In vivo degradation behavior of photo-cross-linked star-poly(epsilon-caprolactone-co-D,L-lactide) elastomers

We have recently reported on the preparation of biodegradable elastomers through photo-cross-linking acrylated star-poly(epsilon-caprolactone-co-D,L-lactide). In this paper we assess the change in their physical properties during in vivo degradation in rats after subcutaneous implantation over a 12 week period. These parameter changes were compared to those observed in vitro. Two different cross-link densities were examined, representing the range from a high Young's modulus to a low Young modulus. Elastomers having a high cross-link density exhibited degradation behavior consistent with a surface erosion mechanism, and degraded at the same rate in vivo as observed in vitro. Young's modulus and the stress at break of these elastomers decreased linearly with the degradation time, while the strain at break decreased slowly. Elastomers having a low cross-link density exhibited a degradation mechanism consistent with bulk erosion. Young's modulus and the stress at break of these elastomers decreased slowly initially, followed by a marked increase in mechanical strength loss after 4 weeks. The elastomers were well tolerated by the rats over the 12 week period in vivo.     

Synthesis and characterization of thermoset biodegradable elastomers based on star-poly(epsilon-caprolactone-co-D,L-lactide)

Biodegradable elastomers represent a useful class of biomaterials. In this paper, we synthesize thermoset elastomers by utilizing the living nature of ring-opening polymerization of a star copolymer of D,L-lactide and epsilon-caprolactone initiated with glycerol and catalyzed by stannous 2-ethylhexanoate. The star copolymers were synthesized of varying molecular weight and monomer composition and cross-linked by compression molding using a dilactone, bis(epsilon-caprolactone-4-yl)propane dissolved in epsilon-caprolactone monomer. The elastomers were then characterized by differential scanning calorimetry and uniaxial tensile testing and their physical properties related to the nature of the star copolymer prepolymers. The results demonstrate a means of predictably altering the elastomer physical properties by adjusting the star copolymer prepolymer initial molecular weight and monomer ratio.     

Poly(caprolactone-co-oxo-crown ether)-based poly(urethane)urea for soft tissue engineering applications

Random copolymers of epsilon-caprolactone and 2-oxo-12-crown-4 ether, poly(CL-co-OC), were used as soft segments in the synthesis of a set of poly(urethane)urea thermoplastic elastomers. With increasing OC content, the soft segment crystallinity decreased, which influenced the mechanical properties: strain induced crystallization disappeared upon the introduction of OC into poly(CL). The material therefore became weaker, however, without a reduction in strain at break. All polymers showed mechanical properties that are suitable for soft tissue engineering. Degradation studies of poly(CL-co-OC) copolymers revealed a higher intrinsic rate of hydrolysis as compared to poly(CL). When at least two neighboring OC units were present in the soft segment, a jump in the intrinsic hydrolysis rate was observed. From this study we deduced an ideal OC:CL ratio for the thermoplastic elastomer soft segments for soft tissue engineering applications. An in vitro degradation study of these poly(urethane)urea showed an increased weight loss. Combined with the enhanced hydrophilicity and reduced crystallinity, we are confident that this will indeed lead to an increased degradation rate in vivo.     

Biodegradation of polyurethane acrylate with acrylated epoxidized soybean oil blend elastomers by Chaetomium globosum

This paper studies the biodegradation features of a novel blend of polyurethane acrylate-acrylated epoxidized soybean oil-based cross-linked polyurethane elastomers in the presence of the soft-rot fungus Chaetomium globosum. After the specimens were incubated at 28 °C for 90 and 130 days, the degree of fungal damage was measured by analysis of weight loss and mechanical properties. The biodegradation of the films was also evidenced by SEM and FTIR spectroscopic studies. After fungal attack, the FTIR spectra indicate a degradation of urethane and ester groups of the polyurethane and especially of the ester groups from the modified soybean oil part. The polyurethane blend films exposed to fungal attack suffered a loss in strength of up to 55% and a loss in elongation of up to 80%, depending on the content of acrylated epoxidized soybean oil. The biodegradation of the blends was also confirmed by SEM analyses. The biodegradation results show that samples with a high content of acrylated epoxidized soybean oil are more biodegradable than mere polyurethane acrylate. These biodegradable polymer blends present an optimum balance of physical properties and biodegradable properties with the potential for application as eco-friendly biomaterials.     

