Carrier Transport and Recombination in Efficient “All‐Small‐Molecule” Solar Cells with the Nonfullerene Acceptor IDTBR

Reaching device efficiencies that can rival those of polymer‐fullerene Bulk Heterojunction (BHJ) solar cells (>10%) remains challenging with the “All‐Small‐Molecule” (All‐SM) approach, in part because of (i) the morphological limitations that prevail in the absence of polymer and (ii) the difficulty to raise and balance out carrier mobilities across the active layer. In this report, the authors show that blends of the SM donor DR3TBDTT (DR3) and the nonfullerene SM acceptor O‐IDTBR are conducive to “All‐SM” BHJ solar cells with high open‐circuit voltages (V_OC) >1.1 V and PCEs as high as 6.4% (avg. 6.1%) when the active layers are subjected to a post‐processing solvent vapor‐annealing (SVA) step with dimethyl disulfide (DMDS). Combining electron energy loss spectroscopy (EELS) analyses and systematic carrier recombination examinations, the authors show that SVA treatments with DMDS play a determining role in improving charge transport and reducing non‐geminate recombination for the DR3:O‐IDTBR system. Correlating the experimental results and device simulations, it is found that substantially higher BHJ solar cell efficiencies of >12% can be achieved if the IQE and carrier mobilities of the active layer are increased to >85% and >10^?4 cm² V^?1 s^?1, respectively, while suppressing the recombination rate constant k to <10^?12 cm³ s^?1.     

Thieno[3,4‐c]Pyrrole‐4,6‐Dione‐Based Polymer Acceptors for High Open‐Circuit Voltage All‐Polymer Solar Cells

While polymer acceptors are promising fullerene alternatives in the fabrication of efficient bulk heterojunction (BHJ) solar cells, the range of efficient material systems relevant to the “all‐polymer” BHJ concept remains narrow, and currently limits the perspectives to meet the 10% efficiency threshold in all‐polymer solar cells. This report examines two polymer acceptor analogs composed of thieno[3,4‐c ]pyrrole‐4,6‐dione (TPD) and 3,4‐difluorothiophene ([2F]T) motifs, and their BHJ solar cell performance pattern with a low‐bandgap polymer donor commonly used with fullerenes (PBDT‐TS1; taken as a model system). In this material set, the introduction of a third electron‐deficient motif, namely 2,1,3‐benzothiadiazole (BT), is shown to (i) significantly narrow the optical gap (E _opt) of the corresponding polymer (by ≈0.2 eV) and (ii) improve the electron mobility of the polymer by over two orders of magnitude in BHJ solar cells. In turn, the narrow‐gap P2TPDBT[2F]T analog (E _opt = 1.7 eV) used as fullerene alternative yields high open‐circuit voltages (V _OC) of ≈1.0 V, notable short‐circuit current values (J _SC) of ≈11.0 mA cm⁻², and power conversion efficiencies (PCEs) nearing 5% in all‐polymer BHJ solar cells. P2TPDBT[2F]T paves the way to a new, promising class of polymer acceptor candidates.     

Polymer Main‐Chain Substitution Effects on the Efficiency of Nonfullerene BHJ Solar Cells

“Nonfullerene” acceptors are proving effective in bulk heterojunction (BHJ) solar cells when paired with selected polymer donors. However, the principles that guide the selection of adequate polymer donors for high‐efficiency BHJ solar cells with nonfullerene acceptors remain a matter of some debate and, while polymer main‐chain substitutions may have a direct influence on the donor–acceptor interplay, those effects should be examined and correlated with BHJ device performance patterns. This report examines a set of wide‐bandgap polymer donor analogues composed of benzo[1,2‐b:4,5‐b′]dithiophene (BDT), and thienyl ([2H]T) or 3,4‐difluorothiophene ([2F]T) motifs, and their BHJ device performance pattern with the nonfullerene acceptor “ITIC”. Studies show that the fluorine‐ and ring‐substituted derivative PBDT(T)[2F]T largely outperforms its other two polymer donor counterparts, reaching power conversion efficiencies as high as 9.8%. Combining several characterization techniques, the gradual device performance improvements observed on swapping PBDT[2H]T for PBDT[2F]T, and then for PBDT(T)[2F]T, are found to result from (i) notably improved charge generation and collection efficiencies (estimated as ≈60%, 80%, and 90%, respectively), and (ii) reduced geminate recombination (being suppressed from ≈30%, 25% to 10%) and bimolecular recombination (inferred from recombination rate constant comparisons). These examinations will have broader implications for further studies on the optimization of BHJ solar cell efficiencies with polymer donors and a wider range of nonfullerene acceptors.     

