Inverse Optical Cavity Design for Ultrabroadband Light Absorption Beyond the Conventional Limit in Low‐Bandgap Nonfullerene Acceptor–Based Solar Cells

In the subwavelength regime, several nanophotonic configurations have been proposed to overcome the conventional light trapping or light absorption enhancement limit in solar cells also known as the Yablonovitch limit. It has been recently suggested that establishing such limit should rely on computational inverse electromagnetic design instead of the traditional approach combining intuition and a priori known physical effect. In the present work, by applying an inverse full wave vector electromagnetic computational approach, a 1D nanostructured optical cavity with a new resonance configuration is designed that provides an ultrabroadband (≈450 nm) light absorption enhancement when applied to a 107 nm thick active layer organic solar cell based on a low‐bandgap (1.32 eV) nonfullerene acceptor. It is demonstrated computationally and experimentally that the absorption enhancement provided by such a cavity surpasses the conventional limit resulting from an ergodic optical geometry by a 7% average over a 450 nm band and by more than 20% in the NIR. In such a cavity configuration the solar cells exhibit a maximum power conversion efficiency above 14%, corresponding to the highest ever measured for devices based on the specific nonfullerene acceptor used.     

Light Trapping with Dielectric Scatterers in Single‐ and Tandem‐Junction Organic Solar Cells

Efficient dielectric scatterers based on a mixture of TiO₂ nanoparticles and polydimethylsiloxane are demonstrated for light trapping in semitransparent organic solar cells. An improvement of 80% in the photocurrent of an optimized semitransparent solar cell is achieved with the dielectric scatterer with ≈100% diffuse reflectance for wavelengths larger than 400 nm. For a parallel tandem solar cell, the dielectric scatterer generates 20% more photocurrent compared with a silver mirror beneath the cell; for a series tandem solar cell, the dielectric scatterer can be used as a photocurrent balancer between the subcells with different photoabsorbing materials. The power conversion efficiency of the tandem cell in series configuration with balanced photocurrent in the subcells exceeds that of an optimized standard solar cell with a reflective electrode. The characteristics of polydimethylsiloxane, such as flexibility and the ability to stick conformably to surfaces, also remain in the dielectric scatterers, which makes the demonstrated light trapping configuration highly suitable for large scale module manufacturing of roll‐to‐roll printed organic single‐ or tandem‐junction solar cells.     

Progress toward a biomimetic leaf: 4,000 h of hydrogen production by coating‐stabilized nongrowing photosynthetic Rhodopseudomonas palustris

Intact cells are the most stable form of nature's photosynthetic machinery. Coating‐immobilized microbes have the potential to revolutionize the design of photoabsorbers for conversion of sunlight into fuels. Multi‐layer adhesive polymer coatings could spatially combine photoreactive bacteria and algae (complementary biological irradiance spectra) creating high surface area, thin, flexible structures optimized for light trapping, and production of hydrogen (H₂) from water, lignin, pollutants, or waste organics. We report a model coating system which produced 2.08 ± 0.01 mmol H₂ m^?2 h^?1 for 4,000 h with nongrowing Rhodopseudomonas palustris, a purple nonsulfur photosynthetic bacterium. This adhesive, flexible, nanoporous Rps. palustris latex coating produced 8.24 ± 0.03 mol H₂ m^?2 in an argon atmosphere when supplied with acetate and light. A simple low‐pressure hydrogen production and trapping system was tested using a 100 cm² coating. Rps. palustris CGA009 was combined in a bilayer coating with a carotenoid‐less mutant of Rps. palustris (CrtI^?) deficient in peripheral light harvesting (LH2) function. Cryogenic field emission gun scanning electron microscopy (cryo‐FEG‐SEM) and high‐pressure freezing were used to visualize the microstructure of hydrated coatings. A light interaction and reactivity model was evaluated to predict optimal coating thickness for light absorption using the Kubelka‐Munk theory (KMT) of reflectance and absorptance. A two‐flux model predicted light saturation thickness with good agreement to observed H₂ evolution rate. A combined materials and modeling approach could be used for guiding cellular engineering of light trapping and reactivity to enhance overall photosynthetic efficiency per meter square of sunlight incident on photocatalysts. © 2010 American Institute of Chemical Engineers Biotechnol. Prog., 2010     