Physical properties of canola oil based polyurethane networks

A new generation polyol (generation-II) with significantly higher triol content and higher hydroxyl value was synthesized from canola oil by introducing a mild solvent (ethyl acetate) and a more efficient reductive reagent (zinc) to the previous synthetic procedure (Narine, S. S.; Yue, J.; Kong, X. J. Am. Oil Chem. Soc. 2007, 84, 173-179). Polyurethane (PUR) elastomers were prepared by reacting this type of polyol with aliphatic diisocyanates. The physical and thermal properties of the PUR elastomers were studied using dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) and compared to the elastomers made from the old generation polyol (generation-I). The concentration of elastically active network chains (nue) of the polymer networks was calculated based on rubber elasticity theory. Larger nue and narrower distribution of nue was observed in the case of the PURs prepared from the generation-II polyol. The relatively faster relaxation at higher temperature for this type of PUR elastomer, suggests a tighter cross-linked network structure by reducing the dangling chains effect. With the same OH/NCO molar ratio, the PURs prepared from the generation-II polyol showed higher glass transition temperatures (Tg), higher Young's modulus and tensile strength, and longer elongation at break.     

Substrate Resistance to Traction Forces Controls Fibroblast Polarization

The mechanics of fibronectin-rich extracellular matrix regulate cell physiology in a number of diseases, prompting efforts to elucidate cell mechanosensing mechanisms at the molecular and cellular scale. Here, the use of fibronectin-functionalized silicone elastomers that exhibit considerable frequency dependence in viscoelastic properties unveiled the presence of two cellular processes that respond discreetly to substrate mechanical properties. Weakly cross-linked elastomers supported efficient focal adhesion maturation and fibroblast spreading because of an apparent stiff surface layer. However, they did not enable cytoskeletal and fibroblast polarization; elastomers with high cross-linking and low deformability were required for polarization. Our results suggest as an underlying reason for this behavior the inability of soft elastomer substrates to resist traction forces rather than a lack of sufficient traction force generation. Accordingly, mild inhibition of actomyosin contractility rescued fibroblast polarization even on the softer elastomers. Our findings demonstrate differential dependence of substrate physical properties on distinct mechanosensitive processes and provide a premise to reconcile previously proposed local and global models of cell mechanosensing.     

The viscoelastic basis for the tensile strength of elastin

Purified aortic elastin displays failure behaviour characteristic of an amorphous, noncrystalizing elastomer with failure properties showing a strong dependence on viscoelastic behaviour. Tensile breaking stresses and breaking strains measured over a range of temperatures, hydration levels, and strain rates are reducible to single curves by the application of shift factors obtained from dynamic mechanical tests. The breaking stress of rubbery elastin is similar to that found in other elastomers, but glassy elastin is about an order of magnitude less strong than expected. We suggest elastin's ability to be strengthened through viscous dissipation of strain energy and crack tip blunting is limited by its fibrillar structure.     

Evaluation of biocompatibility and mechanical behavior of polyurethane elastomers based on chitin/1,4-butane diol blends

Chitin based polyurethane elastomers with potential as biomedical implants with tunable mechanical properties were synthesized by step growth polymerization techniques using poly(epsilon-caprolactone) (PCL) and 4,4'-diphenylmethane diisocyanate (MDI). The prepolymer was extended with different mass ratios of chitin and 1,4-butane diol (BDO). Molecular characterization was done using FTIR, 1H NMR and 13C NMR techniques. The mechanical properties of these polymers were improved with increase in the chitin contents. Optimum mechanical properties were obtained from elastomers extended with chitin in comparison to elastomers extended with BDO. Cytotoxicity of the synthesized polyurethane samples was affected by varying the chitin contents in the chemical composition of the final polyurethane (PU). It is revealed that the final polymers extended with chitin are preferred candidates for surgical threads with on going investigations into their in vitro biocompatibility and non-toxicity.     

