Size‐Dependent Charge Transfer in Blends of PbS Quantum Dots with a Low‐Gap Silicon‐Bridged Copolymer

The photophysics of bulk heterojunctions of a high‐performance, low‐gap silicon‐bridged dithiophene polymer with oleic acid capped PbS quantum dots (QDs) are studied to assess the material potential for light harvesting in the visible‐ and IR‐light ranges. By employing a wide range of nanocrystal sizes, systematic dependences of electron and hole transfer on quantum‐dot size are established for the first time on a low‐gap polymer–dot system. The studied system exhibits type II band offsets for dot sizes up to ca. 4 nm, whch allow fast hole transfer from the quantum dots to the polymer that competes favorably with the intrinsic QD recombination. Electron transfer from the polymer is also observed although it is less competitive with the fast polymer exciton recombination for most QD sizes studied. The incorporation of a fullerene derivative provides efficient electron‐quenching sites that improve interfacial polymer‐exciton dissociation in ternary polymer–fullerene–QD blends. The study indicates that programmable band offsets that allow both electron and hole extraction can be produced for efficient light harvesting based on this low‐gap polymer‐PbS QD composite.     

Polymer Blend Solar Cells Based on a High‐Mobility Naphthalenediimide‐Based Polymer Acceptor: Device Physics,Photophysics and Morphology

A high electron mobility polymer, poly{[N,N’‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5’‐(2,2’‐bithiophene) (P(NDI2OD‐T2)) is investigated for use as an electron acceptor in all‐polymer blends. Despite the high bulk electron mobility, near‐infrared absorption band and compatible energy levels, bulk heterojunction devices fabricated with poly(3‐hexylthiophene) (P3HT) as the electron donor exhibit power conversion efficiencies of only 0.2%. In order to understand this disappointing photovoltaic performance, systematic investigations of the photophysics, device physics and morphology of this system are performed. Ultra‐fast transient absorption spectroscopy reveals a two‐stage decay process with an initial rapid loss of photoinduced polarons, followed by a second slower decay. This second slower decay is similar to what is observed for efficient P3HT:PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) blends, however the initial fast decay that is absent in P3HT:PCBM blends suggests rapid, geminate recombination of charge pairs shortly after charge transfer. X‐ray microscopy reveals coarse phase separation of P3HT:P(NDI2OD‐T2) blends with domains of size 0.2 to 1 micrometer. P3HT photoluminescence, however, is still found to be efficiently quenched indicating intermixing within these mesoscale domains. This hierarchy of phase separation is consistent with the transient absorption, whereby localized confinement of charges on isolated chains in the matrix of the other polymer hinders the separation of interfacial electron‐hole pairs. These results indicate that local, interfacial processes are the key factor determining the overall efficiency of this system and highlight the need for improved morphological control in order for the potential benefit of high‐mobility electron accepting polymers to be realized.     

Selective Dye Loading at the Heterojunction in Polymer/Fullerene Solar Cells

Selective dye loading at the polymer/fullerene interface was studied for ternary blend bulk heterojunction solar cells, consisting of regioregular poly(3‐hexylthiophene) (RR‐P3HT), a fullerene derivative (PCBM), and a silicon phthalocyanine derivative (SiPc) as a light‐harvesting dye. The photocurrent density and power conversion efficiency of the ternary blend solar cells were most improved by loading SiPc with a content of 4.8 wt%. The absorption and surface energy measurements suggested that SiPc is located in the disordered P3HT domains at the RR‐P3HT/PCBM interface rather than in the PCBM and crystal P3HT domains. From the peak wavelength of SiPc absorption, the local concentration of SiPc ([SiPc]_Local) was estimated for the RR‐P3HT:PCBM:SiPc ternary blends. Even for amorphous films of regiorandom P3HT (RRa‐P3HT) blended with PCBM and SiPc, [SiPc]_Local was higher than the original content, suggesting dye segregation into the RRa‐P3HT/PCBM interface. For RR‐P3HT:PCBM:SiPc blends, [SiPc]_Local increased with the increase in the P3HT crystallinity. Such interfacial segregation of dye molecules in ternary blend films can be rationally explained in terms of the surface energy of each component and the crystallization of P3HT being enhanced by annealing. Notably, the solvent annealing effectively segregated dye molecules into the interface without the formation of PCBM clusters.     

