Comparison of the Morphology Development of Polymer–Fullerene and Polymer–Polymer Solar Cells during Solution‐Shearing Blade Coating

In this work, the detailed morphology studies of polymer poly(3‐hexylthiophene‐2,5‐diyl) (P3HT):fullerene(PCBM) and polymer(P3HT):polymer naphthalene diimide thiophene (PNDIT) solar cell are presented to understand the challenge for getting high performance all‐polymer solar cells. The in situ X‐ray scattering and optical interferometry and ex situ hard and soft X‐ray scattering and imaging techniques are used to characterize the bulk heterojunction (BHJ) ink during drying and in dried state. The crystallization of P3HT polymers in P3HT:PCBM bulk heterojunction shows very different behavior compared to that of P3HT:PNDIT BHJ due to different mobilities of P3HT in the donor:acceptor glass. Supplemented by the ex situ grazing incidence X‐ray diffraction and soft X‐ray scattering, PNDIT has a lower tendency to form a mixed phase with P3HT than PCBM, which may be the key to inhibit the donor polymer crystallization process, thus creating preferred small phase separation between the donor and acceptor polymer.     

Influence of Phonon Scattering on Exciton and Charge Diffusion in Polymer‐Fullerene Solar Cells

Thermally activated transport and phonon scattering in P3HT:PCBM (poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenylC61‐butyric acid methyl ester) bulk heterojunction (BHJ) organic solar cells is studied via temperature‐dependent external‐quantum‐efficiency (EQE) spectroscopy. The hopping barriers for combined exciton and charge transport are balanced for the individual blended materials in a sample, which possesses a blending ratio and a morphology that give rise to a maximal power‐conversion efficiency. Increasing the PCBM weight fraction leads to a reduction of exciton hopping barriers in PCBM, while for P3HT exciton hopping barriers remain constant. This reduction of PCBM exciton hopping barriers is attributed to a higher PCBM crystallinity in the PCBM‐rich solar cell as compared to the BHJ with the optimized blending ratio. The morphology‐dependent difference in exciton hopping activation energies between P3HT and PCBM is attributed to a higher impact of phonon scattering in P3HT than in PCBM, as concluded from the much stronger decrease of P3HT‐related temperature‐dependent external quantum efficiencies above room temperature in the PCBM‐rich BHJ solar cell. All EQE data of P3HT:PCBM‐based BHJ solar cells is modeled consistently over a broad temperature range by a simple analytical expression involving temperature activation and phonon scattering, without the need to distinguish two separate hopping regimes.     

Interplay of Optical,Morphological, and Electronic Effects of ZnO Optical Spacers in Highly Efficient Polymer Solar Cells

Optical spacers based on metal oxide layers have been intensively studied in poly(3‐hexylthiophene) (P3HT) based polymer solar cells for optimizing light distribution inside the device, but to date, the potential of such a metal oxide spacer to improve the electronic performance of the polymer solar cells simultaneously has not yet be investigated. Here, a detailed study of performance improvement in high efficient polymer solar cells by insertion of solution‐processed ZnO optical spacer using ethanolamine surface modification is reported. Insertion of the modified ZnO optical spacer strongly improves the performance of polymer solar cells even in the absence of an increase in light absorption. The electric improvements of the device are related to improved electron extraction, reduced contact barrier, and reduced recombination at the cathode. Importantly, it is shown for the first time that the morphology of optical spacer layer is a crucial parameter to obtain highly efficient solar cells in normal device structures. By optimizing optical spacer effects, contact resistance, and morphology of ZnO optical spacers, poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6diyl] [3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl] thieno[3,4‐b]thiophenediyl]] (PTB7):[6,6]‐phenyl‐C71‐butyric acid (PC₇₀BM) bulk heterojunction solar cells with conversion efficiency of 7.6% are obtained in normal device structures with all‐solution‐processed interlayers.     