Biodegradable polyurethane ureas with variable polyester or polycarbonate soft segments: effects of crystallinity, molecular weight, and composition on mechanical properties

Biodegradable polyurethane urea (PUU) elastomers are ideal candidates for fabricating tissue engineering scaffolds with mechanical properties akin to strong and resilient soft tissues. PUU with a crystalline poly(ε-caprolactone) (PCL) macrodiol soft segment (SS) showed good elasticity and resilience at small strains (<50%) but showed poor resilience under large strains because of stress-induced crystallization of the PCL segments, with a permanent set of 677 ± 30% after tensile failure. To obtain softer and more resilient PUUs, we used noncrystalline poly(trimethylene carbonate) (PTMC) or poly(δ-valerolactone-co-ε-caprolactone) (PVLCL) macrodiols of different molecular weights as SSs that were reacted with 1,4-diisocyanatobutane and chain extended with 1,4-diaminobutane. Mechanical properties of the PUUs were characterized by tensile testing with static or cyclic loading and dynamic mechanical analysis. All of the PUUs synthesized showed large elongations at break (800-1400%) and high tensile strength (30-60 MPa). PUUs with noncrystalline SSs all showed improved elasticity and resilience relative to the crystalline PCL-based PUU, especially for the PUUs with high molecular weight SSs (PTMC 5400 M(n) and PVLCL 6000 M(n)), of which the permanent deformation after tensile failure was only 12 ± 7 and 39 ± 4%, respectively. The SS molecular weight also influenced the tensile modulus in an inverse fashion. Accelerated degradation studies in PBS containing 100 U/mL lipase showed significantly greater mass loss for the two polyester-based PUUs versus the polycarbonate-based PUU and for PVLCL versus PCL polyester PUUs. Basic cytocompatibility was demonstrated with primary vascular smooth muscle cell culture. The synthesized families of PUUs showed variable elastomeric behavior that could be explained in terms of the underlying molecular design and crystalline behavior. Depending on the application target of interest, these materials may provide options or guidance for soft tissue scaffold development.     

Elastin: a representative ideal protein elastomer

During the last half century, identification of an ideal (predominantly entropic) protein elastomer was generally thought to require that the ideal protein elastomer be a random chain network. Here, we report two new sets of data and review previous data. The first set of new data utilizes atomic force microscopy to report single-chain force-extension curves for (GVGVP)(251) and (GVGIP)(260), and provides evidence for single-chain ideal elasticity. The second class of new data provides a direct contrast between low-frequency sound absorption (0.1-10 kHz) exhibited by random-chain network elastomers and by elastin protein-based polymers. Earlier composition, dielectric relaxation (1-1000 MHz), thermoelasticity, molecular mechanics and dynamics calculations and thermodynamic and statistical mechanical analyses are presented, that combine with the new data to contrast with random-chain network rubbers and to detail the presence of regular non-random structural elements of the elastin-based systems that lose entropic elastomeric force upon thermal denaturation. The data and analyses affirm an earlier contrary argument that components of elastin, the elastic protein of the mammalian elastic fibre, and purified elastin fibre itself contain dynamic, non-random, regularly repeating structures that exhibit dominantly entropic elasticity by means of a damping of internal chain dynamics on extension.     

Properties of film from splendid squid (Loligo formosana) skin gelatin with various extraction temperatures

Properties of film from splendid squid (Loligo formosana) skin gelatin extracted at different temperatures (50-80°C) were investigated. Tensile strength (TS) and elongation at break (EAB) of films decreased, but water vapour permeability (WVP) increased (P<0.05) as the extraction temperature increased. Increase in transparency value with coincidental decrease in lightness was observed with increasing extraction temperatures. Electrophoretic study revealed that degradation of gelatin became more pronounced with increasing extraction temperatures. As a consequence, their corresponding films had the lower mechanical properties. FTIR spectra of obtained gelatin films revealed the significant loss of molecular order of the triple helix. Thermogravimetric analysis indicated that F80 exhibited the higher heat susceptibility and weight loss. Loosen structure was observed in film prepared from gelatin with increasing extraction temperatures. Thus, the temperature used for gelatin extraction from splendid squid skin directly affected the properties of corresponding films.     

