Electrochemical Reaction of Lithium with Nanostructured Silicon Anodes: A Study by In‐Situ Synchrotron X‐Ray Diffraction and Electron Energy‐Loss Spectroscopy

Silicon‐based anodes are an appealing alternative to graphite for lithium‐ion batteries because of their extremely high capacity. However, poor cycling stability and slow kinetics continue to limit the widespread use of silicon in commercial batteries. Performance improvement has been often demonstrated in nanostructured silicon electrodes, but the reaction mechanisms involved in the electrochemical lithiation of nanoscale silicon are not well understood. Here, in‐situ synchrotron X‐ray diffraction is used to monitor the subtle structural changes occurring in Si nanoparticles in a Si‐C composite electrode during lithiation. Local analysis by electron energy‐loss spectroscopy and transmission electron microscopy is performed to interrogate the nanoscale morphological changes and phase evolution of Si particles at different depths of discharge. It is shown that upon lithiation, Si nanoparticles behave quite differently than their micrometer‐sized counterparts. Although both undergo an electrochemical amorphization, the micrometer‐sized silicon exhibits a linear transformation during lithiation, while a two‐step process occurs in the nanoscale Si. In the first half of the discharge, lithium reacts with surfaces, grain boundaries and planar defects. As the reaction proceeds and the cell voltage drops, lithium consumes the crystalline core transforming it into amorphous Li_xSi with a primary particle size of just a few nanometers. Unlike the bulk silicon electrode, no Li₁₅Si₄ or other crystalline Li_xSi phases were formed in nanoscale Si at the fully‐lithiated state.     

In Situ EXAFS‐Derived Mechanism of Highly Reversible Tin Phosphide/Graphite Composite Anode for Li‐Ion Batteries

A novel Sn₄P₃/graphite composite anode material with superior capacity and cycling performance (651 mA h g^?1 after 100 cycles) is investigated by in situ X‐ray absorption spectroscopy. Extended X‐ray absorption fine structure modeling and detailed analysis of local environment changes are correlated to the cell capacity and reveal the mechanism of lithiation/delithiation process. Results show that in the first two lithiation/delithiation cycles crystalline Sn₄P₃ is fully converted to an amorphous SnP_x phase, which in further cycles participates in reversible conversion and alloying reactions. The superior reversibility of this material is attributed to the highly dispersed SnP_x in the graphite matrix, which provides enhanced electrical conductivity and prevents aggregation of Sn clusters during the lithiation/delithiation process. The gradual capacity fading in long‐term cycling is attributed to the observed increase in the size and the amount of metallic Sn clusters in the delithiated state, correlated to the reduced recovery of the SnP_x phase. This paper reveals the mechanism responsible for the highly reversible tin phosphides and provides insights for improving the capacity and cycle life of conversion and alloying materials.     

Si‐Encapsulating Hollow Carbon Electrodes via Electroless Etching for Lithium‐Ion Batteries

Remarkable improvements in the electrochemical performance of Si materials for Li‐ion batteries have been recently achieved, but the inherent volume change of Si still induces electrode expansion and external cell deformation. Here, the void structure in Si‐encapsulating hollow carbons is optimized in order to minimize the volume expansion of Si‐based anodes and improve electrochemical performance. When compared to chemical etching, the hollow structure is achieved via electroless etching is more advanced due to the improved electrical contact between carbon and Si. Despite the very thick electrodes (30 ～ 40 μm), this results in better cycle and rate performances including little capacity fading over 50 cycles and 1100 mA h g^?1 at 2C rate. Also, an in situ dilatometer technique is used to perform a comprehensive study of electrode thickness change, and Si‐encapsulating hollow carbon mitigates the volume change of electrodes by adoption of void space, resulting in a small volume increase of 18% after full lithiation corresponding with a reversible capacity of about 2000 mA h g^?1.     