Higher Mobility and Carrier Lifetimes in Solution‐Processable Small‐Molecule Ternary Solar Cells with 11% Efficiency

Solution‐processed small molecule (SM) solar cells have the prospect to outperform their polymer‐fullerene counterparts. Considering that both SM donors/acceptors absorb in visible spectral range, higher expected photocurrents should in principle translate into higher power conversion efficiencies (PCEs). However, limited bulk‐heterojunction (BHJ) charge carrier mobility (<10^‐4 cm² V^‐1 s^‐1) and carrier lifetimes (<1 µs) often impose active layer thickness constraints on BHJ devices (≈100 nm), limiting external quantum efficiencies (EQEs) and photocurrent, and making large‐scale processing techniques particularly challenging. In this report, it is shown that ternary BHJs composed of the SM donor DR3TBDTT (DR3), the SM acceptor ICC6 and the fullerene acceptor PC₇₁BM can be used to achieve SM‐based ternary BHJ solar cells with active layer thicknesses >200 nm and PCEs nearing 11%. The examinations show that these remarkable figures are the result of i) significantly improved electron mobility (8.2 × 10^‐4 cm² V^‐1 s^‐1), ii) longer carrier lifetimes (2.4 µs), and iii) reduced geminate recombination within BHJ active layers to which PC₇₁BM has been added as ternary component. Optically thick (up to ≈500 nm) devices are shown to maintain PCEs >8%, and optimized DR3:ICC6:PC₇₁BM solar cells demonstrate long‐term shelf stability (dark) for >1000 h, in 55% humidity air environment.     

Mixed Domains Enhance Charge Generation and Extraction in Bulk‐Heterojunction Solar Cells with Small‐Molecule Donors

The interplay between nanomorphology and efficiency of polymer‐fullerene bulk‐heterojunction (BHJ) solar cells has been the subject of intense research, but the generality of these concepts for small‐molecule (SM) BHJs remains unclear. Here, the relation between performance; charge generation, recombination, and extraction dynamics; and nanomorphology achievable with two SM donors benzo[1,2‐b:4,5‐b]dithiophene‐pyrido[3,4‐b]‐pyrazine BDT(PPTh₂)₂, namely SM1 and SM2, differing by their side‐chains, are examined as a function of solution additive composition. The results show that the additive 1,8‐diiodooctane acts as a plasticizer in the blends, increases domain size, and promotes ordering/crystallinity. Surprisingly, the system with high domain purity (SM1) exhibits both poor exciton harvesting and severe charge trapping, alleviated only slightly with increased crystallinity. In contrast, the system consisting of mixed domains and lower crystallinity (SM2) shows both excellent exciton harvesting and low charge recombination losses. Importantly, the onset of large, pure crystallites in the latter (SM2) system reduces efficiency, pointing to possible differences in the ideal morphologies for SM‐based BHJ solar cells compared with polymer‐fullerene devices. In polymer‐based systems, tie chains between pure polymer crystals establish a continuous charge transport network, whereas SM‐based active layers may in some cases require mixed domains that enable both aggregation and charge percolation to the electrodes.     

