Enhanced Cathodic Oxygen Reduction and Power Production of Microbial Fuel Cell Based on Noble‐Metal‐Free Electrocatalyst Derived from Metal‐Organic Frameworks

Microbial fuel cell (MFC) can generate electricity from organic substances based on anodic electrochemically active microorganisms and cathodic oxygen reduction reaction (ORR), thus exhibiting promising potential for harvesting electric energy from organic wastewater. The ORR performance is crucial to both power production efficiency and overall cost of MFC. A new type of metal‐organic‐framework‐derived electrocatalysts containing cobalt and nitrogen‐doped carbon (CoNC) is developed, which is effective to enhance activity, selectivity, and stability toward four‐electron ORR in pH‐neutral electrolyte. When glucose is used as the substrate, the maximum power density of 1665 mW m^?2 is achieved for the optimized CoNC pyrolyzed at 900 °C, which is 39.8% higher than that of 1191 mW m^?2 for commercial Pt/C catalyst in the single‐chamber MFC. The improved performance of CoNC catalyst can be attributed to large surface area, microporous nature, and the involvement of nitrogen‐coordinated cobalt species. These properties enable the efficient ORR by increasing the active sites and enhancing mass transfer of oxygen and protons at “water‐flooding” three‐phase boundary where ORR occurs. This work provides a proof‐of‐concept demonstration of a noble‐metal‐free high‐efficiency and cost‐effective ORR electrocatalyst for effective recovery of electricity from biomass materials and organic wastewater in MFC.     

Development of a solar-powered microbial fuel cell

Aims: To understand factors that impact solar‐powered electricity generation by Rhodobacter sphaeroides in a single‐chamber microbial fuel cell (MFC). Methods and Results: The MFC used submerged platinum‐coated carbon paper anodes and cathodes of the same material, in contact with atmospheric oxygen. Power was measured by monitoring voltage drop across an external resistance. Biohydrogen production and in situ hydrogen oxidation were identified as the main mechanisms for electron transfer to the MFC circuit. The nitrogen source affected MFC performance, with glutamate and nitrate‐enhancing power production over ammonium. Conclusions: Power generation depended on the nature of the nitrogen source and on the availability of light. With light, the maximum point power density was 790 mW m^?2 (2·9 W m^?3). In the dark, power output was less than 0·5 mW m^?2 (0·008 W m^?3). Also, sustainable electrochemical activity was possible in cultures that did not receive a nitrogen source. Significance and Impact of the Study: We show conditions at which solar energy can serve as an alternative energy source for MFC operation. Power densities obtained with these one‐chamber solar‐driven MFC were comparable with densities reported in nonphotosynthetic MFC and sustainable for longer times than with previous work on two‐chamber systems using photosynthetic bacteria.     

Enhancement of extracellular electron transfer and bioelectricity output by synthetic porin

The microbial fuel cell (MFC), is a promising environmental biotechnology for harvesting electricity energy from organic wastes. However, low bacterial membrane permeability of electron shuttles is a limiting factor that restricts the electron shuttle‐mediated extracellular electron transfer (EET) from bacteria to electrodes, thus the electricity power output of MFCs. To this end, we heterologously expressed a porin protein OprF from Pseudomonas aeruginosa PAO1 into Escherichia coli, which dramatically increased its membrane permeability, delivering a much higher current output in MFCs than its parental strain (BL21). We found that the oprF‐expression strain showed more efficient EET than its parental strain. More strikingly, the enhanced membrane permeability also rendered the oprF‐expression strain an efficient usage of riboflavin as the electron shuttle, whereas its parental strain was incapable of. Our results substantiated that membrane permeability is crucial for the efficient EET, and indicated that the expression of synthetic porins could be an efficient strategy to enhance bioelectricity generation by microorganisms (including electrogenic bacteria) in MFCs. Biotechnol. Bioeng. 2013; 110: 408–416. © 2012 Wiley Periodicals, Inc.     

