A High‐Crystalline NaV1.25Ti0.75O4 Anode for Wide‐Temperature Sodium‐Ion Battery

Sodium‐ion batteries with abundant and low‐cost sodium resources is a promising alternative to Li‐ion batteries in large‐scale energy applications. While the anode materials, due to their insufficient cycling life and insecure voltage, could not still satisfy the market demands, especially in the wide‐temperature fields, here, a high‐crystallinity anode material with post‐spinel structure, namely NaV_1.25Ti_0.75O₄, which always maintains excellent electrochemical performance at the widely variable temperatures, is reported. The results indicate that this anode delivers a high‐safety and ultrastable room‐temperature performance (i.e., an average output voltage of 0.7 V vs Na⁺/Na and the ultralong cycling life over 10 000 cycles) and good wide‐temperature performance (below 9% capacity variation at 60 and ?20 °C compared to that at 25 °C). These excellent achievements could benefit from the long durability and stability of 1D channels and superfast ion diffusion in a temperature‐dependent range. This finding provides a promising strategy to construct the safe and stable full‐cell prototypes and promotes the wide‐temperature application of sodium‐ion batteries.     

3D Amorphous Carbon with Controlled Porous and Disordered Structures as a High‐Rate Anode Material for Sodium‐Ion Batteries

Sodium‐ion batteries (SIBs) have a promising application prospect for energy storage systems due to the abundant resource. Amorphous carbon with high electronic conductivity and high surface area is likely to be the most promising anode material for SIBs. However, the rate capability of amorphous carbon in SIBs is still a big challenge because of the sluggish kinetics of Na⁺ ions. Herein, a three‐dimensional amorphous carbon (3DAC) with controlled porous and disordered structures is synthesized via a facile NaCl template‐assisted method. Combination of open porous structures of 3DAC, the increased disordered structures can not only facilitate the diffusion of Na⁺ ions but also enhance the reversible capacity of Na storage. When applied as anode materials for SIBs, 3DAC exhibits excellent rate capability (66 mA h g^?1 at 9.6 A g^?1) and high reversible capacity (280 mA h g^?1 at a low current density of 0.03 A g^?1). Moreover, the controlled porous structures by the NaCl template method provide an appropriate specific surface area, which contributes to a relatively high initial Coulombic efficiency of 75%. Additionally, the high‐rate 3DAC material is prepared via a green approach originating from low‐cost pitch and NaCl template, demonstrating an appealing development of carbon anode materials for SIBs.     

Nanosheets‐Assembled CuSe Crystal Pillar as a Stable and High‐Power Anode for Sodium‐Ion and Potassium‐Ion Batteries

Thanks to low costs and the abundance of the resources, sodium‐ion (SIBs) and potassium‐ion batteries (PIBs) have emerged as leading candidates for next‐generation energy storage devices. So far, only few materials can serve as the host for both Na⁺ and K⁺ ions. Herein, a cubic phase CuSe with crystal‐pillar‐like morphology (CPL‐CuSe) assembled by the nanosheets are synthesized and its dual functionality in SIBs and PIBs is comprehensively studied. The electrochemical measurements demonstrate that CPL‐CuSe enables fast Na⁺ and K⁺ storage as well as the sufficiently long duration. Specifically, the anode delivers a specific capacity of 295 mA h g^?1 at current density of 10 A g^?1 in SIBs, while 280 mA h g^?1 at 5 A g^?1 in PIBs, as well as the high capacity retention of nearly 100% over 1200 cycles and 340 cycles, respectively. Remarkably, CPL‐CuSe exhibits a high initial coulombic efficiency of 91.0% (SIBs) and 92.4% (PIBs), superior to most existing selenide anodes. A combination of in situ X‐ray diffraction and ex situ transmission electron microscopy tests fundamentally reveal the structural transition and phase evolution of CuSe, which shows a reversible conversion reaction for both cells, while the intermediate products are different due to the sluggish K⁺ insertion reaction.     

