Addressing Triboelectric Nanogenerator Impedance for Efficient CO2 Utilization

Reducing the impedance of a triboelectric nanogenerator (TENG) without power loss is crucial for enhancing its energy conversion efficiency and overall performance. In this paper, a novel signal management structure, based on a newly designed sliding-mode TENG, aimed at effectively reducing impedance by converting narrow, instantaneous signals into broader ones is presented. This transformation is accomplished by adding a grounded electrode connected to a high-inductive inductor and fine-tuning the parasitic capacitance of the dielectric material. Utilizing a highly resistive material like P(VDF–TrFE), a significant improvement in the TENG's performance is achieved, resulting in an increase of output power to 0.352 mW and a decrease in impedance from 3.2 to 0.3 MΩ. This results in a threefold increase in charging speed, which can be attributed to the reduced charge loss and improved matching at lower impedance. Based on these promising findings, the enhanced TENG is successfully connected to power a system for electrochemical CO₂ reduction for CO production. This system effectively reduces the required electrochemical reduction potential by ≈15% under real environments.     

Synthesis of High Aspect Ratio BaTiO3 Nanowires for High Energy Density Nanocomposite Capacitors

High energy density capacitors are critically important in advanced electronic devices and power systems since they can reduce the weight, size and cost required to meet a desired application. Nanocomposites hold strong potential for increasing the performance of high power energy sources; however, the energy density of most nanocomposites is still low compared to commercial capacitors and neat polymers. Here, we develop a new synthesis method for the growth of high aspect ratio barium titanate nanowires (BaTiO₃) nanowires (NWs) with high yield. High energy density nanocomposite capacitors are fabricated using surface‐functionalized high aspect ratio BaTiO₃ NWs in a poly(vinylidene fluoride‐trifluoroethylene‐chlorofluoroethylene) (P(VDF‐TrFE‐CFE)) matrix. At a 17.5% volume fraction, the nanocomposites show more than 45.3% increase in energy density above that of the pure P(VDF‐TrFE‐CFE) polymer (10.48 J/cc compared to 7.21 J/cc) at electric field 300 MV/m. This value is significant and exceeds those reported for the conventional polymer‐ceramic nanocomposites; it is also more than seven times larger than high performance commercial polypropylene capacitor (1.2 J/cc at 640 MV/m). In addition, our nanocomposite capacitor has a maximum power density as high as 1.2 MW/cc occurring only 1.52 μs after the start of discharge. The findings of this research could lead to enhanced interest in nanowires based nanocomposites due to their potential for achieving next generation energy storage devices.     

Sustainable Energy Source for Wearable Electronics Based on Multilayer Elastomeric Triboelectric Nanogenerators

Wearable electronics have attracted a wide range of attention with various functions due to the development of semiconductor industry and information technology. This work focuses on a triboelectric nanogenerator‐based self‐charging power system as a continuous energy source for wearable electronics. The triboelectric nanogenerator has a multilayer elastomeric structure with closely stacked arches as basic functional units. Owing to material and structural innovations, this triboelectric nanogenerator performs outstanding electric output with the maximum volume charge density ≈0.055 C m^?3 and practical properties for energy harvesting from body motions. Utilizing the triboelectric nanogenerator as outsole to harvest energy from walking or jogging, a pair of shoes is fabricated with the maximum equivalent charge current of each shoe being around 16.2 µA and specific fitness functions realized on each shoe separately without complex connections.     

High Permittivity CaCu3Ti4O12 Particle‐Induced Internal Polarization Amplification for High Performance Triboelectric Nanogenerators

Here, a composite material based on the butylated melamine formaldehyde (BMF) and high permittivity CaCu₃Ti₄O₁₂ (CCTO) particles as a triboelectric dielectric material for stable high output triboelectric nanogenerators (TENGs) is proposed. CCTO particles, which have the high permittivity of 7500, can potentially result in the formation of strong internal polarization into the dielectric material under the electric field from triboelectric charges. As a consequence, the charge induction on the bottom electrode is enhanced thereby increasing the triboelectric output performance. A rotation‐type freestanding mode TENG based on BMF–CCTO 1 wt% composite material demonstrates high performance power output of a root‐mean‐square voltage and current density with 268 V and 25.8 mA m^?2, respectively. The strategy of incorporating the high permittivity CCTO particles can be universally applied to any triboelectric polymer matrix in order to enhance the output performance of TENGs.     

