Boosting Superior Lithium Storage Performance of Alloy‐Based Anode Materials via Ultraconformal Sb Coating–Derived Favorable Solid‐Electrolyte Interphase

Alloy materials such as Si and Ge are attractive as high‐capacity anodes for rechargeable batteries, but such anodes undergo severe capacity degradation during discharge–charge processes. Compared to the over‐emphasized efforts on the electrode structure design to mitigate the volume changes, understanding and engineering of the solid‐electrolyte interphase (SEI) are significantly lacking. This work demonstrates that modifying the surface of alloy‐based anode materials by building an ultraconformal layer of Sb can significantly enhance their structural and interfacial stability during cycling. Combined experimental and theoretical studies consistently reveal that the ultraconformal Sb layer is dynamically converted to Li₃Sb during cycling, which can selectively adsorb and catalytically decompose electrolyte additives to form a robust, thin, and dense LiF‐dominated SEI, and simultaneously restrain the decomposition of electrolyte solvents. Hence, the Sb‐coated porous Ge electrode delivers much higher initial Coulombic efficiency of 85% and higher reversible capacity of 1046 mAh g^?1 after 200 cycles at 500 mA g^?1, compared to only 72% and 170 mAh g^?1 for bare porous Ge. The present finding has indicated that tailoring surface structures of electrode materials is an appealing approach to construct a robust SEI and achieve long‐term cycling stability for alloy‐based anode materials.     

Lithium‐Pretreated Hard Carbon as High‐Performance Sodium‐Ion Battery Anodes

Hard carbon (HC) is the state‐of‐the‐art anode material for sodium‐ion batteries (SIBs). However, its performance has been plagued by the limited initial Coulombic efficiency (ICE) and mediocre rate performance. Here, experimental and theoretical studies are combined to demonstrate the application of lithium‐pretreated HC (LPHC) as high‐performance anode materials for SIBs by manipulating the solid electrolyte interphase in tetraglyme (TEGDME)‐based electrolyte. The LPHC in TEGDME can 1) deliver > 92% ICE and ≈220 mAh g^?1 specific capacity, twice of the capacity (≈100 mAh g^?1) in carbonate electrolyte; 2) achieve > 85% capacity retention over 1000 cycles at 1000 mA g^?1 current density (4 C rate, 1 C = 250 mA g^?1) with a specific capacity of ≈150 mAh g^?1, ≈15 times of the capacity (10 mAh g^?1) in carbonate. The full cell of Na₃V₂(PO₄)₃‐LPHC in TEGDME demonstrated close to theoretical specific capacity of ≈98 mAh g^?1 based on Na₃V₂(PO₄)₃ cathode, ≈2.5 times of the value (≈40 mAh g^?1) with nontreated HC. This work provides new perception on the anode development for SIBs.     

Li+ Pre‐Insertion Leads to Formation of Solid Electrolyte Interface on TiO2 Nanotubes That Enables High‐Performance Anodes for Sodium Ion Batteries

Recently, sodium ion batteries (SIBs) have been widely investigated as one of the most promising candidates for replacing lithium ion batteries (LIBs). For SIBs or LIBs, designing a stable and uniform solid electrolyte interphase (SEI) at the electrode–electrolyte interface is the key factor to provide high capacity, long‐term cycling, and high‐rate performance. In this paper, it is described how a remarkably enhanced SEI layer can be obtained on TiO₂ nanotube (TiO₂ NTs) arrays that allows for a strongly improved performance of sodium battery systems. Key is that a Li⁺ pre‐insertion in TiO₂ NTs can condition the SEI for Na⁺ replacement. SIBs constructed with Li‐pre‐inserted NTs deliver an exceptional Na⁺ cycling stability (e.g., 99.9 ± 0.1% capacity retention during 250 cycles at a current rate of 50 mA g^?1) and an excellent rate capability (e.g., 132 mA h g^?1 at a current rate of 1 A g^?1). The key factor in this outstanding performance is that Li‐pre‐insertion into TiO₂ NTs leads not only to an enhanced electronic conductivity in the tubes, but also expands the anatase lattice for facilitated subsequent Na⁺ cycling.     