Charge Photogeneration in Organic Photovoltaics: Role of Hot versus Cold Charge‐Transfer Excitons

The role of excess excitation energy on long‐range charge separation in organic donor/acceptor bulk heterojunctions (BHJs) continues to be unclear. While ultrafast spectroscopy results argue for efficient charge separation through high‐energy charge‐transfer (CT) states within the first picosecond (ps) of excitation, charge collection measurements suggest excess photon energy does not increase the current density in BHJ devices. Here, the population dynamics of charge‐separated polarons upon excitation of high‐energy polymer states and low‐energy interfacial CT states in two polymer/fullerene blends from ps to nanosecond time scales are studied. It is observed that the charge‐separation dynamics do not show significant dependence on excitation energy. These results confirm that excess exciton energy is not necessary for the effective generation of charges.     

Spontaneous Charge Transfer and Dipole Formation at the Interface Between P3HT and PCBM

In the pursuit of developing new materials for more efficient bulk‐heterojunction solar cells, the blend poly (3‐hexylthiophene):[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) serves as an important model system. The success of the P3HT:PCBM blend comes from efficient charge generation and transport with low recombination. There is not, however, a good microscopic picture of what causes these, hindering the development of new material systems. In this report UV photoelectron spectroscopy measurements on both regiorandom‐ (rra) and regioregular‐ (rr) P3HT are presented, and the results are interpreted using the Integer Charge Transfer model. The results suggest that spontaneous charge transfer from P3HT to PCBM occurs after heat treatment of P3HT:PCBM blends. The resulting formation of an interfacial dipole creates an extra barrier at the interface explaining the reduced (non‐)geminate recombination with increased charge generation in heat treated rr‐P3HT:PCBM blends. Extensive photoinduced absorption measurements using both above‐ and below‐bandgap excitation light are presented, in good agreement with the suggested dipole formation.     

Simultaneous Open‐Circuit Voltage Enhancement and Short‐Circuit Current Loss in Polymer: Fullerene Solar Cells Correlated by Reduced Quantum Efficiency for Photoinduced Electron Transfer

The limits of maximizing the open‐circuit voltage V_oc in solar cells based on poly[2,7‐(9,9‐didecylfluorene)‐alt‐5,5‐(4,7‐di‐2‐thienyl‐2,1,3‐benzothiadiazole)] (PF10TBT) as a donor using different fullerene derivatives as acceptor are investigated. Bulk heterojunction solar cells with PF10TBT and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) give a V_oc over 1 V and a power conversion efficiency of 4.2%. Devices in which PF10TBT is blended with fullerene bisadduct derivatives give an even higher V_oc, but also a strong decrease in short circuit current (J_sc). The higher V_oc is attributed to the higher LUMO of the acceptors in comparison to PCBM. By investigating the photophysics of PF10TBT:fullerene blends using near‐IR photo‐ and electroluminescence, time‐resolved photoluminescence, and photoinduced absorption we find that the charge transfer (CT) state is not formed efficiently when using fullerene bisadducts. Hence, engineering acceptor materials with a LUMO level that is as high as possible can increase V_oc, but will only provide a higher power conversion efficiency, when the quantum efficiency for charge transfer is preserved. To quantify this, we determine the CT energy (E_CT) and optical band gap (E_g), defined as the lowest first singlet state energy E_S1 of either the donor or acceptor, for each of the blends and find a clear correlation between the free energy for photoinduced electron transfer and J_sc. We find that E_g ? qV_oc > 0.6 eV is a simple, but general criterion for efficient charge generation in donor‐acceptor blends.     

Synthesis of near‐infrared‐emitting CdTeSe and CdZnTeSe quantum dots

We exploited the synthesis of near‐infrared (NIR) emitting ternary‐alloyed CdTeSe and quaternary‐alloyed CdZnTeSe quantum dots (QDs) with rod and tetrapod morphologies, which have tunable emission in the NIR electromagnetic spectrum. The morphologies of the QDs depended strongly on their growth kinetics, probably due to the coordinating ligands used in the preparation. Using oleic acid, stearic acid and hexadecylamine as ligands and keeping the same reaction parameters, QDs with tetrapod and rod morphologies were created. Not only had the capping ligands influenced the morphologies of QDs, but also they influenced the optical properties of QDs. The molar ratios of Cd/Zn and Te/Se upon preparation were adjusted for investigating the effect of composition on the properties of resulting QDs. By varying the composition of QDs, the photoluminescence (PL) wavelength of QDs was tuned from 650 nm to 800 nm. To enhance PL efficiency and stability, QDs were coated with a CdZnS shell. As NIR PL has numerous advantages in biological imaging detection, these QDs hold great potential for application. Copyright © 2012 John Wiley & Sons, Ltd.     

