Self-cycling fermentation in a stirred tank reactor

Self-cycling fermentations (SCFs) were conducted in a stirred tank apparatus using Bacillus subtilis and Acinetobacter calcoaceticus. The systems were very stable and the experiments lasted through many cycles. The variation of parameters such as biomass and doubling time from cycle to cycle was small. The stirred tank reactor (STR) allowed a much better control of the working volume in the fermentor from cycle to cycle, compared to the cyclone column, and it was not necessary to make periodic corrections.The production of surfactin from B. subtilis was achieved without extending the cycle time. The harvested broth at the end of each cycle was allowed to remain in a secondary vessel, at ambient temperature, before being collected. It is exhaustion of the limiting nutrient which causes an increase in dissolved oxygen (DO). At this point, the computer, which constantly monitors the DO, triggered the harvesting sequence to end the cycle. Thus, the mature culture in the secondary vessel experienced appropriate conditions for the production of the secondary metabolite. Meanwhile, the next batch of cells was being grown in the primary reactor.The response of a gas analyzer on the effluent paralleled that of the DO measurements in the fermentor. These data for oxygen and carbon dioxide exhibited less noise than the DO readings. Either would be a more reliable parameter for feedback control of the SCF because the problem of fouling of the DO probe after extended runs of many cycles would be eliminated. (c) 1993 John Wiley & Sons, Inc.     

Semi-continuous xylose-to-xylitol bioconversion by Ca-alginate entrapped yeast cells in a stirred tank reactor

Candida guilliermondii FTI 20037 cells were entrapped in Ca-alginate beads and used for xylose-to-xylitol bioconversions during five successive batches in a stirred tank reactor. Supplemented sugarcane bagasse hemicellulosic hydrolysate was used as the fermentation medium. The average volume of the Ca-alginate beads was reduced by about 30% after the 600 h taken to perform the five bioconversion cycles, thus demonstrating physical instability under the conditions prevailing in the reactor vessel. In spite of this, almost steady bioconversion rates and yields were observed along the repeated batches. In average values, a production of 51.6 g l(-1), a productivity of 0.43 g l(-1 )h(-1) and a yield of 0.71 g g(-1) were attained in each batch, variation coefficients being smaller than 10%.     

Cephalosporin C production in a stirred tank reactor

Summary Cephalosporin C was produced with the moldCephalosporium acremonium in a 20 1 stirred tank reactor with 100 kg/m³ peanut flour in fed-batch operation. The growth and product formation was followed by on-line analysis of the broth composition. The cell concentration was estimated from the RNA-content of the cells. By optimization of the fed-batch operation and by increasing the phosphate content in the broth, a final cephalosporin C concentration of 12 kg/m³ was attained.Nomenclature CPC cephalosphorin C - DAC deacetylcephalosporin C - DAOC deacetoxycephalosporin C - k _L a volumetric mass transfer coefficient - MMBS 2-Hydroxy-4-methylmercaptobutyric acid - PABAH p-Hydroxybenzoicacidhydrazid - RNA ribonucleic acid - RQ respiratory quotient - oxygen transfer rate - CO₂-production rate - t fermentation time     

Continuous ATP production by spinach thylakoid in a stirred tank reactor

Spinach thylakoid was immobilized by two different methods for the purpose of retention within a continuous-flow stirred tank reactor (CSTR). The glutaraldehyde crosslinked albumin polymer method completely inactivated the cyclic ATP photophosphorylation of thylakoid. In contrast, agarose-entrapped thylakoid retained about 17% of the activity of the cyclic photophosphorylation of non-immobilized thylakoid. This activity declined continuously during ATP production in the CSTR. Fifty percent of the initial activity was lost within about 5.5 h. Ascorbate was found to increase the stability of ATP photophosphorylation; about twice as much ATP was produced at the optimal ascorbate concentration of 5 mM. Under the optimal dilution rate of 2.36 h⁻¹, about 60 μmol of ATP per mg chlorophyll were produced in 20 h by agarose-entrapped thylakoid in the CSTR. These results showed that, compared to non-immobilized thylakoid in batch operation, agarose-entrapped thylakoid produced only a low amount of ATP under continuous operation.     

Phosphorus removal in aerated stirred tank reactor

The possibility to obtain biological phosphorus removal in strictly aerobic conditions has been investigated. Experiments, carried out in a continuous stirred tank reactor (CSTR), show the feasibility to obtain phosphorus removal without the anaerobic phase. Reactor performance in terms of phosphorus abatement kept always higher then 65% depending on adopted sludge retention time (SRT). In fact increasing SRT from 5 days to 8 days phosphorus removal and reactor performance increase but overcoming this SRT value a decreasing in reactor efficiency was recorded.     

