Modified Laminar Flow Biological Safety Cabinet

Tests are reported on a modified laminar flow biological safety cabinet in which the return air plenum that conducts air from the work area to the high efficiency particulate air filters is under negative pressure. Freon gas released inside the cabinet could not be detected outside by a freon gas detection method capable of detecting 10(-6) cc/s. When T3 bacteriophage was aerosolized 5 cm outside the front opening in 11 tests, no phage could be detected inside the cabinet with the motor-filter unit in operation. An average of 2.8 x 10(5) plaque-forming units (PFU)/ft(3) (ca. 0.028 m(3)) were detected with the motor-filter unit not in operation, a penetration of 0.0%. Aerosolization 5 cm inside the cabinet yielded an average of 10 PFU/ft(3) outside the cabinet with the motor-filter unit in operation and an average of 4.1 x 10(5) PFU/ft(3) with the motor-filter unit not in operation, a penetration of 0.002%. These values are the same order of effectiveness as the positive-pressure laminar flow biological safety cabinets previously tested. The advantages of the negative-pressure return plenum design include: (i) assurance that if cracks or leaks develop in the plenum it will not lead to discharge of contaminated air into the laboratory; and (ii) the price is lower due to reduced manufacturing costs.     

Microbiological Studies on the Performance of a Laminar Airflow Biological Cabinet

Engineering and microbiological tests indicated that a typical, commercial laminar airflow cabinet was not effective in providing either product protection or agent containment. The cabinet was modified and tested through a series of alternate configurations to establish a set of design criteria. A mock-up cabinet was developed from these design criteria. The mock-up unit was evaluated for efficiency in providing both product protection and agent containment. In these evaluations, challenge methods were developed to simulate normal, in-use laboratory operations. Controlled bacterial or viral aerosol challenges were used at higher than normal levels to provide stringent test conditions. Test results indicated that the mock-up unit was considerably better in preventing agent penetration (0.1 to 0.2 particles per 100 ft(3) of air) than the commercial cabinet (5 to 6 particles per 100 ft(3) of air) during product protection tests. Similarly, agent containment was considerably better in the new cabinet (particle escape of 2 to 3 per 100 ft(3) of air at only one of the five test sites) than in the commercial cabinet (particle escape of 2 to 14 per 100 ft(3) of air at three of the five test sites).     

Microbiological Evaluation of a Large-Volume Air Incinerator

Two semiportable metal air incinerators, each with a capacity of 1,000 to 2,200 standard ft(3) of air per min, were constructed to sterilize infectious aerosols created for investigative work in a microbiological laboratory. Each unit has about the same air-handling capacity as a conventional air incinerator with a brick stack but costs only about one-third as much. The units are unique in that the burner housing and combustion chamber are air-tight and utilize a portion of the contaminated air stream to support combustion of fuel oil. Operation is continuous. Aerosols of liquid and dry suspensions of Bacillus subtilis var. niger spores and dry vegetative cells of Serratia marcescens were disseminated into the two incinerators to determine the conditions required for sterilization of contaminated air. With the latter organisms (concentration 2.03 x 10(7) cells/ft(3) of air), a temperature of 525 F (274 C), measured at the firebox in front of the heat exchanger, was sufficient for sterilization. To sterilize 1.74 x 10(7) and 1.74 x 10(9) wet spores of B. subtilis per ft(3), the required temperature ranged from 525 to 675 F (274 to 357 C) and 625 to 700 F (329 to 371 C), respectively. Air-sterilization temperature varied with each incinerator. This was because of innate differences of fabrication, different spore concentrations, and use of one or two burners With dry B. subtilis spores (1.86 x 10(8)/ft(3)), a temperature of 700 F was required for sterilization. With dry spores, no difference was noted in the sterilization temperature for the two incinerators.     