Bandgap Narrowing in Non‐Fullerene Acceptors: Single Atom Substitution Leads to High Optoelectronic Response Beyond 1000 nm

Two narrow bandgap non‐fullerene acceptors (NBG‐NFAs), namely, COTIC‐4F and SiOTIC‐4F, are designed and synthesized for the fabrication of efficient near‐infrared organic solar cells (OSCs). The chemical structures of the NBG‐NFAs contain a D′‐D‐D′ electron‐rich internal core based on a cyclopentadithiophene (or dithienosilole) (D) and alkoxythienyl (D′) core, end‐capped with the highly electron‐deficient unit 2‐(5,6‐difluoro‐3‐oxo‐2,3‐dihydro‐1H‐inden‐1‐ylidene)malononitrile (A), ultimately providing a A‐D′‐D‐D′‐A molecular configuration that enhances the intramolecular charge transfer characteristics of the excited states. One can thereby reduce the optical bandgap (E_g^opt) to as low as ≈1.10 eV, one of the smallest values for NFAs reported to date. In bulk‐heterojunction (BHJ) OSCs, NBG‐NFA blends with the polymer donor PTB7‐Th yield power conversion efficiencies (PCE) of up to 9.0%, which is particularly high when compared against a range of NBG BHJ blends. Most significantly, it is found that, despite the small energy loss (E_g^opt ? eV_OC) of 0.52 eV, the PTB7‐Th/NBG‐NFA bulk heterojunction blends can yield short‐circuit current densities of up to 22.8 mA cm^?2, suggesting that the design and application of NBG‐NFA materials have substantial potential to further improve the PCE of OSCs.     

Donor‐Acceptor Interfacial Interactions Dominate Device Performance in Hybrid P3HT‐ZnO Nanowire‐Array Solar Cells

The adsorption of self‐assembled monolayers (SAMs) on metal oxide surfaces is a promising route to control electronic characteristics and surface wettability. Here, arylphosphonic acid derivatives are used to modulate the surface properties of vertically oriented ZnO nanowire arrays. Arylphosphonate‐functionalized ZnO nanowires are incorporated into hybrid organic‐inorganic solar cells in which infiltrated poly(3‐hexylthiophene) (P3HT) serves as the polymer donor. Strong correlations between device short‐circuit current density (J _sc) and power conversion efficiencies (PCEs) with ZnO surface functionalization species are observed and a weak correlation in the open‐circuit voltage (V _oc) is observed. Inverted solar cells fabricated with these treated interfaces exhibit PCEs as high as 2.1%, primarily due to improvements in J _sc. Analogous devices using untreated ZnO arrays having efficiencies of 1.6%. The enhancement in J _sc is attributed to surface passivation of ZnO by SAMs and enhanced wettability from P3HT, which improve charge transfer and reduce carrier recombination at the organic‐inorganic interface in the solar cells.     

The Importance of Fullerene Percolation in the Mixed Regions of Polymer–Fullerene Bulk Heterojunction Solar Cells

Most optimized donor‐acceptor (D‐A) polymer bulk heterojunction (BHJ) solar cells have active layers too thin to absorb greater than ～80% of incident photons with energies above the polymer's band gap. If the thickness of these devices could be increased without sacrificing internal quantum efficiency, the device power conversion efficiency (PCE) could be significantly enhanced. We examine the device characteristics of BHJ solar cells based on poly(di(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐octylthieno[3,4‐c]pyrrole‐4,6‐dione) (PBDTTPD) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) with 7.3% PCE and find that bimolecular recombination limits the active layer thickness of these devices. Thermal annealing does not mitigate these bimolecular recombination losses and drastically decreases the PCE of PBDTTPD BHJ solar cells. We characterize the morphology of these BHJs before and after thermal annealing and determine that thermal annealing drastically reduces the concentration of PCBM in the mixed regions, which consist of PCBM dispersed in the amorphous portions of PBDTTPD. Decreasing the concentration of PCBM may reduce the number of percolating electron transport pathways within these mixed regions and create morphological electron traps that enhance charge‐carrier recombination and limit device quantum efficiency. These findings suggest that (i) the concentration of PCBM in the mixed regions of polymer BHJs must be above the PCBM percolation threshold in order to attain high solar cell internal quantum efficiency, and (ii) novel processing techniques, which improve polymer hole mobility while maintaining PCBM percolation within the mixed regions, should be developed in order to limit bimolecular recombination losses in optically thick devices and maximize the PCE of polymer BHJ solar cells.     

