Ultrafast All‐Solid‐State Coaxial Asymmetric Fiber Supercapacitors with a High Volumetric Energy Density

Fiber‐supercapacitors (FSCs) are promising energy storage devices that can complement or even replace microbatteries in miniaturized portable and wearable electronics. Currently, a major challenge for FSCs is achieving ultrahigh volumetric energy and power densities simultaneously, especially when the charge/discharge rates exceed 1 V s^?1. Herein, an Au‐nanoparticle‐doped‐MnO_x@CoNi‐alloy@carbon‐nanotube (Au–MnO_x@CoNi@CNT) core/shell nanocomposite fiber electrode is designed, aiming to boost its charge/discharge rate by taking advantage of the superconductive CoNi alloy network and the greatly enhanced conductivity of the Au doped MnO_x active materials. An all‐solid‐state coaxial asymmetric FSC (CAFSC) prototype device made by wrapping this fiber with a holey graphene paper (HGP) exhibits excellent performance at rates up to 10 V s^?1, which is the highest charge rate demonstrated so far for FSCs based on pseudocapacitive materials. Furthermore, our fully packaged CAFSC delivers a volumetric energy density of ≈15.1 mW h cm^?3, while simultaneously maintaining a high power density of 7.28 W cm^?3 as well as a long cycle life (90% retention after 10 000 cycles). This value is the highest among all reported FSCs, even better than that of a typical 4 V/500 µA h thin‐film lithium battery.     

Graphitic Petal Electrodes for All‐Solid‐State Flexible Supercapacitors

The charge storage characteristics of a composite nanoarchitecture with a highly functional 3D morphology are reported. The electrodes are formed by the electropolymerization of aniline monomers into a nanometer‐thick polyaniline (PANI) film that conformally coats graphitic petals (GPs) grown by microwave plasma chemical vapor deposition (MPCVD) on conductive carbon cloth (CC). The hybrid CC/GPs/PANI electrodes yield results near the theoretical maximum capacitance for PANI of 2000 F g^?1 (based on PANI mass) and a large area‐normalized specific capacitance of ≈2.6 F cm^?2 (equivalent to a volumetric capacitance of ≈230 F cm^?3) at a low current density of 1 A g^?1 (based on PANI mass). The specific capacitances remain above 1200 F g^?1 (based on PANI mass) for currents up to 100 A g^?1 with correspondingly high area‐normalized values. The hybrid electrodes also exhibit a high rate capability with an energy density of 110 Wh kg^?1 and a maximum power density of 265 kW kg^?1 at a current density of 100 A g^?1. Long‐term cyclic stability is good (≈7% loss of initial capacitance after 2000 cycles), with coulombic efficiencies >99%. Moreover, prototype all‐solid‐state flexible supercapacitors fabricated from these hybrid electrodes exhibit excellent energy storage performance.     

Flexible and Wearable All‐Solid‐State Supercapacitors with Ultrahigh Energy Density Based on a Carbon Fiber Fabric Electrode

Wearable textile energy storage systems are rapidly growing, but obtaining carbon fiber fabric electrodes with both high capacitances to provide a high energy density and mechanical strength to allow the material to be weaved or knitted into desired devices remains challenging. In this work, N/O‐enriched carbon cloth with a large surface area and the desired pore volume is fabricated. An electrochemical oxidation method is used to modify the surface chemistry through incorporation of electrochemical active functional groups to the carbon surface and to further increase the specific surface area and the pore volume of the carbon cloth. The resulting carbon cloth electrode presents excellent electrochemical properties, including ultrahigh areal capacitance with good rate ability and cycling stability. Furthermore, the fabricated symmetric supercapacitors with a 2 V stable voltage window deliver ultrahigh energy densities (6.8 mW h cm^?3 for fiber‐shaped samples and 9.4 mW h cm^?3 for fabric samples) and exhibit excellent flexibility. The fabric supercapacitors are further tested in a belt‐shaped device as a watchband to power an electronic watch for ≈9 h, in a heart‐shaped logo to supply power for ≈1 h and in a safety light that functions for ≈1 h, indicating various promising applications of these supercapacitors.     