Containment of Microbial Aerosols in a Microbiological Safety Cabinet

A microbiological safety cabinet was evaluated to determine conditions under which microorganisms might escape. Tests were conducted under three cabinet-closure conditions, various airflow velocities, and different laboratory operations, with 10(5), 1.1 x 10(5), and 10(6) microorganisms per cubic foot of cabinet space released per min for 5 min. The data revealed that (i) escape of a human infectious dose is possible when the cabinet is used with the glove panel off; (ii) the number of organisms that escaped from the cabinet increased with a decrease in air velocity; and (iii) an increase in the number of laboratory operations resulted in an increase in the number of organisms that escaped. Thus, when the glove panel was off, the cabinet was only safe for operations that released a small number of microorganisms into the cabinet, whereas the cabinet was safe for operations of significantly greater hazard when used with the glove panel on but with the gloves unattached.     

Production of Bacteriophage by Temperature-Sensitive Sporulation Mutants of Bacillus cereus T

Five temperature-sensitive sporulation mutants of Bacillus cereus T have been isolated. These mutants are blocked at stage 0 of sporulation at the restrictive temperature (37 C) but are able to sporulate at nearly normal frequencies at the permissive temperature (26 C). A bacteriophage that forms a stable lysogen in the parent strain is induced at increased frequencies in the mutants. This induction is accompanied, in some of the mutants, by a reduction in immunity to the phage. Revertants, selected for their ability to sporulate normally at both temperatures, lose their ability to produce high titers of the phage. In addition to this lytic phage, an apparently defective phage has been found in lysates of the mutants. Strains cured of the plaque-forming phage still carry the defective phage. Comparisons of physical and biological properties of the plaque-forming phage with those of the two Bacillus cereus phages most similar to it have shown that this phage is not identical to either of them. The maximal titer of phage produced in cultures of the parent strain is about 10(3) plaque-forming units (PFU) per ml at both temperatures. The maximal titers of phage produced by the mutant are 4 x 10(9) PFU/ml at 37 C and 7 x 10(8) PFU/ml at 26 C. Both mutant and parent strains release over 90% of the phage they produce after the onset of stationary phase.     

Comparison of different bioreactor systems for the production of high titer retroviral vectors

Improved, human-based packaging cell lines allow the production of high-titer, RCR-free retroviral vectors. The utility of these cell lines for the production of clinical grade vectors critically depends on the definition of optimal conditions for scaled-up cultures. In this work, a clone derived from the TE Fly GALV packaging cell (Duisit et al. Hum. Gene Ther. 1999, 10, 189) that produces high titers of a lacZ containing retroviral vector with a Gibbon Ape Leukemia Virus envelope glycoprotein was used. This clone can produce (2-5) x 10(6) PFU cm(-3) in small scale cultures and has been evaluated for growth and vector production in different reactor systems. The performances of fixed bed reactors [CellCube (Costar) and Celligen (New Brunswick)] and stirred tank reactors [microcarriers and clump cultures] were compared. The cells showed a higher apparent growth rate in the fixed bed reactor systems than in the suspension systems, probably as a result of the fact that aggregation and/or formation of clumps led to a reduced viability and reduced growth of cells in the interior of the clumps. As a consequence, the final cell density and number were in average 3- to 7-fold higher in the fixed bed systems in comparison to the suspension culture systems. The average titers obtained ranged from 0.5 to 2.1 x 10(7) PFU cm(-3) for the fixed bed and microcarrier systems, while the clump cultures produced only (2-5) x 10(5) PFU cm(-3). The differences in titers reflect cell densities as well as specific viral vector production rates, with the immobilization and microcarrier systems exhibiting an at least 10-fold higher production rate in comparison to the clump cultures. A partial optimization of the culture conditions in the Celligen fixed bed reactor, consisting of a 9-fold reduction of the seeding cell density, led to a 5-fold increased vector production rate accompanied by an average titer of 3 x 10(7) PFU cm(-3) (maximum titer (4-5) x 10(7) PFU cm(-3)) in the fixed bed reactor. The performance evaluation results using mathematical models indicated that the fixed bed bioreactor has a higher potential for retroviral vector production because of both the higher reactor productivity and the lower sensitivity of productivity in relation to the changes in final retrovirus titer in the range of 3 x 10(6) to 15 x 10(6) PFU cm(-3).     