Promoting Highly Reversible Sodium Storage of Iron Sulfide Hollow Polyhedrons via Cobalt Incorporation and Graphene Wrapping

Sodium ion batteries (SIBs) have drawn significant attention owing to their low cost and inherent safety. However, the absence of suitable anode materials with high rate capability and long cycling stability is the major challenge for the practical application of SIBs. Herein, an efficient anode material consisting of uniform hollow iron sulfide polyhedrons with cobalt doping and graphene wrapping (named as CoFeS@rGO) is developed for high‐rate and long‐life SIBs. The graphene‐encapsulated hollow composite assures fast and continuous electron transportation, high Na⁺ ion accessibility, and strong structural integrity, showing an extremely small volume expansion of only 14.9% upon sodiation and negligible volume contraction during the desodiation. The CoFeS@rGO electrode exhibits high specific capacity (661.9 mAh g^?1 at 100 mA g^?1), excellent rate capability (449.4 mAh g^?1 at 5000 mA g^?1), and long cycle life (84.8% capacity retention after 1500 cycles at 1000 mA g^?1). In situ X‐ray diffraction and selected‐area electron diffraction patterns show that this novel CoFeS@rGO electrode is based on a reversible conversion reaction. More importantly, when coupled with a Na₃V₂(PO₄)₃/C cathode, the sodium ion full battery delivers a superexcellent rate capability (496.8 mAh g^?1 at 2000 mA g^?1) and ≈96.5% capacity retention over 200 cycles at 500 mA g^?1 in the 1.0–3.5 V window. This work indicates that the rationally designed anode material is highly applicable for the next generation SIBs with high‐rate capability and long‐term cyclability.     

Tailored Plum Pudding‐Like Co2P/Sn Encapsulated with Carbon Nanobox Shell as Superior Anode Materials for High‐Performance Sodium‐Ion Capacitors

Sodium‐ion capacitors (SICs) are emerging energy storage devices with high energy, high power, and durable life. Sn is a promising anode material for lithium storage, but the poor conductivity of the a‐NaSn phase upon sodaition hinders its implementation in SICs. Herein, a superior Sn‐based anode material consisting of plum pudding‐like Co₂P/Sn yolk encapsulated with nitrogen‐doped carbon nanobox (Co₂P/Sn@NC) for high‐performance SICs is reported. The 8–10 nm metallic nanoparticles produced in situ are uniformly dispersed in the amorphous Sn matrix serving as conductive fillers to facilitate electron transfer in spite of the formation of electrically resistive a‐NaSn phase during cycling. Meanwhile, the carbon shell buffers the large expansion of active Sn and provides a stable electrode–electrolyte interface. Owing to these merits, the yolk–shell Co₂P/Sn@NC demonstrates a large capacity of 394 mA h g^?1 at 100 mA g^?1, high rate capability of 168 mA h g^?1 at 5000 mA g^?1, and excellent cyclability with 87% capacity retention after 10 000 cycles. By integrating the Co₂P/Sn@NC anode with a peanut shell‐derived carbon cathode in the SIC, high energy densities of 112.3 and 43.7 Wh kg^?1 at power densities of 100 and 10 000 W kg^?1 are achieved.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

A Versatile Pyramidal Hauerite Anode in Congeniality Diglyme‐Based Electrolytes for Boosting Performance of Li‐ and Na‐Ion Batteries

For the first time, environmentally friendly sulfur‐rich pyramidal MnS₂ synthesized via a single‐step hydrothermal process is used as a high‐performance anode material in Li‐ion and Na‐ion batteries. The superior electrochemical performance of the MnS₂ electrode along with its high compatibility with ether‐based electrolytes are analyzed in both half‐ and full‐cell configurations. The reversible capacities of ≈84 mAh g^?1 and ≈74 mAh g^?1 at a current density of 50 mA g^?1 are retained in the Li‐ion and Na‐ion full‐cells, respectively, over 200 cycles with excellent capacity retentions. Moreover, important findings regarding activation processes in the presence of a new phase transition and protective electrolyte interphase layer are revealed using ab initio density function theory calculation and in situ potentio‐electrochemical impedance spectroscopy. The detailed complex redox mechanism of MnS₂ in Li/Na half‐cells is also elucidated by ex situ X‐ray photoelectron spectroscopy.     

