface topographies have been investigated using poly(dimethyl siloxane) elastomers (PDMSe) with varying additions of non-network forming poly(dimethyl siloxane) based oils. The topographic features were based on 5?μm wide pillars or ridges separated by 5, 10, or 20?μm wide channels. Pattern depths were 5 or 1.5?μm. Swimming spores showed no marked difference in settlement on smooth surfaces covered with excess PDMS oils. However, incorporation of oils significantly reduced settlement density on many of the surfaces with topographic features, in particular, the 5?μm wide and deep channels. Previous results, confirmed here, demonstrate preferences by the spores to settle in channels and against pillars with spatial dimensions of 5?μm, 10?μm and 20?μm. The combination of lubricity and pillars significantly reduced the number of attached spores compared to the control, smooth, unmodified PDMSe surfaces when exposed to turbulent flow in a flow channel. The results are discussed in relation to the energy needs for spores to adhere to various surface features and the concepts of ultrahydrophobic surfaces. A factorial, multi-level experimental design was analyzed and a 2nd order polynomial model was regressed for statistically significant effects and interactions to determine the magnitude and direction of influence on the spore density measurements between factor levels.     

An assessment of the dynamic stability of microorganisms on patterned surfaces in relation to biofouling control

Microstructure-based patterned surfaces with antifouling capabilities against a wide range of organisms are yet to be optimised. Several studies have shown that microtopographic features affect the settlement and the early stages of biofilm formation of microorganisms. It is speculated that the fluctuating stress–strain rates developed on patterned surfaces disrupt the stability of microorganisms. This study investigated the dynamic interactions of a motile bacterium (Escherichia coli) with microtopographies in relation to initial settlement. The trajectories of E. coli across a patterned surface of a microwell array within a microchannel-based flow cell system were assessed experimentally with a time-lapse imaging module. The microwell array was composed of 256 circular wells, each with diameter 10?μm, spacing 7?μm and depth 5?μm. The dynamics of E. coli over microwell-based patterned surfaces were compared with those over plain surfaces and an increased velocity of cell bodies was observed in the case of patterned surfaces. The experimental results were further verified and supported by computational fluid dynamic simulations. Finally, it was stated that the nature of solid boundaries and the associated microfluidic conditions play key roles in determining the dynamic stability of motile bacteria in the close vicinity over surfaces.     

Biological characterization of the skin of shortfin mako shark Isurus oxyrinchus and preliminary study of the hydrodynamic behaviour through computational fluid dynamics

This study characterized the morphology, density and orientation of the dermal denticles along the body of a shortfin mako shark Isurus oxyrinchus and identified the hydrodynamic parameters of its body through a computational fluid‐dynamics model. The study showed a great variability in the morphology, size, shape, orientation and density of dermal denticles along the body of I. oxyrinchus. There was a significant higher density in dorsal and ventral areas of the body and their highest angular deviations were found in the lower part of the mouth and in the areas between the pre‐caudal pit and the second dorsal and pelvic fins. A detailed three‐dimensional geometry from a scanned body of a shark was carried out to evaluate the hydrodynamic properties such as drag coefficient, lift coefficient and superficial (skin) friction coefficient of the skin together with flow velocity field, according to different roughness coefficients simulating the effect of the dermal denticles. This preliminary approach contributed to detailed information of the denticle interactions. As the height of the denticles was increased, flow velocity and the effect of lift decreased whereas drag increased. The highest peaks of skin friction coefficient were observed around the pectoral fins.     

The forces on microorganisms at surfaces in flowing water

SUMMARY.

• 1 Surfaces in flowing water are covered by boundary layers within which the velocity of flow ranges between zero at the surface and the velocity of the main stream at the limits of the boundary layer.
• 2 Many organisms are small enough to live entirely within the boundary layer and so are subjected to much smaller drag forces than if they were exposed to the main stream velocity.
• 3 The form and extent of boundary layers at different stream velocities around selected structures, representing leaves and stems, have been calculated and presented graphically.
• 4 These data provide a basis for the estimation of shear stresses on substrate surfaces and of forces exerted upon organisms of different sizes that live within the boundary layers around such surfaces, when exposed to different current velocities. Values for shear stresses on bacteria calculated in this way lie within the range of shear stresses required to detach bacteria from surfaces experimentally.