Nanofiber‐Based Bulk‐Heterojunction Organic Solar Cells Using Coaxial Electrospinning

Nanofibers consisting of the bulk heterojunction organic photovoltaic (BHJ–OPV) electron donor–electron acceptor pair poly(3‐hexylthiophene):phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) are produced through a coaxial electrospinning process. While P3HT:PCBM blends are not directly electrospinnable, P3HT:PCBM‐containing fibers are produced in a coaxial fashion by utilizing polycaprolactone (PCL) as an electrospinnable sheath material. Pure P3HT:PCBM fibers are easily obtained after electrospinning by selectively removing the PCL sheath with cyclopentanone (average diameter 120 ± 30 nm). These fibers are then incorporated into the active layer of a BHJ–OPV device, which results in improved short‐circuit current densities, fill factors, and power‐conversion efficiencies (PCE) as compared to thin‐film devices of identical chemical composition. The best‐performing fiber‐based devices exhibit a PCE of 4.0%, while the best thin‐film devices have a PCE of 3.2%. This increase in device performance is attributed to the increased in‐plane alignment of P3HT polymer chains on the nanoscale, caused by the electrospun fibers, which leads to increased optical absorption and subsequent exciton generation. This methodology for improving device performance of BHJ–OPVs could also be implemented for other electron donor–electron acceptor systems, as nanofiber formation is largely independent of the PV material.     

Tail State‐Assisted Charge Injection and Recombination at the Electron‐Collecting Interface of P3HT:PCBM Bulk‐Heterojunction Polymer Solar Cells

The systematic insertion of thin films of P3HT and PCBM at the electron‐ and hole‐collecting interfaces, respectively, in bulk‐heterojunction polymer solar cells results in different extents of reduction in device characteristics, with the insertion of P3HT at the electron‐collecting interface being less disruptive to the output currents compared to the insertion of PCBM at the hole‐collecting interface. This asymmetry is attributed to differences in the tail state‐assisted charge injection and recombination at the active layer‐electrode interfaces. P3HT exhibits a higher density of tail states compared to PCBM; holes in these tail states can thus easily recombine with electrons at the electron‐collection interface during device operation. This process is subsequently compensated by the injection of holes from the cathode into these tail states, which collectively enables net current flow through the polymer solar cell. The study presented herein thus provides a plausible explanation for why preferential segregation of P3HT to the cathode interface is inconsequential to device characteristics in P3HT:PCBM bulk‐heterojunction solar cells.     

Domain Compositions and Fullerene Aggregation Govern Charge Photogeneration in Polymer/Fullerene Solar Cells

The complex microstructure of organic semiconductor mixtures continues to obscure the connection between the active layer morphology and photovoltaic device performance. For example, the ubiquitous presence of mixed phases in the active layer of polymer/fullerene solar cells creates multiple morphologically distinct interfaces which are capable of exciton dissociation or charge recombination. Here, it is shown that domain compositions and fullerene aggregation can strongly modulate charge photogeneration at ultrafast timescales through studies of a model system, mixtures of a low band‐gap polymer, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]germole)‐2,6‐diyl‐alt‐(2,1,3‐benzothia‐diazole)‐4,7‐diyl], and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester. Structural characterization using energy‐filtered transmission electron microscopy (EFTEM) and resonant soft X‐ray scattering shows similar microstructures even with changes in the overall film composition. Composition maps generated from EFTEM, however, demonstrate that compositions of mixed domains vary significantly with overall film composition. Furthermore, the amount of polymer in the mixed domains is inversely correlated with device performance. Photoinduced absorption studies using ultrafast infrared spectroscopy demonstrate that polaron concentrations are highest when mixed domains contain the least polymer. Grazing‐incidence X‐ray scattering results show that larger fullerene coherence lengths are correlated to higher polaron yields. Thus, the purity of the mixed domains is critical for efficient charge photogeneration because purity modulates fullerene aggregation and electron delocalization.     