High Performance,Flexible, Solid‐State Supercapacitors Based on a Renewable and Biodegradable Mesoporous Cellulose Membrane

A flexible, transparent, and renewable mesoporous cellulose membrane (mCel‐membrane) featuring uniform mesopores of ≈24.7 nm and high porosity of 71.78% is prepared via a facile and scalable solution‐phase inversion process. KOH‐saturated mCel‐membrane as a polymer electrolyte demonstrates a high electrolyte retention of 451.2 wt%, a high ionic conductivity of 0.325 S cm^?1, and excellent mechanical flexibility and robustness. A solid‐state electric double layer capacitor (EDLC) using activated carbon as electrodes, the KOH‐saturated mCel‐membrane as a polymer electrolyte exhibits a high capacitance of 110 F g^?1 at 1.0 A g^?1, and long cycling life of 10 000 cycles with 84.7% capacitance retention. Moreover, a highly integrated planar‐type micro‐supercapacitor (MSC) can be facilely fabricated by directly depositing the electrode materials on the mCel‐membrane‐based polymer electrolyte without using complicated devices. The resulting MSC exhibits a high areal capacitance of 153.34 mF cm^?2 and volumetric capacitance of 191.66 F cm^?3 at 10 mV s^?1, representing one of the highest values among all carbon‐based MSC devices. These findings suggest that the developed renewable, flexible, mesoporous cellulose membrane holds great promise in the practical applications of flexible, solid‐state, portable energy storage devices that are not limited to supercapacitors.     

Interconnected Frameworks with a Sandwiched Porous Carbon Layer/Graphene Hybrids for Supercapacitors with High Gravimetric and Volumetric Performances

A facile approach to synthesize porous disordered carbon layers as energy storage units coating on graphene sheets to form interconnected frameworks by one‐step pyrolysis of the mixture of graphene oxide/polyaniline and KOH is presented. As effective energy storage units, these porous carbon layers play an important role in enhancing the electrochemical performances. The obtained porous carbon material exhibits a high specific surface area (2927 m² g^?1), hierarchical interconnected pores, moderate pore volume (1.78 cm³ g^?1), short ion diffusion paths, and a high nitrogen level (6 at%). It displays both unparalleled gravimetric (481 F g^?1) and outstanding volumetric capacitance (212 F cm^?3) in an aqueous electrolyte. More importantly, the assembled symmetrical supercapacitor delivers not only high gravimetric (25.7 Wh kg^?1 based on total mass of electroactive materials) but also high volumetric energy densities (11.3 Wh L^?1) in an aqueous electrolyte. Furthermore, the assembled asymmetric supercapacitor yields a maximum energy density up to 88 Wh kg^?1, which is, to the best of our knowledge, the highest value so far reported for carbon//MnO₂ asymmetric supercapacitors in aqueous electrolytes. Therefore, this novel carbon material holds great promise for potential applications in energy‐related technological fields.     

All‐Solid‐State On‐Chip Supercapacitors Based on Free‐Standing 4H‐SiC Nanowire Arrays

All‐solid‐state on‐chip SiC supercapacitors (SCs) based on free‐standing SiC nanowire arrays (NWAs) are reported. In comparison to the widely used technique based on the interdigitated fingers, the present strategy can be much more facile for constructing on‐chip SCs devices, which is directly sandwiched with a solid electrolyte layer between two pieces of SiC NWAs film without any substrate. The mass loading of active materials of on‐chip SiC SCs can be up to ≈5.6 mg cm^?2, and the total device thickness is limited in ≈40 µm. The specific area energy and power densities of the SCs device reach 5.24 µWh cm^?2 and 11.2 mW cm^?2, and their specific volume energy and power densities run up to 1.31 mWh cm^–3 and 2.8 W cm^?3, respectively, which are two orders of magnitude higher than those of state‐of‐the‐art SiC‐based SCs, and also much higher than those of other solid‐state carbon‐based SCs ever reported. Furthermore, such on‐chip SCs exhibit superior rate capability and robust stability with over 94% capacitance retention after 10 000 cycles at a scan rate of 100 mV s^?1, representing their high performance in all merits.     

All‐Solid‐State Fiber Supercapacitors with Ultrahigh Volumetric Energy Density and Outstanding Flexibility

Fiber supercapacitors (FSCs) represent a promising class of energy storage devices that can complement or even replace microbatteries in miniaturized portable and wearable electronics. One of their main limitations, however, is the low volumetric energy density when compared with those of rechargeable batteries. Considering the energy density of FSC is proportional to CV² (E = 1/2 CV², where C is the capacitance and V is the operating voltage), one would explore high operating voltage as an effective strategy to promote the volumetric energy density. In the present work, an all‐solid‐state asymmetric FSC (AFSC) with a maximum operating voltage of 3.5 V is successfully achieved, by employing an ionic liquid (IL) incorporated gel‐polymer as the electrolyte (EMIMTFSI/PVDF‐HFP). The optimized AFSC is based on MnO_x@TiN nanowires@carbon nanotube (NWs@CNT) fiber as the positive electrode and C@TiN NWs@CNT fiber as the negative electrode, which gives rise to an ultrahigh stack volumetric energy density of 61.2 mW h cm^?3, being even comparable to those of commercially planar lead‐acid batteries (50–90 mW h cm^?3), and an excellent flexibility of 92.7% retention after 1000 blending cycles at 90°. The demonstration of employing the ILs‐based electrolyte opens up new opportunities to fabricate high‐performance flexible AFSC for future portable and wearable electronic devices.     