A Novel Phase of Li15Si4 Synthesized under Pressure

Li₁₅Si₄, the only crystalline phase that forms during lithiation of the Si anode in lithium‐ion batteries, is found to undergo a structural transition to a new phase at 7 GPa. Despite the large unit cell of Li₁₅Si₄ (152 atoms in the unit cell), ab initio evolutionary metadynamics (using the USPEX code) successfully predicts the atomic structure of this new phase (β‐Li₁₅Si₄), which has an orthorhombic structure with an Fdd2 space group. In the new β‐Li₁₅Si₄ phase Si atoms are isolated by Li atoms analogous to the original cubic phase (α‐Li₁₅Si₄), whereas the atomic packing is more efficient owing to the higher Si? Li coordination number and shorter Si? Li, Li? Li bonds. β‐Li₁₅Si₄ has substantially larger elastic moduli compared with α‐Li₁₅Si₄, and has a good electrical conductivity. As a result, β‐Li₁₅Si₄ has superior resistance to deformation and fracture under stress. The theoretical volume expansion of Si would decrease 25% if it transforms to β‐Li₁₅Si₄, instead of α‐Li₁₅Si₄, during lithiation. Moreover, β‐Li₁₅Si₄ can be recovered back to ambient pressure, providing opportunities to further investigate its properties and potential applications.     

Operando Quantification of (De)Lithiation Behavior of Silicon–Graphite Blended Electrodes for Lithium‐Ion Batteries

Due to the high lithium capacity of silicon, the composite (blended) electrodes containing silicon (Si) and graphite (Gr) particles are attractive alternatives to the all‐Gr electrodes used in conventional lithium‐ion batteries. In this Communication, the lithiation and delithiation in the Si and Gr particles in a 15 wt% Si composite electrode is quantified for each component using energy dispersive X‐ray diffraction. This quantification is important as the components cycle in different potential regimes, and interpretation of cycling behavior is complicated by the potential hysteresis displayed by Si. The lithiation begins with Li alloying with Si; lithiation of Gr occurs at later stages when the potential dips below 0.2 V (all potentials are given vs Li/Li⁺). In the 0.2–0.01 V range, the relative lithiation of Si and Gr is ≈58% and 42%, respectively. During delithiation, Li⁺ ion extraction occurs preferentially from Gr in the 0.01–0.23 V range and from Si in the 0.23–1.0 V range; that is, the delithiation current is carried sequentially, first by Gr and then by Si. These trends can be used for rational selection of electrochemical cycling windows that limits volumetric expansion in Si particles, thereby extending cell life.     

Spray Deposition of Silver Nanowire Electrodes for Semitransparent Solid‐State Dye‐Sensitized Solar Cells

Transparent top electrodes for solid‐state dye‐sensitized solar cells (ssDSCs) allow for fabrication of mechanically stacked ssDSC tandems, partially transparent ssDSCs for building integration, and ssDSCs on metal foil substrates. A solution‐processed, highly transparent, conductive electrode based on PEDOT:PSS [poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)] and spray‐deposited silver nanowires (Ag NWs) is developed as an effective top contact for ssDSCs. The electrode is solution‐deposited using conditions and solvents that do not damage or dissolve the underlying ssDSC and achieves high performance: a peak transmittance of nearly 93% at a sheet resistance of 18 Ω/square – all without any annealing that would harm the ssDSC. The role of the PEDOT:PSS in the electrode is twofold: it ensures ohmic contact between the ssDSC 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)9,9′‐spirobifluorene (Spiro‐OMeTAD) overlayer and the silver nanowires and it decreases the series resistance of the device. Semitransparent ssDSCs with D35 dye fabricated using this Ag NW/PEDOT:PSS transparent electrode show power conversion efficiencies of 3.6%, nearly as high as a reference device using an evaporated silver electrode (3.7%). In addition, the semitransparent ssDSC shows high transmission between 700–1100 nm, a necessity for use in efficient tandem devices. Such an electrode, in combination with efficient ssDSCs or hybrid perovskite‐sensitized solar cells, can allow for the fabrication of efficient, cost‐effective tandem photovoltaics.     