Intra‐Molecular Donor–Acceptor Interaction Effects on Charge Dissociation,Charge Transport,and Charge Collection in Bulk‐Heterojunction Organic Solar Cells

This article reports experimental studies on internal charge dissociation, transport, and collection by using magnetic field effects of photocurrent (MFE_PC) and light‐assisted dielectric response (LADR) in highly‐efficient organic solar cells based on photovoltaic polymer PTB2 and PTB4 with intra‐molecular “donor–acceptor” interaction. The MFE_PC at low‐field (< 150 mT) indicates that intra‐molecular “donor‐acceptor” interaction generates charge dissociation in un‐doped PTB2 and PTB4 films, which is similar to that in lightly doped P3HT (Poly(3‐hexylthiophene)) with 5 wt% PCBM (1‐(3‐methyloxycarbonyl)‐propyl‐1‐phenyl (6,6) C₆₁). After PTB2 and PTB4 are mixed with PCBM to form bulk‐heterojunctions, the MFE_PC at high‐field (> 150 mT) reveals that the charge‐transfer complexes formed at PTB2:PCBM and PTB4:PCBM interfaces have much lower binding energies due to stronger electron‐withdrawing abilities, as compared to the P3HT:PCBM device, towards the generation of photocurrent. Furthermore, the light‐assisted dielectric response: LADR indicates that the PTB2:PCBM and PTB4:PCBM solar cells exhibit larger capacitances relative to P3HT:PCBM device under photoexcitation. This reflects that the PTB2:PCBM and PTB4:PCBM bulk heterojunctions have more effective charge transport and collection than the P3HT:PCBM counterpart. As a result, our experimental results indicate that intra‐molecular “donor‐acceptor” interaction plays an important role to enhance charge dissociation, transport, and collection in bulk‐heterojunction organic solar cells.     

Identifying the Nature of Charge Recombination in Organic Solar Cells from Charge‐Transfer State Electroluminescence

Charge‐transfer (CT) state electroluminescence is investigated in several polymer:fullerene bulk heterojunction solar cells. The ideality factor of the electroluminescence reveals that the CT emission in polymer:fullerene solar cells originates from free‐carrier bimolecular recombination at the donor‐acceptor interface, rather than a charge‐trap‐mediated process. The fingerprint of the presence of nonradiative trap‐assisted recombination, a voltage‐dependent CT electroluminescence quantum efficiency, is only observed for the P3HT:PCBM system, which is explained by a reduction of the competing bimolecular recombination rate. These results are in agreement with measurements of the illumination‐intensity dependence of the open‐circuit voltage.     

Influence of Phonon Scattering on Exciton and Charge Diffusion in Polymer‐Fullerene Solar Cells

Thermally activated transport and phonon scattering in P3HT:PCBM (poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenylC61‐butyric acid methyl ester) bulk heterojunction (BHJ) organic solar cells is studied via temperature‐dependent external‐quantum‐efficiency (EQE) spectroscopy. The hopping barriers for combined exciton and charge transport are balanced for the individual blended materials in a sample, which possesses a blending ratio and a morphology that give rise to a maximal power‐conversion efficiency. Increasing the PCBM weight fraction leads to a reduction of exciton hopping barriers in PCBM, while for P3HT exciton hopping barriers remain constant. This reduction of PCBM exciton hopping barriers is attributed to a higher PCBM crystallinity in the PCBM‐rich solar cell as compared to the BHJ with the optimized blending ratio. The morphology‐dependent difference in exciton hopping activation energies between P3HT and PCBM is attributed to a higher impact of phonon scattering in P3HT than in PCBM, as concluded from the much stronger decrease of P3HT‐related temperature‐dependent external quantum efficiencies above room temperature in the PCBM‐rich BHJ solar cell. All EQE data of P3HT:PCBM‐based BHJ solar cells is modeled consistently over a broad temperature range by a simple analytical expression involving temperature activation and phonon scattering, without the need to distinguish two separate hopping regimes.     