Understanding the Reduced Efficiencies of Organic Solar Cells Employing Fullerene Multiadducts as Acceptors

The use of fullerenes with two or more adducts as acceptors has been recently shown to enhance the performance of bulk‐heterojunction solar cells using poly(3‐hexylthiophene) (P3HT) as the donor. The enhancement is caused by a substantial increase in the open‐circuit voltage due to a rise in the fullerene lowest unoccupied molecular orbital (LUMO) level when going from monoadducts to multiadducts. While the increase in the open‐circuit voltage is obtained with many different polymers, most polymers other than P3HT show a substantially reduced photocurrent when blended with fullerene multiadducts like bis‐PCBM (bis adduct of Phenyl‐C₆₁‐butyric acid methyl ester) or the indene C₆₀ bis‐adduct ICBA. Here we investigate the reasons for this decrease in photocurrent. We find that it can be attributed partly to a loss in charge generation efficiency that may be related to the LUMO‐LUMO and HOMO‐HOMO (highest occupied molecular orbital) offsets at the donor‐acceptor heterojunction, and partly to reduced charge carrier collection efficiencies. We show that the P3HT exhibits efficient collection due to high hole and electron mobilities with mono‐ and multiadduct fullerenes. In contrast the less crystalline polymer Poly[[9‐(1‐octylnonyl)‐9H‐carbazole‐2,7‐diyl]‐2,5‐thiophenediyl‐2,1,3‐benzothiadiazole‐4,7‐diyl‐2,5‐thiophenediyl (PCDTBT) shows inefficient charge carrier collection, assigned to low hole mobility in the polymer and low electron mobility when blended with multiadduct fullerenes.     

Inverted Tandem Polymer Solar Cells with Polyethylenimine‐Modified MoOX/Al2O3:ZnO Nanolaminate as the Charge Recombination Layers

A new charge recombination layer for inverted tandem polymer solar cells is reported. A bilayer of MoO_X/Al₂O₃:ZnO nanolaminate is shown to enable efficient charge recombination in inverted tandem cells. A polymer surface modification on the MoO_X/Al₂O₃:ZnO nanolaminate bilayer increases the work function contrast between the two outward surfaces of the charge recombination layer, further improving the performance of tandem solar cells. An analysis of the electrical, optical, and surface properties of the charge recombination layer is presented. Inverted tandem polymer solar cells, with two photoactive layers comprising poly (3‐hexylthiophene) (P3HT):indene‐C₆₀ bisadduct (IC₆₀BA) for the bottom cell and poly[(4,8‐bis‐(2‐ethylhexyloxy)‐benzo[1,2‐b:4,5‐b']dithiophene)‐2,6‐diyl‐alt‐(4‐(2‐ethylhexanoyl)‐thieno[3,4‐b]thiophene))‐2,6‐diyl] (PBDTTT‐C):[6,6]‐phenyl C₆₁ butyric acid methyl ester (PC₆₀BM) for the top cell, yield an open‐circuit voltage of 1481 mV ± 15 mV, a short‐circuit current density of 7.1 mA cm^?2 ± 0.1 mA cm^?2, and a fill factor of 0.62 ± 0.01, resulting in a power conversion efficiency of 6.5% ± 0.1% under simulated AM 1.5G, 100 mW cm^?2 illumination.     

Morphology and Efficiency: The Case of Polymer/ZnO Solar Cells

The performance of polymer solar cells critically depends on the morphology of the interface between the donor‐ and acceptor materials that are used to create and transport charge carriers. Solar cells based on poly(3‐hexylthiophene) and ZnO were fully characterized in terms of their efficiency and three‐dimensional (3D) morphology on the nanoscale. Here, we establish a quantitative link between efficiency and morphology by using the experimental 3D morphology as direct input for a 3D optoelectronic device model. This model includes the effects of exciton diffusion and quenching; space‐charge; recombination, generation, drift and diffusion of charge carriers; and the injection/extraction of carriers at the contacts. The observed trend in internal quantum efficiency as a function of layer thickness is reproduced with a single set of parameters. Several morphological aspects that determine the internal quantum efficiency are discussed and compared to other organic solar cells. This first direct use of morphological data in an optoelectronic device model highlights the importance of morphology in solar cells.     