Flexible and Stretchable Biobatteries: Monolithic Integration of Membrane‐Free Microbial Fuel Cells in a Single Textile Layer

The fabrication and performance of a flexible and stretchable microbial fuel cell (MFC) monolithically integrated into a single sheet of textile substrate are reported. The single‐layer textile MFC uses Pseudomonas aeruginosa (PAO1) as a biocatalyst to produce a maximum power of 6.4 µW cm^?2 and current density of 52 µA cm^?2, which are substantially higher than previous textile‐MFCs and are similar to other flexible paper‐based MFCs. The textile MFC demonstrates a stable performance with repeated stretching and twisting cycles. The membrane‐less single‐chamber configuration drastically simplifies the fabrication and improves the performance of the MFC. A conductive and hydrophilic anode in a 3D fabric microchamber maximizes bacterial electricity generation from a liquid environment and a silver oxide/silver solid‐state cathode reduces cathodic overpotential for fast catalytic reaction. A simple batch fabrication approach simultaneously constructs 35 individual devices, which will revolutionize the mass production of textile MFCs. This stretchable and twistable power device printed directly onto a single textile substrate can establish a standardized platform for textile‐based biobatteries and will be potentially integrated into wearable electronics in the future.     

Effects of inoculation strategy and cultivation approach on the performance of microbial fuel cell using marine sediment as bio-matrix

Aims: To investigate the effects of inoculation strategy and cultivation approach on the performance of microbial fuel cell (MFC). Methods and Results: A dual‐chamber sediment fuel cell was set up fed with glucose under batch condition. At day 30, the supernatant consortium was partly transferred and used as inoculum for the evaluation of cultivation approach. Power output gradually increased to 9·9 mW m^?2 over 180 days, corresponding to coulombic efficiency (CE) of 29·6%. Separated biofilms attached anode enabled power output and CE dramatically up to 100·9 mW m^?2 and over 50%, respectively, whereas the residual sediment catalysed MFC gave a poor performance. MFC catalysed by in situ supernatant consortium demonstrated more than twice higher power than MFC catalysed by the supernatant consortium after Fe(OH)₃ cultivation. However, the re‐generation of biofilms from the latter largely enhanced the cell performance. Conclusions: MFC exhibited a more efficient inducement of electroactive consortium than Fe(OH)₃ cultivation. MFC performance varied depending on different inoculation strategies. Significance and Impact of the Study: This is the first time to study cultivation approach affecting electricity generation. In addition, anodic limitations of mass and electron transfer were discussed through MFC catalysed by sediment‐based bio‐matrix.     

Metabolic modeling of spatial heterogeneity of biofilms in microbial fuel cells reveals substrate limitations in electrical current generation

Microbial fuel cells (MFCs) have been proposed as an alternative energy resource for the conversion of organic compounds to electricity. In an MFC, microorganisms such as Geobacter sulfurreducens form an anode‐associated biofilm that can completely oxidize organic matter (electron donor) to carbon dioxide with direct electron transfer to the anode (electron acceptor). Mathematical models are useful in analyzing biofilm processes; however, existing models rely on Nernst–Monod type expressions, and evaluate extracellular processes separated from the intracellular metabolism of the microorganism. Thus, models that combine both extracellular and intracellular components, while addressing spatial heterogeneity, are essential for improved representation of biofilm processes. The goal of this work is to develop a model that integrates genome‐scale metabolic models with the model of biofilm environment. This integrated model shows the variations of electrical current production and biofilm thickness under the presence/absence of NH₄ in the bulk solution, and under varying maintenance energy demands. Further, sensitivity analysis suggested that conductivity is not limiting electrical current generation and that increasing cell density can lead to enhanced current generation. In addition, the modeling results also highlight instances such as the transformation into respiring cells, where the mechanism of electrical current generation during biofilm development is not yet clearly understood.     