Local Intermolecular Order Controls Photoinduced Charge Separation at Donor/Acceptor Interfaces in Organic Semiconductors

How free charge is generated at organic donor–acceptor interfaces is an important question, as the binding energy of the lowest energy (localized) charge transfer states should be too high for the electron and hole to escape each other. Recently, it has been proposed that delocalization of the electronic states participating in charge transfer is crucial, and aggregated or otherwise locally ordered structures of the donor or the acceptor are the precondition for this electronic characteristic. The effect of intermolecular aggregation of both the polymer donor and fullerene acceptor on charge separation is studied. In the first case, the dilute electron acceptor triethylsilylhydroxy‐1,4,8,11,15,18,22,25‐octabutoxyphthalocyaninatosilicon(IV) (SiPc) is used to eliminate the influence of acceptor aggregation, and control polymer order through side‐chain regioregularity, comparing charge generation in 96% regioregular (RR‐) poly(3‐hexylthiophene) (P3HT) with its regiorandom (RRa‐) counterpart. In the second case, ordered phases in the polymer are eliminated by using RRa‐P3HT, and phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) is used as the acceptor, varying its concentration to control aggregation. Time‐resolved microwave conductivity, time‐resolved photoluminescence, and transient absorption spectroscopy measurements show that while ultrafast charge transfer occurs in all samples, long‐lived charge carriers are only produced in films with intermolecular aggregates of either RR‐P3HT or PC₆₁BM, and that polymer aggregates are just as effective in this regard as those of fullerenes.     

Improving the Performance and Stability of Inverted Planar Flexible Perovskite Solar Cells Employing a Novel NDI‐Based Polymer as the Electron Transport Layer

A new naphthalene diimide (NDI)‐based polymer with strong electron withdrawing dicyanothiophene (P(NDI2DT‐TTCN)) is developed as the electron transport layer (ETL) in place of the fullerene‐based ETL in inverted perovskite solar cells (Pero‐SCs). A combination of characterization techniques, including atomic force microscopy, scanning electron microscopy, grazing‐incidence wide‐angle X‐ray scattering, near‐edge X‐ray absorption fine‐structure spectroscopy, space‐charge‐limited current, electrochemical impedance spectroscopy, photoluminescence (PL), and time‐resolved PL decay, is used to demonstrate the interface phenomena between perovskite and P(NDI2DT‐TTCN) or [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). It is found that P(NDI2DT‐TTCN) not only improves the electron extraction ability but also prevents ambient condition interference by forming a hydrophobic ETL surface. In addition, P(NDI2DT‐TTCN) has excellent mechanical stability compared to PCBM in flexible Pero‐SCs. With these improved functionalities, the performance of devices based on P(NDI2DT‐TTCN) significantly outperform those based on PCBM from 14.3 to 17.0%, which is the highest photovoltaic performance with negligible hysteresis in the field of polymeric ETLs.     

Morphology Related Photodegradation of Low‐Band‐Gap Polymer Blends

The morphology related photodegradation of low band‐gap polymer blends is investigated using optical microscopy and scanning probe microscopy. Poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene)‐alt‐4,7(2,1,3‐benzothiadiazole)] (C‐PCPDTBT):[6,6]‐phenyl C61‐butyric acid methyl ester (PCBM) blend films without and with ODT, as well as poly[(4,40‐bis(2‐ethylhexyl)dithieno[3,2‐b:20,30‐d]silole)‐2,6‐diylalt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (Si‐PCPDTBT):PCBM blend films exposed to a focused 632.8 nm laser under ambient condition with and without inert gas protection are studied. The photodegradation of the polymer starts in the vicinity of the PCBM molecules (first sphere degradation), which effectively blocks the electron transfer processes. Stern‐Volmer type kinetics are observed in the C‐PCPDTBT:PCBM blend with ODT, which indicates that only a small number of photo‐oxidized monomer units act as quenchers of the C‐PCPDTBT polymer luminescence. Furthermore, in addition to the permanent damage of the polymer molecules, as witnessed from their Raman intensity decrease, the polymer photoluminescence demonstrates partial reversible recovery when inert gas protection is resumed, indicating the involvement of temporary polymer/O₂‐charge transfer complexes in the photodegradation process.     

