Nanofiber‐Based Bulk‐Heterojunction Organic Solar Cells Using Coaxial Electrospinning

Nanofibers consisting of the bulk heterojunction organic photovoltaic (BHJ–OPV) electron donor–electron acceptor pair poly(3‐hexylthiophene):phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) are produced through a coaxial electrospinning process. While P3HT:PCBM blends are not directly electrospinnable, P3HT:PCBM‐containing fibers are produced in a coaxial fashion by utilizing polycaprolactone (PCL) as an electrospinnable sheath material. Pure P3HT:PCBM fibers are easily obtained after electrospinning by selectively removing the PCL sheath with cyclopentanone (average diameter 120 ± 30 nm). These fibers are then incorporated into the active layer of a BHJ–OPV device, which results in improved short‐circuit current densities, fill factors, and power‐conversion efficiencies (PCE) as compared to thin‐film devices of identical chemical composition. The best‐performing fiber‐based devices exhibit a PCE of 4.0%, while the best thin‐film devices have a PCE of 3.2%. This increase in device performance is attributed to the increased in‐plane alignment of P3HT polymer chains on the nanoscale, caused by the electrospun fibers, which leads to increased optical absorption and subsequent exciton generation. This methodology for improving device performance of BHJ–OPVs could also be implemented for other electron donor–electron acceptor systems, as nanofiber formation is largely independent of the PV material.     

Twist and Degrade—Impact of Molecular Structure on the Photostability of Nonfullerene Acceptors and Their Photovoltaic Blends

Nonfullerene acceptors (NFAs) dominate organic photovoltaic (OPV) research due to their promising efficiencies and stabilities. However, there is very little investigation into the molecular processes of degradation, which is critical to guiding design of novel NFAs for long‐lived, commercially viable OPVs. Here, the important role of molecular structure and conformation in NFA photostability in air is investigated by comparing structurally similar but conformationally different promising NFAs: planar O‐IDTBR and nonplanar O‐IDFBR. A three‐phase degradation process is identified: i) initial photoinduced conformational change (i.e., torsion about the core–benzothiadiazole dihedral), induced by noncovalent interactions with environmental molecules, ii) followed by photo‐oxidation and fragmentation, leading to chromophore bleaching and degradation product formation, and iii) finally complete chromophore bleaching. Initial conformational change is a critical prerequisite for further degradation, providing fundamental understanding of the relative stability of IDTBR and IDFBR, where the already twisted IDFBR is more prone to degradation. When blended with the donor polymer poly(3‐hexylthiophene), both NFAs exhibit improved photostability while the photostability of the polymer itself is significantly reduced by the more miscible twisted NFA. The findings elucidate the important role of NFA molecular structure in photostability of OPV systems, and provide vital insights into molecular design rules for intrinsically photostable NFAs.     

SrTiO3/Al2O3‐Graphene Electron Transport Layer for Highly Stable and Efficient Composites‐Based Perovskite Solar Cells with 20.6% Efficiency

For practical use of perovskite solar cells (PSCs) the instability issues of devices, attributed to degradation of perovskite molecules by moisture, ions migration, and thermal‐ and light‐instability, have to be solved. Herein, highly efficient and stable PSCs based on perovskite/Ag‐reduced graphene oxide (Ag‐rGO) and mesoporous Al₂O₃/graphene (mp‐AG) composites are reported. The mp‐AG composite is conductive with one‐order of magnitude higher mobility than mp‐TiO₂ and used for electron transport layer (ETL). Compared to the mp‐TiO₂ ETL based cells, the champion device based on perovskite/Ag‐rGO and SrTiO₃/mp‐AG composites shows overall a best performance (i.e., V_OC = 1.057 V, J_SC = 25.75 mA cm^?2, fill factor (FF) = 75.63%, and power conversion efficiency (PCE) = 20.58%). More importantly, the champion device without encapsulation exhibits not only remarkable thermal‐ and photostability but also long‐term stability, retaining 97–99% of the initial values of photovoltaic parameters and sustaining ≈93% of initial PCE over 300 d under ambient conditions.     

