Immobilization of urease using glycidyl methacrylate grafted nylon-6-membranes

The graft copolymerization of glycidyl methacrylate (GMA) onto nylon-6-membrane using benzophenone (BP) as an initiator was carried out in an alcoholic aqueous solution. The acrylic double bond of GMA participated in the grafting onto the nylon-6-membrane backbone with the epoxy groups remaining unaffected. At the end of the grafting reaction, urease was immobilized onto the modified membrane. BP concentration, GMA concentration and organic solvent seperation were studied by determining the grafting percentage. The influence of urease concentration on the immobilization efficiency was also studied. With keeping other conditions constant, the optimum conditions were shown as following [BP]: 5 × 10⁻² mM; [GMA]: 10 M; [urease]: 10 mg/ml, organic solvent: methanol.     

Immobilization of lipase on epoxy-activated Purolite® A109 and its post-immobilization stabilization

In this study, Purolite^® A109, polystyrenic macroporous resin, was used as immobilization support due to its good mechanical properties and high particle diameter (400 μm), which enables efficient application in enzyme reactors due to lower pressure drops. The surface of support had been modified with epichlorhydrine and was tested in lipase immobilization. Optimized procedure for support modification proved to be more efficient than conventional procedure for hydroxy groups (at 22 °C for 18 h), since duration of procedure was shortened to 40 min by performing modification at 52 °C resulting with almost doubled concentration of epoxy groups (563 μmol g⁻¹). Lipase immobilized on epoxy-modified support showed significantly improved thermal stability comparing to both, free form and commercial immobilized preparation (Novozym^® 435). The highest activity (47.5 IU g⁻¹) and thermal stability (2.5 times higher half-life than at low ionic strength) were obtained with lipase immobilized in high ionic strength. Thermal stability of immobilized lipase was further improved by blocking unreacted epoxy groups on supports surface with amino acids. The most efficient was treatment with phenylalanine, since in such a way blocked immobilized enzyme retained 65% of initial activity after 8 h incubation at 65 °C, while non-blocked derivative retained 12%.     

Enzymatic transformation of 2-O-α-d-glucopyranosyl-l-ascorbic acid (AA-2G) by immobilized α-cyclodextrin glucanotransferase from recombinant Escherichia coli

This work aims to produce 2-O-α-d-glucopyranosyl-l-ascorbic acid (AA-2G) from ascorbic acid and β-cyclodextrin with immobilized α-cyclodextrin glucanotransferase (α-CGTase) from recombinant Escherichia coli. Molecular sieve (SBA-15) was used as an adsorbent, and sodium alginate was used as a carrier, and glutaraldehyde (GA) was used as a cross-linker. The effects of several key variables on α-CGTase immobilization were examined, and optimal immobilization conditions were determined as the following: glutaraldehyde (GA, cross-linker) 0.01% (v/v), SBA-15 (adsorbent) 2 g/L, CaCl₂ 3 g/L, sodium alginate 20 g/L, adsorption time 3 h, and immobilization time 1 h. In comparison with free α-CGTase, immobilized α-CGTase had a similar optimal pH (5.5) and a higher optimal temperature (45 °C). The continuous production of AA-2G from ascorbic acid and β-cyclodextrin in the presence of immobilized α-CGTase was carried out, and the highest AA-2G production reached 21 g/L, which was 2-fold of that with free α-CGTase. The immobilization procedure developed here was efficient for α-CGTase immobilization, which was proved to be a prospective approach for the enzymatic production of AA-2G.     

Influence of whole microalgal cell immobilization and organic solvent on the bioconversion of androst-4-en-3,17-dione to testosterone by Nostoc muscorum

The use of free, immobilized and reused immobilized cells of the microalga Nostoc muscorum was studied for bioconversion of androst-4-en-3,17-dione (AD) to testosterone in hexadecane. Among polymers such as agar, agarose, κ-carrageenan, polyacrylamide, polyvinyl alcohol, and sodium alginate that were examined for cell entrapment, sodium alginate with a concentration of 2% (w/v) proved to be the proper matrix for N. muscorum cells immobilization. The bioconversion characteristics of immobilized whole algal cells at ranges of temperatures, substrate concentrations, and shaking speeds were studied followed by a comparison with those of free cells. The conditions were 30 °C, 0.5 g/L, and 100 rpm, respectively. The immobilized N. muscorum showed higher yield (72 ± 2.3%) than the free form (24 ± 1.3%) at the mentioned conditions. The bioconversion yield did not decrease during reuse of immobilized cells and remained high even after 5 batches of bioreactions while Na-alginate 3% was used; however, reuse of alginate 2% beads did not give a satisfactory result.     

