Low‐Temperature Micro‐Solid Oxide Fuel Cells with Partially Amorphous La0.6Sr0.4CoO3‐δ Cathodes

Partially amorphous La_0.6Sr_0.4CoO_3‐δ (LSC) thin‐film cathodes are fabricated using pulsed laser deposition and are integrated in free‐standing micro‐solid oxide fuel cells (micro‐SOFC) with a 3YSZ electrolyte and a Pt anode. A low degree of crystallinity of the LSC layers is achieved by taking advantage of the miniaturization of the cells, which permits low‐temperature operation (300–450 °C). Thermomechanically stable micro‐SOFC are obtained with strongly buckled electrolyte membranes. The nanoporous columnar microstructure of the LSC layers provides a large surface area for oxygen incorporation and is also believed to reduce the amount of stress at the cathode/electrolyte interface. With a high rate of failure‐free micro‐SOFC membranes, it is possible to avoid gas cross‐over and open‐circuit voltages of 1.06 V are attained. First power densities as high as 200–262 mW cm^?2 at 400–450 °C are achieved. The area‐specific resistance of the oxygen reduction reaction is lower than 0.3 Ω cm² at 400 °C around the peak power density. These outstanding findings demonstrate that partially amorphous oxides are promising electrode candidates for the next‐generation of solid oxide fuel cells working at low‐temperatures.     

Microstructure of Nanoscaled La0.6Sr0.4CoO3‐δ Cathodes for Intermediate‐Temperature Solid Oxide Fuel Cells

Nanocrystalline La_1‐xSr_xCoO_3‐δ (LSC) thin films with a nominal Sr‐content of x = 0.4 were deposited on Ce_0.9Gd_0.1O_1.95 electrolyte substrates using a low temperature sol‐gel process. The structural and chemical properties of the LSC thin films were studied after thermal treatment, which included a calcination step and a variable, extended annealing time at 700 °C or 800 °C. Transmission electron microscopy combined with selected‐area electron diffraction, energy‐dispersive X‐ray spectrometry, and scanning transmission electron microscopy tomography was applied for the investigation of grain size, porosity, microstructure, and analysis of the local chemical composition and element distribution on the nanoscale. The area specific resistance (ASR) values of the thin film LSC cathodes, which include the lowest ASR value reported so far (ASR_chem = 0.023 Ωcm² at 600 °C) can be interpreted on the basis of the structural and chemical characterization.     

MnPO4‐Coated Li(Ni0.4Co0.2Mn0.4)O2 for Lithium(‐Ion) Batteries with Outstanding Cycling Stability and Enhanced Lithiation Kinetics

Herein, the successful synthesis of MnPO₄‐coated LiNi_0.4Co_0.2Mn_0.4O₂ (MP‐NCM) as a lithium battery cathode material is reported. The MnPO₄ coating acts as an ideal protective layer, physically preventing the contact between the NCM active material and the electrolyte and, thus, stabilizing the electrode/electrolyte interface and preventing detrimental side reactions. Additionally, the coating enhances the lithium de‐/intercalation kinetics in terms of the apparent lithium‐ion diffusion coefficient. As a result, MP‐NCM‐based electrodes reveal greatly enhanced C‐rate capability and cycling stability—even under exertive conditions like extended operational potential windows, elevated temperature, and higher active material mass loadings. This superior electrochemical behavior of MP‐NCM compared to as‐synthesized NCM is attributed to the superior stability of the electrode/electrolyte interface and structural integrity when applying a MnPO₄ coating. Employing an ionic liquid as an alternative, intrinsically safer electrolyte system allows for outstanding cycling stabilities in a lithium‐metal battery configuration with a capacity retention of well above 85% after 2000 cycles. Similarly, the implementation in a lithium‐ion cell including a graphite anode provides stable cycling for more than 2000 cycles and an energy and power density of, respectively, 376 Wh kg^?1 and 1841 W kg^?1 on the active material level.     