CoS NWs/Au Hybridized Networks as Efficient Counter Electrodes for Flexible Sensitized Solar Cells

A newly designed counter electrode (CE) composed of a hybridized structure of Au networks and cobalt sulfide (CoS) nanowire (NW) arrays is presented for flexible dye‐sensitized solar cells (DSSCs) and quantum dot‐sensitized solar cells (QDSSCs). The sheet resistance of the Au networks electrode is ≈10 Ω sq^?1 with a transmittance up to 90%. The CoS NWs/Au hybridized networks show excellent electrocatalytic activity and lower charge transfer resistance toward the reduction of both S_x^2? ions and I₃^? ions. The hybridized electrode exhibits remarkable mechanical strength and no obvious changes in morphology and sheet resistance even after 500 bending cycles; 3.13% and 4.73% efficiency are obtained by utilizing CoS/Au hybridized networks as CEs in TiO₂ nanotube array (TNAR) based DSSCs and QDSSCs. This work provides a novel approach to fabricate flexible, transparent, conductive, and catalytically active electrodes for QDSSCs and DSSCs and pomotes the development of transparent percolation conductive films for photovoltaics.     

A Novel Codoping Approach for Enhancing the Performance of LiFePO4 Cathodes

By combining experimental and theoretical studies, we have demonstrated that donor‐acceptor charge‐compensating codoping is a promising approach to significantly enhance the rate performance of LiFePO₄ cathodes. Our density‐functional theory calculation predicts that codoping with Si on the P site and F on the O site modifies the nature of the conduction band edge of LiFePO₄ from localized Fe 3d derived states to more delocalized F s and cation s derived states. This effect, thus changes the carrier transport from a poloron‐like to a band‐like mechanism, and consequently leads to significant improvement in the electrical conductivity of LiFePO₄. Most importantly, our comparative doping experiments show that the electrical conductivity of Si _P ‐F_O codoped LiFePO₄ exhibits at least 2 to 3 orders of magnitude increase in electrical conductivity as compared to that of un‐doped LiFePO₄. Because of the dramatic improvement of electrical conductivity, the optimal Si‐F codoped LiFePO₄ shows both a much higher rate‐capability than un‐doped LiFePO₄ or LiFePO₄ solely doped with either Si or F. Furthermore, we also believe that the charge‐compensating codoping approach may be employed to improve the performance of other cathode materials suffering from inferior electrical conductivities due to localized conduction band states.     

Lithiation Mechanism of Methylated Amorphous Silicon Unveiled by Operando ATR‐FTIR Spectroscopy

The lithiation mechanism of methylated amorphous silicon, a‐Si_1?x(CH₃)_x:H, with various methyl contents (x = 0 ‐ 0.12) is investigated using operando attenuated total reflection Fourier transform infrared spectroscopy. As in hydrogenated amorphous silicon, a‐Si:H, the first lithiation proceeds via a two‐phase mechanism. The concentration of the invading Li‐rich phase nonmonotonously depends on the methyl content of the active material. This behavior is tentatively explained by two distinct effects: a softening of the material due to a methyl‐induced lowering of its reticulation degree and its cohesion, and the presence of nanovoids at high enough methyl content.     

Electrochemical Stiffness Changes in Lithium Manganese Oxide Electrodes

In situ strain and stress measurements are performed on composite electrodes to monitor potential‐dependent stiffness changes in lithium manganese oxide (LiMn₂O₄). Lithium insertion and removal results in asynchronous strain and stress generation in the electrode. Electrochemical stiffness changes are calculated by combining coordinated stress and strain measurements. The electrode experiences dramatic changes in electrochemical stiffness due to potential‐dependent Li⁺ ion intercalation mechanisms. The development of stress in the early stages of delithiation (at ≈3.95 V) due to a kinetic barrier at the electrode surface gives rise to stiffness changes in the electrode. Strain generation due to phase transformations reduces stiffness in the electrode at 4.17 V during delithiation and at 4.11 V during lithiation. During lithiation, stress generation due to Coulombic repulsions between occupied and incoming Li⁺ ions leads to stiffening of the electrode at 3.96 V. The electrode also experiences greater changes in stiffness during delithiation compared to lithiation. These changes in electrochemical stiffness provide insight into the interplay between mechanical and electrochemical properties which control electrode response to lithiation and delithiation.     

