Electrochemical Stability of Li10GeP2S12 and Li7La3Zr2O12 Solid Electrolytes

The electrochemical stability window of solid electrolyte is overestimated by the conventional experimental method using a Li/electrolyte/inert metal semiblocking electrode because of the limited contact area between solid electrolyte and inert metal. Since the battery is cycled in the overestimated stability window, the decomposition of the solid electrolyte at the interfaces occurs but has been ignored as a cause for high interfacial resistances in previous studies, limiting the performance improvement of the bulk‐type solid‐state battery despite the decades of research efforts. Thus, there is an urgent need to identify the intrinsic stability window of the solid electrolyte. The thermodynamic electrochemical stability window of solid electrolytes is calculated using first principles computation methods, and an experimental method is developed to measure the intrinsic electrochemical stability window of solid electrolytes using a Li/electrolyte/electrolyte‐carbon cell. The most promising solid electrolytes, Li₁₀GeP₂S₁₂ and cubic Li‐garnet Li₇La₃Zr₂O₁₂, are chosen as the model materials for sulfide and oxide solid electrolytes, respectively. The results provide valuable insights to address the most challenging problems of the interfacial stability and resistance in high‐performance solid‐state batteries.     

The growth conditions of cephalosporium eichhorniae for the conversion of starch substrates to protein

The protein synthesis by Cephalosporium eichhorniae on substrates containing starch was evaluated at different pH, moisture content, ammonium sulphate and potassium dihydrogen phosphate supplementation. The optimum pH level was about 4.2 and the moisture content 65%. The optimum level of supplementation of medium containing sweet potato substrate with (NH₄)₂SO₄ was smaller than that for cassava substrate (5.2 g/l < 6.7 g/l in submerged culture, and 4.0% < 5.2% in solid state fermentation). The total crude protein yields were about 7.6 g/l for submerged cultures and 12% DM for solid state fermentations.     

Perovskite Membranes with Vertically Aligned Microchannels for All‐Solid‐State Lithium Batteries

Perovskite‐type solid‐state electrolytes exhibit great potential for the development of all‐solid‐state lithium batteries due to their high Li‐ion conductivity (approaching 10^?3 S cm^?1), wide potential window, and excellent thermal/chemical stability. However, the large solid–solid interfacial resistance between perovskite electrolytes and electrode materials is still a great challenge that hinders the development of high‐performance all‐solid‐state lithium batteries. In this work, a perovskite‐type Li_0.34La_0.51TiO₃ (LLTO) membrane with vertically aligned microchannels is constructed by a phase‐inversion method. The 3D vertically aligned microchannel framework membrane enables more effective Li‐ion transport between the cathode and solid‐state electrolyte than a planar LLTO membrane. A significant decrease in the perovskite/cathode interfacial resistance, from 853 to 133 Ω cm², is observed. It is also demonstrated that full cells utilizing LLTO with vertically aligned microchannels as the electrolyte exhibit a high specific capacity and improved rate performance.     

An Air‐Stable and Dendrite‐Free Li Anode for Highly Stable All‐Solid‐State Sulfide‐Based Li Batteries

Li metal is a promising anode material for all‐solid‐state batteries, owing to its high specific capacity and low electrochemical potential. However, direct contact of Li metal with most solid‐state electrolytes induces severe side reactions that can lead to dendrite formation and short circuits. Moreover, Li metal is unstable when exposed to air, leading to stringent processing requirements. Herein, it is reported that the Li₃PS₄/Li interface in all‐solid‐state batteries can be stabilized by an air‐stable Li_xSiS_y protection layer that is formed in situ on the surface of Li metal through a solution‐based method. Highly stable Li cycling for over 2000 h in symmetrical cells and a lifetime of over 100 cycles can be achieved for an all‐solid‐state LiCoO₂/Li₃PS₄/Li cell. Synchrotron‐based high energy X‐ray photoelectron spectroscopy in‐depth analysis demonstrates the distribution of different components within the protection layer. The in situ formation of an electronically insulating Li_xSiS_y protection layer with highly ionic conductivity provides an effective way to prevent Li dendrite formation in high‐energy all‐solid‐state Li metal batteries.     