Light‐Driven BiVO4–C Fuel Cell with Simultaneous Production of H2O2

Photoelectrochemical (PEC) systems have been researched for decades due to their great promise to convert sunlight to fuels. The majority of the research on PEC has been using light to split water to hydrogen and oxygen, and its performance is limited by the need of additional bias. Another research direction on PEC using light, is to decompose organic materials while producing electricity. In this work, the authors report a new type of unassisted PEC system that uses light, water and oxygen to simultaneously produce electricity and hydrogen peroxide (H₂O₂) on both the photoanode and cathode, which is essentially a light‐driven fuel cell with H₂O₂ as the main product at the two electrodes, meanwhile achieving a maximum power density of 0.194 mW cm^‐2, an open circuit voltage of 0.61 V, and a short circuit current density of 1.09 mA cm^‐2. The electricity output can be further used as a sign for cell function when accompanied by a detector such as a light‐emitting diode (LED) light or a multimeter. This is the first work that shows H₂O₂ two‐side generation with a strict key factors study of the system, with a clear demonstration of electricity output ability using low‐cost earth abundant materials on both sides, which represents an exciting new direction for PEC systems.     

Rapid Layer‐Specific Annealing Enabled by Ultraviolet LED with Estimation of Crystallization Energy for High‐Performance Perovskite Solar Cells

A rapid layer‐specific annealing on perovskite active layer enabled by ultraviolet (UV) light‐emitting diode (LED) is demonstrated and efficiency close to 19% is achieved in a simple planar inverted structure ITO/PEDOT:PSS/MAPbI₃/PC₇₁BM/Al without any device engineering. These results demonstrate that if the UV dosage is well managed, UV light is capable of annealing perovskite into high‐quality film rather than simply damaging it. Different in principle from other photonic treatment techniques that can heat up and damage underlying films, the UV‐LED‐annealing method enables layer‐specific annealing because LED light source is able to provide a specific UV wavelength for maximum light absorption of target film. Moreover, the layer‐specific photonic treatment allows accurate estimation of the crystallization energy required to form perovskite film at device quality level.     

8.9% Single‐Stack Inverted Polymer Solar Cells with Electron‐Rich Polymer Nanolayer‐Modified Inorganic Electron‐Collecting Buffer Layers

Enhanced power conversion efficiency (PCE) is reported in inverted polymer solar cells when an electron‐rich polymer nanolayer (poly(ethyleneimine) (PEI)) is placed on the surface of an electron‐collecting buffer layer (ZnO). The active layer is made with bulk heterojunction films of poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]] (PTB7) and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM). The thickness of the PEI nanolayer is controlled to be 2 nm to minimize its insulating effect, which is confirmed by X‐ray photoelectron spectroscopy and optical absorption measurements. The Kelvin probe and ultraviolet photoelectron spectroscopy measurements demonstrate that the enhanced PCE by introducing the PEI nanolayer is attributed to the lowered conduction band energy of the ZnO layer via the formation of an interfacial dipole layer at the interfaces between the ZnO layer and the PEI nanolayer. The PEI nanolayer also improves the surface roughness of the ZnO layer so that the device series resistance can be noticeably decreased. As a result, all solar cell parameters including short circuit current density, open circuit voltage, fill factor, and shunt resistance are improved, leading to the PCE increase up to ≈8.9%, which is close to the best PCE reported using conjugated polymer electrolyte films.     

