Synthesis of N-Octyl Oleate with Lipase from Mucor miehei Immobilized onto Polyethylene Based Graft Copolymers

Lpase from Mucor miehei was immobilized onto partially hydrolyzed poly(ethylene)-g.co-hydroxyethyl methacrylate (PE/HEMA) via spacer arms of 1,6-diaminohexane and glutaraldehyde-. The PE/HEMA-lipase system was used for the enzymatic esterification of n-octanol with oleic acid in the absence of organic solvents. The influence of lipase' concentration, in the attachment solution, on the ester production profile and initial reaction rate was studied. It was found that very small amounts of lipase gave preparations which reached good degrees of conversion. The effect of the initial oleic acid concentration on that pseudo-first order reaction, as well as the presence of water in the reactional medium and the influence of temperature were evaluated. It was found that initial oleic acid concentrations lesser than 1.2 M did not inhibit the immobilized lipase activity; the presence of small amount of water (10–30μ) solubilized in the reaction mixture (6.5 cm³) increased the lipase activity and a maximum of activity of the immobilized lipase preparation was found at 55d`C. The operational stability of the preparation was determined at 37d`C in a BSTR type reactor and a half-life time of three days for the immobilized lipase was obtained.     

Variables that Affect Immobilization of Mucor Miehei Lipase on Nylon Membrane

Nylon membrane was used to immobilize Mucor miehei lipase. Variables that affect this immobilization procedure were studied by experimental design. A 2³ full factorial design was employed for this purpose. The protein retention and hydrolytic activity of the immobilized lipase were used as response variables. The rapid loss of enzyme activity was the main problem during repetitive use. Two strategies were used to improve the low operational stability: nylon treated with HCl and nylon coated with polyvinyl alcohol (PVA). Lipase-nylon-PVA was the best enzyme derivative, allowing performance of five consecutive assays, with a retained activity of 0.5 U mg of protein⁻¹ g of support⁻¹.     

Poly(Ethylene Oxide), a New Slowing Agent for Protozoa

SYNOPSIS The water-soluble, viscoelastic resin Polyox® (WSR 301), a poly(ethylene oxide) of high molecular weight (4 million) is introduced as a new slowing agent for protozoa. Generally, as the kinetic viscosity of the resin increased from 0.25% to 1% (w/v), the swimming velocity of Euglena gracilis, Didinium nasutum, Paramecium aurelia, Blepharisma undulans , and Prorodon platyodon decreased. The 1.0% solution had the highest viscosity and decreased velocity more effectively than 1.0% methyl cellulose and Protoslo® solutions. The Polyox solutions differed from those of methyl cellulose and Protoslo by having, in addition to viscous drag, an elastic recoil that pulled the protozoa backwards when their swimming efforts stopped. The toxicity of these slowing agents was determined using 10 P. aurelia /test slide preparation. Paramecium numbers decreased in 1.0% methyl cellulose and Protoslo to nearly zero by 24 hr; in Polyox, not only were most of these ciliates alive after 24 hr, but many survived for 96 hr and divisions occurred in 0.25% and 0.50% solutions.     

Immobilization of Candida rugosa lipase on colloidal gas aphrons (CGAs)

A novel technique for immobilization of Candida rugosa lipase onto anionic colloidal gas aphrons (CGAs) is described. CGAs are spherical microbubbles (10-100 microm) composed of an inner gas core surrounded by a surfactant shell. In this initial study, greater than 80% lipase (w/w) was effectively retained on the CGAs. Leakage of protein from the CGAs and the activity of the adsorbed lipase decreased with increasing enzyme loading; this indicates that multilayers of lipase may be adsorbing onto the CGAs. The CGA-immobilised lipase displayed normal Michaelis-Menten dependence on substrate concentration and also exhibited greater activity than the free enzyme.     