Fabrication of Hierarchical Potassium Titanium Phosphate Spheroids: A Host Material for Sodium‐Ion and Potassium‐Ion Storage

Identifying suitable electrode materials for sodium‐ion and potassium‐ion storage holds the key to the development of earth‐abundant energy‐storage technologies. This study reports an anode material based on self‐assembled hierarchical spheroid‐like KTi₂(PO₄)₃@C nanocomposites synthesized via an electrospray method. Such an architecture synergistically combines the advantages of the conductive carbon network and allows sufficient space for the infiltration of the electrolyte from the porous structure, leading to an impressive electrochemical performance, as reflected by the high reversible capacity (283.7 mA h g^?1 for Na‐ion batteries; 292.7 mA h g^?1 for K‐ion batteries) and superior rate capability (136.1 mA h g^?1 at 10 A g^?1 for Na‐ion batteries; 133.1 mA h g^?1 at 1 A g^?1 for K‐ion batteries) of the resulting material. Moreover, the different ion diffusion behaviors in the two systems are revealed to account for the difference in rate performance. These findings suggest that KTi₂(PO₄)₃@C is a promising candidate as an anode material for sodium‐ion and potassium‐ion batteries. In particular, the present synthetic approach could be extended to other functional electrode materials for energy‐storage materials.     

Metallic Layered Polyester Fabric Enabled Nickel Selenide Nanostructures as Highly Conductive and Binderless Electrode with Superior Energy Storage Performance

Highly flexible and conductive fabric (CF)‐supported cauliflower‐like nickel selenide nanostructures (Ni₃Se₂ NSs) are facilely synthesized by a single‐step chronoamperometry voltage‐assisted electrochemical deposition (ECD) method and used as a positive electrode in supercapacitors (SCs). The CF substrate composed of multi‐layered metallic films on the surface of polyester fibers enables to provide high electrical conductivity as a working electrode in ECD process. Owing to good electrical conductivity, high porosity and intertwined fibrous framework of CF, cauliflower‐like Ni₃Se₂ NSs are densely integrated onto the entire surface of CF (Ni₃Se₂ NSs@CF) substrate with reliable adhesion by applying a chronoamperometry voltage of ?1.0 V for 240 s. The electrochemical performance of the synthesized cauliflower‐like Ni₃Se₂ NSs@CF electrode exhibits a maximum specific capacity (C _SC) of 119.6 mA h g^?1 at a discharge current density of 2 A g^?1 in aqueous 1 m KOH electrolyte solution. Remarkably, the specific capacity of the same electrode is greatly enhanced by introducing a small quantity of redox‐additive electrolyte into the aqueous KOH solution, indicating the C _SC≈251.82 mA h g^?1 at 2 A g^?1 with good capacity retention. Furthermore, the assembled textile‐based asymmetric SCs achieve remarkable electrochemical performance such as higher energy and power densities, which are able to light up different colored light‐emitting diodes.     

Hydrogenated Core–Shell MAX@K2Ti8O17 Pseudocapacitance with Ultrafast Sodium Storage and Long‐Term Cycling

Sodium‐ion batteries are considered alternatives to lithium‐ion batteries for energy storage devices due to their competitive cost and source abundance. However, the development of electrode materials with long‐term stability and high capacity remains a great challenge. Here, this paper describes for the first time the synthesis of a new class of core–shell MAX@K₂Ti₈O₁₇ by alkaline hydrothermal reaction and hydrogenation of MAX, which grants high sodium ion‐intercalation pseudocapacitance. This composite electrode displays extraordinary reversible capacities of 190 mA h g^?1 at 200 mA g^?1 (0.9 C, theoretical value of ≈219 mA h g^?1) and 150 mA h g^?1 at 1000 mA g^?1 (4.6 C). More importantly, a reversible capacity of 75 mA h g^?1 at 10 000 mA g^?1 (46 C) is retained without any apparent capacity decay even after more than 10 000 cycles. Experimental tests and first‐principle calculations confirm that the increase in Ti³⁺ on the surface layers of MAX@K₂Ti₈O₁₇ by hydrogenation increases its conductivity in addition to enhancing the sodium‐ion intercalation pseudocapacitive process. Furthermore, the distorted dodecahedrons between Ti and O layers not only provide abundant sites for sodium‐ion accommodation but also act as wide tunnels for sodium‐ion transport.     