Application of NMR spectroscopy for assignment of the absolute configuration of 8‐tert‐butyl‐2‐hydroxy‐7‐methoxy‐8‐methyl‐9‐oxa‐6‐azaspiro[4.5]dec‐6‐en‐10‐one

In order to assign the absolute configurations of 8‐tert‐butyl‐2‐hydroxy‐7‐methoxy‐8‐methyl‐9‐oxa‐6‐azaspiro[4.5]dec‐6‐en‐10‐one ( 2a , 2b ), their esters ( 5a , 5b , 5c , 5d ) with (R)‐ or (S)‐2‐methoxyphenylacetic acid ( 4a , 4b ) have been synthesized. The absolute configurations of these compounds have been determined on the basis of NOESY correlations between the protons of the tert‐butyl group and the cyclopentane fragment of the molecules. The crucial part of this analysis was assignment of the absolute configuration at C‐5. Additionally, by calculation of the chemical shift anisotropy, δ^RS, for the relevant protons, it was also possible to confirm the absolute configurations at the C‐2 centres of compounds 2a , 2b and 5a , 5b , 5c , 5d . Chirality, 25:422–426, 2013.© 2013 Wiley Periodicals, Inc.     

All‐Manganese‐Based Binder‐Free Stretchable Lithium‐Ion Batteries

Advanced electrode materials with bendability and stretchability are critical for the rapid development of fully flexible/stretchable lithium‐ion batteries. However, the sufficiently stretchable lithium‐ion battery is still underdeveloped that is one of the biggest challenges preventing from realizing fully deformable power sources. Here, a low‐temperature hydrothermal synthesis of a cathode material for stretchable lithium‐ion battery is reported by the in situ growth of LiMn₂O₄ (LMO) nanocrystals inside 3D carbon nanotube (CNT) film networks. The LMO/CNT film composite has demonstrated the chemical bonding between the LMO active materials and CNT scaffolds, which is the most important characteristic of the stretchable electrodes. When coupled with a wrinkled MnO_x /CNT film anode, a binder‐free, all‐manganese‐based stretchable full battery cell is assembled which delivers a high average specific capacity of ≈97 mA h g^?1 and stabilizes after over 300 cycles with an enormous strain of 100%. Furthermore, combining with other merits such as low cost, natural abundance, and environmentally friendly, the all‐manganese design is expected to accelerate the practical applications of stretchable lithium‐ion batteries for fully flexible and biomedical electronics.     

HS‐SPME‐GC‐FID method for detection and quantification of Bacillus cereus ATCC 10702 mediated 2‐acetyl‐1‐pyrroline

A rapid micro‐scale solid‐phase micro‐extraction (SPME) procedure coupled with gas‐chromatography with flame ionized detector (GC‐FID) was used to extract parts per billion levels of a principle basmati aroma compound “2‐acetyl‐1‐pyrroline” (2‐AP) from bacterial samples. In present investigation, optimization parameters of bacterial incubation period, sample weight, pre‐incubation time, adsorption time, and temperature, precursors and their concentrations has been studied. In the optimized conditions, detection of 2‐AP produced by Bacillus cereus ATCC10702 using only 0.5 g of sample volume was 85 μg/kg. Along with 2‐AP, 15 other compounds produced by B. cereus were also reported out of which 14 were reported for the first time consisting mainly of (E)?2‐hexenal, pentadecanal, 4‐hydroxy‐2‐butanone, n‐hexanal, 2–6‐nonadienal, 3‐methoxy‐2(5H) furanone and 2‐acetyl‐1‐pyridine and octanal. High recovery of 2‐AP (87 %) from very less amount of B. cereus samples was observed. The method is reproducible fast and can be used for detection of 2‐AP production by B. cereus. © 2014 American Institute of Chemical Engineers Biotechnol. Prog., 30:1356–1363, 2014     

Validated spectrofluorimetric method for the determination of carbamazepine in pharmaceutical dosage forms after reaction with 4‐chloro‐7‐‐nitrobenzo‐2‐oxa‐1,3‐diazole (NBD‐Cl)