Cylindrical Direct‐Current Triboelectric Nanogenerator with Constant Output Current

In this article, a cylindrical direct‐current triboelectric nanogenerator (DC‐TENG) that can generate an almost constant current output with a low crest factor by phase coupling is reported for the first time. Here, the influence of phases (P) and groups (G) on the DC‐TENG is investigated. Experiments show that the crest factor of current, significantly decreases as the phases increase, and the output performance significantly increases as the groups increase. One phase triboelectric power‐generating unit of the DC‐TENG with three‐phase and five‐group (3P5G) produces an open‐circuit voltage of 149.5 V, short‐circuit current 7.3 μA, and transferred charge of 56.7 nC at 600 rpm. The DC‐TENG can produce a coupling current of 21.6 μA and the average output power of 2.04 mW after each phase output is rectified and superimposed. Additionally, the crest factor of output current is reduced to 1.08, and the high‐performance characteristics of an almost constant direct‐current is achieved. The research is of considerable significance to the practical applications of TENGs in powering sensors of low consumption.     

Quantifying Energy Harvested from Contact‐Mode Hybrid Nanogenerators with Cascaded Piezoelectric and Triboelectric Units

This paper presents an investigation of novel contact‐mode hybrid nanogenerators comprising cascaded piezoelectric and triboelectric units. For the first time, a theoretical analysis of the contact‐mode hybrid generator is presented to describe the relationships among transfer charges, voltage, current, and average output power in terms of material properties, hybrid generator structural parameters, harvesting, and operational conditions. New hybrid generators with much enhanced piezoelectricity are fabricated via a simple, room‐temperature, cost‐effective route by using nonwoven fabrics made from electrospun Polyvinyledenedifluoride‐trifluoroethylene (PVDF‐TrFE)/Ag nanowire nanofibers and Polydimethylsiloxane (PDMS) composites with graphite nanoparticles. The results provide a powerful tool for synthesis and selection of materials, design and optimization of the configuration, and operation of such kind of hybrid generators as well as determination of the value of external capacitor.     

A Novel MXene/Ecoflex Nanocomposite-Coated Fabric as a Highly Negative and Stable Friction Layer for High-Output Triboelectric Nanogenerators

The triboelectric material properties and mechanical stability of the contact layer are vital to achieving durable triboelectric nanogenerators (TENGs) with high output performance. Herein, a novel MXene/Ecoflex nanocomposite is introduced as a promising triboelectric material because of its highly negative triboelectric properties and mechanical stability. The MXene/Ecoflex nanocomposite with a fabric-based waterproof TENG (FW-TENG) is fabricated and designed to universally harvest energy from various human motions as well as the natural environment (rain and wind). The fabricated FW-TENG delivers a maximum output peak power of 3.69 mW and a power density of 9.24 W m⁻², respectively, at a matching load resistance of 4.5 MΩ under a frequency of 4.5 Hz and a force of 8 N. Furthermore, the applicability of this device in various products is investigated. The FW-TENG can protect against a crash caused by rainy and humid weather. An FW-TENG-based self-powered smart active device that detects motion on a carpet is demonstrated and is equipped with sleep monitoring motion sensors. The FW-TENG not only has self-powered benefits and excellent mechanical amenability but is also exceptionally reliable and stable against water intrusion, which are important characteristics to realize next-generation wearable/portable technologies.     

A Fully Verified Theoretical Analysis of Contact‐Mode Triboelectric Nanogenerators as a Wearable Power Source

Harvesting mechanical energy from human activities by triboelectric nanogenerators (TENGs) is an effective approach for sustainable, maintenance‐free, and green power source for wireless, portable, and wearable electronics. A theoretical model for contact‐mode triboelectric nanogenerators based on the principles of charge conservation and zero loop‐voltage is illustrated. Explicit expressions for the output current, voltage, and power are presented for the TENGs with an external load of resistance. Experimental verification is conducted by using a laboratory‐fabricated contact‐mode TENG made from conducting fabric electrodes and polydimethylsiloxane/graphene oxide composite as the dielectric layer. Excellent agreements of the output voltage, current, and power are demonstrated between the theoretical and experimental results, without any adjustable parameters. The effects of the moving speed on output voltage, current, and power are illustrated in three cases, that is, the motion with constant speed, the sinusoidal motion cycles, and the real walking cycles by human subject. The fully verified theoretical model is a very powerful tool to guide the design of the device structure and selection of materials, and optimization of performance with respect to the application conditions of TENGs.     