Nongeminate Recombination in Planar and Bulk Heterojunction Organic Solar Cells

Nongeminate recombination in organic solar cells based on copper phthalocyanine (CuPc) and C₆₀ is investigated. Two device architectures, the planar heterojunction (PHJ) and the bulk heterojunction (BHJ), are directly compared in view of differences in charge carrier decay dynamics. A combination of transient photovoltage (TPV) experiments, yielding the small perturbation charge carrier lifetime, and charge extraction measurements, providing the charge carrier density is applied. In organic solar cells, charge photogeneration and recombination primarily occur at the donor–acceptor heterointerface. Whereas the BHJ can often be approximated by an effective medium due to rather small scale phase separation, the PHJ has a well defined two‐dimensional heterointerface. In order to study nongeminate recombination dynamics in PHJ devices the charge accumulation at this interface is most relavent. As only the spatially averaged carrier concentration can be determined from extraction techniques, the charge carrier density at the interface n_int is derived from the open circuit voltage. Comparing the experimental results with macroscopic device simulation, the differences of recombination and charge carrier densities in CuPc:C₆₀ PHJ and BHJ devices are discussed with respect to the device performance. The open circuit voltage of BHJ is larger than for PHJ at low light intensities, but at 0.3 sun the situation is reversed: here, the PHJ can finally take advantage of its generally longer charge carrier lifetimes, as the active recombination region is smaller.     

Charge‐Carrier Mobility Requirements for Bulk Heterojunction Solar Cells with High Fill Factor and External Quantum Efficiency >90%

To increase the efficiency of bulk heterojunction (BHJ) solar cells beyond 15%, 300 nm thick devices with 0.8 fill factor (FF) and external quantum efficiency (EQE) >90% are likely needed. This work demonstrates that numerical device simulators are a powerful tool for investigating charge‐carrier transport in BHJ devices and are useful for rapidly determining what semiconductor pro­perties are needed to reach these performance milestones. The electron and hole mobility in a BHJ must be ≈10^?2 cm² V^?1 s^?1 in order to attain a 0.8 FF in a 300 nm thick device with the recombination rate constant of poly(3‐hexyl­thiophene):[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM). Thus, the hole mobility of donor polymers needs to increase from ≈10^?4 to ≈10^?2 cm² V^?1 s^?1 in order to significantly improve device performance. Furthermore, the charge‐carrier mobility required for high FF is directly proportional to the BHJ recombination rate constant, which demonstrates that decreasing the recombination rate constant could dramatically improve the efficiency of optically thick devices. These findings suggest that researchers should prioritize improving charge‐carrier mobility when synthesizing new materials for BHJ solar cells and highlight that they should aim to understand what factors affect the recombination rate constant in these devices.     

Spatial Distribution Recast for Organic Bulk Heterojunctions for High‐Performance All‐Inorganic Perovskite/Organic Integrated Solar Cells

All‐inorganic CsPbIBr₂ perovskite solar cells (pero‐SCs) exhibit excellent overall stability, but their power conversion efficiencies (PCEs) are greatly limited by their wide bandgaps. Integrated solar cells (ISCs) are considered to be an emergent technology that could extend their photoresponse by directly stacking two distinct photoactive layers with complementary bandgaps. However, rising photocurrents always sacrifice other photovoltaic parameters, thereby leading to an unsatisfactory PCE. Here, a recast strategy is proposed to optimize the spatial distribution components of low‐bandgap organic bulk‐heterojunction (BHJ) film, and is combined with an all‐inorganic perovskite to construct perovskite/BHJ ISCs. With this strategy, the integrated perovskite/BHJ film with a top‐enriched donor‐material spatial distribution is shown to effectively improve ambipolar charge transport behavior and suppress charge carrier recombination. For the first time, the ISC is not only significantly extended and enhanced the photoresponse achieving a 20% increase in current density, but also exhibits a high open‐circuit voltage and fill factor at the same time. As a result, a record PCE of 11.08% based on CsPbIBr₂ pero‐SCs is realized; it simultaneously shows excellent long‐term stability against heat and ultraviolet light.     