A sensitive and simple spectrofluorimetric method has been developed and validated for the determination of the anti‐epileptic drug carbamazepine (CBZ) in its dosage forms. The method was based on a nucleophilic substitution reaction of CBZ with 4‐chloro‐7‐nitrobenzo‐2‐ oxa‐1,3‐diazole (NBD‐Cl) in borate buffer (pH 9) to form a highly fluorescent derivative that was measured at 530 nm after excitation at 460 nm. Factors affecting the formation of the reaction product were studied and optimized, and the reaction mechanism was postulated. The fluorescence–concentration plot is rectilinear over the range of 0.6–8 µg/mL with limit of detection of 0.06 µg/mL and limit of quantitation of 0.19 µg/mL. The method was applied to the analysis of commercial tablets and the results were in good agreement with those obtained using the reference method. Validation of the analytical procedures was evaluated according to ICH guidelines. Copyright © 2015 John Wiley & Sons, Ltd.     

Enantioselective resolution of 4‐chloromandelic acid by liquid–liquid extraction using 2‐chloro‐N‐carbobenzyloxy‐L‐amino acid

A liquid–liquid extraction resolution of 4‐chloro‐mandelic acid (4‐ClMA) was studied by using 2‐chloro‐N‐carbobenzyloxy‐L‐amino acid (2‐Cl‐Z‐AA) as a chiral extractant. Important factors affecting the extraction efficiency were investigated, including the type of chiral extractant, pH value of aqueous phase, initial concentration of chiral extractant in organic phase, initial concentration of 4‐ClMA in aqueous phase, and resolution temperature. It was observed that the concentration of (R)‐4‐ClMA was much higher than that of (S)‐4‐ClMA in organic phase due to a higher stability of the complex formed between (R)‐4‐ClMA and 2‐Cl‐Z‐AA. A separation factor (α) of 3.05 was obtained at 0.02 mol/L 2‐Cl‐Z‐Valine dissolved in dichloromethane, pH of 2.0, concentration of 4‐ClMA of 0.11 mmol/Land T of 296.7K.     

High‐Performance Liquid Chromatographic Enantioseparation of Unusual Isoxazoline‐Fused 2‐Aminocyclopentanecarboxylic Acids on (+)‐(18‐Crown‐6)‐2,3,11,12‐Tetracarboxylic Acid‐Based Chiral Stationary Phases

The enantiomers of four unusual isoxazoline‐fused 2‐aminocyclopentanecarboxylic acids were directly separated on chiral stationary phases containing (+)‐(18‐crown‐6)‐2,3,11,12‐tetracarboxylic acid as chiral selector. The nature of the alcoholic modifier (MeOH, EtOH, IPA) exerted a great effect on the retention, whereas the selectivity and resolution did not change substantially. Two types of dependence of retention on alcohol content were detected: k₁ increased continuously with increasing alcohol content or a U‐shaped retention curve was observed. A comparison of the chromatographic data obtained with HCOOH, AcOH, TFA, HClO₄, H₂SO₄, or H₃PO₄ as acidic modifier at a constant concentration demonstrated that in most cases, larger k values were obtained on the application of AcOH or HCOOH, and an increase of the acid content resulted in a decrease of retention. Some mechanistic aspects of the chiral recognition process are discussed with respect to the structures of the analytes and selector. The sequence of elution of the enantiomers was determined in all cases. Chirality 24:817‐824, 2012. © 2012 Wiley Periodicals, Inc.     

Synthesis and Olfactory Characterization of Silicon‐Containing Derivatives of the Acyclic Lily‐of‐the‐Valley Odorant 5,7,7‐Trimethyl‐4‐methylideneoctanal

5‐Methyl‐4‐methylidene‐6‐(trimethylsilyl)hexanal ( 1b ), a sila analog of the acyclic lily‐of‐the‐valley odorant 5,7,7‐trimethyl‐4‐methylideneoctanal ( 1a ), and the Si‐containing derivatives 2 – 6 were prepared in multistep syntheses, starting from Cl₃SiH and Cl₂SiMe₂, respectively. Compounds 1b, 2 – 6 , and their new precursors were characterized by elemental analyses (C, H, N) and NMR spectroscopic studies (¹H, ¹³C, ¹⁵N, and ²⁹Si). To gain more information about the structure? odor correlation in the family of lily‐of‐the‐valley or ‘muguet’ odorants, C/Si analogs 1a / 1b and derivatives 2 – 6 were evaluated for their olfactory properties.     