Si‐Encapsulating Hollow Carbon Electrodes via Electroless Etching for Lithium‐Ion Batteries

Remarkable improvements in the electrochemical performance of Si materials for Li‐ion batteries have been recently achieved, but the inherent volume change of Si still induces electrode expansion and external cell deformation. Here, the void structure in Si‐encapsulating hollow carbons is optimized in order to minimize the volume expansion of Si‐based anodes and improve electrochemical performance. When compared to chemical etching, the hollow structure is achieved via electroless etching is more advanced due to the improved electrical contact between carbon and Si. Despite the very thick electrodes (30 ～ 40 μm), this results in better cycle and rate performances including little capacity fading over 50 cycles and 1100 mA h g^?1 at 2C rate. Also, an in situ dilatometer technique is used to perform a comprehensive study of electrode thickness change, and Si‐encapsulating hollow carbon mitigates the volume change of electrodes by adoption of void space, resulting in a small volume increase of 18% after full lithiation corresponding with a reversible capacity of about 2000 mA h g^?1.     

New Binder‐Free Metal Phosphide–Carbon Felt Composite Anodes for Sodium‐Ion Battery

Metal phosphides are promising anode candidates for sodium‐ion batteries (SIBs) due to their high specific capacity and low operating potential but suffer from poor cycling stability caused by huge volume expansion and poor solid‐state ion transfer rate. Herein, a new strategy to grow a new class of mesoporous metal phosphide nanoarrays on carbon felt (CF) as binder‐free anodes for SIBs is reported. The resultant integrated electrodes demonstrate excellent cycling life up to 1000 times (>90% retention rate) and high rate capability of 535 mAh g^?1 at a current density of 4 A g^?1. Detailed characterization reveals that the synergistic effect of unique mesoporous structure for accommodating huge volume expansion during sodiation/desodiation process, ultrasmall primary particle size (≈10 nm) for providing larger electrode/electrolyte contact area and shorter ion diffusion distance, and 3D conductive networks for facilitating the electrochemical reaction, leads to the extraordinary battery performance. Remarkably, a full SIB using the new CoP₄/CF anode and a Na₃V₂(PO₄)₂F₃ cathode delivers an average operating voltage of ≈3.0 V, a reversible capacity of 553 mAh g^?1, and very high energy density of ≈280 Wh kg^?1 for SIBs. A flexible SIB with outstanding mechanical strength based on this binder‐free new anode is also demonstrated.     

An Improved Li–SeS2 Battery with High Energy Density and Long Cycle Life

Selenium–sulfur solid solutions are a class of potential cathode materials for high energy batteries, since they have higher theoretical capacities than selenium and improved conductivity over sulfur. Here, a high‐performance cathode material by confining 70 wt% of SeS₂ in a highly ordered mesoporous carbon (CMK‐3) framework with a polydopamine (PDA) protection sheath for novel Li–Se/S batteries is reported. With a relatively high SeS₂ mass loading of 2.6–3 mg cm^?2, the CMK‐3/SeS₂@PDA cathode exhibits a high capacity of >1200 mA h g^?1 at 0.2 A g^?1, excellent C‐rate capability of 535 mA h g^?1 at 5 A g^?1, and prolonged life over 500 cycles. Benefitting from the unique advantages of SeS₂ and the rationally designed host framework, this new cathode material demonstrates a feasible strategy to overcome the bottlenecks of current Li–S systems for high energy density rechargeable batteries.     

Development of Safe and Sustainable Dual‐Ion Batteries Through Hybrid Aqueous/Nonaqueous Electrolytes