Highly Efficient Aqueous‐Processed Hybrid Solar Cells: Control Depletion Region and Improve Carrier Extraction

Environmental friendly aqueous‐processed solar cells have become one of the most promising candidates for the next‐generation photovoltaic devices. Researchers have made lots of progress in designing active materials with novel structures, manipulating the defects in active materials, optimizing device architecture, etc. However, it has long been a challenge to control the width of the depletion region and enhance carrier extraction ability. Fabrication of a thick bulk heterojunction (BHJ) film is an effective strategy to address these issues but difficult to realize. Herein, the thicker BHJ film of ZnO:CdTe is successfully fabricated and incorporated into CdTe‐poly(p‐phenylenevinylene) hybrid solar cells. As expected, this BHJ film enhances light absorption, extends the width of the depletion region, prolongs carrier lifetime, and promotes carrier extraction ability. Moreover, the electron transport layer of sol–gel ZnO with excellent transmittance and electrical conductivity boosts electron generation, transport, and injection, which further improves the device performance. As a result, the highest short current density (J_sc) of 19.5 mA cm^?2, power conversion efficiency of 6.51%, and the widest depletion region (177 nm) are obtained in aqueous‐processed hybrid solar cells.     

Interplay Between Side Chain Pattern,Polymer Aggregation,and Charge Carrier Dynamics in PBDTTPD:PCBM Bulk‐Heterojunction Solar Cells

Poly(benzo[1,2‐b:4,5‐b′]dithiophene–alt–thieno[3,4‐c]pyrrole‐4,6‐dione) (PBDTTPD) polymer donors with linear side‐chains yield bulk‐heterojunction (BHJ) solar cell power conversion efficiencies (PCEs) of about 4% with phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as the acceptor, while a PBDTTPD polymer with a combination of branched and linear substituents yields a doubling of the PCE to 8%. Using transient optical spectroscopy it is shown that while the exciton dissociation and ultrafast charge generation steps are not strongly affected by the side chain modifications, the polymer with branched side chains exhibits a decreased rate of nongeminate recombination and a lower fraction of sub‐nanosecond geminate recombination. In turn the yield of long‐lived charge carriers increases, resulting in a 33% increase in short circuit current (J _sc). In parallel, the two polymers show distinct grazing incidence X‐ray scattering spectra indicative of the presence of stacks with different orientation patterns in optimized thin‐film BHJ devices. Independent of the packing pattern the spectroscopic data also reveals the existence of polymer aggregates in the pristine polymer films as well as in both blends which trap excitons and hinder their dissociation.     

Controlling Solution‐Phase Polymer Aggregation with Molecular Weight and Solvent Additives to Optimize Polymer‐Fullerene Bulk Heterojunction Solar Cells

The bulk heterojunction (BHJ) solar cell performance of many polymers depends on the polymer molecular weight (M _n) and the solvent additive(s) used for solution processing. However, the mechanism that causes these dependencies is not well understood. This work determines how M _n and solvent additives affect the performance of BHJ solar cells made with the polymer poly(di(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐octylthieno[3,4‐c]pyrrole‐4,6‐dione) (PBDTTPD). Low M _n PBDTTPD devices have exceedingly large fullerene‐rich domains, which cause extensive charge‐carrier recombination. Increasing the M _n of PBDTTPD decreases the size of these domains and significantly improves device performance. PBDTTPD aggregation in solution affects the size of the fullerene‐rich domains and this effect is linked to the dependency of PBDTTPD solubility on M _n. Due to its poor solubility high M _n PBDTTPD quickly forms a fibrillar polymer network during spin‐casting and this network acts as a template that prevents large‐scale phase separation. Furthermore, processing low M _n PBDTTPD devices with a solvent additive improves device performance by inducing polymer aggregation in solution and preventing large fullerene‐rich domains from forming. These findings highlight that polymer aggregation in solution plays a significant role in determining the morphology and performance of BHJ solar cells.     