MXene‐Contacted Silicon Solar Cells with 11.5% Efficiency

MXene, a new class of 2D materials, has gained significant attention owing to its attractive electrical conductivity, tunable work function, and metallic nature for wide range of applications. Herein, delaminated few layered Ti₃C₂T_x MXene contacted Si solar cells with a maximum power conversion efficiency (PCE) of ≈11.5% under AM1.5G illumination are demonstrated. The formation of an Ohmic junction of the metallic MXene to n⁺‐Si surface efficiently extracts the photogenerated electrons from n⁺np⁺‐Si, decreases the contact resistance, and suppresses the charge carrier recombination, giving rise to excellent open‐circuit voltage and short‐circuit current density. The rapid thermal annealing process further improves the electrical contact between Ti₃C₂T_x MXene and n⁺‐Si surface by reducing sheet resistance, increasing electrical conductivity, and decreasing cell series resistance, thus leading to a remarkable improvement in fill factor and overall PCE. The work demonstrated here can be extended to other MXene compositions as potential electrodes for developing highly performing solar cells.     

Silicon Nanowires and Lithium Cobalt Oxide Nanowires in Graphene Nanoribbon Papers for Full Lithium Ion Battery

Described here is the production and characterization of a scalable method to produce 3D structured lithium ion battery anodes using free‐standing papers of porous silicon nanowires (Si‐NW) and graphene nanoribbons (GNRs). Using simple filtration methods, GNRs and Si‐NWs can be entangled into a mat thereby forming Si‐NW GNR papers. This produces anodes with high gravimetric capacity (up to 2500 mA h g^?1) and high areal and volumetric capacities (up to 11 mA h cm^?2 and 3960 mA h cm?³). The compact structure of the anode is possible since the GNR volume occupies a high proportion of empty space within the composite paper. These Si‐NW/GNR papers have been cycled for over 300 cycles, exhibiting a stable life cycle. Combined with LiCoO₂ nanowires, a full battery is produced with high energy density (386 Wh kg^?1), meeting requirements for high performance devices.     

Building Lithiophilic Ion‐Conduction Highways on Garnet‐Type Solid‐State Li+ Conductors

The integration of highly conductive solid‐state electrolytes (SSEs) into solid‐state cells is still a challenge mainly due to the high impedance existing at the electrolyte/electrode interface. Although solid‐state garnet‐based batteries have been successfully assembled with the assistance of an intermediate layer between the garnet and the Li metal anode, the slow discharging/charging rates of the batteries inhibits practical applications, which require much higher power densities. Here, a crystalline sulfonated‐covalent organic framework (COF) thin layer is grown on the garnet surface via a simple solution process. It not only significantly improves the lithiophilicity of garnet electrolytes via the lithiation of the COF layer with molten Li, but also creates effective Li⁺ diffusion “highways” between the garnet and the Li metal anode. As a result, the interfacial impedance of symmetric solid‐state Li cells is significantly decreased and the cells can be operated at high current densities up to 3 mA cm^?2, which is difficult to achieve with current interfacial modification technologies for SSEs. The solid‐state Li‐ion batteries using LiFePO₄ cathodes, Li anodes, and COF‐modified garnet electrolytes thus exhibit a significantly improved rate capability.     