In this study, a new dual‐ion battery (DIB) concept based on an aqueous/non‐aqueous electrolyte is reported, combining high safety in the form of a nonflammable water‐in‐salt electrolyte, a high cathodic stability by forming a protective interphase on the negative electrode (non‐aqueous solvent), and improved sustainability by using a graphite‐based positive electrode material. Far beyond the anodic stability limit of water, the formation of a stage‐2 acceptor‐type graphite intercalation compound (GIC) of bis(trifluoromethanesulfonyl) imide (TFSI) anions from an aqueous‐based electrolyte is achieved for the first time, as confirmed by ex‐situ X‐ray diffraction. The choice of negative electrode material shows a huge impact on the performance of the DIB cell chemistry, i.e., discharge capacities up to 40 mAh g^?1 are achieved even at a high specific current of 200 mA g^?1. In particular, lithium titanium phosphate (LiTi₂(PO₄)₃; LTP) and lithium titanium oxide (Li₄Ti₅O₁₂; LTO) are evaluated as negative electrodes, exhibiting specific advantages for this DIB setup. In this work, a new DIB storage concept combining an environmentally friendly, transition‐metal‐free, abundant graphite positive electrode material, and a nonflammable water‐based electrolyte is established, thus paving the path toward a sustainable and safe alternative energy storage technology.     

In Situ Revealing the Electroactivity of P?O and P?C Bonds in Hard Carbon for High‐Capacity and Long‐Life Li/K‐Ion Batteries

The low capacity and unsatisfactory rate capability of hard carbon still restricts its practical application for Li/K‐ion batteries. Herein, a low‐cost and large‐scale method is developed to fabricate phosphorus‐doped hard carbon (PHC‐700) by crosslinking phosphoric acid and epoxy resin and followed by annealing at 700 °C. H₃PO₄ acts not only as a crosslinker to solidify epoxy resin for promoting the degree of graphitization and lowering the specific surface area, but also as phosphorus source for forming P? C and P? O bonds, thus providing more active sites for Li/K storage. As a result, the PHC‐700 electrode delivers a highly reversible capacity of 1294.8 mA h g^?1 at 0.1 A g^?1 and a capacity of 214 mA h g^?1 after 10 000 cycles at 10 A g^?1. As for potassium‐ion batteries, PHC‐700 exhibits a reversible capacity of 381.9 mA h g^?1 at 0.1 A g^?1 and a capacity of 260 mA h g^?1 after 1000 cycles at 0.2 A g^?1. In situ Raman and in situ NMR measurements reveal that the P‐containing bonds can enhance the adsorption to alkali metal ions, and the P? C bond can participate in electrochemical redox reaction by forming Li_x PC_y . Additionally, P‐doped hard carbon shows better structural/interfacial stability for improved long‐term cycling stability.     

Ice Templated Free‐Standing Hierarchically WS2/CNT‐rGO Aerogel for High‐Performance Rechargeable Lithium and Sodium Ion Batteries

A hybrid nanoarchitecture aerogel composed of WS₂ nanosheets and carbon nanotube‐reduced graphene oxide (CNT‐rGO) with ordered microchannel three‐dimensional (3D) scaffold structure was synthesized by a simple solvothermal method followed by freeze‐drying and post annealing process. The 3D ordered microchannel structures not only provide good electronic transportation routes, but also provide excellent ionic conductive channels, leading to an enhanced electrochemical performance as anode materials both for lithium‐ion batteries (LIBs) and sodium‐ion batteries (SIBs). Significantly, WS₂/CNT‐rGO aerogel nanostructure can deliver a specific capacity of 749 mA h g^?1 at 100 mA g^?1 and a high first‐cycle coulombic efficiency of 53.4% as the anode material of LIBs. In addition, it also can deliver a capacity of 311.4 mA h g^?1 at 100 mA g^?1, and retain a capacity of 252.9 mA h g^?1 at 200 mA g^?1 after 100 cycles as the anode electrode of SIBs. The excellent electrochemical performance is attributed to the synergistic effect between the WS₂ nanosheets and CNT‐rGO scaffold network and rational design of 3D ordered structure. These results demonstrate the potential applications of ordered CNT‐rGO aerogel platform to support transition‐metal‐dichalcogenides (i.e., WS₂) for energy storage devices and open up a route for material design for future generation energy storage devices.     