Preparation of active corn peptides from zein through double enzymes immobilized with calcium alginate–chitosan beads

Double enzymes (alcalase and trypsin) were effectively immobilized in a composite carrier (calcium alginate–chitosan) to produce immobilized enzyme beads referred to as ATCC. The immobilization conditions for ATCC were optimized, and the immobilized enzyme beads were characterized. The optimal immobilization conditions were 2.5% of sodium alginate, 10:4 sodium alginate to the double enzymes, 3:7 chitosan solution to CaCl₂ and 2.5 h immobilization time. The ATCC beads had greatly enhanced stability and good usability compared with the free form. The ATCC residual activity was retained at 88.9% of DH (degree of hydrolysis) after 35 days of storage, and 36.0% of residual activity was retained after three cycles of use. The beads showed a higher zein DH (65.8%) compared with a single enzyme immobilized in the calcium alginate beads (45.5%) or free enzyme (49.3%). The ATCC kinetic parameters V_max and apparent K_m were 32.3 mL/min and 456.62 g⁻¹, respectively. Active corn peptides (CPs) with good antioxidant activity were obtained from zein in the ethanol phase. The ATCC might be valuable for preparing CPs and industrial applications.     

Application of cellulase-polyamidoamine dendrimer-modified silica for microwave-assisted chitosan enzymolysis

Polyamidoamine dendrimer (PAMAM) is one of a number of dendritic polymers with a precise molecular structure, high geometric symmetry, and a large number of terminal groups. In this study, PAMAM was grafted onto the surface of silica by microwave irradiation and characterized by Fourier transform infrared spectroscopy and elemental analysis. A novel immobilized cellulase was developed based on enzyme immobilization onto the prepared PAMAM-grafted silica and applied in microwave-assisted chitosan enzymolysis. The results show that the efficiency of cellulase immobilization increased with increasing generations of PAMAM. A high enzymatic hydrolysis efficiency was obtained for a 7 mg ml^?1 chitosan solution at pH 6.2 and 50 °C with 40 W microwave-assisted enzymolysis (20 min) compared with a conventional enzymolysis protocol (3 h). The experimental results indicate that this rapid and efficient enzymolysis method combines the advantages of both PAMAM and microwave-assisted technology, which can be adapted to high-throughput enzyme assay in biochemical and clinical research.     

Production of isomaltulose using Erwinia sp. D12 cells: Culture medium optimization and cell immobilization in alginate

Isomaltulose is a structural isomer of sucrose commercially used in food industries. Glucosyltransferase produced by Erwinia sp. D12 catalyses an intramolecular transglucosylation of sucrose giving isomaltulose. An experimental Design and Response Surface Methodology were applied for the optimization of the nutrient concentration in the culture medium for enzyme production in shaken flasks at 200 rpm and 30 °C. A higher production of glucosyltransferase (7.47 Uml⁻¹) was observed in the culture medium containing sugar cane molasses (160 gl⁻¹), bacteriological peptone (20 gl⁻¹) and yeast extract Prodex Lac SD^® (15 gl⁻¹) after 8 h, at 30 °C. The highest production of glucosyltransferase in the 6.6-l bioreactor (14.6 Uml⁻¹) was obtained in the optimized culture medium after 10 h at 26 °C. When Erwinia sp. D12 cells were immobilized in sodium alginate, it was verified that sodium alginate solution A could be substituted by a cheaper one, sodium alginate solution B. Using a 40% cell suspension and 2% sodium alginate solution B for cell immobilization in a packed-bed reactor, 64.1% conversion of sucrose to isomaltulose was obtained. The packed-bed reactor with immobilized cells plus glutaraldehyde and polyethylenimine solutions remained in a pseudo-steady-state for 180 h.     