Electrochemical analysis of Clostridium propionicum and its acrylic acid production in microbial fuel cells

Currently, acrylic acid is produced at a low yield by the resting cells of Clostridium propionicum with the supplement of extra electron acceptors. As an alternative way, acrylic acid production coupled with electricity generation was achieved by C. propionicum‐based microbial fuel cells (MFCs). Electricity was generated in the salt‐bridge MFCs with cysteine and resazurin in the anode chamber as mediators, and K₃Fe(CN)₆ as the cathode electron acceptor. Power generation was 21.78 mW/m² with an internal resistance of 9809 Ω. Cyclic voltammograms indicated the main mechanism of power production was the electron transfer facilitated by mediators in the system. In the salt‐bridge MFC system, 0.694 mM acrylic acid was produced together with electricity generation.     

Impedance spectroscopy as a tool for non‐intrusive detection of extracellular mediators in microbial fuel cells

Endogenously produced, diffusible redox mediators can act as electron shuttles for bacterial respiration. Accordingly, the mediators also serve a critical role in microbial fuel cells (MFCs), as they assist extracellular electron transfer from the bacteria to the anode serving as the intermediate electron sink. Electrochemical impedance spectroscopy (EIS) may be a valuable tool for evaluating the role of mediators in an operating MFC. EIS offers distinct advantages over some conventional analytical methods for the investigation of MFC systems because EIS can elucidate the electrochemical properties of various charge transfer processes in the bio‐energetic pathway. Preliminary investigations of Shewanella oneidensis DSP10‐based MFCs revealved that even low quantities of extracellular mediators significantly influence the impedance behavior of MFCs. EIS results also suggested that for the model MFC studied, electron transfer from the mediator to the anode may be up to 15 times faster than the electron transfer from bacteria to the mediator. When a simple carbonate membrane separated the anode and cathode chambers, the extracellular mediators were also detected at the cathode, indicating diffusion from the anode under open circuit conditions. The findings demonstrated that EIS can be used as a tool to indicate presence of extracellular redox mediators produced by microorganisms and their participation in extracellular electron shuttling. Biotechnol. Bioeng. 2009; 104: 882–891. © 2009 Wiley Periodicals, Inc.     

Electricity generation and microbial community analysis of alcohol powered microbial fuel cells

Two different microbial fuel cell (MFC) configurations were investigated for electricity production from ethanol and methanol: a two-chambered, aqueous-cathode MFC; and a single-chamber direct-air cathode MFC. Electricity was generated in the two-chamber system at a maximum power density typical of this system (40+/-2 mW/m2) and a Coulombic efficiency (CE) ranging from 42% to 61% using ethanol. When bacteria were transferred into a single-chamber MFC known to produce higher power densities with different substrates, the maximum power density increased to 488+/-12 mW/m2 (CE = 10%) with ethanol. The voltage generated exhibited saturation kinetics as a function of ethanol concentration in the two-chambered MFC, with a half-saturation constant (Ks) of 4.86 mM. Methanol was also examined as a possible substrate, but it did not result in appreciable electricity generation. Analysis of the anode biofilm and suspension from a two-chamber MFC with ethanol using 16S rDNA-based techniques indicated that bacteria with sequences similar to Proteobacterium Core-1 (33.3% of clone library sequences), Azoarcus sp. (17.4%), and Desulfuromonas sp. M76 (15.9%) were significant members of the anode chamber community. These results indicate that ethanol can be used for sustained electricity generation at room temperature using bacteria on the anode in a MFC.     