Comparison of the Morphology Development of Polymer–Fullerene and Polymer–Polymer Solar Cells during Solution‐Shearing Blade Coating

In this work, the detailed morphology studies of polymer poly(3‐hexylthiophene‐2,5‐diyl) (P3HT):fullerene(PCBM) and polymer(P3HT):polymer naphthalene diimide thiophene (PNDIT) solar cell are presented to understand the challenge for getting high performance all‐polymer solar cells. The in situ X‐ray scattering and optical interferometry and ex situ hard and soft X‐ray scattering and imaging techniques are used to characterize the bulk heterojunction (BHJ) ink during drying and in dried state. The crystallization of P3HT polymers in P3HT:PCBM bulk heterojunction shows very different behavior compared to that of P3HT:PNDIT BHJ due to different mobilities of P3HT in the donor:acceptor glass. Supplemented by the ex situ grazing incidence X‐ray diffraction and soft X‐ray scattering, PNDIT has a lower tendency to form a mixed phase with P3HT than PCBM, which may be the key to inhibit the donor polymer crystallization process, thus creating preferred small phase separation between the donor and acceptor polymer.     

Near‐Infrared,Heavy Metal‐Free Colloidal “Giant” Core/Shell Quantum Dots

“Giant” core/shell quantum dots (g‐QDs) are a promising class of materials for future optoelectronic technologies due to their superior chemical‐ and photostability compared to bare QDs and core/thin shell QDs. However, inadequate light absorption in the visible and near‐infrared (NIR) region and frequent use of toxic heavy metals (e.g., Cd and Pb) are still major challenges for most g‐QDs (e.g., CdSe/CdS) synthesized to date. The synthesis of NIR, heavy metal‐free, Zn‐treated spherical CuInSe₂/CuInS₂ g‐QDs is reported using the sequential cation exchange method. These g‐QDs exhibit tunable NIR optical absorption and photoluminescence (PL) properties. Transient fluorescence spectroscopy shows prolonged lifetime with increasing shell thickness, indicating the formation of quasi type‐II band alignment, which is further confirmed by simulations. As a proof‐of‐concept, as‐synthesized g‐QDs are used to sensitize TiO₂ as a photoanode in a photoelectrochemical (PEC) cell, demonstrating an efficient and stable PEC system. These results pave the way toward synthesizing NIR heavy metal‐free g‐QDs, which are very promising components of future optoelectronic technologies.     

Suppressing Energy Loss due to Triplet Exciton Formation in Organic Solar Cells: The Role of Chemical Structures and Molecular Packing

In the most efficient solar cells based on blends of a conjugated polymer (electron donor) and a fullerene derivative (electron acceptor),ultrafast formation of charge‐transfer (CT) electronic states at the donor‐acceptor interfaces and efficient separation of these CT states into free charges, lead to internal quantum efficiencies near 100%. However, there occur substantial energy losses due to the non‐radiative recombinations of the charges, mediated by the loweset‐energy (singlet and triplet) CT states; for example, such recombinations can lead to the formation of triplet excited electronic states on the polymer chains, which do not generate free charges. This issue remains a major factor limiting the power conversion efficiencies (PCE) of these devices. The recombination rates are, however, difficult to quantify experimentally. To shed light on these issues, here, an integrated multi‐scale theoretical approach that combines molecular dynamics simulations with quantum chemistry calculations is employed in order to establish the relationships among chemical structures, molecular packing, and non‐radiative recombination losses mediated by the lowest‐energy charge‐transfer states.     

Near Infrared,Highly Efficient Luminescent Solar Concentrators

The fabrication of a low reabsorption emission loss, high efficient luminescent solar concentrator (LSC) is demonstrated by embedding near infrared (NIR) core/shell quantum dots (QDs) in a polymer matrix. An engineered Stokes shift in NIR core/shell PbS/CdS QDs is achieved via a cation exchange approach by varying the core size and shell thickness through the refined reaction parameters such as reaction time, temperature, precursor molar ratio, etc. The as‐synthesized core/shell QDs with high quantum yield (QY) and excellent chemical/photostability exhibit a large Stokes shift with respect to the bare PbS QDs due to the strong core‐to‐shell electrons leakage. The large‐area planar LSC based on core/shell QDs exhibits the highest value (6.1% with a geometric factor of 10) for optical efficiency compared to the bare NIR QD‐based LSCs and other reported NIR QD‐based LSCs. The suppression of emission loss and the broad absorption of PbS/CdS QDs offer a promising pathway to integrate LSCs and photovoltaic devices with good spectral matching, indicating that the proposed core/shell QDs are strong candidates for fabricating high efficiency semi‐transparent large‐area LSCs.