Improving Solar Cells’ Light Trapping by the Low Loss Interface Photonic Crystals

Improving the silicon layer’s optical absorption is a key research point for crystalline silicon based thin film solar cells. Light trapping is a method widely adopted to achieve this research purpose. In this paper, we propose low loss interface photonic crystals layer (IPC), which is sandwiched between the crystalline silicon layer and the cover layer. The low loss interface photonic crystals layer could boost the light trapping efficiency significantly. The mechanism is that the smaller refraction index difference between silicon layer and the low loss interface photonic crystals layer could reduce the light’s interface reflection. Taking advantage of the coupling calculation by optical and electrical simulations, solar cell’s absorption efficiency and electrical performance parameters are obtained. Compared with optimized reference group, the maximum output power of the proposed solar cell could be improved by 6.44%. The result indicates that the proposed low loss interface photonic crystals layer is applicable for light’s trapping in crystalline silicon thin film solar cells.

     

Diffraction‐Grated Perovskite Induced Highly Efficient Solar Cells through Nanophotonic Light Trapping

Achieving light harvesting is crucial for the efficiency of the solar cell. Constructing optical structures often can benefit from micro‐nanophotonic imprinting. Here, a simple and facile strategy is developed to introduce a large area grating structure into the perovskite‐active layer of a solar cell by utilizing commercial optical discs (CD‐R and DVD‐R) and achieve high photovoltaic performance. The constructed diffraction grating on the perovskite active layer realizes nanophotonic light trapping by diffraction and effectively suppresses carrier recombination. Compared to the pristine perovskite solar cells (PSCs), the diffraction‐grating perovskite devices with DVD obtain higher power conversion efficiency and photocurrent density, which are improved from 16.71% and 21.67 mA cm^?2 to 19.71% and 23.11 mA cm^?2. Moreover, the stability of the PSCs with diffraction‐grating‐structured perovskite active layer is greatly enhanced. The method can boost photonics merge into the remarkable perovskite materials for various applications.     

Plasmonic Backscattering Effect in High‐Efficient Organic Photovoltaic Devices

A universal strategy for efficient light trapping through the incorporation of gold nanorods on the electron transport layer (rear) of organic photovoltaic devices is demonstrated. Utilizing the photons that are transmitted through the active layer of a bulk heterojunction photovoltaic device and would otherwise be lost, a significant enhancement in power conversion efficiency (PCE) of poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)]:phenyl‐C₇₁‐butyric acid methyl ester (PCDTBT:PC₇₁BM) and poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b] thiophenediyl]] (PTB7):PC₇₁BM by ≈13% and ≈8%, respectively. PCEs over 8% are reported for devices based on the PTB7:PC₇₁BM blend. A comprehensive optical and electrical characterization of our devices to clarify the influence of gold nanorods on exciton generation, dissociation, charge recombination, and transport inside the thin film devices is performed. By correlating the experimental data with detailed numerical simulations, the near‐field and far‐field scattering effects are separated of gold nanorods (Au NRs), and confidently attribute part of the performance enhancement to the enhanced absorption caused by backscattering. While, a secondary contribution from the Au NRs that partially protrude inside the active layer and exhibit strong near‐fields due to localized surface plasmon resonance effects is also observed but is minor in magnitude. Furthermore, another important contribution to the enhanced performance is electrical in nature and comes from the increased charge collection probability.     

Targeting Ideal Dual‐Absorber Tandem Water Splitting Using Perovskite Photovoltaics and CuInxGa1‐xSe2 Photocathodes

Efficient sunlight‐driven water splitting devices can be achieved by pairing two absorbers of different optimized bandgaps in an optical tandem design. With tunable absorption ranges and cell voltages, organic–inorganic metal halide perovskite solar cells provide new opportunities for tailoring top absorbers for such devices. In this work, semitransparent perovskite solar cells are developed for use as the top cell in tandem with a smaller bandgap photocathode to enable panchromatic harvesting of the solar spectrum. A new CuIn_xGa_1‐xSe₂ multilayer photocathode is designed, exhibiting excellent performance for photoelectrochemical water reduction and representing a near‐ideal bottom absorber. When pairing it below a semitransparent CH₃NH₃PbBr₃‐based solar cell, a solar‐to‐hydrogen efficiency exceeding 6% is achieved, the highest value yet reported for a photovoltaic–photoelectrochemical device utilizing a single‐junction solar cell as the bias source under one sun illumination. The analysis shows that the efficiency can reach more than 20% through further optimization of the perovskite top absorber.     