Simultaneous carbon and nitrogen removal from piggery wastewater using loop configuration microbial fuel cell

Simultaneous carbon and nitrogen removal using loop configuration microbial fuel cell (MFC) with relatively large size of 5 L was investigated in this study. Four MFC reactors were constructed with a loop configuration to eliminate the pH gradient, and the reactor performance was examined with different separators and cathode materials. The performance of the reactors in terms of electricity generation and contaminant removal rate was examined. Results showed that a maximum power density of 1415.6 mW/m³ (The empty bed volume of anode chamber) was obtained at a current density of 3258.5 mA/m³ with cation exchange membrane as separator and graphite felt (Pt coated) as cathode using the piggery wastewater as feed, and the organic removal rate obtained was approximately 0.523 kg COD/m³/d (total anode chamber) with nitrogen removal rate of 0.194 kg N/m³/d (total cathode chamber).     

A kinetic perspective on extracellular electron transfer by anode-respiring bacteria

In microbial fuel cells and electrolysis cells (MXCs), anode-respiring bacteria (ARB) oxidize organic substrates to produce electrical current. In order to develop an electrical current, ARB must transfer electrons to a solid anode through extracellular electron transfer (EET). ARB use various EET mechanisms to transfer electrons to the anode, including direct contact through outer-membrane proteins, diffusion of soluble electron shuttles, and electron transport through solid components of the extracellular biofilm matrix. In this review, we perform a novel kinetic analysis of each EET mechanism by analyzing the results available in the literature. Our goal is to evaluate how well each EET mechanism can produce a high current density (>10 A m⁻²) without a large anode potential loss (less than a few hundred millivolts), which are feasibility goals of MXCs. Direct contact of ARB to the anode cannot achieve high current densities due to the limited number of cells that can come in direct contact with the anode. Slow diffusive flux of electron shuttles at commonly observed concentrations limits current generation and results in high potential losses, as has been observed experimentally. Only electron transport through a solid conductive matrix can explain observations of high current densities and low anode potential losses. Thus, a study of the biological components that create a solid conductive matrix is of critical importance for understanding the function of ARB.     

产电微生物及微生物燃料电池最新研究进展

新型产电微生物(Electricigens)的发现,使得微生物燃料电池概念的内涵发生了根本性的变化,展现了广阔的应用前景。这种微生物能够以电极作为唯一电子受体,把氧化有机物获得的电子通过电子传递链传递到电极产生电流,同时微生物从中获得能量而生长。这种代谢被认为是一种新型微生物呼吸方式。以这种新型微生物呼吸方式为基础的微生物燃料电池可以同时进行废水处理和生物发电,有望可以把废水处理发展成一个有利可图的产业,是MFC最有发展前景的方向。     

Integrated organic and nitrogen removal with electricity generation in a tubular dual-cathode microbial fuel cell

This study presented a dual-cathode microbial fuel cell (MFC) that was designed to accomplish nitrification in its outer cathode and denitrification in the inner cathode. The MFC was continuously operated for more than 150 days and achieved organic removal of 85–99% in the anode, depending on the initial organic loading rates. More than 96% of the ammonium was removed, while the total nitrogen removal was between 66.7 and 89.6%, largely affected by the remaining nitrate in the effluent of the inner cathode. The coulombic efficiency suggested that the nitrate was primarily removed by bioelectrochemcial denitrification in the inner cathode, especially at the low nitrogen loading rates. However, a higher nitrogen loading rate encouraged nitrate migration through the anion exchange membrane, thereby being removed by conventional denitrification. The preliminary energy analysis suggested that the energy production in the dual-cathode MFC could potentially support its pumping system. To achieve an energy-neutral system, aeration must be omitted in the future design and passive oxygen supply should be considered with a proper design of the outer cathode. Those results demonstrated the feasibility of using a tubular dual-cathode MFC to remove both organics and nitrogen while producing electricity.     