Graft copolymerization of acrylamide on chitosan-co-chitin and its application for immobilization of Aspergillus sp. RL2Ct cutinase

The synthesis of chitosan (Chs) and chitin (Chi) copolymer and grafting of acrylamide (AAm) onto the synthesized copolymer have been carried out by chemical methods. The grafted copolymer was characterized by FTIR, SEM and XRD. The extracellular cutinase of Aspergillus sp. RL2Ct (E.C. 3.1.1.3) was purified to 4.46 fold with 16.1% yield using acetone precipitation and DEAE sepharose ion exchange chromatography. It was immobilized by adsorption on the grafted copolymer. The immobilized enzyme was found to be more stable then the free enzyme and has a good binding efficiency (78.8%) with the grafted copolymer. The kinetic parameters K_M and V_max for free and immobilized cutinase were found to be 0.55 mM and 1410 μmol min⁻¹ mg⁻¹ protein, 2.99 mM and 996 μmol min⁻¹ mg⁻¹ protein, respectively. The immobilized cutinase was recycled 64 times without considerable loss of activity. The matrix (Chs-co-Chi-g-poly(AAm)) prepared and cutinase immobilized on the matrix have potential applications in enzyme immobilization and organic synthesis respectively.     

Electrostatic immobilization of pectinase on negatively charged AOT-Fe3O4 nanoparticles

Enzyme immobilization on magnetic nanoparticles (MNPs) has been a field of intense studies in biotechnology during the past decade. The present study suggests MNPs negatively charged by docusate sodium salt (AOT) as a support for pectinase immobilization. AOT is a biocompatible anionic surfactant which can stabilize MNPs. Electrostatic adsorption can occur between enzyme with positive charge and oppositely charged surface of MNPs (ca. 100 nm). The effect of three factors, i.e. initial enzyme concentration, aqueous pH and AOT concentration in different levels was investigated on pectinase immobilization. Maximum specific activity (1.98 U/mg enzyme) of immobilized pectinase and maximum enzyme loading of 610.5 mg enzyme/g support was attained through the experiments. Initial enzyme concentration is significantly important on both loading and activity of immobilized enzyme, while pH and AOT concentration only affect the amount of immobilized enzyme. Immobilized enzyme on MNPs was recovered easily through magnetic separation. At near pH of immobilization, protein leakage in reusability of immobilized enzyme was low and activity loss was only 10–20% after six cycles. Since pH is associated with immobilization by electrostatic adsorption, the medium pH was changed to improve the release of protein from the support, as well. MNPs properties were investigated using Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FT-IR) spectroscopy, and Dynamic Light Scattering (DLS) analysis.     

Immobilization of cellulase on polyamidoamine dendrimer-grafted silica

Polyamidoamine dendrimer (PAMAM) is one of a number of dendritic polymers with precise molecular structure, highly geometric symmetry, and a large number of terminal groups, and is suitable to carry biomolecules due to its affinity and biocompatibility. In this study, PAMAM was grafted onto the surface of silica by microwave irradiation. A novel media was developed through immobilizing cellulase onto the prepared PAMAM-grafted silica by adsorption and crosslinking methods and applied in hydrolysis of carboxymethyl cellulose. The results demonstrate that the enzyme binding capacity and enzymolysis efficiency increased with generations of PAMAM. The properties of the immobilized cellulase-PAMAM-grafted silica were investigated, which possessed high enzymatic activity and exhibited better stability with respect to pH, temperature compared with free enzyme. The optimal immobilization conditions for adsorption and crosslinking method were respectively obtained at 5 and 4 mg ml⁻¹ cellulase for 2 h of immobilization. A high enzymolysis efficiency was achieved by employing pH 4.8 and 5.8 substrate solution at 60 °C for adsorbed and crosslinked cellulase, respectively. After repeated three run cycles, the retained activities were found to be 75% and 82%. The results indicate that the PAMAM has a good performance as a carrier, and can be potentially adapted to support other biomacromolecules.     