Nature Driven Bio‐Piezoelectric/Triboelectric Nanogenerator as Next‐Generation Green Energy Harvester for Smart and Pollution Free Society

Electronics wastes (e‐wastes) are the major concern in the rapid expansion of smart/wearable/portable electronics in modern high‐tech society. Informal processing and enormous gathering of e‐wastes can lead to adverse human/animal health effects and environmental pollution worldwide. Currently, these issues are a big headache and require the scientific community to develop effective green energy harvesting technologies using biodegradable/biocompatible materials. Piezoelectric/triboelectric nanogenerators (PNGs/TNGs) are considered one of the most promising renewable green energy sources for the conversion of mechanical/biomechanical energies into electricity. However, organic/inorganic material based PNGs/TNGs are very much incompatible, and considered e‐wastes for their non‐biodegradability. This review covers potential uses of biodegradable/biocompatible materials which are wasted every day as nature driven material based bio‐nanogenerators with a particular focus on their applications in flexible PNGs/TNGs fabrication. Structural investigation and possible working principles are described first in order to outline the basic mechanism of bio‐inspired materials behind energy harvesting. Then, energy harvesting abilities and the mechanical sensing of bio‐inspired integrated flexible devices are discussed under various mechanical/biomechanical activities. Finally, their potential applications in various flexible, wearable, and portable electronic fields are demonstrated. These bio‐inspired energy harvesting devices can make huge changes in fields as diverse as portable electronics, in vitro/in vivo biomedical applications, and many more.     

Enhancing the Output Performance of Triboelectric Nanogenerator via Grating‐Electrode‐Enabled Surface Plasmon Excitation

The surface charge density and the output impedance of triboelectric nanogenerators (TENGs) are two critical factors for TENGs to speed up their commercialization, so it is important to explore unique methods to reduce the output impedance and increase the surface charge density. Here, an approach is demonstrated to effectively boost the output performance of TENG while reducing the output impedance of TENGs by utilizing grating‐electrode‐enabled surface plasmon excitation. A sustainable and enhanced output performance of about 40 µA (short‐circuit current) and 350 V (peak‐to‐peak voltage at a resistance of 10 MΩ) is produced via grating‐coupled surface plasmon resonance on the TENG with the aluminum grating electrode in the line density of 600 lines mm^?1, and it delivers a peak output power of 3.6 mW under a loading resistance of 1 MΩ, giving over 4.5‐fold enhancement in output power and a 75% reduction in the output impedance. Finally a self‐powered ultrasonic ranging system is utilized to verify the capability of the TENG in powering portable electrics.     

Suppressing Lithium Dendrite Growth via Sinusoidal Ripple Current Produced by Triboelectric Nanogenerators

Lithium metal as an ultimate anode material of future rechargeable batteries may furnish the highest energy density for its pairing cathode, although preventing the growth of lithium dendrites in liquid electrolytes is a major challenge. This work reports that stable lithium metal anodes can be achieved by charging with high‐frequency sinusoidal ripple current generated by rotating triboelectric nanogenerators (R‐TENGs). Compared with constant DC current charging, sinusoidal ripple current charging by R‐TENG improves the uniformity of lithium deposition during cycling test. Consequently, symmetric Li/Li cells exhibit lower overpotential and better cycling stability. In addition, full cells assembled with lithium metal anodes and LiFePO₄ cathodes show considerably improved capacity retention when charged by R‐TENG's sinusoidal ripple current (99.5%) compared to constant current (78.7%) after 200 cycles. The charging strategy device in this work provides a promising direction toward improving the cycle life of Li metal batteries. In addition, the combination of R‐TENGs with Li metal batteries offers an encouraging solution for achieving stable energy supply in self‐powered systems.     

Rotating‐Disk‐Based Direct‐Current Triboelectric Nanogenerator

An innovative design is reported of a direct‐current triboelectric nanogenerator (DC‐TENG) based on a rotating disk design for harvesting rotational mechanical energy. The DC‐TENG consists of two disks and two pairs of flexible electric brushes that are made of carbon fiber and contact two electrodes, respectively. During the rotation, two disks have distinct triboelectric polarities for a cyclic in‐plane charge separation between them and an alternating current is generated between the two electrodes. Because of the sliding contact and automatically switch between the electric brushes and the two electrodes, the current is reversed in the second half of the cycle and a direct current is generated. The role that the rotating speed and the segmentation number have is thoroughly investigated and shows that there is direct current enhancement not only at higher speed but also with more segments. The DC‐TENG has been demonstrated as a constant current source for directly and continuously driving electronic devices and/or charging an energy storage unit without a rectifier bridge. This work presents a novel DC‐TENG technology and opens up more potential applications for harvesting rotational mechanical energy and powering electronics.     