Anodes and Sodium‐Free Cathodes in Sodium Ion Batteries

The increase in electricity generation poses growing demands on energy storage systems, thus offering a chance for the success of the reliable and cost‐effective energy storage technologies. Sodium ion batteries are emerging as such a technology, which is however not yet mature enough to enter the market. At the crux of building practical sodium ion batteries is the development of electrode materials that promise sufficient cost‐ and performance‐competitiveness. As such, herein, all typical sodium storage materials are discussed, considering their fabrication methods and sodiation mechanisms in detail. A comprehensive cross‐literature and cross‐material comparison, which also includes the related thermodynamic analysis of their sodiation products, is also provided. The review focusses particularly on anodes and sodium‐free cathodes, as they both play the role of the acceptor rather than the donor of sodium ions in their operation in batteries; their difference lies in the (de‐)sodiation voltage. In the discussion, special attention is paid to contradictory observations and interpretations in contemporary sodium ion battery research, since debates on these controversies are likely to fuel future sodium battery research.     

Nanoconfined Carbon‐Coated Na3V2(PO4)3 Particles in Mesoporous Carbon Enabling Ultralong Cycle Life for Sodium‐Ion Batteries

Na₃V₂(PO₄)₃ (denoted as NVP) has been considered as a promising cathode material for room temperature sodium ion batteries. Nevertheless, NVP suffers from poor rate capability resulting from the low electronic conductivity. Here, the feasibility to approach high rate capability by designing carbon‐coated NVP nanoparticles confined into highly ordered mesoporous carbon CMK‐3 matrix (NVP@C@CMK‐3) is reported. The NVP@C@CMK‐3 is prepared by a simple nanocasting technique. The electrode exhibits superior rate capability and ultralong cyclability (78 mA h g^?1 at 5 C after 2000 cycles) compared to carbon‐coated NVP and pure NVP cathode. The improved electrochemical performance is attributed to double carbon coating design that combines a variety of advantages: very short diffusion length of Na⁺/e^? in NVP, easy access of electrolyte, and short transport path of Na⁺ through carbon toward the NVP nanoparticle, high conductivity transport of electrons through the 3D interconnected channels of carbon host. The optimum design of the core–shell nanostructures with double carbon coating permits fast kinetics for both transported Na⁺ ions and electrons, enabling high‐power performance.     

Partially Reduced Holey Graphene Oxide as High Performance Anode for Sodium‐Ion Batteries

The current Na⁺ storage performance of carbon‐based materials is still hindered by the sluggish Na⁺ ion transfer kinetics and low capacity. Graphene and its derivatives have been widely investigated as electrode materials in energy storage and conversion systems. However, as anode materials for sodium‐ion batteries (SIBs), the severe π–π restacking of graphene sheets usually results in compact structure with a small interlayer distance and a long ion transfer distance, thus leading to low capacity and poor rate capability. Herein, partially reduced holey graphene oxide is prepared by simple H₂O₂ treatment and subsequent low temperature reduction of graphene oxide, leading to large interlayer distance (0.434 nm), fast ion transport, and larger Na⁺ storage space. The partially remaining oxygenous groups can also contribute to the capacity by redox reaction. As anode material for SIBs, the optimized electrode delivers high reversible capacity, high rate capability (365 and 131 mAh g^?1 at 0.1 and 10 A g^?1, respectively), and good cycling performance (163 mAh g^?1 after 3000 cycles at a current density of 2 A g^?1), which is among the best reported performances for carbon‐based SIB anodes.     

Hard Carbon Microtubes Made from Renewable Cotton as High‐Performance Anode Material for Sodium‐Ion Batteries

Sodium‐ion batteries (SIBs) have attracted more and more attention for scalable electrical energy storage due to the abundance and wide distribution of Na resources. However, the anode still remains a great challenge for the application of SIBs. Here the production of uniform hard carbon microtubes (HCTs) made from natural cotton through one simple carbonization process and their application as an anode are reported. The study shows that the electrochemical performance of the HCTs is seriously affected by the carbonization temperature due to the difference in their microstructure and heteroatomic content. The HCTs carbonized at 1300 °C deliver the highest reversible capacity of 315 mAh g^?1 and good rate capability due to their unique tubular structure. This contribution not only provides a new approach for the preparation of hard carbon materials with unique tubular microstructure using natural inspiration, but it also deepens the fundamental understanding of the sodium storage mechanism.     