2H‐Pyran‐2‐one and 2H‐Furan‐2‐one Derivatives from the Plant Endophytic Fungus Pestalotiopsis fici

Two new α‐pyrones (=2H‐pyran‐2‐ones), ficipyrones A and B ( 1 and 2 , resp.), and two new α‐furanones (=2H‐furan‐2‐ones), ficifuranones A and B ( 3 and 4 , resp.), together with three known metabolites, antibiotic F 0368 ( 5 ), hydroxyseiridin ( 6 ), and hydroxyisoseiridin ( 7 ), were isolated from solid cultures of the plant endophytic fungus Pestalotiopsis fici. Their structures were elucidated primarily by NMR spectroscopy, and the absolute configuration of 1 was deduced from the circular‐dichroism (CD) data. Compound 1 showed antifungal activity against the plant pathogen Gibberella zeae (CGMCC 3.2873) with an IC₅₀ value of 15.9 μM .     

Homo‐C‐nucleoside analogs IV. Synthesis of 4‐(2,5‐anhydro‐D‐altro‐pentitol‐1‐yl)‐2‐phenyl‐2H‐1,2,3‐triazole homo‐C‐nucleoside. CD assignment of the absolute configuration of the carbon bridge

Dehydrative cyclization of 4‐(D‐altro ‐pentitol‐1‐yl)2‐phenyl‐2H ‐1,2,3‐triazole in basic medium with one moler equivalent of p‐toluene sulfonyl chloride in pyridine solution gave the homo‐C‐ nucleoside 4‐(2,5‐anhydro‐D‐altro ‐1‐yl)‐2‐phenyl‐2H ‐1,2,3‐triazole. The structure and anomeric configuration was determined by acylation, nuclear magnetic resonance (NMR), and mass spectroscopy. The stereochemistry at the carbon bridge of homo‐C‐ nucleoside 2‐phenyl‐2H ‐1,2,3‐triazoles was determined by circular dichroism (CD) spectroscopy.     

Asymmetrically simultaneous synthesis of L‐homophenylalanine and N6‐protected‐2‐oxo‐6‐amino‐hexanoic acid by engineered Escherichia coli aspartate aminotransferase

L ‐Homophenylalanine (L ‐HPA) and N⁶‐protected‐2‐oxo‐6‐amino‐hexanoic acid (N⁶‐protected‐OAHA) can be used as building blocks for the manufacture of angiotensin‐converting enzyme inhibitors. To synthesize L ‐HPA and N⁶‐protected‐OAHA simultaneously from 2‐oxo‐4‐phenylbutanoic acid (OPBA) and N⁶‐protected‐L ‐lysine, several variants of Escherichia coli aspartate aminotransferase (AAT) were developed by site‐directed mutagenesis and their catalytic activities were investigated. Three kinds of N⁶‐protected‐L ‐lysine were tested as potential amino donors for the bioconversion process. AAT variants of R292E/L18H and R292E/L18T exhibited specific activities of 0.70±0.01 U/mg protein and 0.67±0.02 U/mg protein to 2‐amino‐6‐tert‐butoxycarbonylamino‐hexanoic acid (BOC‐lysine) and 2‐amino‐6‐(2,2,2‐trifluoro‐acetylamino)‐hexanoic acid, respectively. E. coli cells expressing R292E/L18H variant were able to convert OPBA and BOC‐lysine to L ‐HPA and 2‐oxo‐6‐tert‐butoxycarbonylamino‐hexanoic acid (BOC‐OAHA) with 96.2% yield in 8 h. This is the first report demonstrating a process for the simultaneous production of two useful building blocks, L ‐HPA and BOC‐OAHA. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