Photovoltaic Device with over 5% Efficiency Based on an n‐Type Ag2ZnSnSe4 Absorber

The kesterite material Cu₂ZnSn(S,Se)₄ (CZTSSe) is an attractive earth‐abundant semiconductor for photovoltaics. However, the power conversion efficiency is limited by a large density of I–II antisite defects, which cause severe band tailing and open‐circuit voltage loss. Ag₂ZnSnSe₄ (AZTSe) is a promising alternative to CZTSSe with a substantially lower I–II antisite defect density and smaller band tailing. AZTSe is weakly n‐type, and this study reports for the first time on how the carrier density is impacted by stoichiometry. This study presents the first‐ever photovoltaic device based on AZTSe, which exhibits an efficiency of 5.2%, which is the highest value reported for an n‐type thin‐film absorber. Due to the weakly n‐type nature of the absorber, a new architecture is employed (SnO:F/AZTSe/MoO₃/ITO) to replace conventional contacts and buffer materials. Using this platform, it is shown that the band tailing parameter in AZTSe more closely resembles that of CIGSe than CZTSSe, underscoring the strong promise of this absorber. In demonstrating the ability to collect photogenerated carriers from AZTSe, this study paves the way for novel thin‐film heterojunction architectures where light absorption in the n‐type device layer can supplement absorption in the p‐type layer as opposed to producing a net optical loss.     

Strong Visible‐Light Absorption and Hot‐Carrier Injection in TiO2/SrRuO3 Heterostructures

Correlated electron oxides prove a diverse landscape of exotic materials' phenomena and properties. One example of such a correlated oxide material is strontium ruthenate (SrRuO₃) which is known to be a metallic itinerant ferromagnet and for its widespread utility as a conducting electrode in oxide heterostructures. We observe that the complex electronic structure of SrRuO₃ is also responsible for unexpected optical properties including high absorption across the visible spectrum (commensurate with a low band gap semiconductor) and remarkably low reflection compared to traditional metals. By coupling this material to a wide band gap semiconductor (TiO₂) we demonstrate dramatically enhanced visible light absorption and large photocatalytic activities. The devices function by photo‐excited hot‐carrier injection from the SrRuO₃ to the TiO₂ and the effect is enhanced in thin films due to electronic structure changes. This observation provides an exciting new approach to the challenge of designing visible‐light photosensitive materials.     

Interface Engineering for Highly Efficient and Stable Planar p‐i‐n Perovskite Solar Cells

Organic‐inorganic halide perovskite materials have become a shining star in the photovoltaic field due to their unique properties, such as high absorption coefficient, optimal bandgap, and high defect tolerance, which also lead to the breathtaking increase in power conversion efficiency from 3.8% to over 22% in just seven years. Although the highest efficiency was obtained from the TiO₂ mesoporous structure, there are increasing studies focusing on the planar structure device due to its processibility for large‐scale production. In particular, the planar p‐i‐n structure has attracted increasing attention on account of its tremendous advantages in, among other things, eliminating hysteresis alongside a competitive certified efficiency of over 20%. Crucial for the device performance enhancement has been the interface engineering for the past few years, especially for such planar p‐i‐n devices. The interface engineering aims to optimize device properties, such as charge transfer, defect passivation, band alignment, etc. Herein, recent progress on the interface engineering of planar p‐i‐n structure devices is reviewed. This review is mainly focused on the interface design between each layer in p‐i‐n structure devices, as well as grain boundaries, which are the interfaces between polycrystalline perovskite domains. Promising research directions are also suggested for further improvements.     