Immobilization of urease on vapour phase stain etched porous silicon

Porous silicon layers fabricated by the reaction-induced vapor phase stain etch method were coated with 5% polyethylenimine. Urease from Canavalia brasiliensis beans was immobilized on this support through covalent linking with 2.5% glutaraldehyde. The pH and temperature profile of the immobilized and free urease exhibited higher activity at pH 6.5 and 37 °C. After being stored for 30 days at 4 °C, the immobilized enzyme had 75% of the initial activity. The maximum apparent Michaelis constant for free urease (K_m) was 94.33 mM whereas for immobilized urease was 53.04 mM. The maximum reaction velocity (V_max) for free urease was 3.51 mmol/min and for immobilized urease was 1.57 mmol/min.     

Effect of changing the nanoscale environment on activity and stability of nitrate reductase

Nitrate reductase (NR) is employed for fabrication of nitrate sensing devices in which the enzyme in immobilized form is used to catalyze the conversion of nitrate to nitrite in the presence of a suitable cofactor. So far, instability of immobilized NR due to the use of inappropriate immobilization matrices has limited the practical applications of these devices. Present study is an attempt to improve the kinetic properties and stability of NR using nanoscale iron oxide (nFe₃O₄) and zinc oxide (nZnO) particles. The desired nanoparticles were synthesized, surface functionalized, characterized and affixed onto the epoxy resin to yield two nanocomposite supports (epoxy/nFe₃O₄ and epoxy/nZnO) for immobilizing NR. Epoxy/nFe₃O₄ and epoxy/nZnO support could load as much as 35.8 ± 0.01 and 33.20 ± 0.01 μg/cm² of NR with retention of about 93.72 ± 0.50 and 84.81 ± 0.80% of its initial activity respectively. Changes in surface morphology and chemical bonding structure of both the nanocomposite supports after addition of NR were confirmed by scanning electron microscopy (SEM) and fourier transform infrared spectroscopy (FTIR). Optimum working conditions of pH, temperature and substrate concentration were ascertained for free as well as immobilized NR preparations. Further, storage stability at 4 °C and thermal stability between 25–50 °C were determined for all the NR preparations. Analytical applications of immobilized NR for determination of soil and water nitrates along with reusability data has been included to make sure the usefulness of the procedure.     

Reversible immobilization of catalase on fibrous polymer grafted and metal chelated chitosan membrane

Poly(itaconic acid) grafted and/or Fe(III) ions incorporated chitosan membranes were used for reversible immobilization of catalase (from bovine liver) via adsorption. The influences of pH and initial catalase concentration on the immobilization capacities of the CH-g-poly(IA) and CH-g-poly(IA)-Fe(III) membranes have been investigated in a batch system. Maximum catalase adsorption onto CH-g-poly(IA) and CH-g-poly(IA)-Fe(III) membrane were found to be 6.3 and 37.8 mg/g polymer at pH 5.0 and 6.5, respectively. The CH-g-poly(IA)-Fe(III) membrane with high catalase adsorption capacity was used in the rest of the study. The K_m value for immobilized catalase on CH-g-poly(IA)-Fe(III) (25.8 mM) was higher about 1.6-fold than that of free enzyme (13.5 mM). Optimum operational temperature was observed at 40 °C, a 5 °C higher than that of the free enzyme and was significantly broader. The optimum operational pH was same for both free and immobilized catalase (pH 7.0). Thermal stability was found to increase with immobilization. Free catalase lost all its activity within 20 days whereas immobilized catalase lost 23% of its activity during the same incubation period. It was observed that the same support enzyme can be repeatedly used for immobilization of catalase after regeneration without significant loss in adsorption capacity or enzyme activity. In addition, the CH-g-poly(IA)-Fe(III) membrane prepared in this work showed promising potential for various biotechnological applications.     