Analysis of ammonia loss mechanisms in microbial fuel cells treating animal wastewater

Ammonia losses during swine wastewater treatment were examined using single- and two-chambered microbial fuel cells (MFCs). Ammonia removal was 60% over 5 days for a single-chamber MFC with the cathode exposed to air (air-cathode), versus 69% over 13 days from the anode chamber in a two-chamber MFC with a ferricyanide catholyte. In both types of systems, ammonia losses were accelerated with electricity generation. For the air-cathode system, our results suggest that nitrogen losses during electricity generation were increased due to ammonia volatilization with conversion of ammonium ion to the more volatile ammonia species as a result of an elevated pH near the cathode (where protons are consumed). This loss mechanism was supported by abiotic tests (applied voltage of 1.1 V). In a two-chamber MFC, nitrogen losses were primarily due to ammonium ion diffusion through the membrane connecting the anode and cathode chambers. This loss was higher with electricity generation as the rate of ammonium transport was increased by charge transfer across the membrane. Ammonia was not found to be used as a substrate for electricity generation, as intermittent ammonia injections did not produce power. The ammonia-oxidizing bacterium Nitrosomonas europaea was found on the cathode electrode of the single-chamber system, supporting evidence of biological nitrification, but anaerobic ammonia-oxidizing bacteria were not detected by molecular analyses. It is concluded that ammonia losses from the anode chamber were driven primarily by physical-chemical factors that are increased with electricity generation, although some losses may occur through biological nitrification and denitrification.     

Control of malodorous hydrogen sulfide compounds using microbial fuel cell

In this study, a microbial fuel cell (MFC) was used to control malodorous hydrogen sulfide compounds generated from domestic wastewaters. The electricity production demonstrated a distinct pattern of a two-step increase during 170 h of system run: the first maximum current density was 118.6 ± 7.2 mA m^?2 followed by a rebound of current density increase, reaching the second maximum of 176.8 ± 9.4 mA m^?2. The behaviors of the redox potential and the sulfate level in the anode compartment indicated that the microbial production of hydrogen sulfide compounds was suppressed in the first stage, and the hydrogen sulfide compounds generated from the system were removed effectively as a result of their electrochemical oxidation, which contributed to the additional electricity production in the second stage. This was also directly supported by sulfur deposits formed on the anode surface, which was confirmed by analyses on those solids using a scanning electron microscope equipped with energy dispersive X-ray spectroscopy as well as an elemental analyzer. To this end, the overall reduction efficiencies for HS^? and H₂S_(g) were as high as 67.5 and 96.4 %, respectively. The correlations among current density, redox potential, and sulfate level supported the idea that the electricity signal generated in the MFC can be utilized as a potential indicator of malodor control for the domestic wastewater system.     

Expression of serotonin derivative synthetic genes on a single self-processing polypeptide and the production of serotonin derivatives in microbes

Soils are rich in organics, particularly those that support growth of plants. These organics are possible sources of sustainable energy, and a microbial fuel cell (MFC) system can potentially be used for this purpose. Here, we report the application of an MFC system to electricity generation in a rice paddy field. In our system, graphite felt electrodes were used; an anode was set in the rice rhizosphere, and a cathode was in the flooded water above the rhizosphere. It was observed that electricity generation (as high as 6 mW/m², normalized to the anode projection area) was sunlight dependent and exhibited circadian oscillation. Artificial shading of rice plants in the daytime inhibited the electricity generation. In the rhizosphere, rice roots penetrated the anode graphite felt where specific bacterial populations occurred. Supplementation to the anode region with acetate (one of the major root-exhausted organic compounds) enhanced the electricity generation in the dark. These results suggest that the paddy-field electricity-generation system was an ecological solar cell in which the plant photosynthesis was coupled to the microbial conversion of organics to electricity.     