Free‐Standing 3D Nanoporous Duct‐Like and Hierarchical Nanoporous Graphene Films for Micron‐Level Flexible Solid‐State Asymmetric Supercapacitors

High energy density and power density within a limited volume of flexible solid‐state supercapacitors are highly desirable for practical applications. Here, free‐standing high‐quality 3D nanoporous duct‐like graphene (3D‐DG) films are fabricated with high flexibility and robustness as the backbones to deposit flower‐like MnO₂ nanosheets (3D‐DG@MnO₂). The 3D‐DG is the ideal support for the deposition of large amount of active materials because of its large surface area, appropriate pore structure, and negligible volume compared with other kinds of carbon backbones. Moreover, the 3D‐DG preserve the distinctive 2D coherent electronic properties of graphene, in which charge carriers move rapidly with a small resistance through the high‐quality and continuous chemical vapor deposition‐grown graphene building blocks, which results in a high rate performance. Marvelously, ultrathin (≈50 μm) flexible solid‐state asymmetric supercapacitors (ASCs) using 3D‐DG@MnO₂ as the positive electrode and 3D hierarchical nanoporous graphene films as the negative electrode display ultrahigh volumetric energy density (28.2 mW h cm^?3) and power density (55.7 W cm^?3) at 2.0 V. Furthermore, as‐prepared ASCs show high cycle stability clearly demonstrating their broad applications as power supplies in wearable electronic devices.     

Aqueous Solution‐Processable Small Molecular Metal‐Chelate Complex Electrolyte for Flexible All‐Solid State Energy Storage Devices

A small molecular metal‐chelate complex, tris(8‐hydroxyquinoline‐5‐sulfonic acid) aluminum (AlQSA₃), that has three sulfonic acid groups per molecule leading to an excellent solubility in water is reported as a liquid‐free perfect solid‐state electrolyte for flexible film‐type all‐solid‐state energy storage devices. The AlQSA₃ material is synthesized by one‐step reaction of aluminum triisopropoxide and 8‐hydroxyquinoline‐5‐sulfonic acid. The aqueous solutions of AlQSA₃ are applied to fabricate flexible film‐type all‐solid state electric double layer capacitors with indium‐tin oxide thin film electrodes. The ion conductivity of the AlQSA₃ film reaches 0.116 mS cm^?1, while a pronounced hysteresis are obtained in the cyclic voltammetry measurement. The AlQSA₃ film capacitors exhibit an output voltage of 1.5 V at 20 μA cm^?2, which is considerably stable by the repeated operation. In particular, the peak output voltage is well kept even after 180° bending for 500 times in the case of the flexible AlQSA₃ film capacitors.     

Superior Oxygen Reduction Reaction on Phosphorus‐Doped Carbon Dot/Graphene Aerogel for All‐Solid‐State Flexible Al–Air Batteries

Carbon dots have been recognized as one of the most promising candidates for the oxygen reduction reaction (ORR) in alkaline media. However, the desired ORR performance in metal–air batteries is often limited by the moderate electrocatalytic activity and the lack of a method to realize good dispersion. To address these issues, herein a biomass‐deriving method is reported to achieve the in situ phosphorus doping (P‐doping) of carbon dots and their simultaneous decoration onto graphene matrix. The resultant product, namely P‐doped carbon dot/graphene (P‐CD/G) nanocomposites, can reach an ultrahigh P‐doping level for carbon nanomaterials. The P‐CD/G nanocomposites are found to exhibit excellent ORR activity, which is highly comparable to the commercial Pt/C catalysts. When used as the cathode materials for a primary liquid Al–air battery, the device shows an impressive power density of 157.3 mW cm^?2 (comparing to 151.5 mW cm^?2 of a similar Pt/C battery). Finally, an all‐solid‐state flexible Al–air battery is designed and fabricated based on our new nanocomposites. The device exhibits a stable discharge voltage of ≈1.2 V upon different bending states. This study introduces a unique biomass‐derived material system to replace the noble metal catalysts for future portable and wearable electronic devices.     