The special optical properties and application of the heterocyclic compound diethyl 6‐anilino‐5H‐2,3‐dithia‐5,7‐diazacyclopenta(cd)indene‐1,4‐dicarboxylate

The heterocyclic compound diethyl 6‐anilino‐5H‐2,3‐dithia‐5,7‐diazacyclopenta(cd)indene‐1,4‐dicarboxylate (D1) was found to form highly emissive aggregates in polar solvents, and the aggregate emission can be tuned by the simple addition of water to a dimethylsulfoxide solution. A theoretical study based on Density functional theory (DFT) calculations, shows that intermolecular interactions of D1 with solvent may be potential factors in the fluorescence change. In addition, the phenyl ring in D1 plays an important role because of its response to solvent. In the non‐aggregated state, deprotonation of the N–H of D1 can proceed easily on the addition of base, and the deprotonated compound might interact with Ag⁺, resulting in a significant change in color and fluorescence quenching, which make it a potential chemosensor for the selective detection of trace amounts of Ag⁺. Copyright © 2013 John Wiley & Sons, Ltd.     

Resolution of 1‐n‐Butyl‐3‐Methyl‐3‐Phospholene 1‐Oxide With TADDOL Derivatives and Calcium Salts of O,O'‐Dibenzoyl‐(2R,3R)‐ or O,O'‐di‐p‐Toluoyl‐(2R,3R)‐tartaric Acid

The resolution methods applying (?)‐(4R,5R)‐4,5‐bis(diphenylhydroxymethyl)‐2,2‐dimethyldioxolane (“TADDOL”), (?)‐(2R,3R)‐α,α,α',α'‐tetraphenyl‐1,4‐dioxaspiro[4.5]decan‐2,3‐dimethanol (“spiro‐TADDOL”), as well as the acidic and neutral Ca²⁺ salts of (?)‐O,O'‐dibenzoyl‐ and (?)‐O,O'‐di‐p‐toluoyl‐(2R,3R)‐tartaric acid were extended for the preparation of 1‐n‐butyl‐3‐methyl‐3‐phospholene 1‐oxide in optically active form. In one case, the intermediate diastereomeric complex could be identified by single‐crystal X‐ray analysis. The absolute P‐configuration of the enantiomers of the phospholene oxide was also determined by comparing the experimentally obtained and calculated CD spectra. Chirality 26:174–182, 2014. © 2014 Wiley Periodicals, Inc.     

ER‐to‐lysosome‐associated degradation of proteasome‐resistant ATZ polymers occurs via receptor‐mediated vesicular transport

Maintenance of cellular proteostasis relies on efficient clearance of defective gene products. For misfolded secretory proteins, this involves dislocation from the endoplasmic reticulum (ER) into the cytosol followed by proteasomal degradation. However, polypeptide aggregation prevents cytosolic dislocation and instead activates ill‐defined lysosomal catabolic pathways. Here, we describe an ER‐to‐lysosome‐associated degradation pathway (ERLAD) for proteasome‐resistant polymers of alpha1‐antitrypsin Z (ATZ). ERLAD involves the ER‐chaperone calnexin (CNX) and the engagement of the LC3 lipidation machinery by the ER‐resident ER‐phagy receptor FAM134B, echoing the initiation of starvation‐induced, receptor‐mediated ER‐phagy. However, in striking contrast to ER‐phagy, ATZ polymer delivery from the ER lumen to LAMP1/RAB7‐positive endolysosomes for clearance does not require ER capture within autophagosomes. Rather, it relies on vesicular transport where single‐membrane, ER‐derived, ATZ‐containing vesicles release their luminal content within endolysosomes upon membrane:membrane fusion events mediated by the ER‐resident SNARE STX17 and the endolysosomal SNARE VAMP8. These results may help explain the lack of benefits of pharmacologic macroautophagy enhancement that has been reported for some luminal aggregopathies.