Dithienogermole‐Containing Small‐Molecule Solar Cells with 7.3% Efficiency: In‐Depth Study on the Effects of Heteroatom Substitution of Si with Ge

Two small molecule donor materials (DTGe(FBTTh₂)₂ and DTGe(FBTBFu)₂) incorporating the dithienogermole (DTGe) moiety with fluorobenzothiadiazole (FBT) and bithiophene (Th₂) or benzofuran (BFu) end‐capping groups are synthesized and their properties as donor materials in small molecule bulk heterojunction type (BHJ) solar cells are investigated. The DTGe(FBTTh₂)₂ with Th₂ end groups shows outstanding solar cell characteristics with efficiencies up to 6.4% using a standard BHJ architecture and 7.3% using a ZnO optical spacer, while the BFu end‐capped DTGe(FBTBFu)₂ has slightly wider band gaps and yields slightly higher open circuit voltage (V_OC) at the expense of short circuit current (J_SC) and fill factor (FF). In this study, the DTGe‐based molecules are systematically compared to the dithienosilole (DTSi)‐based analogues, which are currently among the highest power conversion efficiency (PCE) small molecule solar cell donor materials known. The J_SC produced by the DTGe molecule is found to be similar to, or slightly higher than the Si analogue, despite similar absorption characteristics, however, the PCE is similar to the Si analogues due to small decreases in V_OC and FF. This report marks the first small molecule BHJ based on a Ge‐containing heterocycle with PCE over 7%.     

Strategic Halogen Substitution to Enable High‐Performance Small‐Molecule‐Based Tandem Solar Cell with over 15% Efficiency

Small molecules have been recently highlighted as active materials owing to their facile synthesisis method, well‐defined molecular structure, and highly reproducible performance. In particular, optimizing bulk heterojunction (BHJ) morphologies is important to achieving high performance in solution‐processable small molecule solar cells (SM‐SCs). Herein, a series of benzodithiophene‐based active materials with different halogen atoms substituted at the end‐group, are reported, as well as how these halogen atoms affect the morphology of BHJ architectures through microstructure analyses. Materials with chlorine atoms show a well‐mixed morphology and interpenetrating networks when blended with [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester, facilitating effective charge transportation. This controlled morphology helps attain excellent performance with a power conversion efficiency (PCE) of 10.5% and a highest fill factor of 78.0% without additives. In addition, it can be applied to two‐terminal (2T)‐tandem solar cells, attaining an outstanding PCE of up to 15.1% with complementary absorption in the field of the 2T‐tandem solar cells introducing the SM‐SCs. These results suggest that tailoring interactions with halogen atoms is an effective way to control BHJ architectures, thereby achieving remarkable performance in SM‐SCs.     

Effect of Molecular Orientation of Donor Polymers on Charge Generation and Photovoltaic Properties in Bulk Heterojunction All‐Polymer Solar Cells

All‐polymer solar cells (all‐PSCs) utilizing p‐type polymers as electron‐donors and n ‐typepolymers as electron‐acceptors have attracted a great deal of attention, and their efficiencies have been improved considerably. Here, five polymer donors with different molecular orientations are synthesized by random copolymerization of 5‐fluoro‐2,1,3‐benzothiadiazole with different relative amounts of 2,2′‐bithiophene (2T) and dithieno[3,2‐b;2′,3′‐d]thiophene (DTT). Solar cells are prepared by blending the polymer donors with a naphthalene diimide‐based polymer acceptor (PNDI) or a [6,6]‐phenyl C₇₁‐butyric acid methyl ester (PC₇₁BM) acceptor and their morphologies and crystallinity as well as optoelectronic, charge‐transport and photovoltaic properties are studied. Interestingly, charge generation in the solar cells is found to show higher dependence on the crystal orientation of the donor polymer for the PNDI‐based all‐PSCs than for the conventional PC₇₁BM‐based PSCs. As the population of face‐on‐oriented crystallites of the donor increased in PNDI‐based PSC, the short‐circuit current density (J_SC) and external quantum efficiency of the devices are found to significantly improve. Consequently, device efficiency was enhanced of all‐PSC from 3.11% to 6.01%. The study reveals that producing the same crystal orientation between the polymer donor and acceptor (face‐on/face‐on) is important in all‐PSCs because they provide efficient charge transfer at the donor/acceptor interface.     

