Biological hydrogen production by anaerobic digestion of food waste and sewage sludge treated using various pretreatment technologies

The purpose of this study was to enhance the efficiency of anaerobic co-digestion with sewage sludge using pretreatment technologies and food waste. We studied the effects of various pretreatment methods (thermal, chemical, ultrasonic, and their combination) on hydrogen production and the characteristics of volatile fatty acids (VFAs) using sewage sludge alone and a mixture of sewage sludge and food waste. The pretreatment combination of alkalization and ultrasonication performed best, effecting a high solubilization rate and high hydrogen production (13.8 mL H₂/g VSS_consumed). At a food waste:pretreated sewage sludge ratio of 2:1 in the mixture, the peak hydrogen production value was 5.0 L H₂/L/d. As the production of hydrogen increased, propionate levels fell but butyrate concentrations rose gradually.     

New sludge pretreatment method to improve dewaterability of waste activated sludge

The enhancements of electrolysis-pretreated conditioning were investigated in this study. Normalized capillary suction time (CST) was used to evaluate sludge dewaterability. Extracellular polymeric substance (EPS) concentration, viscosity and scanning electron microscopy (SEM) were determined to explain the observed changes in conditioning process. It indicated that pretreatment at 50 v and 5 min with Ti/RuO₂ anode was determined to be the optimal condition, which generated the lowest normalized CST and optimal soluble EPS concentration, leading to the decreasing of viscosity. EPS had positive correlation with the normalized CST. Subjecting to a combination of electrolysis pretreatment and flocculants conditioning, 50% dosage of cationic polyacrylamide (PAM) could be reduced. When co-conditioned with electrolysis and polymerization ferric sulfate (PFS), it did not present any clear advantages over PFS conditioning alone. Furthermore, SEM investigation indicated that electrolysis pretreatment could rupture sludge, release the interstitial water and extracellular substances, especially protein and polysaccharide, and consequently enhance its dewaterability.     

Effects of microwave and alkali induced pretreatment on sludge solubilization and subsequent aerobic digestion

Individual and combined effects of microwave (MW) and alkali pretreatments on sludge disintegration and subsequent aerobic digestion of waste activated sludge (WAS) were studied. Pretreatments with MW (600 W-85 °C-2 min), conventional heating (520 W-80 °C-12 min) and alkali (1.5 g NaOH/L - pH 12-30 min) achieved 8.5%, 7% and 18% COD solubilization, respectively. However, combined MW-alkali pretreatment synergistically enhanced sludge solubilization and achieved 46% COD solubilization, 20% greater than the additive value of MW alone and alkali alone (8.5 + 18% = 26.5%). Moreover, the results of the batch aerobic digestion study on MW-alkali pretreated sludge showed 93% and 63% reductions in SCOD and VSS concentrations, respectively, at 16 days of SRT. The VSS reduction was 20% higher than that of WAS without pretreatment.     

The effect of acid pretreatment on the anaerobic digestion and dewatering of waste activated sludge

Waste activated sludge (WAS) is difficult to degrade in anaerobic digestion systems and pretreatments have been shown to speed up the hydrolysis stage. Here the effects of acid pretreatment (pH 6-1) using HCl on subsequent digestion and dewatering of WAS have been investigated. Optimisation of acid dosing was performed considering digestibility benefits and level of acid required. Pretreatment to pH 2 was concluded to be the most effective. In batch digestion this yielded the same biogas after 13 days as compared to untreated WAS at 21 days digestion. In semi-continuous digestion experiments (12 day hydraulic retention time at 35 °C) it resulted in a 14.3% increase in methane yield compared to untreated WAS, also Salmonella was eradicated in the digestate. Dewatering investigations suggested that the acid pretreated WAS required 40% less cationic polymer addition to achieve the same cake solid content. A cost analysis was also carried out.     

Microbial analysis of a phototrophic sludge producing hydrogen from acidified wastewater

Based on DNA-cloning analysis, the microbial community of a phototrophic sludge producing H₂ from an acidified wastewater was composed of 81% of a species resembling Rhodobacter capsulatus (with 99.2% similarity) and two unidentified species of the Bacillus/Clostridium group. The sludge produced a biogas comprising 82 ± 2% H₂, 13 ± 2% CO₂, 4.5 ± 0.5% N₂, and 0.5 ± 0.2% H₂S.     