High‐Performance and Breathable Polypyrrole Coated Air‐Laid Paper for Flexible All‐Solid‐State Supercapacitors

High‐performance, breathable, conductive, and flexible polypyrrole (PPy) coated paper electrodes are prepared by an interfacial polymerization method using air‐laid paper as a substrate. Owing to the synergistic effect of superior electrical conductivity, high wettability, and the porous architecture, the prepared electrode not only shows an outstanding specific capacitance and rate abilities (3100 and 2579 mF cm^?2 at 1 and 20 mA cm^?2 for a PPy coated paper electrode), but also exhibits excellent flexibility, wearability, and breathability. Based on these superior features, an all‐solid‐state supercapacitor assembled with the PPy coated paper electrodes shows an outstanding energy density of 62.4 µW h cm^?2, remarkable air permeability and excellent flexibility to sustain various deformations. Furthermore, large‐scale fabrication of conductive flexible paper electrode can be easily achieved through this method. Therefore, this work offers a new vision for flexible energy storage.     

Solvent‐Free Synthesis of Thin,Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Thin solid‐state electrolytes with nonflammability, high ionic conductivity, low interfacial resistance, and good processability are urgently required for next‐generation safe, high energy density lithium metal batteries. Here, a 3D Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZTO) self‐supporting framework interconnected by polytetrafluoroethylene (PTFE) binder is prepared through a simple grinding method without any solvent. Subsequently, a garnet‐based composite electrolyte is achieved through filling the flexible 3D LLZTO framework with a succinonitrile solid electrolyte. Due to the high content of garnet ceramic (80.4 wt%) and high heat‐resistance of the PTFE binder, such a composite electrolyte film with nonflammability and high processability exhibits a wide electrochemical window of 4.8 V versus Li/Li⁺ and high ionic transference number of 0.53. The continuous Li⁺ transfer channels between interconnected LLZTO particles and succinonitrile, and the soft electrolyte/electrode interface jointly contribute to a high ambient‐temperature ionic conductivity of 1.2 × 10^?4 S cm^?1 and excellent long‐term stability of the Li symmetric battery (stable at a current density of 0.1 mA cm^?2 for over 500 h). Furthermore, as‐prepared LiFePO₄|Li and LiNi_0.5Mn_0.3Co_0.2O₂|Li batteries based on the thin composite electrolyte exhibit high discharge specific capacities of 153 and 158 mAh g^?1 respectively, and desirable cyclic stabilities at room temperature.     

Scalable,Self‐Aligned Printing of Flexible Graphene Micro‐Supercapacitors

Graphene micro‐supercapacitors (MSCs) are an attractive energy storage technology for powering miniaturized portable electronics. Despite considerable advances in recent years, device fabrication typically requires conventional microfabrication techniques, limiting the translation to cost‐effective and high‐throughput production. To address this issue, we report here a self‐aligned printing process utilizing capillary action of liquid inks in microfluidic channels to realize scalable, high‐fidelity manufacturing of graphene MSCs. Microstructured ink receivers and capillary channels are imprinted on plastic substrates and filled by inkjet printing of functional materials into the receivers. The liquid inks move under capillary flow into the adjoining channels, allowing reliable patterning of electronic materials in complex structures with greatly relaxed printing tolerance. Leveraging this process with pristine graphene and ion gel inks, miniaturized all‐solid‐state graphene MSCs are demonstrated to concurrently achieve outstanding resolution (active footprint: <1 mm², minimum feature size: 20 µm) and yield (44/44 devices), while maintaining a high specific capacitance (268 µF cm^–2) and robust stability to extended cycling and bending, establishing an effective route to scale down device size while scaling up production throughput.     

Digital Twin‐Driven All‐Solid‐State Battery: Unraveling the Physical and Electrochemical Behaviors

The digital twin technique has been broadly utilized to efficiently and effectively predict the performance and problems associated with real objects via a virtual replica. However, the digitalization of twin electrochemical systems has not been achieved thus far, owing to the large amount of required calculations of numerous and complex differential equations in multiple dimensions. Nevertheless, with the help of continuous progress in hardware and software technologies, the fabrication of a digital twin‐driven electrochemical system and its effective utilization have become a possibility. Herein, a digital twin‐driven all‐solid‐state battery with a solid sulfide electrolyte is built based on a voxel‐based microstructure. Its validity is verified using experimental data, such as effective electronic/ionic conductivities and electrochemical performance, for LiNi_0.70Co_0.15Mn_0.15O₂ composite electrodes employing Li₆PS₅Cl. The fundamental performance of the all‐solid‐state battery is scrutinized by analyzing simulated physical and electrochemical behaviors in terms of mass transport and interfacial electrochemical reaction kinetics. The digital twin model herein reveals valuable but experimentally inaccessible time‐ and space‐resolved information including dead particles, specific contact area, and charge distribution in the 3D domain. Thus, this new computational model is bound to rapidly improve the all‐solid‐state battery technology by saving the research resources and providing valuable insights.     