A Thieno[3,2‐c]Isoquinolin‐5(4H)‐One Building Block for Efficient Thick‐Film Solar Cells

An aromatic lactam acceptor unit, thieno[3,2‐c]isoquinolin‐5(4H)‐one (TIQ), is developed. Compared with its analogues, dithieno[3,2‐b:2′,3′‐d]pyridin‐5(4H)‐one (DTP) and phenanthridin‐6(5H)‐one (PN), TIQ shows its advantage in constructing donor–acceptor (D–A) copolymers for efficient solar cells. TIQ‐based D–A copolymer PTIQ4TFBT delivers a power conversion efficiency (PCE) of 10.16% in polymer:fullerene solar cells, while those based on DTP and PN copolymers, PDTP4TFBT and PPN4TFBT, afford PCEs around 8.5%. The higher performance of PTIQ4TFBT:PC₇₁BM solar cells originates from enhanced short‐circuit current density (J_sc) and fill factor (FF), because of favorable morphology, less bimolecular recombination, and balanced charge transport in the active layer. Moreover, the performance for PTIQ4TFBT:PC₇₁BM solar cells is less sensitive to active layer thickness than PDTP4TFBT:PC₇₁BM and PPN4TFBT:PC₇₁BM solar cells. Over 8% PCEs can be obtained from PTIQ4TFBT:PC₇₁BM solar cells when the active layer thickness is over 500 nm.     

Reducing Voltage Losses in Cascade Organic Solar Cells while Maintaining High External Quantum Efficiencies

High photon energy losses limit the open‐circuit voltage (V_OC) and power conversion efficiency of organic solar cells (OSCs). In this work, an optimization route is presented which increases the V_OC by reducing the interfacial area between donor (D) and acceptor (A). This optimization route concerns a cascade device architecture in which the introduction of discontinuous interlayers between alpha‐sexithiophene (α‐6T) (D) and chloroboron subnaphthalocyanine (SubNc) (A) increases the V_OC of an α‐6T/SubNc/SubPc fullerene‐free cascade OSC from 0.98 V to 1.16 V. This increase of 0.18 V is attributed solely to the suppression of nonradiative recombination at the D–A interface. By accurately measuring the optical gap (E_opt) and the energy of the charge‐transfer state (E_CT) of the studied OSC, a detailed analysis of the overall voltage losses is performed. E_opt – qV_OC losses of 0.58 eV, which are among the lowest observed for OSCs, are obtained. Most importantly, for the V_OC‐optimized devices, the low‐energy (700 nm) external quantum efficiency (EQE) peak remains high at 79%, despite a minimal driving force for charge separation of less than 10 meV. This work shows that low‐voltage losses can be combined with a high EQE in organic photovoltaic devices.     

Vacuum‐Assisted Growth of Low‐Bandgap Thin Films (FA0.8MA0.2Sn0.5Pb0.5I3) for All‐Perovskite Tandem Solar Cells

All‐perovskite multijunction photovoltaics, combining a wide‐bandgap (WBG) perovskite top solar cell (E_G ≈1.6–1.8 eV) with a low‐bandgap (LBG) perovskite bottom solar cell (E_G < 1.3 eV), promise power conversion efficiencies (PCEs) >33%. While the research on WBG perovskite solar cells has advanced rapidly over the past decade, LBG perovskite solar cells lack PCE as well as stability. In this work, vacuum‐assisted growth control (VAGC) of solution‐processed LBG perovskite thin films based on mixed Sn–Pb perovskite compositions is reported. The reported perovskite thin films processed by VAGC exhibit large columnar crystals. Compared to the well‐established processing of LBG perovskites via antisolvent deposition, the VAGC approach results in a significantly enhanced charge‐carrier lifetime. The improved optoelectronic characteristics enable high‐performance LBG perovskite solar cells (1.27 eV) with PCEs up to 18.2% as well as very efficient four‐terminal all‐perovskite tandem solar cells with PCEs up to 23%. Moreover, VAGC leads to promising reproducibility and potential in the fabrication of larger active‐area solar cells up to 1 cm².