A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

Plasmonic Back Reflectors: A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

Work Function Control of Interfacial Buffer Layers for Efficient and Air‐Stable Inverted Low‐Bandgap Organic Photovoltaics

A water‐soluble cationic polythiophene derivative, poly[3‐(6‐{4‐tert‐butylpyridiniumyl}‐hexyl)thiophene‐2,5‐diyl] [P3(TBP)HT], is combined with anionic poly(3,4‐ethylenedioxythiophene):poly(p‐styrenesulfonate) (PEDOT:PSS) on indium tin oxide (ITO) substrates via electrostatic layer‐by‐layer (eLbL) assembly. By varying the number of eLbL layers, the electrode's work function is precisely controlled from 4.6 to 3.8 eV. These polymeric coatings are used as cathodic interfacial modifiers for inverted‐mode organic photovoltaics that incorporate a photoactive layer composed of either poly[(3‐hexylthiophene)‐2,5‐diyl] (P3HT) and the fullerene acceptor [6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or the low bandgap polymer [poly({4,8‐di(2‐ethylhexyloxyl)benzo[1,2‐b:4,5‐b′]dithiophene}‐2,6‐diyl)‐alt‐({5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}‐1,3‐diyl) (PBDTTPD)] and the electron acceptor [6,6‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM)]. The power conversion efficiency (PCE) of the resulting photovoltaic device is dependent on the composition of the eLbL‐assembled interface and permits the fabrication of devices with efficiencies of 3.8% and 5.6% for P3HT and PBDTTPD donor polymers, respectively. Notably, these devices demonstrate significant stability with a P3HT:PC₆₁BM system maintaining 83% of its original PCE after 1 year of storage and a PBDTTPD:PC₇₁BM system maintaining 97% of its original PCE after over 1000 h of storage in air, according to the ISOS‐D‐1 shelf protocol.     

Interfacial Engineering of P3HT/ZnO Hybrid Solar Cells Using Phthalocyanines: A Joint Theoretical and Experimental Investigation

Atomistic simulations and experimental investigations are combined to study heterojunction interfaces of hybrid polymer solar cells, with the aim to better understand and precisely predict their photovoltaic properties. The focus is on a hybrid ternary model system based on a poly(3‐hexylthiophene) (P3HT)/zinc phthalocyanine (ZnPc)/ZnO interface, in which a ZnPc interlayer is applied to improve the performance of the hybrid interface. Theoretical predictions of the ternary system are validated against the properties of a concrete P3HT/ZnPc/ZnO planar heterojunction device. The theoretical predictions closely agree with the photovoltaic properties obtained in P3HT/ZnPc/ZnO solar cells, indicating the strength of the method for modeling hybrid heterojunction interfaces. The theoretical and experimental results reveal that: i) ZnPc molecules in direct contact with a ZnO surface insert new energy levels due to a strong ZnPc/ZnO coupling, ii) electron injection from these new energy levels of ZnPc into ZnO is highly efficient, iii) the ZnPc/ZnO coupling strongly influences the energy levels of the ZnO and P3HT leading to a reduction of the open circuit voltage, and iv) charge carrier recombination at the P3HT/ZnO interface is reduced by the ZnPc interlayer. The intercalation of ZnPc leads to an increase in photocurrent as well as to an overall increase in power conversion.     

Controlling Hierarchy in Solution‐processed Polymer Solar Cells Based on Crosslinked P3HT

Understanding and controlling the morphology of donor/acceptor blends is critical for the development of solution processable organic solar cells. By crosslinking a poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) film we have been able to spin‐coat [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) onto the film to form a structure that is close to a bilayer, thus creating an ideal platform for investigating interdiffusion in this model system. Neutron reflectometry (NR) demonstrates that without any thermal treatment a smaller amount of PCBM percolates throughout the crosslinked P3HT when compared to a non‐crosslinked P3HT film. Using time‐resolved NR we also show thermal annealing increases the rate of diffusion, resulting in a near‐uniform distribution of PCBM throughout the polymer film. XPS measurements confirm the presence of both P3HT and PCBM at the annealed film's surface indicating that the two components are intermixed. Photovoltaic devices fabricated using this bilayer approach and suitable annealing conditions yielded comparable power conversion efficiencies to bulk heterojunction devices made from the same materials. The crosslinking procedure has also enabled the formation of patterned P3HT films by photolithography. Pillars with feature sizes down to 2 μm were produced and after subsequent deposition of PCBM and thermal annealing devices with efficiencies of up to 1.4% were produced.     