A novel method for the immobilization of glucoamylase onto polyglutaraldehyde-activated gelatin

A novel method was developed for the immobilization of glucoamylase from Aspergillus niger. The enzyme was immobilized onto polyglutaraldehyde-activated gelatin particles in the presence of polyethylene glycol and soluble gelatin, resulting in 85% immobilization yield. The immobilized enzyme has been fully active for 30 days. In addition, the immobilized enzyme retained 90 and 75% of its activity in 60 and 90 days, respectively. The enzyme optimum conditions were not affected by immobilization and the optimum pH and temperature for free and immobilized enzyme were 4 and 65 °C, respectively. The kinetic parameters for the hydrolysis of maltodextrin by free and immobilized glucoamylase were also determined. The K_m values for free and immobilized enzyme were 7.5 and 10.1 g maltodextrin/l, respectively. The V_max values for free and immobilized enzyme were estimated as 20 and 16 μmol glucose/(min μl enzyme), respectively. The newly developed method is simple yet effective and could be used for the immobilization of some other enzymes.     

Surfactant-mediated permeabilization of Pseudomonas putida KT2440 and use of the immobilized permeabilized cells in biotransformation

Surfactants were used to permeabilize cells of Pseudomonas putida KT2440 so as to maximize retention of the arginine deiminase (ADI) activity within the treated cells. The surfactants cetyltrimethylammoniumbromide (CTAB), sodium dodecyl sulfate (SDS) and Triton X100 were tested separately. Statistical models were developed for the effects on the ADI activity of the following factors: the concentration of the surfactant, the length of the treatment period and the concentration of the cells. For all surfactants, the concentration of cells was the most significant factor in influencing permeabilization. All permeabilization treatments used mild conditions (pH 7, 37 °C). The permeabilized cells were immobilized in alginate beads for the biotransformation of arginine to citrulline. The optimal conditions for immobilization and biotransformation were as follows: 2% (w/v, g/100 mL) sodium alginate, 100 g/L of treated cells, 40 mM arginine, pH 6.0, a temperature of 35 °C and an agitation speed of 150 rpm. The immobilized biocatalyst retained nearly 90% of its initial activity after nine cycles of repeated use in batch operations. In contrast, the freely suspended cells were barely active after the second use cycle.     

Immobilization of rice (Oryza sativa L.) callus in polyurethane foam using a turbine blade reactor

A turbine blade reactor (TBR) was employed to cultivate rice calli immobilized in polyurethane foam as a support. In the bioreactor, rice callus could be immobilized quickly in a 3 mm cube of the support, and then attached to the stainless mesh cylinder set at the center of the bioreactor. For improving the immobilization ratio of rice callus in the bioreactor, the optimum support volume and bioreactor operation and modification were investigated. The support volume had a pronounced effect on the immobilization ratio of rice callus, and the maximum volume was found to be 60 ml. By repeating a periodic operation three times (agitating at 300 rpm for 5 min and then 50 rpm for 2 min, and then 200 rpm of constant agitation speed during the remaining time), rice calli were uniformly entrapped in almost all supports and the immobilization ratio was improved as compared with that using a constant bioreactor operation at 200 rpm. When the inoculum concentration of rice callus was increased, the callus concentration after 7-day culture increased, but the immobilization ratio decreased. To improve the immobilization efficiency further at high cell concentration, the TBR was modified by setting an air sparger inside the stainless mesh cylinder. In the modified TBR, floating of the support by attached air bubbles was avoided, and the immobilization ratio increased further and reached 86.3% when we increased the support volume to 90 ml under the periodic bioreactor operation on a daily basis. The regeneration frequency of immobilized callus was increased by periodic operation and modification of the bioreactor.     

Laccase immobilization on mesostructured cellular foams affords preparations with ultra high activity

Extracellular laccase produced by the wood-rotting fungus Cerrena unicolor was immobilized covalently on the mesostructured siliceous cellular foams (MCFs) functionalised using various organosilanes with amine and glycidyl groups. The experiments indicated that laccase bound via glutaraldehyde to MCFs modified using 2-aminoethyl-3-aminopropyltrimethoxysilane remains very active. In the best biocatalyst activity was about 42,700 U mL^?1 carrier (66,800 U mg^?1 bound protein), and hence significantly higher than ever reported before. Optimisation of the immobilization procedure with respect to protein concentration, pH of coupling mixture and the enzyme purity afforded the biocatalyst with activity of about 90,980 U mL^?1. For the best preparation, thermal- and pH-stability, and activity profiles were determined. Experiments carried out in a batch reactor showed that k_cat/K_m for immobilized enzyme (0.88 min^?1 μM^?1) was acceptable lower than the value obtained for the native enzyme (2.19 min^?1 μM^?1). Finally, potentials of the catalysts were tested in the decolourisation of indigo carmine without redox-mediators. Seven consecutive runs with the catalysts separated by microfiltration proved that adsorption of the dye onto the carrier and enzymatic oxidation contribute to the efficient decolourisation without loss of immobilized enzyme activity.     