柚子皮黑曲霉的分离鉴定及产酶特性研究

对柚子皮上自然生长的黑曲霉进行分离鉴定,并探讨其产酶特性。以平板稀释法从柚子皮上分离出一株霉菌菌株,通过观察其形态特征和培养特征,对照《真菌鉴定手册》判定该菌株的种属;采用鉴定培养基法对其产酶特性进行分析。根据柚子皮的成分特性,以干柚子皮为主要原料,该菌为生产菌株,采用固态发酵法探究培养基的成分、柚子皮含量、培养基初始含水量及发酵时间4个因素对纤维素酶活力的影响。结果表明,该菌株为黑曲霉(Aspergillus nige),可产淀粉酶、蛋白酶、纤维素酶、果胶酶;固态发酵培养基中添加柚子皮12g,麸皮0.5 g和(NH_4)_2SO_40.5 g,培养基初始含水量保持在68.5 mL/100 g,培养时间控制在60 h左右时纤维素酶产量较高。     

Supramolecular assembly using helical peptides

We investigated supramolecular assemblies of various hydrophobic helical peptides. The assemblies were formed at the air/water interface or in aqueous medium. The hexadecapeptide, Boc-(Ala-Aib)₈-OMe (BA16M), was reported to take α-helical structure by X-ray analysis. Several derivatives were prepared, which have the repeating sequence of Ala-Aib, Lys(Z)-Aib or Leu-Aib, or have the terminal chemically modified. CD spectra of the peptides indicated helical conformation in ethanol solution. The surface pressure-area isotherms of the peptide monolayers showed an inflection at the surface area corresponding to the cross section along the helix axis, and the monolayers were collapsed by further compression. All the helical peptides oriented their helix axis parallel to the air/water interface on the basis of the results of transmission IR spectra and RAS of the monolayers transferred onto substrates.A small mound was observed in the isotherm of BA16M and other derivatives, which was ascribed to the phase transition from the liquid state to the solid state. One mol% of FITC-labeled peptide was mixed into the monolayers to visualize the phase separation of the solid and liquid states at the surface pressure of the coexisting region. Various shapes of the dark domain were observed at the top of the mound in the isotherms by fluorescence microscopy. The helical peptides formed two-dimensional crystals at the air/water interface when they were compressed to the solid state.An amino-terminated helical peptide, HA16B, was suspended in an aqueous medium by a sonication method and transparent dispersion was obtained. The dynamic light scattering measurement of the dispersion revealed the particle size of 75 nm with a narrow size distribution. The molecular assembly of the helical peptide in water was called “Peptosome”, because it takes a vesicular structure.     

Bright solid‐state luminescence of green‐red tunable CdTe@BaCO3 composite: Synthesis and properties

Realizing efficient solid‐state luminescence is of great important to expand quantum dots (QDs) application fields. This work reports the preparation of CdTe@BaCO₃ composite by a one‐pot precipitation method. Both steady‐state PL and PL decay characteristics in either solid‐state or colloid solution show no obvious difference, mainly benefited from the effective protection of BaCO₃ on QDs from the external environment. By utilizing green and red CdTe QDs as dual‐color emission centers, precise emitting‐color control from green (0.312, 0.667) to red (0.691, 0.292) could be achieved in CdTe@BaCO₃ composite by adjusting volume ratio of CdTe solution precursor. Our results demonstrate that this composite material shows bright solid‐state luminescence and facile adjustment of the emitting color in QDs‐based composite is feasible, which could offer new path to design color‐tunable luminescent materials for future optoelectronic applications.     