Breaking the 10% Efficiency Barrier in Organic Photovoltaics: Morphology and Device Optimization of Well‐Known PBDTTT Polymers

With the advances in organic photovoltaics (OPVs), the invention of model polymers with superior properties and wide applicability is of vital importance to both the academic and industrial communities. The recent inspiring advances in OPV research have included the emergence of poly(benzodithiophene‐co‐thieno[3,4‐b]thiophene) (PBDTTT)‐based materials. Through the combined efforts on PBDTTT polymers, over 10% efficiencies have been realized recently in various types of OPV devices. This review attempts to critically summarize the recent advances with respect to five well‐known PBDTTT polymers and their design considerations, basic properties, photovoltaic performance, as well as device application in conventional, inverted, tandem solar cells. These PBDTTT polymers also make great contributions to the rapid advances in the field of emerging ternary blends and fullerene‐free OPVs with top performances. Addtionally, new challenges in developing novel photovoltaic polymers with more superior properties are prospected. More importantly, the research of highly efficient PBDTTT‐based polymers provides useful insights and builds fundamentals for new types of OPV applications with various architectures.     

Compatibility of PTB7 and [70]PCBM as a Key Factor for the Stability of PTB7:[70]PCBM Solar Cells

The rapid degradation of organic photovoltaic (OPV) devices compared to conventional inorganic solar cells is one of the critical issues that have to be solved in order to make OPV a competitive commercial technology. The understanding of the fundamental mechanisms that reduce the power conversion efficiency (PCE) over time is beneficial for the design of new materials with enhanced stability. This paper focuses on bulk heterojunction organic solar cells based on thieno [3,4‐b] thiophene‐alt‐benzodithiophene (PTB7) mixed with [6,6]‐phenyl‐C71‐butyric acid methyl esther ([70]PCBM). In spite of being promising in terms of PCE, devices based on this blend are unstable and have a short lifetime. When exposed to light in inert atmosphere, the PCE drops by 15% in less than 1 h and by 35% in 8 h; this degradation is induced by the ultraviolet (UV) part of the spectrum. This paper analyzes the effect induced by UV light on the transport of charges in PTB7:[70]PCBM. Contrary to expectations, the electron transport shows evidence of trapping, while the transport of holes appears unaffected. Furthermore, it is proven that the loss of PCE is due to a reaction between PTB7 and [70]PCBM, while the intrinsic instability of the polymer plays a marginal role.     

High‐Performance Tandem Organic Solar Cells Using HSolar as the Interconnecting Layer

Tandem structure provides a practical way to realize high efficiency organic photovoltaic cells, it can be used to extend the wavelength coverage for light harvesting. The interconnecting layer (ICL) between subcells plays a critical role in the reproducibility and performance of tandem solar cells, yet the processability of the ICL has been a challenge. In this work the fabrication of highly reproducible and efficient tandem solar cells by employing a commercially available material, PEDOT:PSS HTL Solar (HSolar), as the hole transporting material used for the ICL is reported. Comparing with the conventional PEDOT:PSS Al 4083 (c‐PEDOT), HSolar offers a better wettability on the underlying nonfullerene photoactive layers, resulting in better charge extraction properties of the ICL. When FTAZ:IT‐M and PTB7‐Th:IEICO‐4F are used as the subcells, a power conversion efficiency (PCE) of 14.7% is achieved in the tandem solar cell. To validate the processability of these tandem solar cells, three other research groups have successfully fabricated tandem devices using the same recipe and the highest PCE obtained is 16.1%. With further development of donor polymers and device optimization, the device simulation results show that a PCE > 22% can be realized in tandem cells in the near future.     