Conjugal Transfer of Plasmid-Borne Multiple Antibiotic Resistance in Streptococcus faecalis var. zymogenes

A strain of Streptococcus faecalis var. zymogenes, designated JH1, had high-level resistance to the antibiotics streptomycin, kanamycin, neomycin, erythromycin, and tetracycline. These resistances were lost en bloc from approximately 0.1% of cells grown in nutrient broth at 45 C. The frequency of resistance loss was not increased by growth in the presence of the "curing" agents acriflavine or acridine orange, but after prolonged storage in nutrient agar 17% of cells became antibiotic sensitive. Covalently closed circular deoxyribonucleic acid (DNA) molecules were isolated from the parental strain and from antibiotic-sensitive segregants by using cesium chloride-ethidium bromide gradients. DNA molecular species were identified by using neutral sucrose gradients. Strain JH1 contained two covalently closed circular DNA species of molecular weights 50 x 10(6) and 38 x 10(6). An antibiotic-sensitive segregant, strain JH1-9, had lost the larger molecular species. A second sensitive segregant, strain JH1-5, had also lost the larger molecular species but a new molecular species of approximate molecular weight 6 x 10(6) was present. The antibiotic resistances that were curable from the parental strain were transferred to antibiotic-sensitive strains of S. faecalis and to strain JH1-9, during mixed incubation in nutrient broth at 37 C. Data to be described are interpreted to suggest that the transfer is by a conjugal mechanism. Analysis of the plasmid species in recipient clones showed that all had received the plasmid of molecular weight 50 x 10(6). Strain JH1-5 was not a good recipient. Analysis of one successful recipient clone of JH1-5 revealed that it had gained the 50 x 10(6) molecular weight plasmid but lost the 6 x 10(6) molecular weight species. These data are interpreted to mean that the multiple antibiotic resistance is borne by a transferable plasmid of 50 x 10(6) molecular weight, and that in clone JH1-5 this plasmid suffered a large deletion leaving only a 6 x 10(6) remnant which was incompatible with the complete replicon.     

A mechanical evaluation of an elastic femoral prosthetic stem

Studies are being conducted in our laboratory to test the concept of introducing an elastomer to attenuate and damp forces applied to the bone interface in a major weightbearing joint replacement prosthesis. An analogue of a fully constrained intramedullary stem type prosthesis has been developed in a segmental femoral replacement prosthesis of the dog. The layer of silastic was introduced to damp forces at the bone-prosthesis interface. This paper describes the response of this elastomer prosthesis to torsional and bending loads, and defines the upper limits of elastomer strain. The low modulus silastic displayed surprisingly low strain for applied loads, particularly in bending tests, in this prosthetic configuration. The results of these mechanical studies serve as a bench mark for the eventual design and material selection of an elastomer for human prosthetic use.     