Transduction of concatemeric plasmids containing the cos site of Lactococcus lactis bacteriophage sk1

Lactococcus lactis bacteriophage sk1 can transduce plasmids containing the phage cos site and surrounding DNA sequences at frequencies as high as 2x10(-3) transductants per PFU. Deletion analysis demonstrated that the presence of phage DNA spanning cos and putative R sites were the most important for efficient plasmid transduction. Inserts of 440 bp containing cos and the R sites were sufficient to induce transduction frequencies of 10(-4) transductants per PFU. The role of the R1 site was investigated by altering 14 of the 19 bases in the site. This resulted in a two-fold decrease in transduction frequency compared to a 26-fold decrease in transduction following deletion of the entire site. It was demonstrated that transducing plasmids were packaged as linear trimeric concatemers commencing at the cos site.     

小鼠呼肠孤病毒Ⅲ型标准化血清制备及ELISA检测方法的建立

目的制备标准化小鼠呼肠孤病毒III型（reovirus 3,Reo-3）免疫血清,建立小鼠Reo-3抗体ELISA检测方法。方法使用动物来源的Reo-3病毒感染BALB/c小鼠,获得高效价免疫血清;以BHK-21细胞制备Reo-3病毒抗原,同时制备做正常对照抗原。滴定抗原和标准化小鼠Reo-3血清的最佳工作浓度,进行特异性、敏感性、重复性、稳定性等实验。结果制备18 mL抗Reo-3血清,经检测,IFA效价达1∶640,IEA效价达1∶160;Reo-3抗原和标准化小鼠Reo-3免疫血清最佳工作浓度分别为5μg/mL和1∶2400;该ELISA检测体系Reo-3特异抗原批内变异系数为3.8%,批间变异系数为4.0%;检测灵敏度〉1∶4400;与仙台病毒（SV）、小鼠肝炎病毒（MHV）、小鼠腺病毒（Mad）、小鼠脑脊髓炎病毒（TMEV）、小鼠多瘤病毒（POLY）均无交叉反应。经37℃破坏性试验,2 d稳定性试验相对偏差〈27%。结论本研究制备的Reo-3抗血清达到同批次大量高滴度的水平,可作为检测实验小鼠Reo-3病原的标准化质控血清。本研究建立的ELISA方法重复性、稳定性好,特异性、敏感性强。该体系可用于大、小鼠等实验动物Reo-3抗体的检测。     

Buoyant Density Analysis of Staphylococcal Bacteriophage 80 Transducing Particles

Densities of pase, tet, and ol transducing particles were indistinguishable, and about 0.002 g x cm(-3) less dense than the plaque-forming units (PFU). The densities of the PFU and nov transducing particles were indistinguishable, the PFU having a density of 1.507 g x cm(-3).     

Effects of housing density and cage floor space on three strains of young adult inbred mice

Some recommendations in the Guide for the Care and Use of Laboratory Animals (the Guide) are based on best professional judgment. Our current efforts are directed toward replacement with data-driven standards. We demonstrated earlier that young adult C57BL/6J mice could be housed with half the floor space recommended in the Guide without discernable negative effects. This report extends that work by examining optimal housing densities for young adult male and female BALB/cJ, NOD/LtJ, and FVB/NJ mice. These 8-week studies were initiated with 3-week-old BALB/cJ and NOD/LtJ mice and 3- to 5-week-old FVB/NJ mice housed in three cage types. We adjusted the number of mice per cage to house them with the floor space recommended in the Guide (approximately 12 in2 [ca. 77 cm2] per mouse) down to 5.6 in2 [ca. 36 cm2] per mouse. Early-onset aggression occurred among FVB/NJ male mice housed at all densities in cages having 51.7 in2 (ca. 333 cm2) or 112.9 in2 (ca. 728 cm2) of space. FVB/NJ male mice housed in shoebox (67.6 in2 [ca. 436 cm2]) cages did not exhibit aggression until the fifth week. Urinary testosterone output was density-dependent only for BALB/cJ male mice in shoebox cages (output decreased with increasing density) and FVB/NJ male mice. We conclude that all but FVB/NJ male mice can be housed with half the floor space specified in the Guide. The aggression noted for male FVB/NJ mice may have been due to their age span, although this did not impact negatively on the female FVB/NJ mice.     