High‐Output Triboelectric Nanogenerator Based on Dual Inductive and Resonance Effects‐Controlled Highly Transparent Polyimide for Self‐Powered Sensor Network Systems

High‐output triboelectric nanogenerators (TENGs) are demonstrated based on polyimide (PI)‐based polymers by introducing functionalities (e.g., electron‐withdrawing and electron‐donating groups) into the backbone. The TENG based on 6FDA‐APS PI, possessing the most negative electrostatic potential and the low‐lying lowest unoccupied molecular orbital level, produces the highest effective charge density of about 860 µC m^?2 in practical working conditions with the ion injection process. This may be ascribed to the excellent charge‐retention characteristics as well as the enhanced charge transfer capability, which increases the output power by 7 times compared to the commercially available Kapton film‐based TENG. Finally, a 6FDA‐APS‐driven sensor network system is demonstrated, providing the identity of three gases (H₂, CO, and NO₂) by illuminating the light‐emitting diodes within several seconds.     

Direct‐Current Triboelectric Nanogenerator Realized by Air Breakdown Induced Ionized Air Channel

The air breakdown phenomenon is generally considered as a negative effect in previous research on triboelectric nanogenerators (TENGs), which is always accompanied by air ionization. Here, by utilizing the air breakdown induced ionized air channel, a direct‐current triboelectric nanogenerator (DC‐TENG) is designed for harvesting contact‐separation mechanical energy. During working process, the charges first transfer from bottom to top electrodes through an external circuit in contact state, then flow back via the ionized air channel created by air breakdown in the separation process. So a unidirectional flow of electrical charges can be observed in the external circuit. With repeating contact‐separation cycles, continuous pulsed DC output through the external circuit can be realized. This working mechanism was verified by real‐time electrode potential monitoring, photocurrent signal detection, and controllable discharging observation. The DC‐TENG can be used for directly and continuously charging an energy storage unit and/or driving electronic devices without using a bridge rectifier. Owing to its simplicity in structure, the mechanism is further applied to fabricate the first flexible DC‐TENG. This research provides a significant fundamental study for DC‐TENG technology and may expand its application in flexible electronics and flexible self‐charging power systems.     

High‐Performance Triboelectric Nanogenerators Based on Solid Polymer Electrolytes with Asymmetric Pairing of Ions

In general, various kinds of surface modifications are utilized to enhance the power output performance of triboelectric nanogenerators (TENGs), but they typically have limited stability. Here, a new strategy of adding electrolytes with asymmetric ion pairing to polymer friction layers of TENGs is introduced in order to enhance their triboelectric property. Indeed, Kelvin probe force microscopy (KPFM) measurements show that an addition of phosphoric acid (H₃PO₄ ), an electrolyte with more cations than anions, to polyvinyl alcohol (PVA) can make it one of the most negative triboelectric materials; whereas, an addition of calcium chloride (CaCl₂ ), an electrolyte with more anions than cations, to PVA can make it one of the most positive triboelectric materials. Furthermore, the TENGs based on such solid polymer electrolytes (SPEs) produce significantly higher power output than typical metal‐polymer TENGs. Due to these unique features, SPEs are a promising triboelectric material for realizing high‐performance TENGs for self‐powered small electronics.     

A Wireless Triboelectric Nanogenerator

A new “wireless” paradigm for harvesting mechanical energy via a 3D‐printed wireless triboelectric nanogenerator (W‐TENG) comprised of an ecofriendly graphene polylactic acid (gPLA) nanocomposite and Teflon is demonstrated. The W‐TENG generates very high output voltages >2 kV with a strong electric field that enables the wireless transmission of harvested energy over a distance of 3 m. The W‐TENG exhibited an instantaneous peak power up to 70 mW that could be wirelessly transmitted for storage into a capacitor obviating the need for hard‐wiring or additional circuitry. Furthermore, the use of W‐TENG for wireless and secure actuation of smart‐home applications such as smart tint windows, temperature sensors, liquid crystal displays, and security alarms either with a single or a specific user‐defined passcode of mechanical pulses (e.g., Fibonacci sequence) is demonstrated. The scalable additive manufacturing approach for gPLA‐based W‐TENGs, along with their high electrical output and unprecedented wireless applications, is poised for revolutionizing the present mechanical energy harvesting technologies.     