The Importance of Pendant Groups on Triphenylamine‐Based Hole Transport Materials for Obtaining Perovskite Solar Cells with over 20% Efficiency

Tremendous progress has recently been achieved in the field of perovskite solar cells (PSCs) as evidenced by impressive power conversion efficiencies (PCEs); but the high PCEs of >20% in PSCs has so far been mostly achieved by using the hole transport material (HTM) spiro‐OMeTAD; however, the relatively low conductivity and high cost of spiro‐OMeTAD significantly limit its potential use in large‐scale applications. In this work, two new organic molecules with spiro[fluorene‐9,9′‐xanthene] (SFX)‐based pendant groups, X26 and X36, have been developed as HTMs. Both X26 and X36 present facile syntheses with high yields. It is found that the introduced SFX pendant groups in triphenylamine‐based molecules show significant influence on the conductivity, energy levels, and thin‐film surface morphology. The use of X26 as HTM in PSCs yields a remarkable PCE of 20.2%. In addition, the X26‐based devices show impressive stability maintaining a high PCE of 18.8% after 5 months of aging in controlled (20%) humidity in the dark. We believe that X26 with high device PCEs of >20% and simple synthesis show a great promise for future application in PSCs, and that it represents a useful design platform for designing new charge transport materials for optoelectronic applications.     

Design of Star-Shaped Trimer Acceptors for High-Performance (Efficiency > 19%), Photostable,and Mechanically Robust Organic Solar Cells

High power conversion efficiency (PCE), long-term stability, and mechanical robustness are prerequisites for the commercial applications of organic solar cells (OSCs). In this study, a new star-shaped trimer acceptor (TYT-S) is developed and high-performance OSCs with a PCE of 19.0%, high photo-stability (t_80% lifetime = 2600 h under 1-sun illumination), and mechanical robustness with a crack-onset strain (COS) of 21.6% are achieved. The isotropic molecular structure of TYT-S affords efficient multi-directional charge transport and high electron mobility. Furthermore, its amorphous structure prevents the formation of brittle crystal-to-crystal interfaces, significantly enhancing the mechanical properties of the OSC. As a result, the TYT-S-based OSCs demonstrate a significantly higher PCE (19.0%) and stretchability (COS = 21.6%) than the linear-shaped trimer acceptor (TYT-L)-based OSCs (PCE = 17.5% and COS = 6.4%) and the small-molecule acceptor (MYT)-based OSCs (PCE = 16.5% and COS = 1.3%). In addition, the increased molecular size of TYT-S, relative to that of MYT and dimer (DYT), suppresses the diffusion kinetics of the acceptor molecules, substantially improving the photostability of the OSCs. Finally, to effectively demonstrate the potential of TYT-S, intrinsically stretchable (IS)-OSCs are constructed. The TYT-S-based IS-OSCs exhibit high device stretchability (strain at PCE_80% = 31%) and PCE of 14.4%.     

Carbon: The Ultimate Electrode Choice for Widely Distributed Polymer Solar Cells

As mass‐produced, low‐cost organic electronics enter our everyday lives, so does the waste from them. The challenges associated with end‐of‐life management must be addressed by careful design and carbon‐based electrodes are central to these developments. Here, the reproducible production of vacuum‐, indium tin oxide (ITO)‐, and silver‐free solar cells in a fully packaged form using only roll‐to‐roll processing is reported. Replacing silver with carbon as electrode material significantly lowers the manufacturing cost and makes the organic photovoltaic (OPV) modules environmentally safe while retaining their flexibility, active area efficiency, and stability. The substitution of silver with carbon does not affect the roll‐to‐roll manufacturing of the modules and allows for the same fast printing and coating. The use of carbon as electrode material is one step closer to the wide release of low‐cost plastic solar cells and opens the door to new possible applications where silver recycling is not manageable.     

Long‐Lasting Nanophosphors Applied to UV‐Resistant and Energy Storage Perovskite Solar Cells

Recently, considerable progress is achieved in lab prototype perovskite solar cells (PSCs); however, the stability of outdoor applications of PSCs remains a challenge due to the high sensitivity of perovskite material under moist and ultraviolet (UV) light conditions. In this work, the UV photostability of PSC devices is improved by incorporating a photon downshifting layer—SrAl₂O₄: Eu²⁺, Dy³⁺ (SAED)—prepared using the pulsed laser deposition approach. Light‐induced deep trap states in the photoactive layer are depressed, and UV light‐induced device degradation is inhibited after the SAED modification. Optimized power conversion efficiency (PCE) of 17.8% is obtained through the enhanced light harvesting and reduced carrier recombination provided by SAED. More importantly, a solar energy storage effect due to the long‐persistent luminescence of SAED is obtained after light illumination is turned off. The introduction of downconverting material with long‐persistent luminescence in PSCs not only represents a new strategy to improve PCE and light stability by photoconversion from UV to visible light but also provides a new paradigm for solar energy storage.     