The isolation and microbial community analysis of hydrogen producing bacteria from activated sludge

AIMS: To profile the fractions of bacteria in heat-treated activated sludge capable of producing hydrogen and subsequently to isolate those organisms and confirm their ability to produce hydrogen. METHODS AND RESULTS: Profiling the community composition of the microflora in activated sludge using 16S rRNA gene-directed polymerase chain reaction-denaturing gradient gel electrophoresis suggested that a majority of bacteria were various Clostridium species. This was confirmed by clone library analysis, where 80% of the cloned inserts were Clostridium sp. A total of five isolates were established on solid media. Three of them, designated as W1, W4 and W5, harboured the hydrogenase gene as determined by PCR and DNA sequence analysis (99% similarity). These isolates were similar to Clostridium butyricum and Clostridium diolis as determined by 16S rRNA gene sequence. A maximum hydrogen production yield of 220 ml H(2) g(-1) glucose was achieved by W5, which was grown on improved mineral medium by batch fermentation without pH adjustment and nitrogen sparging during fermentation. Accumulation of malic acid and fumaric acid during hydrogen fermentation might lead to higher hydrogen yields for W4 and W5. W1 is the first reported Clostridium species that can tolerate microaerobic conditions for producing hydrogen. CONCLUSION: Clostridium species in heat-treated activated sludge were the most commonly identified bacteria responsible for hydrogen production. Specific genetic markers for strains W1, W4 and W5 would be of great utility in investigating hydrogen production at the molecular level. Two previously described primer sets targeting hydrogenase genes were shown not to be specific, amplifying other genes from nonhydrogen producers. SIGNIFICANCE AND IMPACT OF THE STUDY: Clostridium species isolated from heat-treated activated sludge were confirmed as hydrogen producers during dark hydrogen fermentation. The isolates will be useful for studying hydrogen production from wastewater, including the process of gene regulation and hydrogenase activity.     

Low temperature thermo-chemical pretreatment of dairy waste activated sludge for anaerobic digestion process

An investigation into the influence of low temperature thermo-chemical pretreatment on sludge reduction in a semi-continuous anaerobic reactor was performed. Firstly, effect of sludge pretreatment was evaluated by COD solubilization, suspended solids reduction and biogas production. At optimized condition (60 °C with pH 12), COD solubilization, suspended solids, reduction and biogas production was 23%, 22% and 51% higher than the control, respectively. Secondly, semi-continuous process performance was studied in a lab-scale semi-continuous anaerobic reactor (5 L), with 4 L working volume. With three operated SRTs, the SRT of 15 days was found to be most appropriate for economic operation of the reactor. Combining pretreatment with anaerobic digestion led to 80.5%, 117% and 90.4% of TS, SS and VS reduction respectively, with an improvement of 103% in biogas production. Thus, low temperature thermo-chemical can play an important role in reducing sludge production.     

The influence of the energy absorbed from microwave pretreatment on biogas production from secondary wastewater sludge

In this study, microwave treatment is analyzed as a way to accelerate the hydrolysis in anaerobic digestion of municipal wastewater sludge. The influence of the absorbed energy, power and athermal microwave effect on organic matter solubilization and biogas production has been studied. In addition, a novel method that considers the absorbed energy in the microwave system is proposed, in order to obtain comparable experimental results. The absorbed energy is calculated from an energy balance.The highest solubilization was achieved using 0.54 kJ/ml at 1000 W, where an increment of 7.1% was observed in methane production, compared to the untreated sample. Using a higher energy value (0.83 kJ/ml), methane production further increased (to 15.4%), but solubilization decreased. No power influence was found when 0.54 kJ/ml was applied at 1000, 600 and 440 W. Microwave heating was compared to conventional heating in two different experimental setups, providing similar methane yields in all cases.     

Disinfection of hospital waste sludge using hypochlorite and chlorine dioxide

Hypochlorite and chlorine dioxide were used to disinfect hospital waste-water sludge. Their abilities to inactivate pathogenic micro-organisms were compared. Reductions in indigenous coliform organisms and Pseudomonas aeruginosa were estimated. The results indicate that hypochlorite is a better disinfectant than chlorine dioxide for coliforms. Higher disinfection efficiency was obtained by treating a lower concentration of sludge. In addition, a higher agitation speed gave a higher disinfection efficiency with hypochlorite. The disinfection efficiencies of both disinfectants were higher against settled sludge than against thickened sludge. Therefore, it is recommended that disinfection should be performed on settled sludge rather than in a thickening tank.     