Immobilization of hog pancreas lipase in macroporous poly(vinyl alcohol)-cryogel carrier for the biocatalysis in water-poor media

Hog pancreas lipase was covalently attached to the beads of poly(vinyl alcohol)-cryogel – a macroporous hydrogel prepared by means of freeze-thaw technique. The immobilized biocatalyst thus obtained was examined in the reaction of enantioselective hydrolysis of the ethyl ester of N-benzylidene derivative of DL-phehylalanine in the medium of acetonitrile (contained 5 vol.% of water without any buffers). Eighty-three %-enantiomeric excess of the l-amino acid was reached after 144 h. Virtually the same result was obtained in the repeated use of the same immobilized biocatalyst after its 6-months-storing in a refrigerator.     

Immobilization of glucoamylase from Aspergillus niger on poly(ethylenimine)-coated non-porous glass beads

Glucoamylase (1,4-α-d-glucan glucohydrolase, EC 3.2.1.3) from A. niger was immobilized on cationic nonporous glass beads (13–44 μm) by electrostatic adsorption followed by rosslinking with glutaraldehyde. Over 80% of the enzyme's total soluble activity was expressed upon immobilization. d-Glucose production from maltodextrins was virtually complete, suggesting that the lack of pores can eliminate the problem of product reversion. Immobilized glucoamylase showed decreased stability upon heating, compared with the soluble enzyme.     

The Roles of Poly(Ethylene Oxide) Electrode Buffers in Efficient Polymer Photovoltaics

The role of poly(ethylene oxide) polymer is investigated as an effective buffer with Al electrodes to markedly improve the electrode interface and enhance the open‐circuit voltage (V_OC) and the power conversion efficiency (PCE, η) of poly(3‐hexylthiophene) (P3HT):[6,6]‐phenyl C61‐butyric acid methyl ester (PCBM)‐based bulk‐heterojunction (BHJ) solar cells. A unique process is developed by thermally co‐evaporating the poly(ethylene glycol) dimethyl ether (PEGDE, Mn ca. 2000) polymer with Al metal simultaneously at different ratios in vacuum (10^?6 Torr) to prepare the electrode buffers. The instant formation of a carbide‐like junction at the ethylene oxide/Al interface during the thermal evaporation is of essential importance to the extraction of electrons through the Al electrode. The performance of P3HT:PCBM‐based solar cells can be optimized by modulating the co‐evaporation ratios of the PEGDE polymer with Al metal due to the changes in the work functions of the electrodes. The V_OC and η for devices fabricated with Al electrode are 0.44 V and 1.64%, respectively, and significantly improve to 0.58 V and 4.00% when applying the PEGDE:Al(2:1)/Al electrode. This research leads to a novel electrode design – free of salts, additives, complicated syntheses, and having tunable work function – for fabricating high‐performance photovoltaic cells.     

Effect of Solvents and Kinetic Parameters on Synthesis of Ethyl Propionate Catalysed by Poly (AAc-co-HPMA-cl-MBAm)-Matrix-Immobilized Lipase of Pseudomonas aeruginosa BTS-2.

Summary A purified alkaline thermo-tolerant bacterial lipase from Pseudomonas aeruginosa BTS-2 was immobilized on a poly (AAc-co-HPMA-cl-MBAm) hydrogel network. The hydrogel showed approximately 95% binding efficiency for lipase (specific activity 1.96 U mg⁻¹). The immobilized enzyme achieved 65.1% conversion of ethanol and propionic acid (100 mM each) into ethyl propionate in n-nonane at 65 °C in 9 h. When alkane of C-chain length lower than n-nonane was used as the organic solvent, the conversion of ethanol and propionic acid into ethyl propionate decreased with a decrease in the log P value of alkanes. The immobilized lipase retained approximately 30% of its original catalytic activity after five cycles of reuse for esterification of ethanol and propionic acid into ethyl propionate at temperature 65 °C in 3 h. Addition of a molecular sieve (3 ?) to the reaction mixture enhanced the formation of ethyl propionate to 89.3%. Moreover, ethanol and propionic acid when taken a molar ratio of 3:1 further promoted the conversion rate to 94%. However, an increase in the molar ratio of propionic acid with respect to ethanol resulted in a decline of ethyl propionate synthesis.     