Production and purification of human menin from Drosophila melanogaster S2 cells using stirred tank reactor

A process was developed for producing human menin from transformed Drosophila Schneider 2 cells. Protein expression was achieved after inducing the metallothionein promoter by adding copper sulfate to cells growing in suspension in a stirred-tank reactor. Experiments in shake flasks showed that the production of menin was improved when the induction was conducted late in the exponential phase of cell growth at a concentration of 1–2 × 10⁷ cells ml^-1, with a copper concentration of 0.2 mM for no more than 24 h. This observation was confirmed by experiments in bench-scale fermentors. Subsequently, a pilot-scale fermentation yielded 1 mg l^-1 culture of purified menin. This revised version was published online in July 2006 with corrections to the Cover Date.     

Production of ethanol by a stirred catalytic basket reactor with immobilized yeast cells

A stirred catalytic basket reactor with immobilized yeast cells was used for the batchwise production of ethanol. Fractional conversions up to 0.99 in 10 h were attained, depending on the agitation rates, initial glucose, and cell densities. The volumetric productivity of the reactor was considerably better than that of conventional stirred tank reactors. Productivities were strongly dependent on the stirred speed.     

Production of alkaline serine protease subtilisin Carlsberg by Bacillus licheniformis on complex medium in a stirred tank reactor

Bacillus licheniformis (DSM 641) was cultivated on complex medium in batch and fed-batch operations in a 20-l working volume stirred tank reactor. The medium composition (maltose, glucose, sucrose, fructose, ammonia, phosphate) and O₂ and CO₂ in the off-gas were monitored on-line; pH, pO₂, turbidity, culture fluorescence were monitored in situ; optical density, concentrations of sugars, amino acids, phosphate, proteins, DNA, protease activity and total solids content were monitored off-line. Problems of on-line sampling, cell concentration monitoring, and culture fluorescence measurements and the influence of medium components on the enzyme productivity are discussed. Close relationships between variations of pH, pO₂, O₂ transfer rate and CO₂ production rate on the one hand and cell mass and fluorescence intensity on the other were demonstrated in batch and in fed-batch cultures. Using suitable cultivation conditions, alkaline protease with high volume activity [15300 units (U)/ml] and specific activity (510 U/mg) was produced. By replacing the complex medium with a semisynthetic one, the volumetric activity was reduced by a factor of ten (to 1650 U/ml), but the specific productivity by a factor of only two (to 210 U/ml). Correspondence to: K. Schügerl     

Bioleaching of chalcopyrite concentrate by a moderately thermophilic culture in a stirred tank reactor

A mixed culture of moderately thermophilic microorganisms was enriched from acid mine drainage samples collected from several chalcopyrite mines in China. Such mixed culture can be used to effectively extract copper from chalcopyrite. Furthermore, after being adapted to gradually increased concentration of chalcopyrite concentrate, the tolerance of the mixed culture to chalcopyrite concentrate was brought up to 80 g/L. The effects of several leaching parameters on copper recovery in stirred tank reactor also had been investigated. The results of the investigation show that it was possible to achieve a copper extraction rate of 75% in 44 days at a pulp density of 8%. The leaching rate of chalcopyrite concentrate tended to increase with dissolved total iron concentration. At low pH ranges, more microscopic counts of microorganisms were found in the solution. Furthermore, the analysis of leached residues indicates that the passivation of chalcopyrite concentrate was mainly due to a mass of jarosite and PbSO(4) on the mineral surface, other than the elemental sulphur layer. The bacterial community composition was analyzed by using Amplified Ribosomal DNA Restriction Analysis. Two moderately thermophilic bacteria species were identified as Leptospirillum ferriphilum and Acidithiobacillus caldus with abundance of 67% and 33% in the bio-pulp, respectively.     

Production of the biocontrol agent Pantoea agglomerans PBC-1 in a stirred tank reactor by batch and fed-batch cultures