红色诺卡菌固体培养基配方的优化

应用响应面优化设计法优化固体培养基配方,增大红色诺卡菌的固体培养细胞生物量。首先用Plackett-Burman法从现有培养基组分中找到影响红色诺卡菌细胞生物量的关键因素,再通过最陡爬坡法确定细胞生物量最大的配方,用作中心组合设计(Central Composite Design, CCD)实验的基础起始值,拟合数学模型方程,最后找到最优组分的组合。优化的配方转移至企业实施放大实验,对结果进行验证和比较。试验结果表明,培养基各组分中影响红色诺卡菌细胞生物量的关键因素为蛋白胨、NaCl、牛肉膏;最优固体培养基配方:蛋白胨42 g/L、牛肉膏8 g/L、NaCl 1.2 g/L、甘油10 mL/L、Na_2HPO_4·12H_2O 0.3 g/L、琼脂20 g/L。在细胞生物量方面最优固体培养基配方比原配方高104%。响应面优化设计可用于提高红色诺卡菌细胞生物量固体培养基的优化,也为红色诺卡菌培养条件、液体发酵的优化研究提供参考。     

Biomass estimation of Aspergillus niger growing on real and model supports in solid state fermentation

Summary Direct hydrolysis of Aspergillus niger mycelium growth on amberlite IRA-900 or sugar cane bagasse on solid state fermentation followed by the analysis of soluble protein by the dye binding method was carried out. Hydrolysis with phosphoric acid 0.25M during 7 min allowed maxima protein extraction available to be measured. Color interference of medium components was not observed, allowing the use of this method for biomass estimation when amberlite IRA-900 or sugar cane bagasse are used as support in solid state fermentation processes.     

Production of ligninolytic exoenzymes and14C-Pyrene mineralization byPleurotus sp. in lignocellulose substrate

Pleurotus sp. was grown in liquid medium and on a solid straw substrate, and activities of laccase and manganese-dependent peroxidase (MnP) were recorded. The activities were the highest in a rich, glucose corn-steep liquid medium. In straw cultures, laccase activity was about ten times lower. Under solid state conditions, MnP production was the highest during days 20–40, when laccase activity already had declined. In straw cultures, mineralization of¹⁴C-pyrene was measured as release of¹⁴CO₂. The highest rates of pyrene mineralization occurred during days 20–45,i.e. the period of high MnP activities, suggesting a role of this enzyme in PAH degradation. Within 60d, 24% of pyrene was mineralized.     

Insights into the discrepant luminescence for BaSiO3:Eu2+ phosphors prepared by solid‐state reaction and precipitation reaction methods

Two synthesis routes, solid‐state reaction and precipitation reaction, were employed to prepare BaSiO₃:Eu²⁺ phosphors in this study. Discrepancies in the luminescence green emission at 505 nm for the solid‐state reaction method sample and in the yellow emission at 570 nm for the sample prepared by the precipitation reaction method, were observed respectively. A detail investigation about the discrepant luminescence of BaSiO₃:Eu²⁺ phosphors was performed by evaluation of X‐ray diffraction (XRD), photoluminescence (PL)/photoluminescence excitation (PLE), decay time and thermal quenching properties. The results showed that the yellow emission was generated from the BaSiO₃:Eu²⁺ phosphor, while the green emission was ascribed to a small amount of Ba₂SiO₄:Eu²⁺ compound that was present in the solid‐state reaction sample. This work clarifies the luminescence properties of Eu²⁺ ions in BaSiO₃ and Ba₂SiO₄ hosts.     

Control of carbon dioxide in exhaust air as a method for equal biomass yields at different bed heights in a column fermentor

Summary The rate of aeration of the medium in a solid state fermentation system for biomass production by Schwanniomyces castellii in a large column fermentor was found to influence the gradient of biomass yield at different bed heights. The variations were lower with a higher rate of aeration. These trends were used to formulate a successful strategy to ensure equal biomass yield at all the bed heights by controlling the level of CO₂ at about 2% in exhaust air from the fermentor. Correspondence to: B. K. Lonsane     