     

Ecosystem engineering by larvae of net-spinning stream caddisflies creates a habitat on the upper surface of stones for mayfly nymphs with a low resistance to flows

1. Field and laboratory experiments were conducted to examine the effect of larval retreats of the net‐spinning stream caddisfly Hydropsyche orientalis on abundances on flow exposed stone surfaces of nymphs of the mayfly Ephemerella setigera, which prefer slow flow conditions, and to determine whether the construction of retreats ameliorated the habitat and made it more suitable for E. setigera. 2. In a field experiment, artificial substrates with retreats of H. orientalis had higher E. setigera abundances than substrates lacking retreats. In addition, abundances of E. setigera nymphs increased significantly with those of H. orientalis larvae on the upper surface of boulders in streams. 3. The drift loss of E. setigera from plates, with and without retreats, was investigated along a current velocity gradient in a laboratory channel experiment. Nearly all E. setigera nymphs remained on the plates with retreats, even at the highest current velocity. In contrast, on the plates without retreats, the drift loss of E. setigera nymphs increased as the current velocity increased. 4. These results suggested that the habitat amelioration by H. orientalis retreats provided a refuge location for E. setigera nymphs and increased their abundances on stone surfaces exposed to flow forces.     

Microscale measurements reveal contrasting effects of photosynthesis and epiphytes on frictional drag on the surfaces of filamentous algae

相似文献   

Drag reduction in wave-swept macroalgae: Alternative strategies and new predictions

? Premise of the study: Intertidal macroalgae must resist extreme hydrodynamic forces imposed by crashing waves. How does frond flexibility mitigate drag, and how does flexibility affect predictions of drag and dislodgement in the field? ? Methods: We characterized flexible reconfiguration of six seaweed species in a recirculating water flume, documenting both shape change and area reduction as fronds reorient. We then used a high-speed gravity-accelerated water flume to test our ability to predict drag under waves based on extrapolations of drag recorded at slower speeds. We compared dislodgement forces to drag forces predicted from slow- and high-speed data to generate new predictions of survivorship and maximum sustainable frond size along wave-swept shores. ? Key results: Bladed algae were generally "shape changers", limiting drag by reducing drag coefficients, whereas the branched alga Calliarthron was an "area reducer", limiting drag by reducing projected area in flow. Drag predictions often underestimated actual drag measurements at high speeds, suggesting that slow-speed data may not reflect the performance of flexible seaweeds under breaking waves. Several seaweeds were predicted to dislodge at similar combinations of velocity and frond size, suggesting common scaling factors of dislodgement strength and drag. ? Conclusions: Changing shape and reducing projected area in flow are two distinct strategies employed by flexible seaweeds to resist drag. Flexible reconfiguration contributes to the uncertainty of drag extrapolation, and researchers should use caution when predicting drag and dislodgement of seaweeds in the field.     

Drag and reconfiguration of freshwater macrophytes

SUMMARY 1. Submerged freshwater macrophytes face large hydrodynamic forces in flowing waters in streams and on wave‐swept lake shores and require morphological adaptations to reduce the drag and the physical damage. This experiment studied five species of freshwater macrophytes and strap‐formed plastic leaves to test the predictions that: (i) increasing flexibility leads to greater reconfiguration and lower drag coefficients, (ii) flexible plants experience a steeper decline of drag coefficients with increasing water velocity than unflexible plants and (iii) plants mounted vertically on a horizontal substratum bend over in fast flow attaining a shielded position of low drag. 2. The results confirmed all three predictions. In fast flow, plants mounted upright on a horizontal platform gradually approached a position aligned with the flow, depending on their flexibility. In the range 8–50 cm s^?1 the deflection followed an interspecific negative linear relationship between log (tangent Φ) and velocity, where Φ represents the shoot angle normal to the horizontal level. Above 50 cm s^?1, further deflection was reduced perhaps by a combination of the elasticity and packing of shoots and the increasing lift generated by fast flow. 3. Drag coefficients of plants ranged between 0.01 and 0.1, typical of moderately to very streamlined objects. Drag coefficients declined log‐log linearly at increasing velocity, following negative slopes between ?0.67 and ?1.24 (median: ?1.0) because of reconfiguration and formation of a shielding canopy. Drag coefficients declined much less (median: ?0.55) for plants floating freely in the streaming water and which were capable of changing their shape but unable to form a shielding canopy. Drag coefficients declined even less for relatively unflexible plastic leaves (?0.30 to ?0.40), and they remained constant for stiff, bluff objects. 4. The experiments suggest that flow resistance of flexible, submerged macrophytes in natural streams may increase in direct proportion to water velocity because they form a shielding submerged canopy, and high water stages at peak flow may result in greater proportions of the water passing unimpeded above the canopy. In contrast, stiff amphibious and emergent reed plants should experience an increase of flow resistance with at least the square of velocity as reconfiguration is small and former aerial plant surfaces come into contact with the streaming water at higher water stages. Field experiments to test these predictions are urgently needed.     