Efficient,high-speed methane fermentation for sewage sludge using subcritical water hydrolysis as pretreatment

A novel biomass-energy process for the production of methane from sewage sludge using a subcritical water (sub-CW) hydrolysis reaction as pretreatment is proposed. The main substances of sewage sludge hydrolyzed by sub-CW at 513 K for 10 min were acetic acid, formic acid, pyroglutamic acid, alanine, and glycine. Fermentation experiments were conducted in an anaerobic-sludge reactor for two different samples: real sewage sludge and a model solution containing components typically produced by the sub-CW pretreatment of sewage sludge. In the experiment for the sub-CW pretreatment of sewage sludge, methane generation was twice that for non-pretreatment after 3 days of incubation. In the model experiment, the methane conversion was about 40% with the application of mixture of organic acids and amino acids after 5 days of incubation. Furthermore, the methane conversion was about 60% for 2 days when only organic acids, such as acetic acid and formic acid, were applied. Because acetic acid is the key intermediate and main precursor of the methanogenesis step, fermentation experiments were conducted in an anaerobic-sludge reactor with high concentrations of acetic acid (0.01–0.1 M). Nearly 100% of acetic acid was converted to methane and carbon dioxide in 1–3 days.     

葡萄糖废液生产建筑用高效减水剂

以溴水为氧化剂,将制药厂葡萄糖废流氧化成葡萄糖酸,生产建筑用高效混凝土减水剂葡萄糖酸钠,转化率可达80％以上。     

Degradation of hyaluronan by ultrasonication in comparison to microwave and conventional heating

Hyaluronan (hyaluronic acid, HA) was depolymerised by ultrasonication (US), microwave irradiation (MW) and conventional heating (CH), and the effect of pH and oxidants was investigated. The degradation was followed by viscometry and size exclusion chromatography coupled with low-angle light scattering. The results demonstrated that depolymerisation of HA by US leveled off to a limiting molecular mass, and the degradation was significantly enhanced by acidic and alkaline pH only in the presence of oxidants. In contrast to US, the course of depolymerisation by MW was strongly pH-dependent, and the degradation rate increased with decreasing pH. The expected enhancement of depolymerisation by MW in comparison to CH was marked only at very short heating time at pH <4. The NMR and FTIR spectral analyses indicated that HA in the whole M_w-range studied retained almost the backbone of the parent polysaccharide independently on the degradation method used. At harsh degradation conditions (long-term treatments, particularly at acidic pH or alkaline pH and in presence of oxidants) the depolymerisation was accompanied by destruction of both constituent sugar residues and formation of unsaturated structures detectable by UV-absorption at 230–240 and 260–270 nm. US-assisted oxidative degradation under mild reaction conditions was shown to be the most appropriate procedure to reduce the molecular mass of HA to 100 kDa without significant chemical modification of the polysaccharide.     

Hydrogen production from sewage sludge using mixed microflora inoculum: effect of pH and enzymatic pretreatment

Hydrogen was successfully produced by fermenting primary sewage sludge which had been both heat treated and digested with a commercially available enzyme preparation. When either heat treatment or enzymatic digestion were not used, no hydrogen was produced during fermentation. Heat treated mesophilic anaerobic sludge was used as an inoculum rather than a pure microbial culture. Fermentation was conducted at pH levels ranging from of 4.5 to 7.0. When fermentation took place at pH 5.5 a peak hydrogen production rate of 3.75 ml min(-1) was observed. At this pH the hydrogen yield was 0.37 mol H(2)mol(-1) carbohydrate, equivalent to 18.14L H(2)kg(-1) dry solids.     

Production of bio-fuels by high temperature pyrolysis of sewage sludge using conventional and microwave heating

The pyrolysis of sewage sludge was investigated using microwave and electrical ovens as the sources of heat, and graphite and char as microwave absorbers. The main objective of this work was to maximize the gas yield and to assess its quality as a fuel and as a source of hydrogen or syngas (H2 + CO). Both gases were produced in a higher proportion by microwave pyrolysis than by conventional pyrolysis, with a maximum value of 38% for H2 and 66% for H2 + CO. The oils obtained were also characterized using FTIR and GC-MS. The use of conventional electrical heating in the pyrolysis of sewage sludge produced an oil that could have a significant environmental and toxicological impact. Conversely, microwave pyrolysis still preserved some of the functional groups of the initial sludge such as aliphatic and oxygenated compounds, whereas no heavy PACs were detected.     