Sources of Campylobacter spp. colonizing housed broiler flocks during rearing

The study aimed to identify sources of campylobacter in 10 housed broiler flocks from three United Kingdom poultry companies. Samples from (i) the breeder flocks, which supplied the broilers, (ii) cleaned and disinfected houses prior to chick placement, (iii) the chickens, and (iv) the environments inside and outside the broiler houses during rearing were examined. Samples were collected at frequent intervals and examined for Campylobacter spp. Characterization of the isolates using multilocus sequence typing (MLST), serotyping, phage typing, and flaA restriction fragment length polymorphism typing was performed. Seven flocks became colonized during the growing period. Campylobacter spp. were detected in the environment surrounding the broiler house, prior to as well as during flock colonization, for six of these flocks. On two occasions, isolates detected in a puddle just prior to the birds being placed were indistinguishable from those colonizing the birds. Once flocks were colonized, indistinguishable strains of campylobacter were found in the feed and water and in the air of the broiler house. Campylobacter spp. were also detected in the air up to 30 m downstream of the broiler house, which raises the issue of the role of airborne transmission in the spread of campylobacter. At any time during rearing, broiler flocks were colonized by only one or two types determined by MLST but these changed, with some strains superseding others. In conclusion, the study provided strong evidence for the environment as a source of campylobacters colonizing housed broiler flocks. It also demonstrated colonization by successive campylobacter types determined by MLST during the life of a flock.     

Aerosols containing Legionella pneumophila generated by shower heads and hot-water faucets

Shower heads and hot-water faucets containing Legionella pneumophila were evaluated for aerosolization of the organism with a multistage cascade impaction air sampler. Air was collected above two shower doors and from the same rooms approximately 3 ft (91 cm) from the shower doors while the hot water was running. Low numbers (3 to 5 CFU/15 ft3 [0.43 m3] of air) of L. pneumophila were recovered above both shower doors, but none was recovered from the air in either room outside the shower door. Approximately 90% (7 of 8 CFU) of the L. pneumophila recovered were trapped in aerosol particles between 1 and 5 micron in diameter. Air was collected 1 to 3 ft (30 to 91 cm) from 14 sinks while the hot water was running. Low numbers (1 to 5 CFU/15 ft3 of air) were recovered from 6 of 19 air samples obtained. Approximately 50% (6 of 13 CFU) of the organisms recovered were trapped in aerosol particles between 1 and 8 microns in diameter. Shower heads and hot-water taps containing L. pneumophila can aerosolize low numbers of the organism during routine use. The aerosol particle size is small enough to penetrate to the lower human respiratory system. Thus, these sites may be implicated as a means of transmission of L. pneumophila from potable water to the patient.     

Aerosols containing Legionella pneumophila generated by shower heads and hot-water faucets.