Thermally Durable Lithium‐Ion Capacitors with High Energy Density from All Hydroxyapatite Nanowire‐Enabled Fire‐Resistant Electrodes and Separators

The reliability and durability of lithium‐ion capacitors (LICs) are severely hindered by the kinetic imbalance between capacitive and Faradaic electrodes. Efficient charge storage in LICs is still a huge challenge, particularly for thick electrodes with high mass loading, fast charge delivery, and harsh working conditions. Here, a unique thermally durable, stable LIC with high energy density from all‐inorganic hydroxyapatite nanowire (HAP NW)‐enabled electrodes and separators is reported. Namely, the LIC device is designed and constructed with the electron/ion dual highly conductive and fire‐resistant composite Li₄Ti₅O₁₂‐based anode and activated carbon‐based cathode, together with a thermal‐tolerant HAP NW separator. Despite the thick‐electrode configuration, the as‐fabricated all HAP NW‐enabled LIC exhibits much enhanced electrochemical kinetics and performance, especially at high current rates and temperatures. Long cycling lifetime and state‐of‐the‐art areal energy density (1.58 mWh cm^?2) at a high mass loading of 30 mg cm^?2 are achieved. Benefiting from the excellent fire resistance of HAP NWs, such an unusual LIC exhibits high thermal durability and can work over a wide range of temperatures from room temperature to 150 °C. Taking full advantage of synergistic configuration design, this work sets the stage for designing advanced LICs beyond the research of active materials.     

A Versatile Sn‐Substituted Argyrodite Sulfide Electrolyte for All‐Solid‐State Li Metal Batteries

Sulfide‐based solid‐state electrolytes (SSEs) for all‐solid‐state Li metal batteries (ASSLMBs) are attracting significant attention due to their high ionic conductivity, inherently soft properties, and decent mechanical strength. However, the poor incompatibility with Li metal and air sensitivity have hindered their application. Herein, the Sn (IV) substitution for P (V) in argyrodite sulfide Li₆PS₅I (LPSI) SSEs is reported, in the preparation of novel LPSI‐xSn SSEs (where x is the Sn substitution percentage). Appropriate aliovalent element substitutions with larger atomic radius (R_<Sn> > R_<P>) provides the optimized LPSI‐20Sn electrolyte with a 125 times higher ionic conductivity compared to that of the LPSI electrolyte. The high ionic conductivity of LPSI‐20Sn enables the rich I‐containing electrolyte to serve as a stabilized interlayer against Li metal in sulfide‐based ASSLMBs with outstanding cycling stability and rate capability. Most importantly, benefiting from the strong Sn–S bonding in Sn‐substituted electrolytes, the LPSI‐20Sn electrolyte shows excellent structural stability and improved air stability after exposure to O₂ and moisture. The versatile Sn substitution in argyrodite LPSI electrolytes is believed to provide a new and effective strategy to achieve Li metal‐compatible and air‐stable sulfide‐based SSEs for large‐scale applications.     

Perovskite Membranes with Vertically Aligned Microchannels for All‐Solid‐State Lithium Batteries

Perovskite‐type solid‐state electrolytes exhibit great potential for the development of all‐solid‐state lithium batteries due to their high Li‐ion conductivity (approaching 10^?3 S cm^?1), wide potential window, and excellent thermal/chemical stability. However, the large solid–solid interfacial resistance between perovskite electrolytes and electrode materials is still a great challenge that hinders the development of high‐performance all‐solid‐state lithium batteries. In this work, a perovskite‐type Li_0.34La_0.51TiO₃ (LLTO) membrane with vertically aligned microchannels is constructed by a phase‐inversion method. The 3D vertically aligned microchannel framework membrane enables more effective Li‐ion transport between the cathode and solid‐state electrolyte than a planar LLTO membrane. A significant decrease in the perovskite/cathode interfacial resistance, from 853 to 133 Ω cm², is observed. It is also demonstrated that full cells utilizing LLTO with vertically aligned microchannels as the electrolyte exhibit a high specific capacity and improved rate performance.     