Microdischarge‐Based Direct Current Triboelectric Nanogenerator via Accumulation of Triboelectric Charge in Atmospheric Condition

Direct conversion of mechanical energy into direct current (DC) by triboelectric nanogenerators (TENGs) is one of the desired features in terms of energy conversion efficiency. Although promising applications have been reported using the triboelectric effect, effective DC generating TENGs must be developed for practical purposes. Here, it is reported that continuous DC generation within a TENG itself, without any circuitry, can be achieved by triggering air breakdown via triboelectrification. It is demonstrated that DC generation occurs in combination with i) charge accumulation to generate air breakdown, ii) incident discharge (microdischarge), and iii) conveyance of charges to make the device sustainable. 10.5 mA m^?2 of output current and 10.6 W m^?2 of output power at 33 MΩ load resistance are achieved. Compared to the best DC generating TENGs ever reported, the TENG in this present study generates about 20 times larger root‐mean square current density.     

Tribovoltaic Effect on Metal–Semiconductor Interface for Direct‐Current Low‐Impedance Triboelectric Nanogenerators

The triboelectric nanogenerator (TENG) is a new energy technology that is enabled by coupled contact electrification and electrostatic induction. The conventional TENGs are usually based on organic polymer insulator materials, which have the limitations and disadvantages of high impedance and alternating output current. Here, a tribovoltaic effect based metal–semiconductor direct‐current triboelectric nanogenerator (MSDC‐TENG) is reported. The tribovoltaic effect is facilitated by direct voltage and current by rubbing a metal/semiconductor on another semiconductor. The frictional energy released by the forming atomic bonds excites nonequilibrium carriers, which are directionally separated to form a current under the built‐in electric field. The continuous average open‐circuit voltage (10–20 mV), short‐circuit direct‐current output (10–20 µA), and low impedance characteristic (0.55–5 kΩ) of the MSDC‐TENG can be observed during relative sliding of the metal and silicon. The working parameters are systematically studied for electric output and impedance characteristics. The results reveal that faster velocity, larger pressure, and smaller area can improve the maximum power density. The internal resistance is mainly determined by the velocity and the electrical resistance of semiconductor. This work not only expands the material candidates of TENGs from organic polymers to semiconductors, but also demonstrates a tribovoltaic effect based electric energy conversion mechanism.     

Multilayered‐Electrode‐Based Triboelectric Nanogenerators with Managed Output Voltage and Multifold Enhanced Charge Transport

The open‐circuit voltage of a triboelectric nanogenerator (TENG) increases with the tribo‐charge density and the separated distance between two tribo‐surfaces, which can reach several thousand volts and is much higher than the working voltage required by most electrical devices and energy storage units. Therefore, improving the effective efficiency of TENGs requires reducing the output voltage and enhancing the transferred charges. Here, a multilayered‐electrode‐based TENG (ME‐TENG) is developed in which the output voltage can be managed by controlling the charge flow in a process of multiple (N) steps, which results in N times lower voltage but N times higher total charge transport. The ME‐TENG is demonstrated to work in various modes, including multichannel, single‐channel, and double‐tribo‐surface structures. The effects of insulator layer thickness and total layer number on the output voltage are simulated by the finite element method. The output voltage can be modulated from 14 to 102 V by changing the insulator layer number between two adjacent working electrodes, based on which the 8‐bit logic representations of the characters in the ACSII code table are demonstrated. The ME‐TENG provides a novel method to manage the output power and has potential applications in self‐powered sensors array and human–machine interfacing with logic communications.     

An Ultrathin Flexible Single‐Electrode Triboelectric‐Nanogenerator for Mechanical Energy Harvesting and Instantaneous Force Sensing

The trends in miniaturization of electronic devices give rise to the attention of energy harvesting technologies that gathers tiny wattages of power. Here this study demonstrates an ultrathin flexible single electrode triboelectric nanogenerator (S‐TENG) which not only could harvest mechanical energy from human movements and ambient sources, but also could sense instantaneous force without extra energy. The S‐TENG, which features an extremely simple structure, has an average output current of 78 μA, lightening up at least 70 LEDs (light‐emitting diode). Even tapped by bare finger, it exhibits an output current of 1 μA. The detection sensitivity for instantaneous force sensing is about 0.947 μA MPa^?1. Performances of the device are also systematically investigated under various motion types, press force, and triboelectric materials. The S‐TENG has great application prospects in sustainable wearable devices, sustainable medical devices, and smart wireless sensor networks owning to its thinness, light weight, energy harvesting, and sensing capacities.