CuS Microspheres with Tunable Interlayer Space and Micropore as a High‐Rate and Long‐Life Anode for Sodium‐Ion Batteries

Layered transition metal sulfides (LTMSs) have tremendous commercial potential in anode materials for sodium‐ion batteries (SIBs) in large‐scale energy storage application. However, it is a great challenge for most LTMS electrodes to have long cycling life and high‐rate capability due to their larger volume expansion and the formation of soluble polysulfide intermediates caused by the conversion reaction. Herein, layered CuS microspheres with tunable interlayer space and pore volumes are reported through a cost‐effective interaction method using a cationic surfactant of cetyltrimethyl ammonium bromide (CTAB). The CuS–CTAB microsphere as an anode for SIBs reveals a high reversible capacity of 684.6 mAh g^?1 at 0.1 A g^?1, and 312.5 mAh g^?1 at 10 A g^?1 after 1000 cycles with high capacity retention of 90.6%. The excellent electrochemical performance is attributed to the unique structure of this material, and a high pseudocapacitive contribution ensures its high‐rate performance. Moreover, in situ X‐ray diffraction is applied to investigate their sodium storage mechanism. It is found that the long chain CTAB in the CuS provides buffer space, traps polysulfides, and restrains the further growth of Cu particles during the conversion reaction process that ensure the long cycling stability and high reversibility of the electrode material.     

Highly Doped 3D Graphene Na‐Ion Battery Anode by Laser Scribing Polyimide Films in Nitrogen Ambient

Conventional graphite anodes can hardly intercalate sodium (Na) ions, which poses a serious challenge for developing Na‐ion batteries. This study details a novel method that involves single‐step laser‐based transformation of urea‐containing polyimide into an expanded 3D graphene anode, with simultaneous doping of high concentrations of nitrogen (≈13 at%). The versatile nature of this laser‐scribing approach enables direct bonding of the 3D graphene anode to the current collectors without the need for binders or conductive additives, which presents a clear advantage over chemical or hydrothermal methods. It is shown that these conductive and expanded 3D graphene structures perform exceptionally well as anodes for Na‐ion batteries. Specifically, an initial coulombic efficiency (CE) up to 74% is achieved, which exceeds that of most reported carbonaceous anodes, such as hard carbon and soft carbon. In addition, Na‐ion capacity up to 425 mAh g^?1 at 0.1 A g^?1 has been achieved with excellent rate capabilities. Further, a capacity of 148 mAh g^?1 at a current density of 10 A g^?1 is obtained with excellent cycling stability, opening a new direction for the fabrication of 3D graphene anodes directly on current collectors for metal ion battery anodes as well as other potential applications.     

Soft Carbon as Anode for High‐Performance Sodium‐Based Dual Ion Full Battery

Sodium‐based dual ion full batteries (NDIBs) are reported with soft carbon as anode and graphite as cathode for the first time. The NDIBs operate at high discharge voltage plateau of 3.58 V, with superior discharge capacity of 103 mA h g^?1, excellent rate performance, and long‐term cycling stability over 800 cycles with capacity retention of 81.8%. The mechanism of Na⁺ and PF₆^? insertion/desertion during the charging/discharging processes is proposed and discussed in detail, with the support of various spectroscopies.     

Fabrication of Hierarchical Potassium Titanium Phosphate Spheroids: A Host Material for Sodium‐Ion and Potassium‐Ion Storage

Identifying suitable electrode materials for sodium‐ion and potassium‐ion storage holds the key to the development of earth‐abundant energy‐storage technologies. This study reports an anode material based on self‐assembled hierarchical spheroid‐like KTi₂(PO₄)₃@C nanocomposites synthesized via an electrospray method. Such an architecture synergistically combines the advantages of the conductive carbon network and allows sufficient space for the infiltration of the electrolyte from the porous structure, leading to an impressive electrochemical performance, as reflected by the high reversible capacity (283.7 mA h g^?1 for Na‐ion batteries; 292.7 mA h g^?1 for K‐ion batteries) and superior rate capability (136.1 mA h g^?1 at 10 A g^?1 for Na‐ion batteries; 133.1 mA h g^?1 at 1 A g^?1 for K‐ion batteries) of the resulting material. Moreover, the different ion diffusion behaviors in the two systems are revealed to account for the difference in rate performance. These findings suggest that KTi₂(PO₄)₃@C is a promising candidate as an anode material for sodium‐ion and potassium‐ion batteries. In particular, the present synthetic approach could be extended to other functional electrode materials for energy‐storage materials.