Concerns about food safety as well as the development of resistance to many fungicides by major postharvest pathogens have increased recently. Biological control, using microorganisms antagonistic to the fungal plant pathogens, appears to be promising as an alternative to fungicides. The microbial biocontrol agent has to be produced on an industrial scale, maintaining its biocontrol efficacy. The purpose of the current study was to optimize the conditions for microbial biomass production of the biocontrol agent Pantoea agglomerans PBC-1 in a 2-l mechanically stirred reactor (STR), defining mixing and mass transfer technological parameters and the growth kinetics for different saccharides. In the batch mode, different impellers and spargers were tested. Despite the oxygen mass transfer improvement achieved with marine propeller combined with porous sparger, the biomass did not increase, if compared with the use of a Rushton turbine and L-sparger, pointing out the relevance of a radial flux for better broth homogenization. Different carbon sources were used: sucrose, glucose and fructose; each of which led to viable populations 3.9 × 10⁹, 1.4 × 10⁹, 3.9 × 10⁹ c.f.u/ml, respectively, after 20 h of incubation. Fed-batch technology allows the maintenance of high cell viability for longer periods of time in the stationary growth phase, which can be crucial for the scale-up of biocontrol agent production process that is achieved together with a reduction of 85% on the incidence caused by the pathogens, brought about by fresh microbial biomass preparation on artificially wounded apples or oranges, stored for 7 days at 25°C against Penicillium expansum and Penicillium digitatum.     

Production of recombinant human interleukin-2 with BHK cells in a hollow fibre and a stirred tank reactor with protein-free medium.

For the production of recombinant human interleukin-2 (IL-2) two different culture processes, a 1-2 liter homogeneous stirred bubble-free aerated system and a dense cell hollow fibre bioreactor were compared. Cultivations were carried out with serum- or protein-free medium formulations. In the stirred culture 0.75 mg IL-2 were produced with 1 l of perfused medium at a maximum cell number of 3 X 10(10). The product yield in the hollow fibre module was only 0.23 mg l-1 at a maximum cell number of 6 X 10(10). In contrast to results with hybridoma or EBV-transformed cell lines, in which hollow fibre bioreactors showed comparable efficiency to perfused stirred tank reactors, the tissue-like cell density is disadvantageous as adherent cells tend to stick together leaving insufficient intercellular space for removal of product.     

Hydrogen metabolic patterns driven by Clostridium-Streptococcus community shifts in a continuous stirred tank reactor

Applied Microbiology and Biotechnology - The hydrogen (H2) production efficiency in dark fermentation systems is strongly dependent on the occurrence of metabolic pathways derived from the...     

Production of a novel polygalacturonic acid bioflocculant REA-11 by Corynebacterium glutamicum

The production of a novel polygalacturonic acid bioflocculant REA-11 from a newly isolated strain, Corynebacterium glutamicum CCTCC M201005, was investigated. Sucrose was chosen as a carbon source for REA-11 production. Complex nitrogen sources containing urea and an organic nitrogen compound enhanced both bacterial growth and REA-11 production, among which urea plus corn steep liquor was shown to be the most efficient combination. A cost-effective medium for REA-11 production mainly comprised 17 g/l sucrose, 0.45 g/l urea, and 5 ml/l corn steep liquor, under which conditions the flocculating activity reached 390 U/ml. The molar ratio of carbon to nitrogen (C/N) significantly affected REA-11 production, where a C/N ratio of 20:1 was shown to be the best. Interestingly, by simultaneously feeding sucrose and urea at a C/N ratio of 20:1 at 24 h of fermentation, REA-11 production (458 U/ml) was enhanced by 17% compared to the control. In a 10 l jar fermentor, lower dissolved oxygen tension was favorable for REA-11 production: a flocculating activity of 520 U/ml was achieved at a kappaLa of 100 h(-1). REA-11 raw product is relatively thermo-stable at acidic pH ranges of 3.0-6.5. Preliminary application studies showed that REA-11 had stronger flocculating activity to Kaolin clay suspension compared to chemical flocculants. In addition, the capability of decolorizing molasses wastewater indicates the industrial potential of this novel bioflocculant.     

Study of microencapsulated urease in a continuous feed,stirred tank reactor

Urease, (urea amidohydrolase, EC 3.5.1.5) co-encapsulated with haemoglobin in cellulose nitrate membranes was found to exhibit apparent Michaelis-Menten kinetics; however, a steadily increasing apparent Michaelis-Menten constant over the lifetime of the preparation was observed. The activity of the enzyme in a continuous feed stirred tank reactor (CSTR) was investigated and correlated with a mathematical model derived from basic Michaelis-Menten kinetics. Plots relating substrate conversion to feed substrate concentration and tank reactor capacity were constructed and found to be accurate to less than 15% error under the experimental conditions studied.     