Poly(ethylene glycol) quantitation by laser nephelometry

When poly(ethylene glycol) 3350 is estimated by the method of Skoog [(1979) Vox Sang. 37, 345-349], fine particles form. The particles are not attributable to residual protein but to a poly(ethylene glycol)/barium/iodine complex that can be quantitated by means of a laser nephelometer. The method is sensitive to at least 10 mg% poly(ethylene glycol) 3350 (4 micrograms in the cuvette) in 2500 mg% protein, and nephelometer response is approximately linear between 30 and 200 mg% of the polymer. The coefficient of variance is about 8%. Triton X-100, Pluronic F-68, Varonic 1000MS, and poly(ethylene glycol) of higher and lower molecular weight react well. Alkylated celluloses, dextrans, glycerol, glycine, and sodium dodecyl sulfate do not react significantly. Barium can be replaced with Mg, Ca, Ni, Fe, and other divalent cations in the reaction, but other than for Hg, light-scattering is most intense with Ba. The reaction goes to completion in about 5 min and is most intense when the barium is added before the iodine.     

评论：塑料结合模块促进聚对苯二甲酸乙二醇酯的酶法降解

塑料的大量生产和无节制的使用已造成严重的环境污染。为了减少塑料废物对环境的影响,近年来塑料酶法降解已成为国内外研究者关注的热点。例如,通过蛋白质工程策略提高塑料降解酶催化活性和热稳定性,进一步提高酶法降解的效率。另外,通过融合酶策略将塑料结合模块与塑料降解酶融合,也可以促进塑料降解。近期发表在期刊Chem Catalysis的一项研究表明,采用碳水化合物结合模块融合策略可以在低浓度(<10 wt%)的底物聚对苯二甲酸乙二醇酯[poly(ethylene terephthalate),PET]中提高塑料降解酶的活性。但是在高浓度底物(10 wt%−20 wt%)中,该策略无法提高PET的酶法降解。该项研究对于采用塑料结合模块促进酶法降解塑料具有重要的指导意义。     

重组大肠杆菌合成聚(3-巯基丙酸)和聚(3-羟基丁酸-3-巯基丙酸)的研究

利用Clostridium acetobutylicum的丁酸激酶基因 (buk) 和磷酸转丁酰基酶基因(ptb),以及Thiocapsa pfennigii的PHA合成酶基因,设计了一条能够合成多种聚羟基烷酸的代谢途径,用构建的质粒转化大肠杆菌,获得了重组大肠杆菌菌株.前期的研究表明,在合适的前体物条件下,该重组大肠杆菌能够合成包括聚羟基丁酸、聚(羟基丁酸-戊酸)等多种生物聚酯[Liu and Steinbüchel, Appl. Environ. Microbiol. 66739-743].利用该重组大肠杆菌,通过生物催化作用合成了3-巯基丙酸的同型共聚酯,同时利用该重组大肠杆菌还获得了含3-巯基丙酸单体的多种异型共聚物.实验首先研究了3-巯基丙酸对大肠杆菌生长的影响,在此基础上优化了培养过程中添加3-巯基丙酸的时机和浓度,结果表明,在实验的条件下,细胞合成聚(3-巯基丙酸)可达6.7%(占细胞干重),合成聚(3-羟基丁酸-3-巯基丙酸)(分子中3-巯基丙酸3-羟基丁酸=31)可达24.3%.实验进一步研究了同时或分别表达以上3个基因的重组大肠杆菌合成聚合物的能力,结果表明只有当3个基因同时表达时才能合成聚合物,说明3个基因对合成过程是必须的,从而表明了合成途径是按照设计的路线进行的.还通过GC/MS、GPC、IR等手段对合成的化合物进行了定性的研究.聚(3-巯基丙酸)或聚(3-羟基丁酸-3-巯基丙酸)等聚酯属于一类新型生物聚合物,它在分子骨架中含有硫酯键,不同于聚羟基烷酸酯的氧酯键,从而具有显著不同的物理、化学、光学等性质和具有重要的潜在应用价值.     