Chemical Synthesis of 3D Graphene‐Like Cages for Sodium‐Ion Batteries Applications

Sodium (Na) super ion conductor structured Na₃V₂(PO₄)₃ (NVP) is extensively explored as cathode material for sodium‐ion batteries (SIBs) due to its large interstitial channels for Na⁺ migration. The synthesis of 3D graphene‐like structure coated on NVP nanoflakes arrays via a one‐pot, solid‐state reaction in molten hydrocarbon is reported. The NVP nanoflakes are uniformly coated by the in situ generated 3D graphene‐like layers with the thickness of 3 nm. As a cathode material, graphene covered NVP nanoflakes exhibit excellent electrochemical performances, including close to theoretical reversible capacity (115.2 mA h g^?1 at 1 C), superior rate capability (75.9 mA h g^?1 at 200 C), and excellent cyclic stability (62.5% of capacity retention over 30000 cycles at 50 C). Furthermore, the 3D graphene‐like cages after removing NVP also serve as a good anode material and deliver a specific capacity of 242.5 mA h g^?1 at 0.1 A g^?1. The full SIB using these two cathode and anode materials delivers a high specific capacity (109.2 mA h g^?1 at 0.1 A g^?1) and good cycling stability (77.1% capacity retention over 200 cycles at 0.1 A g^?1).     

Ultrathin Anatase TiO2 Nanosheets Embedded with TiO2‐B Nanodomains for Lithium‐Ion Storage: Capacity Enhancement by Phase Boundaries

A new form of TiO₂ microspheres comprised of anatase/TiO₂‐B ultrathin composite nanosheets has been synthesized successfully and used as Li‐ion storage electrode material. By comparison between samples obtained with different annealing temperatures, it is demonstrated that the anatase/TiO₂‐B coherent interfaces may contribute additional lithium storage venues due to a favorable charge separation at the boundary between the two phases. The as‐prepared hierarchical nanostructures show capacities of 180 and 110 mAh g^?1 after 1000 cycles at current densities of 3400 and 8500 mA g^?1. The ultrathin nanosheet structure which provides short lithium diffusion length and high electrode/electrolyte contact area also accounts for the high capacity and long‐cycle stability.     

Direct Growth of Flower‐Like δ‐MnO2 on Three‐Dimensional Graphene for High‐Performance Rechargeable Li‐O2 Batteries

A challenge still remains to develop high‐performance and cost‐effective air electrode for Li‐O₂ batteries with high capacity, enhanced rate capability and long cycle life (100 times or above) despite recent advances in this field. In this work, a new design of binder‐free air electrode composed of three‐dimensional (3D) graphene (G) and flower‐like δ‐MnO₂ (3D‐G‐MnO₂) has been proposed. In this design, graphene and δ‐MnO₂ grow directly on the skeleton of Ni foam that inherits the interconnected 3D scaffold of Ni foam. Li‐O₂ batteries with 3D‐G‐MnO₂ electrode can yield a high discharge capacity of 3660 mAh g^?1 at 0.083 mA cm^?2. The battery can sustain 132 cycles at a capacity of 492 mAh g^?1 (1000 mAh g_carbon ^?1) with low overpotentials under a high current density of 0.333 mA cm^?2. A high average energy density of 1350 Wh Kg^?1 is maintained over 110 cycles at this high current density. The excellent catalytic activity of 3D‐G‐MnO₂ makes it an attractive air electrode for high‐performance Li‐O₂ batteries.     

A Novel Aluminum‐Ion Battery: Al/AlCl3‐[EMIm]Cl/Ni3S2@Graphene

Due to an ever‐increasing demand for electronic devices, rechargeable batteries are attractive for energy storage systems. A novel rechargeable aluminum‐ion battery based on Al³⁺ intercalation and deintercalation is fabricated with Ni₃S₂/graphene microflakes composite as cathode material and high‐purity Al foil as anode. This kind of aluminum‐ion battery comprises of an electrolyte containing AlCl₃ in an ionic liquid of 1‐ethyl‐3‐methylimidazolium chloride ([EMIm]Cl). Galvanostatic charge/discharge measurements have been performed in a voltage range of 0.1–2.0 V versus Al/AlCl₄ ^?. An initial discharge specific capacity of 350 mA h g^?1 at a current density of 100 mA g^?1 is achieved, and the discharge capacity remains over 60 mA h g^?1 and coulombic efficiency of 99% after 100 cycles. Typically, for the current density at 200 mA g^?1, the initial charge and discharge capacities are 300 and 235 mA h g^?1, respectively. More importantly, it should be emphasized that the battery has a high discharge voltage plateau (≈1.0 V vs Al/AlCl₄ ^?). These meaningful results represent a significant step forward in the development of aluminum‐ion batteries.