Dramatic Enhancement of CO2 Photoreduction by Biodegradable Light‐Management Paper

Photocatalytic reduction of CO₂ with H₂O vapor is gaining increased interest because it is a promising “green chemistry” route for the direct conversion of CO₂ to value‐added chemicals driven by solar energy. To increase the efficiency of photocatalytic conversion, most efforts are made by exploring various photocatalysts while little effort on advanced light management. For the first time, it is demonstrated that bio‐degradable transparent paper with excellent light diffusivity can effectively enhance the light utilization of photocatalytic reactions when attached on the device surface, and thus greatly increase the conversion efficiency. As a proof‐of‐concept, a graphitic carbon nitride (g‐C₃N₄) photocatalyst with transparent paper attached, exhibited 1.5 times higher photocatalytic activity than bare g‐C₃N₄ in the reduction of CO₂ under visible light irradiation. The improved catalytic performance can be ascribed to the (1) refractive index matching and (2) enhanced light absorption via prolonged light traveling path in transparent paper, which decreases the light reflection at surface and traps the absorbed light inside, leading to an increased light absorption at the active layer of the device. The transparent paper with a controllable light management behavior has an unprecedented potential for applications in photocatalysis as a general method for improved light utilization.     

Ordered Nanoscale Heterojunction Architecture for Enhanced Solution‐Based CuInGaS2 Thin Film Solar Cell Performance

Nanopatterned CuInGaS₂ (CIGS) thin films synthesized by a sol‐gel‐based solution method and a nanoimprint lithography technique to achieve simultaneous photonic and electrical enhancements in thin film solar cell applications are demonstrated. The interdigitated CIGS nanopatterns in adjacent CdS layer form an ordered nanoscale heterojunction of optical contrast to create a light trapping architecture. This architecture concomitantly leads to increased junction area between the p‐CIGS/n‐CdS interface, and thereby influences effective charge transport. The electron beam induced current and capacitance–voltage characterization further supports the large carrier collection area and small depletion region of the nanopatterned CIGS solar cell devices. This strategic geometry affords localization of incident light inside and between the nanopatterns, where created excitons are easily dissociated, and it leads to the enhanced current generation of absorbed light. Ultimately, this approach improves the efficiency of the nanopatterned CIGS solar cell by 55% compared to its planar counterpart, and offers the possibility of simultaneous management for absorption and charge transport through a nanopatterning process.     

Designing 1,5‐Naphthyridine‐2,6‐dione‐Based Conjugated Polymers for Higher Crystallinity and Enhanced Light Absorption to Achieve 9.63% Efficiency Polymer Solar Cells

Highly crystalline conjugated polymers represent a key material for producing high‐performance thick‐active‐layer polymer solar cells (PSCs). However, despite their potential, a limited number of crystalline polymers are used in PSCs because of the lack of highly coplanar acceptor building blocks and insufficient light absorptivity (α < 10⁵) of most donor (D)–acceptor (A)‐type polymers. This study reports a series of novel 3,7‐di(thiophen‐2‐yl)‐1,5‐naphthyridine‐2,6‐dione (NTDT) acceptor‐based conjugated polymers, PNTDT‐2T, PNTDT‐TT, and PNTDT‐2F2T, synthesized with 2,2′‐bithiophene (2T), thieno[3,2‐b]thiophene (TT), and 3,3′‐difluoro‐2,2′‐bithiophene (2F2T) donor units, respectively. PNTDT‐2F2T exhibits superior polymer crystallinity and a much higher absorption coefficient than those of PNTDT‐2T or PNTDT‐TT because of adequate matching between highly coplanar A (NTDT) and D (2F2T) building blocks. A bulk heterojunction solar cell based on PNTDT‐2F2T exhibits a power conversion efficiency of up to 9.63%, with a high short circuit current of 18.80 mA cm^?2 and fill factor of 0.70, when a thick active layer (>200 nm) is used, without postfabrication hot processing. The findings demonstrate that the polymer crystallinity and absorption coefficient can be effectively controlled by selecting appropriate D and A building blocks, and that NTDT is a novel and versatile A building block for highly efficient thick‐active‐layer PSCs.     