Production of hydrogen from marine macro-algae biomass using anaerobic sewage sludge microflora

Hydrogen was produced from various marine macro-algae (seaweeds) through anaerobic fermentation using an undefined bacterial consortium. In this study, anaerobic fermentation from various marine macro-algae for Ulva lactuca, Porphyra tenera, Undaria pinnatifida, and Laminaria japonica was studied. From this analysis Laminaria japorica was determined to be the optimum substrate for hydrogen production. When L. japornica was used as the carbon source for enhanced hydrogen production, the optimum fermentation temperature, substrate concentration, initial pH, and pretreatment condition were determined to be 35°C, 5%, 7.5, and BT120 (Ball mill and thermal treatments at 120°C for 30 min), respectively. In addition, hydrogen production was improved when the sludge was heat-treated at 65°C for 20 min. Under these conditions, about 4,164 mL of hydrogen was produced from 50 g/L of dry algae (L. japonica) for 50 h, with a hydrogen concentration around 34.4%. And the maximum hydrogen production rate and yield were found to be 70 mL/L·h and 28 mL/g dry algae, respectively.     

Feasibility of using ultrasonic irradiation to recover active biomass from waste activated sludge

Under typical operating conditions, the microbial fraction of activated sludge flocs is approximately 40% by weight. The objective of this research is to evaluate the feasibility of using ultrasonic irradiation to disrupt activated sludge flocs allowing for the subsequent separation of active and inactive fractions. If separation of floc components is possible, then methods may be incorporated into wastewater treatment plant operations whereby only the inactive fraction of floc is wasted (i.e., of waste activated sludge, WAS), which in turn could increase the overall effective biological solids retention time, leading to increased process robustness with no net increase in reactor size. The results indicate that ultrasonic irradiation of WAS at 800 Wl(-1) followed by 30 min of settling can produce a supernatant with heterotrophic specific oxygen uptake rates (SOURs) of over two times the SOUR measured in the bulk mixed liquor. Under these conditions 26% of the initial heterotrophic activity was recovered within only 11% of the initial volatile mass. Similarly, autotrophic analysis revealed that nitrifying organisms, while sensitive to the effects of ultrasonic irradiation, can be separated from the activated sludge floc and recovered. An irradiation density of 200 Wl(-1) with an exposure time between 1 and 2 min produced a supernatant with a specific ammonia removal rate of over two times the initial mixed liquor rate.     

Degradation and characteristic changes of organic matter in sewage sludge using microbial fuel cell with ultrasound pretreatment

Microbial fuel cell (MFC) could be an efficient sludge treatment unit in regard of rates and extents of total chemical oxygen demand (TCOD) removal, particularly when ultrasound was applied to pretreat the sludge. This study characterized the organic matter in sludge before and after MFC treatment, with or without ultrasound as a pretreatment stage. The 5-d MFC tests with electric load significantly enhanced TCOD removal rate from 11.3% to 19.2% for raw sludge and from 25% to 57% for sludge pretreated with >0.6 W ml^?1 ultrasound, using conventional anaerobic digestion test (without electric load) as control. The aromatic proteins, soluble microbial byproduct-like fluorescent compounds and carboxylic components, aliphatic components (C–H related), hydrocarbon and carbohydrate materials were identified to be principally released by ultrasound pretreatment and the fuels in the present MFC study.     

Effect of sulphidogenesis on acid-phase digestion of waste activated sludge

This paper reports the influence of sulfate-reducing bacterial activity on acidogenic digestion of waste activated sludge (WAS). A series of experiments was conducted by feeding WAS to a 10-l, completely mixed, mesophilic reactor maintained at pH 5.0 under sulfidogenic and non-sulfidogenic conditions. Analyses of volatile fatty acids indicated that the productions of acetic and propionic acids were slightly increased by sulfidogenic activity at 218 mg/l level of sulfate when COD sulfate ratio was 55:1. Higher amounts of methanol, ethanol and hydrogen were observed in the non-sulfidogenic condition, but ammonia was lower than in the moderate sulfidogenic runs. At 0.63 kg VS/m³ d loading rate the hydrolysis was above 90% in both moderate sulfidogenic and non- sulfidogenic runs. The results of these experiments showed the possible influence of moderate sulfidogenesis in the protein degradation of WAS anaerobic digestion. However, the acid-phase digestion was adversely affected by increasing the sulfate concentration to 400 mg/l.