Leucojum aestivum L. in vitro bulbs induction and acclimatization

The effects of growth retardants (paclobutrazol and ancymidol), sucrose, GA₃ (gibberellic acid) and physical state of the medium (solid and liquid — Rita® temporary immersion system) on in vitro induction of Leucojum aestivum bulbs and their acclimatization were studied. Paclobutrazol, regardless of the physical state of the medium, stimulated the formation of bulbs (99.3%). Under the influence 90 g L^?1 of sucrose or paclobutrazol the bulbs with the highest fresh weight (FW) were formed (250 mg and 208.8 mg, respectively). However, the addition of ancymidol to the liquid medium led to obtaining the bulbs showing the highest number of leaves and roots (63.2% and 91.7%, respectively). The scanning microscopy study proved that plants obtained in the medium containing GA₃ produced the stomata which most closely resembled to the one observed in the mother plant. Cytometric analysis of all regenerants revealed absence of changes in the nuclear DNA content. The maximum survival rate (100%) was observed for plants derived from liquid medium containing 90 g L^?1 of sucrose. Somewhat fewer plants were acclimatized after their cultivations in liquid medium enriched with paclobutrazol or ancymidol. The temporary immersion system led to perform successful ex vitro adaptation of Leucojum aestivum plants.     

Improvements to the Overpotential of All‐Solid‐State Lithium‐Ion Batteries during the Past Ten Years

After the research that shows that Li₁₀GeP₂S₁₂ (LGPS)‐type sulfide solid electrolytes can reach the high ionic conductivity at the room temperature, sulfide solid electrolytes have been intensively developed with regard to ionic conductivity and mechanical properties. As a result, an increasing volume of research has been conducted to employ all‐solid‐state lithium batteries in electric automobiles within the next five years. To achieve this goal, it is important to review the research over the past decade, and understand the requirements for future research necessary to realize the practical applications of all‐solid‐state lithium batteries. To date, research on all‐solid‐state lithium batteries has focused on achieving overpotential properties similar to those of conventional liquid‐lithium‐ion batteries by increasing the ionic conductivity of the solid electrolytes. However, the increase in the ionic conductivity should be accompanied by improvements of the electronic conductivity within the electrode to enable practical applications. This essay provides a critical overview of the recent progress and future research directions of the all‐solid‐state lithium batteries for practical applications.     

Photoluminescence property of A9B(VO4)7 [A = Ca,Sr, Ba and B = La,Gd] phosphors

A new efficient phosphor, A₉B(VO₄)₇ [A = Ca, Sr, Ba and B = La, Gd] has been synthesized by the solid‐state method at high temperature. X‐ray diffraction analysis confirmed the formation of the compound. Photoluminescence excitation measurements show that the phosphor can be efficiently excited by near‐ultraviolet light from 300 nm to 400 nm to realize emission covering the 397–647 nm region of visible spectrum. Therefore, newly synthesized novel phosphor may be useful as green‐emitting phosphor in solid‐state lighting. Copyright © 2012 John Wiley & Sons, Ltd.     

Improvement of Aconitum napellus micropropagation by liquid culture on floating membrane rafts

An efficient method was developed using floating membrane rafts (Liferaft) for the micropropagation of Aconitum napellus (Ranunculaceae), a cut flower crop with a low natural propagation rate. This was achieved by introducing shoot tips into culture on Murashige and Skoog's (1962) solid medium, or liquid medium-supported rafts, supplemented by different levels of benzyl adenine (BA). Optimum shoot proliferation on solid medium required 4mg/l BA, whereas for expiants supported on rafts optimal proliferation was achieved at 0.25mg/l BA. Maximum shoot proliferation was found using the floating rafts (propagation ratio of 4.2 per month), 45% higher than the maximum value on solid medium. A similar value could be obtained on solid medium after a period of 2 months. The optimal response to BA was similar for fresh weight gain and shoot length. Growth in a shallow layer of liquid in shake flasks gives a similar shoot multiplication rate to that on floating rafts; however, submerged leaves brown and die.Abbreviations BA 6-benzylaminopurine - GA₃ Gibberellic acid - IBA indole-3-butyric acid - IAA indole-3-acetic acid - NAA naphthalene acetic acid     