Morphology‐Limited Free Carrier Generation in Donor/Acceptor Polymer Blend Solar Cells Composed of Poly(3‐hexylthiophene) and Fluorene‐Based Copolymer

The charge generation and recombination dynamics in polymer/polymer blend solar cells composed of poly(3‐hexylthiophene) (P3HT, electron donor) and poly[2,7‐(9,9‐didodecylfluorene)‐alt‐5,5‐(4′,7′‐bis(2‐thienyl)‐2′,1′,3′‐benzothiadiazole)] (PF12TBT, electron acceptor) are studied by transient absorption measurements. In the unannealed blend film, charge carriers are efficiently generated from polymer excitons, but some of them recombine geminately. In the blend film annealed at 160 °C, on the other hand, the geminate recombination loss is suppressed and hence free carrier generation efficiency increases up to 74%. These findings suggest that P3HT and PF12TBT are intermixed within a few nanometers, resulting in impure PF12TBT and disordered P3HT domains. The geminate recombination is likely due to charge carriers generated on isolated polymer chains in the matrix of the other polymer and at the domain interface with disordered P3HT. The undesired charge loss by geminate recombination is reduced by both the purification of the PF12TBT‐rich domain and crystallization of the P3HT chains. These results show that efficient free carrier generation is not inherent to the polymer/fullerene domain interface, but is possible with polymer/polymer systems composed of crystalline donor and amorphous acceptor polymers, opening up a new potential method for the improvement of solar cell materials.     

Enhanced Light Harvesting in Organic Solar Cells Featuring a Biomimetic Active Layer and a Self‐Cleaning Antireflective Coating

Advanced light manipulation is extremely attractive for applications in organic optoelectronics to enhance light harvesting efficiency. A novel method of fabricating high‐efficiency organic solar cells (OSCs) is proposed using biomimetic moth eye nanostructures in a quasi‐periodic gradient shape active layer and an antireflective coating. A 24.3% increase in photocurrent is realized without sacrificing dark electrical properties, yielding a 22.2% enhancement in power conversion efficiency to a record of 7.86% for OSCs with a poly(3‐hexylthiophene‐2,5‐diyl):indene‐C60 bis‐adduct (P3HT:ICBA) active layer. The experimental and theoretical characterizations verify that the substantial improvement of OSCs is mainly ascribed to the self‐enhanced absorption resulting from the broadband polarization‐insensitive light trapping in biomimetic nanostructured active layer, the reduction in reflectance by the antireflective coating, and surface plasmonic effect excited by corrugated metallic electrode. It is noteworthy that the pathway described here is promising for opening up opportunities to realize high‐performance OSCs towards the future photovoltaic applications.     

High Fill Factor Polymer Solar Cells Incorporating a Low Temperature Solution Processed WO3 Hole Extraction Layer

We demonstrate solution‐processed tungsten trioxide (WO₃) incorporated as hole extraction layer (HEL) in polymer solar cells (PSCs) with active layers comprising either poly(3‐hexylthiophene) (P3HT) or poly[(4,4'‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,50‐diyl] (Si‐PCPDTBT) mixed with a fullerene derivative. The WO₃ layers are deposited from an alcohol‐based, surfactant‐free nanoparticle solution. A short, low‐temperature (80 °C) annealing is sufficient to result in fully functional films without the need for an oxygen‐plasma treatment. This allows the application of the WO₃ buffer layer in normal as well as inverted architecture solar cells. Normal architecture devices based on WO₃ HELs show comparable performance to the PEDOT:PSS reference devices with slightly better fill factors and open circuit voltages. Very high shunt resistances (over 1 MΩ cm²) and excellent diode rectification underline the charge selectivity of the solution‐processed WO₃ layers.     