Ultrathin,Flexible Polymer Electrolyte for Cost‐Effective Fabrication of All‐Solid‐State Lithium Metal Batteries

All‐solid‐state batteries are promising candidates for the next‐generation safer batteries. However, a number of obstacles have limited the practical application of all‐solid‐state Li batteries (ASSLBs), such as moderate ionic conductivity at room temperature. Here, unlike most of the previous approaches, superior performances of ASSLBs are achieved by greatly reducing the thickness of the solid‐state electrolyte (SSE), where ionic conductivity is no longer a limiting factor. The ultrathin SSE (7.5 µm) is developed by integrating the low‐cost polyethylene separator with polyethylene oxide (PEO)/Li‐salt (PPL). The ultrathin PPL shortens Li⁺ diffusion time and distance within the electrolyte, and provides sufficient Li⁺ conductance for batteries to operate at room temperature. The robust yet flexible polyethylene offers mechanical support for the soft PEO/Li‐salt, effectively preventing short‐circuits even under mechanical deformation. Various ASSLBs with PPL electrolyte show superior electrochemical performance. An initial capacity of 135 mAh g^?1 at room temperature and the high‐rate capacity up to 10 C at 60 °C can be achieved in LiFePO₄/PPL/Li batteries. The high‐energy‐density sulfur cathode and MoS₂ anode employing PPL electrolyte also realize remarkable performance. Moreover, the ASSLB can be assembled by a facile process, which can be easily scaled up to mass production.     

Facile Synthesis of 3D MnO2–Graphene and Carbon Nanotube–Graphene Composite Networks for High‐Performance,Flexible, All‐Solid‐State Asymmetric Supercapacitors

The integration of graphene nanosheets on the macroscopic level using a self‐assembly method has been recognized as one of the most effective strategies to realize the practical applications of graphene materials. Here, a facile and scalable method is developed to synthesis two types of graphene‐based networks, manganese dioxide (MnO₂)–graphene foam and carbon nanotube (CNT)–graphene foam, by solution casting and subsequent electrochemical methods. Their practical applications in flexible all‐solid‐state asymmetric supercapacitors are explored. The proposed method facilitates the structural integration of graphene foam and the electroactive material and offers several advantages including simplicity, efficiency, low‐temperature, and low‐cost. The as‐prepared MnO₂–graphene and CNT–graphene electrodes exhibit high specific capacitances and rate capability. By using polymer gel electrolytes, a flexible all‐solid‐state asymmetric supercapacitor was synthesized with MnO₂–graphene foam as the positive electrode and CNT‐graphene as the negative electrode. The asymmetric supercapacitors can be cycled reversibly in a high‐voltage region of 0 to 1.8 V and exhibit high energy density, remarkable rate capability, reasonable cycling performance, and excellent flexibility.     

Hydrous RuO2‐Decorated MXene Coordinating with Silver Nanowire Inks Enabling Fully Printed Micro‐Supercapacitors with Extraordinary Volumetric Performance

The fabrication of fully printable, flexible micro‐supercapacitors (MSCs) with high energy and power density remains a significant technological hurdle. To overcome this grand challenge, the 2D material MXene has garnered significant attention for its application, among others, as a printable electrode material for high performing electrochemical energy storage devices. Herein, a facile and in situ process is proposed to homogeneously anchor hydrous ruthenium oxide (RuO₂) nanoparticles on Ti₃C₂T_x MXene nanosheets. The resulting RuO₂@MXene nanosheets can associate with silver nanowires (AgNWs) to serve as a printable electrode with micrometer‐scale resolution for high performing, fully printed MSCs. In this printed nanocomposite electrode, the RuO₂ nanoparticles contribute high pseudocapacitance while preventing the MXene nanosheets from restacking, ensuring an effective ion highway for electrolyte ions. The AgNWs coordinate with the RuO₂@MXene to guarantee the rheological property of the electrode ink, and provide a highly conductive network architecture for rapid charge transport. As a result, MSCs printed from the nanocomposite inks demonstrate volumetric capacitances of 864.2 F cm^?3 at 1 mV s^?1, long‐term cycling performance (90% retention after 10 000 cycles), good rate capability (304.0 F cm^?3 at 2000 mV s^?1), outstanding flexibility, remarkable energy (13.5 mWh cm^?3) and power density (48.5 W cm^?3).