Method for Detection of Microorganisms That Produce Gaseous Nitrogen Oxides

A method was developed to detect NO- or N₂O-producing bacteria in solid or liquid medium by their ability to oxidize the redox indicator resazurin from its reduced colorless form to its oxidized pink form. The method was sensitive to as little as 35 nM N₂O or 0.5 nM NO. Ninety-one percent of the colonies that oxidized resazurin on plates also produced N₂O in slant cultures. Forty-four percent of the colonies that did not oxidize resazurin did produce N₂O. This percentage was reduced to 15% when colonies in which the coloration was difficult to discern were picked to slants to determine whether they oxidized the slant. The production of N₂O preceded the oxidation of resazurin by liquid cultures of Escherichia coli and a sludge isolate. With the denitrifying sewage isolate, the disappearance of N₂O was followed by the return of resazurin to its reduced state. Wolinella succinogenes was found to produce small amounts of N₂O from NO₃⁻, which resulted in a transient oxidation of resazurin.     

Biosynthesis of protein by microscopic fungi in solid state fermentation. II. Optimization of aspergillus oryzae A. or. 11 cultivation for protein enrichment of starchy raw materials

Study was made of the effect of medium humidity, source and dose of nitrogen, dose of phosphorus, dose of inoculum and aeration on protein biosynthesis by strain Aspergillus oryzae A. or. 11 in solid state fermentation. It was found that for a maximal protein yield the medium ought to contain about: 60% of water, 36% of starchy raw materials d. m. (e.g. 28.8% of coarse rye meal and 7.2% of beet pulp), 0.85% of nitrogen sources (1.6% of (NH₄)₂SO₄ and 1.1% of urea), and 0.35% of phosphorus source (1.3% of KH₂PO₄). pH of medium should be near 6.5. The dose of inoculum should not be lower than 10⁸ spores/100 g medium. The duration of culture ought to be 20–22 h at 30–35°C, with aeration at least 40 dm³ of air/h × 1000 g medium. Under these conditions the protein yield is about 6.0–6.3 g/100 g of starting medium d.m. at the cost of utilization of about 25 g total carbohydrates.     

Physically Stable Polymer‐Membrane Electrolytes for Highly Efficient Solid‐State Dye‐Sensitized Solar Cells with Long‐Term Stability

A 3D polymer‐network‐membrane (3D‐PNM) electrolyte is described for highly stable, solid‐state dye‐sensitized solar cells (DSCs) with excellent power‐conversion efficiency (PCE). The 3D‐PNM electrolyte is prepared by using one‐pot in situ cross‐linking polymerization on the surface of dye‐sensitized TiO₂ particles in the presence of redox species. This method allows the direct connection of the 3D‐PNM to the surface of the TiO₂ particles as well as the in situ preparation of the electrolyte gel during device assembly. There are two junction areas (liquid and solid‐state junctions) in the DSCs that employ conventional polymer electrolytes, and the major interface is at the liquid‐state junction. The solid‐state junction is dominant in the DSCs that employ the 3D‐PNM electrolyte, which exhibit almost constant performance during aging at 65 °C for over 700 h (17.0 to 17.2 mA cm^–2). The best cell performance gives a PCE of 9.1%; this is slightly better than the performance of a DSC that employs a liquid electrolyte.     

Ameliorating the Interfacial Problems of Cathode and Solid‐State Electrolytes by Interface Modification of Functional Polymers

Solid‐state Li secondary batteries may become high energy density storage devices for the next generation of electric vehicles, depending on the compatibility of electrode materials and suitable solid electrolytes. Specifically, it is a great challenge to obtain a stable interface between these solid electrolytes and cathodes. Herein, this issue can be effectively addressed by constructing a poly(acrylonitrile‐co‐butadiene) coated layer onto the surface of LiNi_0.6Mn_0.2Co_0.2O₂ cathode materials. The polymer layer plays a vital role in working as a protective shell to retard side reaction and ameliorate the contact of the solid–solid interface during the cycling process. In the resultant solid‐state batteries, both rate capacity (99 mA h g^?1 at 3 C) and cycling stability (75% capacity retention after 400 cycles) are improved after coating. This impressive performance highlights the great importance of layer modification in the cathode and inspires the development of solid‐state batteries toward practical applications.