Efficiency Enhancement of Polymer Solar Cells Based on Poly(3‐hexylthiophene)/Indene‐C70 Bisadduct via Methylthiophene Additive

Photovoltaic performance of polymer solar cells based on poly(3‐hexylthiophene) (P3HT) as the donor and indene‐C₇₀ bisadduct (IC₇₀BA) as the acceptor is improved by adding 3 vol% 3‐methylthiophene (MT) or 3‐hexylthiophene (HT) as processing additives. The results of UV‐vis absorption spectroscopy, X‐ray diffraction analysis and atomic force microscopy indicate that with the MT or HT processing additive, the active layer of the blend of P3HT/IC₇₀BA showed strengthened absorbance, enhanced crystallinity and improved film morphology. The power conversion efficiency (PCE) of the PSCs was improved from 5.80% for the device without the additive to 6.35% for the device with HT additive and to 6.69% with MT additive. The PCE of 6.69% is the top value reported so far for the PSCs based on P3HT.     

Non‐Fullerene Acceptor‐Based Bulk Heterojunction Polymer Solar Cells: Engineering the Nanomorphology via Processing Additives

The performance of bulk heterojunction solar cells made from blends of a non‐fullerene acceptor, N,N′‐bis(2‐ethylhexyl)‐2,6‐bis(5″‐hexyl‐[2,2′;5′,2″]terthiophen‐5yl)‐1,4,5,8‐naphthalene diimide (NDI‐3TH), and poly(3‐hexylthiophene) (P3HT) donor is enhanced 10‐fold by using a processing additive in conjunction with an electron‐blocking and a hole‐blocking buffer layers. The power conversion efficiency of P3HT:NDI‐3TH solar cells improves from 0.14% to 1.5% by using a processing additive (1,8‐diiodooctane) at an optimum concentration of 0.2 vol%, which is far below the 2‐3 vol% optimum concentrations found in polymer/fullerene systems. TEM and AFM imaging show that the size and connectivity of the NDI‐3TH domains in the phase‐separated P3HT:NDI‐3TH blends vary strongly with the concentration of the processing additive. These results demonstrate, for the first time, that processing additives can be effective in the optimization of the morphology and performance of bulk heterojunction polymer solar cells based on non‐fullerene acceptors.     

Donor‐Acceptor Interfacial Interactions Dominate Device Performance in Hybrid P3HT‐ZnO Nanowire‐Array Solar Cells

The adsorption of self‐assembled monolayers (SAMs) on metal oxide surfaces is a promising route to control electronic characteristics and surface wettability. Here, arylphosphonic acid derivatives are used to modulate the surface properties of vertically oriented ZnO nanowire arrays. Arylphosphonate‐functionalized ZnO nanowires are incorporated into hybrid organic‐inorganic solar cells in which infiltrated poly(3‐hexylthiophene) (P3HT) serves as the polymer donor. Strong correlations between device short‐circuit current density (J _sc) and power conversion efficiencies (PCEs) with ZnO surface functionalization species are observed and a weak correlation in the open‐circuit voltage (V _oc) is observed. Inverted solar cells fabricated with these treated interfaces exhibit PCEs as high as 2.1%, primarily due to improvements in J _sc. Analogous devices using untreated ZnO arrays having efficiencies of 1.6%. The enhancement in J _sc is attributed to surface passivation of ZnO by SAMs and enhanced wettability from P3HT, which improve charge transfer and reduce carrier recombination at the organic‐inorganic interface in the solar cells.     