Universal Design Principles for Cascade Heterojunction Solar Cells with High Fill Factors and Internal Quantum Efficiencies Approaching 100%

Cascade heterojunction (CHJ) organic solar cells have recently emerged as an alternative to conventional bulk heterojunctions and series‐connected tandems due to their significant promise for high internal quantum efficiency (IQE) and broad spectral coverage. However, CHJ devices thus far have also exhibited poor fill factor (FF), resulting in minimal enhancements (or even decreases) in power conversion efficiency (PCE) when compared with single heterojunction (SHJ) cells. In this study, the major variables controlling the CHJ maximum power point and FF are determined using a combinatorial approach. By matching the maximum power point voltage (V_MPP) of the constituent parallel‐connected heterojunctions (subjunctions) and minimizing the injection barriers intrinsic to CHJs, high FF and PCE can be achieved. Optimized CHJ devices are demonstrated with >99% IQE in the interlayer and a 46% increase in PCE compared to a SHJ reference (4.1% versus 2.8%). Devices with a transparent exciton dissociation layer (EDL)/interlayer/acceptor structure are employed, such that each CHJ has absorption efficiency identical to its interlayer/acceptor SHJ counterpart. Using these results, a clear map of performance as a function of material parameters is developed, providing straightforward, universal design rules to guide future engineering of molecules and layer architectures for CHJ organic photovoltaic devices.     

Simultaneous Improved Performance and Thermal Stability of Planar Metal Ion Incorporated CsPbI2Br All‐Inorganic Perovskite Solar Cells Based on MgZnO Nanocrystalline Electron Transporting Layer

The high thermal stability and facile synthesis of CsPbI₂Br all‐inorganic perovskite solar cells (AI‐PSCs) have attracted tremendous attention. As far as electron‐transporting layers (ETLs) are concerned, low temperature processing and reduced interfacial recombination centers through tunable energy levels determine the feasibility of the perovskite devices. Although the TiO₂ is the most popular ETL used in PSCs, its processing temperature and moderate electron mobility hamper the performance and feasibility. Herein, the highly stable, low‐temperature processed MgZnO nanocrystal‐based ETLs for dynamic hot‐air processed Mn²⁺ incorporated CsPbI2Br AI‐PSCs are reported. By holding its regular planar “n–i–p” type device architecture, the MgZnO ETL and poly(3‐hexylthiophene‐2,5‐diyl) hole transporting layer, 15.52% power conversion efficiency (PCE) is demonstrated. The thermal‐stability analysis reveals that the conventional ZnO ETL‐based AI‐PSCs show a serious instability and poor efficiency than the Mg²⁺ modified MgZnO ETLs. The photovoltaic and stability analysis of this improved photovoltaic performance is attributed to the suitable wide‐bandgap, low ETL/perovskite interface recombination, and interface stability by Mg²⁺ doping. Interestingly, the thermal stability analysis of the unencapsulated AI‐PSCs maintains >95% of initial PCE more than 400 h at 85 °C for MgZnO ETL, revealing the suitability against thermal degradation than conventional ZnO ETL.     