Streamlining of plant patches in streams

1. Plants in shallow streams often grow in well‐defined monospecific patches experiencing a predictable unidirectional flow, though of temporally variable velocity. During maximum patch development in summer we studied: (i) the shape and streamlining of 59 patches of Callitriche cophocarpa, (ii) allometric relationships between canopy size and sediment area colonized by roots (root area) and (iii) fine‐scale flow gradients for a representative patch exposed to a range of velocities to evaluate relationships between patch shape and physical impact. 2. Canopy and root area viewed from above were elongated and streamlined in the flow direction, while uniform vegetative growth in all directions from a single colonizing shoot would have generated a circular form. Canopies were slightly wider in the upstream part than in the gradually tapering part downstream and the maximum height to length ratio averaged 0.25. The canopy and root area of the patches were more elongate and slender in sites with shallow water, where currents accelerate alongside patches and restrict lateral expansion, compared to deeper sites where currents can pass above the canopy. Similarly, the frontal area relative to planform area or root area was significantly lower in shallow water . Canopy shape and indices of streamlining did not change significantly with approach velocity (0.02–0.40 m s^?1), either because canopy shape is not sensitive to approach velocity or summer velocities were too low to induce such changes. 3. Sediment elevation within patches (avg. 4.1 cm) increased significantly with patch length, but did not differ between unstable sand or more stable coarse sediment for the same patch length. Shape of canopy and root area did not change significantly with sediment type. 4. Pressure drag on the canopy as a whole is probably reduced by its rounded front, restricted height and overall slender form with a low frontal area, while the downstream overhanging canopy increases drag compared to an ideal streamlined object. Across a 100‐fold range of root areas from 0.01 to 1 m², the frontal area of the canopy increased 29 times, planform area increased 38 times and volume increased 76 times, suggesting a trade‐off between physical impact of flow, light interception and anchoring strength. 5. The canopy was compressed at high approach velocities, with low current velocity within the canopy while steep velocity gradients developed across the exposed outer surfaces as the diverted flow accelerated. Because drag processes are additive, and exist at different spatial scales and Reynolds numbers on the surface and inside of plant canopies, direct measurements on entire canopies under controlled conditions are needed to test the functional importance of their shape, size and porosity to flow.     

Biofilm formation in laminar flow usingPseudomonas fluorescens EX101

The relationship between biofilm formation and Reynolds number in laminar flow has been investigated usingPseudomonas fluorescens EX101. It was shown using a Modified Robbins Device that in laminar flow, numbers of viable cells in a developed biofilm increased with Reynolds number (Re 2, 17 and 51.5), as would be expected in a system where molecular transport to the wall is limited by diffusion. By monitoring fluorescent beads in a flowcell with a scanning confocal laser microscope at similar low Reynolds numbers, the velocity profile close to the solid surface was determined. It was shown that the presence of a thin bacterial film (up to 12 m) displaced the flow profile away from the wall by a distance equivalent to the film thickness. Total cell counts from the Modified Robbins Device samples were not significantly different at the different flow rates but were higher than viable counts. Interruption of the flow had no significant effect on colonisation by the bacteria through the Modified Robbins Device in the first few hours. However, viable numbers were reduced when the flow was stopped at 7 h after initial colonisation.     

Polyphenic wax production in Abacarus hystrix(Acari: Eriophyidae), and implications for migratory fitness

Abstract. . Wax production in the grass-feeding eriophyid Abacarus hystrix (Nalepa) is seasonally variable; enlarged lateral and dorsal bands of wax filaments develop in adults of summer generations. Wax filaments increase the total surface area of summer-generation mites, without a concomitant increase in cuticular surface-to-volume ratio. Genetic and environmental interactions in changes in the rate of wax production were examined. High temperatures, but not changes in photoperiod, were found to stimulate increased rates of wax production. The degree of wax filamentation was independent of the genetic origin of mites, hence filaments are polyphenic, rather than polymorphic, in origin. The role of wax filaments in the regulation of water-loss and in drag maximization were experimentally investigated. The relative survival of waxed and unwaxed mites was compared at various temperature and humidity combinations, and the influence of wax filaments on surface drag was assessed by comparing the slopes of regression lines of cuticular surface area relative to terminal velocity of waxed and unwaxed mites. Significantly greater survival times in waxed compared to unwaxed mites at low relative humidities suggest mat wax filaments have a function in the regulation of water-loss. Significantly lower mean terminal velocities in waxed mites indicated that total drag relative to cuticular surface area was greater in waxed than unwaxed mites, probably as a result of increased skin friction generated by wax filaments. The increased non-cuticular surface area created by wax filaments may be advantageous during summer-migrations of A.hystrix by increasing wind shear stress on the mites at the leaf margin, enhancing buoyancy while air-borne and reducing the rate of desiccation-induced mortality.     