Sequential Processing for Organic Photovoltaics: Design Rules for Morphology Control by Tailored Semi‐Orthogonal Solvent Blends

Design rules are presented for significantly expanding sequential processing (SqP) into previously inaccessible polymer:fullerene systems by tailoring binary solvent blends for fullerene deposition. Starting with a base solvent that has high fullerene solubility, 2‐chlorophenol (2‐CP), ellipsometry‐based swelling experiments are used to investigate different co‐solvents for the fullerene‐casting solution. By tuning the Flory‐Huggins χ parameter of the 2‐CP/co‐solvent blend, it is possible to optimally swell the polymer of interest for fullerene interdiffusion without dissolution of the polymer underlayer. In this way solar cell power conversion efficiencies are obtained for the PTB7 (poly[(4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)(3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl)]) and PC₆₁BM (phenyl‐C₆₁‐butyric acid methyl ester) materials combination that match those of blend‐cast films. Both semicrystalline (e.g., P3HT (poly(3‐hexylthiophene‐2,5‐diyl)) and entirely amorphous (e.g., PSDTTT (poly[(4,8‐di(2‐butyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)‐alt‐(2,5‐bis(4,4′‐bis(2‐octyl)dithieno[3,2‐b:2′3′‐d]silole‐2,6‐diyl)thiazolo[5,4‐d]thiazole)]) conjugated polymers can be processed into highly efficient photovoltaic devices using the solvent‐blend SqP design rules. Grazing‐incidence wide‐angle x‐ray diffraction experiments confirm that proper choice of the fullerene casting co‐solvent yields well‐ordered interdispersed bulk heterojunction (BHJ) morphologies without the need for subsequent thermal annealing or the use of trace solvent additives (e.g., diiodooctane). The results open SqP to polymer/fullerene systems that are currently incompatible with traditional methods of device fabrication, and make BHJ morphology control a more tractable problem.     

Polymer Blend Solar Cells Based on a High‐Mobility Naphthalenediimide‐Based Polymer Acceptor: Device Physics,Photophysics and Morphology

A high electron mobility polymer, poly{[N,N’‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5’‐(2,2’‐bithiophene) (P(NDI2OD‐T2)) is investigated for use as an electron acceptor in all‐polymer blends. Despite the high bulk electron mobility, near‐infrared absorption band and compatible energy levels, bulk heterojunction devices fabricated with poly(3‐hexylthiophene) (P3HT) as the electron donor exhibit power conversion efficiencies of only 0.2%. In order to understand this disappointing photovoltaic performance, systematic investigations of the photophysics, device physics and morphology of this system are performed. Ultra‐fast transient absorption spectroscopy reveals a two‐stage decay process with an initial rapid loss of photoinduced polarons, followed by a second slower decay. This second slower decay is similar to what is observed for efficient P3HT:PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) blends, however the initial fast decay that is absent in P3HT:PCBM blends suggests rapid, geminate recombination of charge pairs shortly after charge transfer. X‐ray microscopy reveals coarse phase separation of P3HT:P(NDI2OD‐T2) blends with domains of size 0.2 to 1 micrometer. P3HT photoluminescence, however, is still found to be efficiently quenched indicating intermixing within these mesoscale domains. This hierarchy of phase separation is consistent with the transient absorption, whereby localized confinement of charges on isolated chains in the matrix of the other polymer hinders the separation of interfacial electron‐hole pairs. These results indicate that local, interfacial processes are the key factor determining the overall efficiency of this system and highlight the need for improved morphological control in order for the potential benefit of high‐mobility electron accepting polymers to be realized.     

Direct Correlation of the Organic Solar Cell Device Performance to the In‐Depth Distribution of Highly Ordered Polymer Domains in Polymer/Fullerene Films

This study correlates the device performance of organic solar cells and the electronic charge transport within polymer/fullerene films, directly to the optical order of the polymer. The optical order was measured by spectroscopic ellipsometry and evaluated by our previously derived model. We were able to determine the in‐depth distribution of higher and lower ordered poly(3‐hexylthiophene) (P3HT) domains within an [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) matrix. The over the film thickness integrated volume fraction of highly ordered P3HT domains could be directly correlated to the corresponding solar cell device performance. We are able to describe various thermally annealing conditions between room‐temperature and 200 °C.