Flexible oxygen barrier films from spruce xylan

Arabinoglucuronoxylan was extracted from Norway spruce and films prepared by casting from aqueous solution. The sugar analysis and NMR confirmed that the spruce xylan was composed of arabinose, 4-O-methyl-glucuronic acid and xylose in a ratio of 1:2:11 respectively. Substitutions of 4-O-methyl-α-d-GlcpA at O₂ and of α-l-Araf at O₃ on the xylose backbone were found by NOE analysis. NOE cross-peaks indicated as well that there is at least one free xylose on the main chain present between two substitutions. Whether the distribution of side chains was random or in blocks was uncertain. The average molecular weight of the sample was determined by size exclusion chromatography to be 12,780 g/mol. Arabinoglucoronoxylan casting yielded transparent flexible films with an average stress at break of 55 MPa, strain at break of 2.7% and a Young's Modulus 2735 MPa. Wide-angle X-ray scattering analysis showed that the arabinoglucuronoxylan films were totally amorphous. Addition of sorbitol as plasticizer resulted in less strong but more flexible films (strain at break of 5%). Peaks of crystallinity could be seen in X-ray which corresponds to sorbitol crystallizing in distinct phases. The dynamic mechanical analysis showed that the arabinoglucuronoxylan film softened at a later relative humidity (80% RH) in comparison with plasticized films (60% RH). The films showed low oxygen permeability and thus have a potential application in food packaging.     

Contractility of single human dermal myofibroblasts and fibroblasts

Human dermal myofibroblasts, characterised by the expression of alpha-smooth muscle actin, are part of the granulation tissue and implicated in the generation of contractile forces during normal wound healing and pathological contractures. We have compared the contractile properties of single human dermal fibroblasts and human dermal myofibroblasts by culturing them on flexible silicone elastomers. The flexibility of the silicone substratum permits the contractile forces exerted by the cells to be measured [Fray et al., 1998: Tissue Eng. 4:273-283], without changing their expression of alpha-smooth muscle actin. The mean contractile force produced by myofibroblasts (2.2 microN per cell) was not significantly different from that generated by fibroblasts (2.0 microN per cell) when cultured on a substrata with a low elastomer stiffness. Forces produced by fibroblasts were unaffected by increases in elastomer stiffness, but forces measured for myofibroblasts increased to a mean value of 4.1 microN/cell. This was associated with a higher proportion of myofibroblasts being able to produce wrinkles on elastomers of high stiffness compared to fibroblasts. We discuss the force measurements at the single cell level, for both fibroblast and myofibroblasts, in relation to the proposed role of myofibroblasts in wound healing and pathological contractures.     

Microbial degradation of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in soils.

The microbial degradation of tensile test pieces made of poly(3-hydroxybutyrate) [P(3HB)] or a copolymer of 90% 3-hydroxybutyric acid and 10% 3-hydroxyvaleric acid was studied in soils incubated at a constant temperature of 15, 28, or 40 degrees C for up to 200 days. In addition, hydrolytic degradation in sterile buffer at temperatures ranging from 4 to 55 degrees C was monitored for 98 days. Degradation was measured through loss of weight (surface erosion), molecular weight, and mechanical strength. While no weight loss was recorded in sterile buffer, samples incubated in soils were degraded at an erosion rate of 0.03 to 0.64% weight loss per day, depending on the polymer, the soil, and the incubation temperature. The erosion rate was enhanced by incubation at higher temperatures, and in most cases the copolymer lost weight at a higher rate than the homopolymer. The molecular weights of samples incubated at 40 degrees C in soils and those incubated at 40 degrees C in sterile buffer decreased at similar rates, while the molecular weights of samples incubated at lower temperatures remained almost unaffected, indicating that molecular weight decrease is due to simple hydrolysis and not to the action of biodegrading microorganisms. The degradation resulted in loss of mechanical properties. From the samples used in the biodegradation studies, 295 dominant microbial strains capable of degrading P (3HB) and the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer in vitro were isolated and identified.(ABSTRACT TRUNCATED AT 250 WORDS)     

Plasticized waxy maize starch: effect of polyols and relative humidity on material properties

The plasticizing effect of different polyols such as glycerol, xylitol, sorbitol, and maltitol on waxy maize starch was investigated. The concentration of plasticizer was fixed at 33 wt % (dry basis of starch). The structure and mechanical performance of resulting films conditioned at different relative humidity levels were studied in detail. The effect of the plasticizer on the glass-rubber transition temperature (T(g)) and crystallinity was characterized using differential scanning calorimetry. It was found that T(g) decreases with increasing moisture content and decreasing molecular weight of the plasticizer. The water resistance of starch increased steadily with the molecular weight of the plasticizer and was directly proportional to the ratio of the end to total hydroxyl groups. As the molecular weight of the plasticizer increased, the brittleness of the dry system increased. However, the use of high molecular plasticizer allowed good mechanical properties of the moist material to be obtained in terms of both stiffness and elongation at break.     