High‐Performance Ta2O5/Al‐Doped Ag Electrode for Resonant Light Harvesting in Efficient Organic Solar Cells

A efficient indium tin oxide (ITO)‐free transparent electrode based on an improved Ag film is designed by introducing small amount of Al during co‐deposition, producing ultrathin and smooth Ag film with low loss. A transparent electrode as thin as 4 nm is achieved by depositing the film on top of Ta₂O₅ layer, and organic solar cells based on such ultrathin electrode are built, producing power conversion efficiency over 7%. The device efficiency can be optimized by simply tuning Ta₂O₅ layer thickness external to the organic photovoltaic (OPV) structure to create an optical cavity resonance inside the photoactive layer. Therefore Ta₂O₅/Al‐doped Ag films function as a high‐performance electrode with high transparency, low resistance, improved photon management capability and mechanical flexibility.     

Research Progress on Negative Electrodes for Practical Li‐Ion Batteries: Beyond Carbonaceous Anodes

Research activities related to the development of negative electrodes for construction of high‐performance Li‐ion batteries (LIBs) with conventional cathodes such as LiCoO₂, LiFePO₄, and LiMn₂O₄ are described. The anode materials are classified in to three main categories, insertion, conversion, and alloying type, based on their reactivity with Li. Although numerous materials have been proposed (i.e., for half‐cell assembly), few of them have reached commercial applications, apart from graphite, Li₄Ti₅O₁₂, Si, and Sn‐Co‐C. This clearly demonstrates that full‐cell studies are desperately needed rather than just characterizing materials in half‐cell assemblies. Additionally, the performance of such anodes in practical Li‐ion configurations (full‐cell) is much more important than merely proposing materials for LIBs. Irreversible capacity loss, huge volume variation, unstable solid electrolyte interface layer formation, and poor cycleability are the main issues for conversion and alloy type anodes. This review addresses how best to circumvent the mentioned issues during the construction of Li‐ion cells and the future prospects of such anodes are described in detail.     

Ultra‐High Voltage Multijunction Organic Solar Cells for Low‐Power Electronic Applications

Low power electronics are an ideal application for organic photovoltaics (OPV) where a low‐cost OPV device can be integrated directly with a battery to provide a constant power source. We demonstrate ultra‐high voltage small molecule multijunction devices with open circuit voltage (V_OC) values of up to 7V. Optical modelling is employed to aid the optimisation of the complex multi‐layer stacks and ensure current balancing is achieved between sub‐cells, and optimised multijunction devices show power conversion efficiencies of up to 3.4% which is a modest increase over the single junction devices. Sub‐cell donor/acceptor pairs of boron subphthalocyanine chloride (SubPc)/fullerene (C₆₀) and SubPc/Cl₆‐SubPc were selected both for their high V_OC in order to minimise the required number of junctions, but also for their absorption overlap to reduce the spectral dependence of the device performance. As a result, the devices are shown to directly charge a micro‐energy cell type battery under both low illumination intensity white light and monochromatic illumination.     

Efficient Indium‐Doped TiOx Electron Transport Layers for High‐Performance Perovskite Solar Cells and Perovskite‐Silicon Tandems

In addition to a good perovskite light absorbing layer, the hole and electron transport layers play a crucial role in achieving high‐efficiency perovskite solar cells. Here, a simple, one‐step, solution‐based method is introduced for fabricating high quality indium‐doped titanium oxide electron transport layers. It is shown that indium‐doping improves both the conductivity of the transport layer and the band alignment at the ETL/perovskite interface compared to pure TiO₂, boosting the fill‐factor and voltage of perovskite cells. Using the optimized transport layers, a high steady‐state efficiency of 17.9% for CH₃NH₃PbI₃‐based cells and 19.3% for Cs_0.05(MA_0.17FA_0.83)_0.95Pb(I_0.83Br_0.17)₃‐based cells is demonstrated, corresponding to absolute efficiency gains of 4.4% and 1.2% respectively compared to TiO₂‐based control cells. In addition, a steady‐state efficiency of 16.6% for a semi‐transparent cell is reported and it is used to achieve a four‐terminal perovskite‐silicon tandem cell with a steady‐state efficiency of 24.5%.