Motion of cells sedimenting on a solid surface in a laminar shear flow.

Cell adhesion often occurs under dynamic conditions, as in flowing blood. A quantitative understanding of this process requires accurate knowledge of the topographical relationships between the cell membrane and potentially adhesive surfaces. This report describes an experimental study made on both the translational and rotational velocities of leukocytes sedimenting of a flat surface under laminar shear flow. The main conclusions are as follows: (a) Cells move close to the wall with constant velocity for several tens of seconds. (b) The numerical values of translational and rotational velocities are inconsistent with Goldman's model of a neutrally buoyant sphere in a laminar shear flow, unless a drag force corresponding to contact friction between cells and the chamber floor is added. The phenomenological friction coefficient was 7.4 millinewton.s/m. (c) Using a modified Goldman's theory, the width of the gap separating cells (6 microns radius) from the chamber floor was estimated at 1.4 micron. (d) It is shown that a high value of the cell-to-substrate gap may be accounted for by the presence of cell surface protrusions of a few micrometer length, in accordance with electron microscope observations performed on the same cell population. (e) In association with previously reported data (Tissot, O., C. Foa, C. Capo, H. Brailly, M. Delaage, and P. Bongrand. 1991. Biocolloids and Biosurfaces. In press), these results are consistent with the possibility that cell-substrate attachment be initiated by the formation of a single molecular bond, which might be considered as the rate limiting step.     

Bionic Research on Fish Scales for Drag Reduction

To reduce friction drag with bionic method in a more feasible way,the surface microstructure of fish scales was analyzed attempting to reveal the biologic features responding to skin friction drag reduction.Then comparable bionic surface mimicking fish scales was fabricated through coating technology for drag reduction.The paint mixture was coated on a substrate through a self-developed spray-painting apparatus.The bionic surface with micron-scale caves formed spontaneously due to the interfacial convection and deformation driven by interfacial tension gradient in the presence of solvent evaporation.Comparative experiments between bionic surface and smooth surface were performed in a water tunnel to evaluate the effect of bionic surface on drag reduction,and visible drag reduction efficiency was obtained.Numerical simulation results show that gas phase develops in solid-liquid interface of bionic surface with the effect of surface topography and partially replaces the solid-liquid shear force with gas-liquid shear force,hence reducing the skin friction drag effectively.Therefore,with remarkable drag reduction performance and simple fabrication technology,the proposed drag reduction technique shows the promise for practical applications.     

Attachment strength of an adhesive nuisance mussel,limnoperna fortunei,against water flow

The attachment strength of the freshwater mussel Limnoperna fortunei against water flow was studied. Newton's expression successfully described the hydrodynamic drag force acting on the mussel with a drag coefficient value of 1.03. The drag‐resistant force (defined as hydrodynamic drag force at mussel detachment) was smaller than the detachment force measured using a tensile load test. A fairly good correlation was obtained between the drag‐resistant force and the number of secreted threads. The drag‐resistant force divided by the number of threads increased with shell size, suggesting that byssal thread strength increased with mussel growth. For the mussel specimens obtained from a water transmission pipe, thread width increased with shell size. However, thread width was not dependent on current velocity. There was no correlation between the number of secreted threads and shell length, which indicated that the number of secreted threads did not change with mussel size. Therefore, the water velocity needed to detach mussels increases with shell size of the mussel when the number of secreted threads is constant. The increases in the water velocity to detach mussels with larger shells suggests that the mussel becomes more resistant to water flow as it grows. It is estimated that a flow velocity of around lms^‐1 is critical for attachment/detachment of a juvenile mussel with a shell length of a few millimeters and one hundred byssal threads.     

Daily tracking of the locomotion of the nudibranch Tritonia tetraquetra (Pallas 1788 = Tritonia diomedea Bergh 1894) in nature and the influence of water flow on orientation,crawling, and drag

We observed orientation and locomotion of the nudibranch Tritonia tetraquetra in its natural habitat using SCUBA over many sequential days, in three different months. The slugs oriented significantly headfirst to tidal currents. Nevertheless, the direction of locomotion of the slugs over hours was not usually correlated with tidal flow direction (i.e. not indicative of consistent rheotaxis). We did not find evidence of consistent body axis orientation to the geomagnetic field, but the direction of locomotion of some groups of slugs over hours was significantly correlated with geomagnetic direction. Independent of direction, each slug changed position by an average of ～2?m during a single tidal phase (～6?h), and changed position by an average of ～4?m over a full tidal cycle (～25?h). Orientation to flow reduced drag, and reduced the probability that a slug will be dislodged from the soft bottom, in laboratory experiments. Slugs deprived of olfactory and flow cues exhibit a search-like pattern of multiple and frequent turns.