Synthesis, characterization, and in vitro degradation of a biodegradable photo-cross-linked film from liquid poly(epsilon-caprolactone-co-lactide-co-glycolide) diacrylate

There has been little study on the effect of composition or molecular weight on the biodegradation rate of photo-cross-linked biodegradable aliphatic polyesters though such information is important for tissue engineering scaffolds. We have synthesized a new series of photopolymerizable linear poly(epsilon-caprolactone-co-lactide-co-glycolide) diacrylates with different molecular weights (Mn = 1800, 4800, and 9300 Da) and compositions (20%, 40%, and 60% epsilon-CL) and studied their biodegradation rates. The resultant oligomers were amorphous and appeared as viscous liquids at room temperature. Liquid-to-solid polymerization was carried out by UV irradiation in the presence of a photoinitiator. The photocuring yield was high (greater than 95%), and the photo-cross-linked polymers were amorphous and rubbery. Mechanical measurements showed that the polymers can be stretchable or rigid; the high molecular weight/low epsilon-CL network has a strain of 176% and a modulus of 1.66 MPa while the low molecular weight/high epsilon-CL network has a strain of 21% and a modulus of 12.3 MPa. In a 10 week in vitro biodegradation study, the polymers exhibited a two-stage degradation behavior. In the first stage, the polymer weight and strain remained almost constant, but a linear decrease in the Young's modulus (E) and ultimate stress (sigma) were observed. Lower oligomer molecular weight or epsilon-CL content correlated with a faster decrease in Young's modulus. In the second stage, which began when the Young's modulus dropped below 1 MPa, there was rapid weight loss and strain increase. The lower the epsilon-CL content, the earlier the second stage happened. Low molecular weight and high epsilon-CL content correlated with a longer modulus half-life (time for the modulus to degrade to 50% of its initial value). The degradation results suggest principles that may be helpful in predicting the biodegradation behavior of similar polymeric cross-linked networks. Films formed from these new polymers have excellent biocompatibility with smooth muscle cells.     

Evaluation of biocompatibility and mechanical behavior of chitin-based polyurethane elastomers. Part-II: Effect of diisocyanate structure

Chitin-based polyurethane elastomers having potential for biomedical applications with tunable mechanical properties were synthesized by step growth polymerization techniques using poly(?-caprolactone) (PCL) with different diisocyanates. The prepolymer was extended using chitin and/or 1,4-butane diol (BDO). The structures of the resulted polymers were determined by Fourier transform infrared (FTIR), ¹H NMR and ¹³C NMR spectroscopic techniques. The effect of structure of diisocyanates and chain extenders on mechanical properties and in vitro biocompatibility were investigated. The results revealed that the final polymers extended with chitin are preferred candidates for surgical threads with on going investigations into their in vitro biocompatibility and non-toxicity.     

褐腐真菌产生的低分子化合物对纤维素的解聚作用研究

糙皮侧耳（Pleurotusostreatus）、密粘褶菌（Gloeophyllumtrabeum）、洁丽香菇（Lentinuslepideus）等8株褐腐菌在滤纸上进行固体培养时,在培养初期,纤维素的聚合度均呈现大幅度下降,但不表现失重。培养过程中也未能检测出滤纸酶活力,只有少量内切葡聚糖酶活力。而且这8株菌都具有络合Fd3+和产生羟基自由基·OH的能力。由降解和解聚能力最强的密粘语菌的胞外酶液在SephadexLH-20上分离得到一可络合Fe3+的低分子多肽组分,它与H2O2具有协同降解纤维素的作用,其机制与Fenton's试剂作用相似。Fe2+与H2O2反应生成的·OH可使纤维素氧化断裂,使之成为短小纤维,从而大幅度降低聚合度。