Efficient Defect Passivation for Perovskite Solar Cells by Controlling the Electron Density Distribution of Donor‐π‐Acceptor Molecules

Organic–inorganic hybrid perovskite solar cells (PSCs) are a promising photovoltaic technology that has rapidly developed in recent years. Nevertheless, a large number of ionic defects within perovskite absorber can serve as non‐radiative recombination center to limit the performance of PSCs. Here, organic donor‐π‐acceptor (D‐π‐A) molecules with different electron density distributions are employed to efficiently passivate the defects in the perovskite films. The X‐ray photoelectron spectroscopy (XPS) analysis shows that the strong electron donating N,N‐dibutylaminophenyl unit in a molecule causes an increase in the electron density of the passivation site that is a carboxylate group, resulting in better binding with the defects of under‐coordinated Pb²⁺ cations. Carrier lifetime in the perovskite films measured by the time‐resolved photoluminescence spectrum is also prolonged by an increase in donation ability of the D‐π‐A molecules. As a consequence, these benefits contribute to an increase of 80 mV in the open circuit voltage of the devices, enabling a maximum power conversion efficiency (PCE) of 20.43%, in comparison with PCE of 18.52% for the control device. The authors' findings provide a novel strategy for efficient defect passivation in the perovskite solar cells based on controlling the electronic configuration of passivation molecules.     

Interfaces in Perovskite Solar Cells

Rapid improvement in photoconversion efficiency (PCE) of solution processable organometallic hybrid halide based perovskite solar cells (PSCs) have taken the photovoltaic (PV) community with a surprise and has extended their application in other electronic devices such as light emitting diodes, photo detectors and batteries. Together with efforts to push the PCE of PSCs to record values >22% – now at par with that of crystalline silicon solar cells – origin of their PV action and underlying physical processes are also deeply investigated worldwide in diverse device configurations. A typical PSC consists of a perovskite film sandwiched between an electron and a hole selective contact thereby creating ESC/perovskite and perovskite/HSC interfaces, respectively. The selective contacts and their interfaces determine properties of perovskite layer and also control the performance, origin of PV action, open circuit voltage, device stability, and hysteresis in PSCs. Herein, we define ideal charge selective contacts, and provide an overview on how the choice of interfacing materials impacts charge accumulation, transport, transfer/recombination, band‐alignment, and electrical stability in PSCs. We then discuss device related considerations such as morphology of the selective contacts (planar or mesoporous), energetics and electrical properties (insulating and conducting), and its chemical properties (organic vs inorganic). Finally, the outlook highlights key challenges and future directions for a commercially viable perovskite based PV technology.     

Efficient Hybrid Tandem Solar Cells Based on Optical Reinforcement of Colloidal Quantum Dots with Organic Bulk Heterojunctions

While colloidal quantum dot photovoltaic devices (CQDPVs) can achieve a power conversion efficiency (PCE) of ≈12%, their insufficient optical absorption in the near‐infrared (NIR) regime impairs efficient utilization of the full spectrum of visible light. Here, high‐efficiency, solution‐processed, hybrid series, tandem photovoltaic devices are developed featuring CQDs and organic bulk heterojunction (BHJ) photoactive materials for front‐ and back‐cells, respectively. The organic BHJ back‐cell efficiently harvests the transmitted NIR photons from the CQD front‐cell, which reinforces the photon‐to‐current conversion at 350–1000 nm wavelengths. Optimizing the short‐circuit current density balance of each sub‐cell and creating a near ideal series connection using an intermediate layer achieve a PCE (12.82%) that is superior to that of each single‐junction device (11.17% and 11.02% for the CQD and organic BHJ device, respectively). Notably, the PCE of the hybrid tandem device is the highest among the reported CQDPVs, including single‐junction devices and tandem devices. The hybrid tandem device also exhibits almost negligible degradation after air storage for 3 months. This study suggests a potential route to improve the performance of CQDPVs by proper hybridization with NIR‐absorbing photoactive materials.     

Role of Stress Factors on the Adhesion of Interfaces in R2R Fabricated Organic Photovoltaics

The role of the common stress factors such as high temperature, humidity, and UV irradiation on interface adhesion of roll‐to‐roll fabricated organic photovoltaic (OPV) devices is investigated. The samples range from bare front electrodes to complete devices. It is shown that applying single stress or combinations of stresses onto the samples variably affect the adhesion properties of the different interfaces in the OPV device. It is revealed that while the exposure of the complete devices to the stresses results in the loss of photovoltaic performance, some interfaces in the devices present improved adhesion properties. Depth profiling analysis on the fractured samples reveals interdiffusion of layers in the structure, which results in the increase of adhesion and change of the debond path. It is shown that through diffusion and intermixing of internal interfaces coupled stresses can increase the adhesion of OPV interfaces by over tenfold. The results are additionally compared to the photovoltaic performance of the complete devices.     