多ADP-核糖聚合酶家族

分离鉴定多功能的核基质蛋白及核基质结合蛋白是目前核基质研究的一个重要领域。通过与转录因子、核基质结合元件以及DNA间相互作用,核基质结合蛋白在DNA复制、转录、加工修饰等细胞内事件中起着支持和调节的作用。多ADP-核糖聚合酶[poly(ADP—ribose)polymerase,PARP]是一种高度保守的核基质结合蛋白,在多种活动例如基因组损伤修复、细胞凋亡、信号转导、基因表达调控中都发挥着调节的功能。PARP的潜在生物学功能已越来越引起国内外研究人员的关注。     

Studies on the activity and stability of immobilized horseradish peroxidase on poly(ethylene terephthalate) grafted acrylamide fiber

Having been activated with glutaraldehyde, modified poly(ethylene terephthalate) grafted acrylamide fiber was used for the immobilization of horseradish peroxidase (HRP). Both the free HRP and the immobilized HRP were characterized by determining the activity profile as a function of pH, temperature, thermal stability, effect of organic solvent and storage stability. The optimum pH values of the enzyme activity were found as 8 and 7 for the free HRP and the immobilized HRP respectively. The temperature profile of the free HRP and the immobilized HRP revealed a similar behaviour, although the immobilized HRP exhibited higher relative activity in the range from 50 to 60 °C. The immobilized HRP showed higher storage stability than the free HRP.     

Resolution of N-(2-ethyl-6-methylphenyl) alanine catalyzed by Lipase B from Candida antarctica

A biotransformation process has been developed for the production of (S)-N-(2-ethyl-6-methylphenyl) alanine by enantioselective hydrolysis of racemic methyl ester in the presence of Candida antarctica lipase B (CAL-B). However, the enantioselectivity of CAL-B towards the resolution is not high enough to obtain enantiomerically pure product. In order to improve the enantioselectivity of the enzyme, the effects of surfactants on CAL-B-catalyzed hydrolysis were tested. The results suggest that surfactants can influence the microenvironment of the enzyme, and the addition of Tween-80, in particular, to the reaction medium markedly enhanced the selectivity of CAL-B towards the substrate used, with the enantiomeric ratio (E-value) increasing from 11.3 to 60.1.     

Resolution of N-(2-ethyl-6-methylphenyl) alanine catalyzed by Lipase B from Candida antarctica

A biotransformation process has been developed for the production of (S)-N-(2-ethyl-6-methylphenyl) alanine by enantioselective hydrolysis of racemic methyl ester in the presence of Candida antarctica lipase B (CAL-B). However, the enantioselectivity of CAL-B towards the resolution is not high enough to obtain enantiomerically pure product. In order to improve the enantioselectivity of the enzyme, the effects of surfactants on CAL-B-catalyzed hydrolysis were tested. The results suggest that surfactants can influence the microenvironment of the enzyme, and the addition of Tween-80, in particular, to the reaction medium markedly enhanced the selectivity of CAL-B towards the substrate used, with the enantiomeric ratio (E-value) increasing from 11.3 to 60.1.     

聚腺苷酸特异性核糖核酸酶(PARN)的功能多样性

聚腺苷酸尾的降解对于mRNA的质量控制和转录后基因调控十分重要. 在真核生物中,去腺苷酸化是mRNA降解和翻译沉默的首要限速步骤. 3′核糖核酸外切酶--聚腺苷酸特异性核糖核酸酶（poly(A)-specific ribonuclease,PARN）能够高效降解真核生物mRNA的聚腺苷酸尾. PARN不仅在降解mRNA poly(A)尾中发挥关键的作用,还参与DNA损伤、非编码RNA的加工成熟以及肿瘤等疾病过程. PARN是一种多功能酶分子,本文就PARN发现、结构、催化机制和功能多样性进行综述.