Shower heads and hot-water faucets containing Legionella pneumophila were evaluated for aerosolization of the organism with a multistage cascade impaction air sampler. Air was collected above two shower doors and from the same rooms approximately 3 ft (91 cm) from the shower doors while the hot water was running. Low numbers (3 to 5 CFU/15 ft3 [0.43 m3] of air) of L. pneumophila were recovered above both shower doors, but none was recovered from the air in either room outside the shower door. Approximately 90% (7 of 8 CFU) of the L. pneumophila recovered were trapped in aerosol particles between 1 and 5 micron in diameter. Air was collected 1 to 3 ft (30 to 91 cm) from 14 sinks while the hot water was running. Low numbers (1 to 5 CFU/15 ft3 of air) were recovered from 6 of 19 air samples obtained. Approximately 50% (6 of 13 CFU) of the organisms recovered were trapped in aerosol particles between 1 and 8 microns in diameter. Shower heads and hot-water taps containing L. pneumophila can aerosolize low numbers of the organism during routine use. The aerosol particle size is small enough to penetrate to the lower human respiratory system. Thus, these sites may be implicated as a means of transmission of L. pneumophila from potable water to the patient.     

Evaluation of a forced-air-ventilated micro-isolation system for protection of mice against Pasteurella pneumotropica.

Studies to date have established that the physical environment inside cages can be controlled adequately by setting the intra-cage ventilation at 60 air changes per hour in a forced-air-ventilated micro-isolation system (FVMIS). In this study, the capability of FVMIS to prevent inter-cage transmission of microorganisms was evaluated using Pasteurella pneumotropica as a reference microorganism. One FVMIS rack and a conventional rack were used, and cages with mice positive for P. pneumotropica and those with P. pneumotropica-free mice were housed on both racks. The mice were examined for P. pneumotropica contamination every 4 weeks after initiating the experiment for 12 weeks using a polymerase chain reaction method. Some P. pneumotropica-free mice housed in open air cages in the conventional rack became positive for P. pneumotropica (four of 28 animals after 4 weeks; eight of 28 animals after 12 weeks), but all P. pneumotropica-free mice housed in the FVMIS cages remained negative for the bacterium throughout the experiment. The results demonstrate that FVMIS can prevent inter-cage transmission of P. pneumotropica when proper cage handling practice is under taken.     

Sources of Campylobacter spp. Colonizing Housed Broiler Flocks during Rearing

The study aimed to identify sources of campylobacter in 10 housed broiler flocks from three United Kingdom poultry companies. Samples from (i) the breeder flocks, which supplied the broilers, (ii) cleaned and disinfected houses prior to chick placement, (iii) the chickens, and (iv) the environments inside and outside the broiler houses during rearing were examined. Samples were collected at frequent intervals and examined for Campylobacter spp. Characterization of the isolates using multilocus sequence typing (MLST), serotyping, phage typing, and flaA restriction fragment length polymorphism typing was performed. Seven flocks became colonized during the growing period. Campylobacter spp. were detected in the environment surrounding the broiler house, prior to as well as during flock colonization, for six of these flocks. On two occasions, isolates detected in a puddle just prior to the birds being placed were indistinguishable from those colonizing the birds. Once flocks were colonized, indistinguishable strains of campylobacter were found in the feed and water and in the air of the broiler house. Campylobacter spp. were also detected in the air up to 30 m downstream of the broiler house, which raises the issue of the role of airborne transmission in the spread of campylobacter. At any time during rearing, broiler flocks were colonized by only one or two types determined by MLST but these changed, with some strains superseding others. In conclusion, the study provided strong evidence for the environment as a source of campylobacters colonizing housed broiler flocks. It also demonstrated colonization by successive campylobacter types determined by MLST during the life of a flock.     

Attenuated, replication-competent herpes simplex virus type 1 mutant G207: safety evaluation in mice