Solid‐State Prelithiation Enables High‐Performance Li‐Al‐H Anode for Solid‐State Batteries

Lithium alanates exhibit high theoretical specific capacities and appropriate lithiation/delithiation potentials, but suffer from poor reversibility, cycling stability, and rate capability due to their sluggish kinetics and extensive side reactions. Herein, a novel and facile solid‐state prelithiation approach is proposed to in situ prepare a Li₃AlH₆‐Al nanocomposite from a short‐circuited electrochemical reaction between LiAlH₄ and Li with the help of fast electron and Li‐ion conductors (C and P6₃mc LiBH₄). This nanocomposite consists of dispersive Al nanograins and an amorphous Li₃AlH₆ matrix, which enables superior electrochemical performance in solid‐state cells, as much higher specific capacity (2266 mAh g^?1), Coulombic efficiency (88%), cycling stability (71% retention in the 100th cycle), and rate capability (1429 mAh g^?1 at 1 A g^?1) are achieved. In addition, this nanocomposite works well in the solid‐state full cell with LiCoO₂ cathode, demonstrating its promising application prospects. Mechanism analysis reveals that the dispersive Al nanograins and amorphous Li₃AlH₆ matrix can dramatically enhance the lithiation and delithiation kinetics without side reactions, which is mainly responsible for the excellent overall performance. Moreover, this solid‐state prelithiation approach is general and can also be applied to other Li‐poor electrode materials for further modification of their electrochemical behavior.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Lithiation‐Induced Dilation Mapping in a Lithium‐Ion Battery Electrode by 3D X‐Ray Microscopy and Digital Volume Correlation

Recent advances in high‐resolution 3D X‐ray computed tomography (CT) allow detailed, non‐destructive 3D structural mapping of a complete lithium‐ion battery. By repeated 3D image acquisition (time lapse CT imaging) these investigations of material microstructure are extended into the fourth dimension (time) to study structural changes of the device in operando. By digital volume correlation (DVC) of successive 3D images the dimensional changes taking place during charge cycling are quantified at the electrode level and at the Mn₂O₄ particle scale. After battery discharging, the extent of lithiation of the manganese (III/IV) oxide grains in the electrode is found to be a function of the distance from the battery terminal with grains closest to the electrode/current collector interface having the greatest expansion (≈30%) and grains furthest from the current collector and closest to the counter electrode showing negligible dilation. This implies that the discharge is limited by electrical conductivity. This new CT+DVC technique is widely applicable to the 3D exploration of the microstructural degradation processes for a range of energy materials including fuel cells, capacitors, catalysts, and ceramics.     

Ultrathin Bilayer of Graphite/SiO2 as Solid Interface for Reviving Li Metal Anode

Lithium metal anodes are expected to drive practical applications that require high energy‐density storage. However, the direct use of metallic lithium causes safety concerns, low rate capabilities, and poor cycling performance due to unstable solid electrolyte interphase (SEI) and undesired lithium dendrite growth. To address these issues, a radio frequency sputtered graphite‐SiO₂ ultrathin bilayer on a Li metal chips is demonstrated, for the first time, as an effective SEI layer. This leads to a dendrite free uniform Li deposition to achieve a stable voltage profile and outstanding long hours plating/stripping compared to the bare Li. Compared to a bare Li anode, the graphite‐SiO₂ bilayer modified Li anode coupled with lithium nickel cobalt manganese oxide cathode (NMC111) and lithium titanate shows improved capacity retention, higher capacity at higher rates, longer cycling stability, and lower voltage hysteresis. Graphite acts as an electrical bridge between the plated Li and Li electrode, which lowers the impedance and buffers the volume expansion during Li plating/stripping. Adding an ultrathin SiO₂ layer facilitates Li‐ion diffusion and lithiation/delithiation, provides higher electrolyte affinity, higher chemical stability, and higher Young's modulus to suppress the Li dendrite growth.