Complete Demonstration of the Valence Electronic Structure Inside a Practical Organic Solar Cell Probed by Low Energy Photoemission

The complete electronic structure inside a practical organic photovoltaic (OPV) device consisting of a trilayer structure of copper‐phthalocyanine (CuPc), fullerene (C₆₀), and bathocuproine (BCP) is demonstrated using low‐energy ultraviolet photoelectron spectroscopy (LE‐UPS) and photoelectron yield spectroscopy (PYS). The molecular orbital energy alignment and electrostatic potential distribution throughout the entire device is illustrated based on the LE‐UPS results. A favorable potential gradient to carry the photogenerated holes and electrons is manifested to be built spontaneously in the CuPc and BCP layers, respectively. Furthermore, the ultrahigh sensitivity measurements of LE‐UPS clearly unveil the distributions of faint density‐of‐states in the energy‐gap region in the organic films. Substantially barrierless contacts to both electrodes are fulfilled by the existence of these gap states. The electronic structure under simulated sunlight illumination is examined for the purpose of elucidating the electronic structures inside the working devices in the open‐circuit condition. These results indicate experimentally the electronic functionalities of each organic material, in particular of the BCP buffer layer, on the cell efficiency.     

Carrier‐Selectivity‐Dependent Charge Recombination Dynamics in Organic Photovoltaic Cells with a Ferroelectric Blend Interlayer

Interfacial energetics determines the performance of organic photovoltaic (OPV) cells based on a thin film of organic semiconductor blends. Here, an approach to modulating the “carrier selectivity” at the charge collecting interfaces and the consequent variations in the nongeminate charge carrier recombination dynamics in OPV devices are demonstrated. A ferroelectric blend interfacial layer composed of a solution‐processable ferroelectric poly­mer and a wide bandgap semiconductor is introduced as a tunable electron selective layer in inverted OPV devices with non‐Ohmic contact electrodes. The direct rendering of dipole alignment within the ferroelectric blend layer is found to increase the carrier selectivity of the charge collecting interfaces up to two orders of magnitude. Transient photovoltaic analyses reveal that the increase of carrier selectivity significantly reduces the diffusion and recombination among minority carriers in the vicinity of the electrodes, giving rise to the 85% increased charge carrier lifetime. Furthermore, the carrier‐selective charge extraction leads to the constitution of the internal potential within the devices, even with energetically identical cathodes and anodes. With these carrier‐selectivity‐controlled interlayers, the devices based on various photoactive materials commonly display significant increments in the device performances, especially with the high fill factor of up to 0.76 under optimized conditions.     

Photochemical Transformations in Fullerene and Molybdenum Oxide Affect the Stability of Bilayer Organic Solar Cells

Thin films of fullerene C₆₀ and molybdenum oxide (MoO₃) are ubiquitously used as the electron acceptor material and hole extraction interfacial layer for the fabrication of organic photovoltaic (OPV) cells. It is well known that light exposure induces color changes in MoO₃ (photochromism) and the formation of intermolecular bonds between C₆₀ molecules (photopolymerization). The influence of these photoinduced reactions on the long‐term stability of OPV cells, however, has not previously been studied in detail. Here, a study and discussion of the early (<5 days) aging mechanisms occurring in illuminated ITO/MoO₃/organic cyanine dye/C₆₀/Alq₃/Ag bilayer solar cells under nitrogen atmosphere is presented. A degradation process at the organic heterojunction is identified and the formation of Mo⁵⁺ species during illumination is found to adversely affect cell behavior. For these widely used materials, the results suggest that light processing is a first necessary step before OPV characteristics can be meaningfully rated.