Herpes simplex virus type 1 (HSV-1) mutants that are attenuated for neurovirulence are being used for the treatment of cancer. We have examined the safety of G207, a multimutated replication-competent HSV-1 vector, in mice. BALB/c mice inoculated intracerebrally or intracerebroventricularly with 10(7) PFU of G207 survived for over 20 weeks with no apparent symptoms of disease. In contrast, over 80% of animals inoculated intracerebrally with 1.5 x 10(3) PFU of HSV-1 wild-type strain KOS and 50% of animals inoculated intracerebroventricularly with 10(4) PFU of wild-type strain F died within 10 days. Similarly, after intrahepatic inoculation of G207 (3 x 10(7) PFU) all animals survived for over 10 weeks, whereas no animals survived for even 1 week after inoculation with 10(6) PFU of KOS. After intracerebroventricular inoculation, LacZ expression was initially observed in the cells lining the ventricles and subarachnoid space; expression decreased until almost absent within 5 days postinfection, with no apparent loss of ependymal cells. G207 DNA could be detected by PCR in the brains of mice 8 weeks after intracerebral inoculation; however, no infectious virus could be detected after 2 days. As a model for latent HSV in the brain, we used survivors of an intracerebral inoculation of HSV-1 KOS at the 50% lethal dose. Inoculation of a high dose of G207 at the same stereotactic coordinates did not result in reactivation of detectable infectious virus or symptoms of disease. We conclude that G207 is safe at or above doses that were efficacious in mouse tumor studies.     

Characterization of Inducible Bacteriophages in Bacillus licheniformis

Two morphologically distinct and physically separable defective phages have been found in Bacillus licheniformis NRS 243 after induction by mitomycin C. One of them (PBLB) is similar to the defective phage PBSX of B. subtilis, which has a density of 1.373 g/cm(3) in CsCl and a sedimentation coefficient of 160S. PBLB incorporates into its head mainly bacterial deoxyribonucleic acid (DNA) which has a sedimentation coefficient of 22S and a buoyant density in CsCl of 1.706 g/cm(3). The other phage (PBLA) has a morphology similar to the temperate phage phi105 of B. subtilis; the head diameter is about 66 nm, and it possesses a long and noncontractile tail. PBLA has a density of 1.484 g/cm(3) in CsCl and the phage-specific DNA, which is exclusively synthesized after induction by mitomycin C, has a density of 1.701 g/cm(3). PBLA DNA is double-stranded and has a sedimentation coefficient of 36S, corresponding to a molecular weight of 34 x 10(6) to 35 x 10(6) daltons. The phage DNA has one interruption per single strand, giving single-stranded segments with molecular weights of 13 x 10(6) and 4 x 10(6) daltons. Common sequences between the two phage DNA species and with their host DNA have been demonstrated by DNA-DNA hybridization studies. Both phage particles kill sensitive bacteria. However, all attempts thus far to find an indicator strain to support plaque formation have been unsuccessful.     

Airborne Detection and Quantification of Swine Influenza A Virus in Air Samples Collected Inside,Outside and Downwind from Swine Barns

Airborne transmission of influenza A virus (IAV) in swine is speculated to be an important route of virus dissemination, but data are scarce. This study attempted to detect and quantify airborne IAV by virus isolation and RRT-PCR in air samples collected under field conditions. This was accomplished by collecting air samples from four acutely infected pig farms and locating air samplers inside the barns, at the external exhaust fans and downwind from the farms at distances up to 2.1 km. IAV was detected in air samples collected in 3 out of 4 farms included in the study. Isolation of IAV was possible from air samples collected inside the barn at two of the farms and in one farm from the exhausted air. Between 13% and 100% of samples collected inside the barns tested RRT-PCR positive with an average viral load of 3.20E+05 IAV RNA copies/m³ of air. Percentage of exhaust positive air samples also ranged between 13% and 100% with an average viral load of 1.79E+04 RNA copies/m³ of air. Influenza virus RNA was detected in air samples collected between 1.5 and 2.1 Km away from the farms with viral levels significantly lower at 4.65E+03 RNA copies/m³. H1N1, H1N2 and H3N2 subtypes were detected in the air samples and the hemagglutinin gene sequences identified in the swine samples matched those in aerosols providing evidence that the viruses detected in the aerosols originated from the pigs in the farms under study. Overall our results indicate that pigs can be a source of IAV infectious aerosols and that these aerosols can be exhausted from pig barns and be transported downwind. The results from this study provide evidence of the risk of aerosol transmission in pigs under field conditions.