Production of organic acids by Corynebacterium glutamicum under oxygen deprivation

Under oxygen deprivation, aerobic Corynebacterium glutamicum produce organic acids from glucose at high yields in mineral medium even though their proliferation is arrested. To develop a new, high-productivity bioprocess based on these unique features, characteristics of organic acid production by C. glutamicum under oxygen deprivation were investigated. The main organic acids produced from glucose under these conditions were lactic acid and succinic acid. Addition of bicarbonate, which is a co-substrate for anaplerotic enzymes, increased the glucose consumption rate, leading to increased organic acid production rates. With increasing concentration of bicarbonate, the yield of succinic acid increased, whereas that of lactic acid decreased. There was a direct correlation between cell concentration and organic acid production rates even at elevated cell densities, and productivities of lactic acid and succinic acid were 42.9 g l⁻¹ h⁻¹ and 11.7 g l⁻¹ h⁻¹, respectively, at a cell concentration of 60 g dry cell l⁻¹. This cell-recycling continuous reaction demonstrated that rates of organic acid production by C. glutamicum could be maintained for at least 360 h.     

Bacterial monitoring by molecular tools of a continuous stirred tank reactor treating textile wastewater

This study was performed to examine the effect of the bacterial diversity changes on the performances of a continuously stirred tank reactor (CSTR) treating textile wastewater. The molecular fingerprint established using polymerase chain reaction-single stranded conformation polymorphism (PCR-SSCP) methods showed that bacterial community profiles changed simultaneously with the increase of the wastewater loading rates (WLR). For the two WLR of 0.28 g l(-1)d(-1) and 0.37 g l(-1)d(-1), the reactor maintained good performances, suggesting that the large bacterial community present a high specific activity. The increase of the WLR from 0.37 to 1.12 g l(-1)d(-1) decreased the colour and the chemical oxygen demand (COD) removal efficiencies from 90% to 55% and from 85% to 30%, respectively, explained by the decrease of the bacterial diversity and activity. The changes of the bacterial dominance had no affect on the reactor performances. However, the decrease of the bacterial diversity significantly affected the colour and the COD removal efficiencies. It should conclude that indigo dye-containing textile wastewater treatment required the concerted activity of multiple bacterial populations.     

Azadirachtin production by hairy root cultivation of Azadirachta indica in a modified stirred tank reactor

Present investigation involves hairy root cultivation of Azadirachta indica in a modified stirred tank reactor under optimized culture conditions for maximum volumetric productivity of azadirachtin. The selected hairy root line (Az-35) was induced via Agrobacterium rhizogenes LBA 920-mediated transformation of A. indica leaf explants (Coimbatore variety, India). Liquid culture of the hairy roots was developed in a modified Murashige and Skoog medium (MM2). To further enhance the productivity of azadirachtin, selected growth regulators (1.0?mg/l IAA and 0.025?mg/l GA₃), permeabilizing agent (0.5?% v/v DNBP), a biotic elicitor (1?% v/v Curvularia (culture filtrate)) and an indirectly linked biosynthetic precursor (50?mg/l cholesterol) were added in the growth medium on 15th day of the hairy root cultivation period in shake flask. Highest azadirachtin production (113?mg/l) was obtained on 25th day of the growth cycle with a biomass of 21?g/l DW. Further, batch cultivation of hairy roots was carried out in a novel liquid-phase bioreactor configuration (modified stirred tank reactor with polyurethane foam as root support) to investigate the possible scale-up of the established A. indica hairy root culture. A biomass production of 15.2?g/l with azadirachtin accumulation in the hairy roots of 6.4?mg/g (97.28?mg/l) could be achieved after 25?days of the batch cultivation period, which was ~27 and ~14?% less biomass and azadirachtin concentration obtained respectively, in shake flasks. An overall volumetric productivity of 3.89?mg/(l?day) of azadirachtin was obtained in the bioreactor.     

L-Tyrosine Production by Analog-resistant Mutants Derived from a Phenylalanine Auxotroph of Corynebacterium glutamicum

Mutants resistant to various phenylalanine- or tyrosine-analogs were isolated from a phenylalanine auxotroph of Corynebacterium glutamicum KY 10233 by treatment with N- methyl-N′-nitro-N-nitrose guanidine (NTG) and screened for L-tyrosine production. A mutant, 98–Tx–71, which is resistant to 3-aminotyrosine, p-aminophenylalanine, p-fluoro-phenylalanine, and tyrosine hydroxamate was found to produce L-tyrosine at a concentration of 13.5 mg/ml in the cane molasses medium containing 10% of sugar calculated as glucose. A tyrosine-sensitive mutant, pr–20 which was derived from 98–Tx–71 produced L-tyrosine at a concentration of 17.6 mg/ml. L-Tyrosine formation in the strain pr–20 was found to be still inhibited by L-phenylalanine though it was not inhibited by L-tyrosine. The L-tyrosine formation in the mutant was repressed neither by L-phenylalanine nor by L-tyrosine.