Investigating microbial fuel cell bioanode performance under different cathode conditions

A compact, three‐in‐one, flow‐through, porous, electrode design with minimal electrode spacing and minimal dead volume was implemented to develop a microbial fuel cell (MFC) with improved anode performance. A biofilm‐dominated anode consortium enriched under a multimode, continuous‐flow regime was used. The increase in the power density of the MFC was investigated by changing the cathode (type, as well as catholyte strength) to determine whether anode was limiting. The power density obtained with an air‐breathing cathode was 56 W/m³ of net anode volume (590 mW/m²) and 203 W/m³ (2160 mW/m²) with a 50‐mM ferricyanide‐based cathode. Increasing the ferricyanide concentration and ionic strength further increased the power density, reaching 304 W/m³ (3220 mW/m², with 200 mM ferricyanide and 200 mM buffer concentration). The increasing trend in the power density indicated that the anode was not limiting and that higher power densities could be obtained using cathodes capable of higher rates of oxidation. The internal solution resistance for the MFC was 5–6 Ω, which supported the improved performance of the anode design. A new parameter defined as the ratio of projected surface area to total anode volume is suggested as a design parameter to relate volumetric and area‐based power densities and to enable comparison of various MFC configurations. Published 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

产电微生物基因调控网络的构建和特异性通路分析

研究产电微生物胞外电子传递过程和机制,发现与产电效率相关的关键基因、通路和代谢物,是微生物燃料电池研究中的关键技术。为了发现在胞外电子传递过程中起到关键作用的基因以及通路,首先利用比较基因组学的方法,以模式微生物大肠杆菌和同属希瓦氏菌的其他菌株为参考,构建了Shewanella.onedensis MR-1的全基因组基因转录调控网络,大大扩展了目前已知的基因调控关系。然后以此网络为基础,结合基于蛋白质相互作用分析得到的胞外电子传递通路,构建了与胞外电子传递直接传递密切相关的细胞色素C编码基因及其相关调控基因构成的子网络,结合全基因组基因表达数据,研究了特异性条件下胞外电子传递的可能通路和基因调控过程。     

Effect of nitrogen addition on the performance of microbial fuel cell anodes

Carbon cloth anodes were modified with 4(N,N-dimethylamino)benzene diazonium tetrafluoroborate to increase nitrogen-containing functional groups at the anode surface in order to test whether the performance of microbial fuel cells (MFCs) could be improved by controllably modifying the anode surface chemistry. Anodes with the lowest extent of functionalization, based on a nitrogen/carbon ratio of 0.7 as measured by XPS, achieved the highest power density of 938 mW/m². This power density was 24% greater than an untreated anode, and similar to that obtained with an ammonia gas treatment previously shown to increase power. Increasing the nitrogen/carbon ratio to 3.8, however, decreased the power density to 707 mW/m². These results demonstrate that a small amount of nitrogen functionalization on the carbon cloth material is sufficient to enhance MFC performance, likely as a result of promoting bacterial adhesion to the surface without adversely affecting microbial viability or electron transfer to the surface.     

Layer-by-layer construction of graphene-based microbial fuel cell for improved power generation and methyl orange removal

Development of highly efficient anode is critical for enhancing the power output of microbial fuel cells (MFCs). The aim of this work is to investigate whether modification of carbon paper (CP) anode with graphene (GR) via layer-by-layer assembly technique is an effective approach to promote the electricity generation and methyl orange removal in MFCs. Using cyclic voltammetry and electrochemical impedance spectroscopy, the GR/CP electrode exhibited better electrochemical behavior. Scanning electron microscopy results revealed that the surface roughness of GR/CP increased, which was favorable for more bacteria to attach to the anode surface. The MFCs equipped with GR/CP anode achieved a stable maximum power density of 368 mW m^?2 under 1,000 Ω external resistance and a start time for the initial maximum voltage of 180 h, which were, respectively, 51 % higher and 31 % shorter than the corresponding values of the MFCs with blank anode. The anode and cathode polarization curves revealed negligible difference in cathode potentials but obviously difference in anode potentials, indicating that the GR-modified anode other than the cathode was responsible for the performance improvement of MFC. Meanwhile, compared with MFCs with blank anode, 11 % higher decolorization efficiency and 16 % higher the chemical oxygen demand removal rate were achieved in MFC with GR-modified anode during electricity generation. This study might provide an effective way to modify the anode for enhanced electricity generation and efficient removal of azo dye in MFCs.