Polyaniline grafted polyacylonitrile conductive composite fibers for reversible immobilization of enzymes: Stability and catalytic properties of invertase

Polyacylonitrile fibers (PAN) surfaces were modified with chemical polymerization of conductive polyaniline (PANI) in the presence of potassium dichromate as an oxidizing agent. The effect of aniline concentration on the grafting efficiency and on the electrical surface resistance of PAN/PANI composite fibers was investigated. The surface resistance of the conductive composite fibers in this work was found to be between 8.0 and 0.5 kΩ/cm. As the amount of grafted PANI increased on the PAN fibers the electrical resistance of composite fibers decreased. The PAN/PANI composite fibers were characterized by SEM and FTIR studies. Composite PAN/PANI fibers were used for reversible immobilization of invertase. The immobilization efficiency and the activity of the immobilized invertase (from 1.0 mg/mL invertase solution at pH 5.5) were increased with increasing PANI contents of the composite fibers. The maximum amount of immobilized enzyme onto composite fibers containing 2.0% PANI was about 76.6 mg/g. The optimum pH for the free enzyme was observed at 5.0. On the other hand, immobilized invertase yielded a broad optimum pH profile between pH 5.0 and 7.0. Immobilized invertase exhibited 83% of its original activity even after two months storage at 4 °C while the free enzyme showed only 7% of its initial activity.     

Continuous production of oligoglucuronans by immobilized glucuronan lyase

A glucuronan lyase was incubated with sepharose matrices pre-activated with N-hydroxysuccinimide (NHS), cyanogen bromide (CNBr) or epoxy. The CNBr- and NHS-activated gels showed satisfactory immobilization yields whereas no enzyme could be immobilized using the epoxy coupling group. Glucuronan lyase immobilized on CNBr-gel ensured rapid conversion of several glucuronans into oligomers with an enzymatic activity identical to that of the free enzyme. As classically observed when using free enzymes, the acetylation degree of glucuronan limited enzyme activity. Nevertheless, this immobilized system made it easier to obtain accurately oligomers with different polymerization degrees, notably in modifying the glucuronans residence times in column. Thus oligoglucuronan pools with polymerization degrees between 2 and 25 could be obtained with a productivity ranging from 120 mg h^?1 to 1.2 g h^?1 using 0.9 ml of chromatographic gel with immobilized glucuronan lyase. This methodology opens the way to continuous and large oligoglucuronan productions.     

Decolorization of azo dye by immobilized Pseudomonas luteola entrapped in alginate–silicate sol–gel beads

Pseudomonas luteola was immobilized by entrapment in alginate–silicate sol–gel beads for decolorization of the azo dye, Reactive Red 22. The influences of biomass loading and operating conditions on specific decolorization rate and dye removal efficiency were studied in details. The immobilized cells were found to be less sensitive to changes in agitation rates (dissolved oxygen levels) and pH values. Michaelis–Menten kinetics could be used to describe the decolorization kinetics with the kinetic parameters being 36.5 mg g⁻¹ h⁻¹, 300.1 mg l⁻¹ and 18.2 mg g⁻¹ h⁻¹, 449.8 mg l⁻¹ for free and immobilized cells, respectively. After five repeated batch cycles, the decolorization rate of the free cells decreased by nearly 54%, while immobilized cells still retained 82% of their original activity. The immobilized cells exhibited better thermal stability during storage and reaction when compared with free cells. From SEM observation, a dense silicate gel layer was found to surround the macroporous alginate–silicate core, which resulted in much improved mechanical stability over that of alginate beads when tested under shaking conditions. Alginate–silicate matrices appeared to be the best matrix for immobilization of P. luteola in decolorization of Reactive Red 22 when compared with previous results using synthetic or natural polymer matrices.