Improved catalytic performance of GA cross-linking treated Rhizopus oryzae IFO 4697 whole cell for biodiesel production

Whole cell-mediated methanolysis of renewable oils for biodiesel production has drawn much attention in recent years since it can avoid the complex procedures of isolation, purification and immobilization required for the preparation of immobilized lipase. It has been demonstrated that Rhizopus oryzae IFO 4697 whole cell could catalyze the methanolysis of renewable oils for biodiesel production effectively and glutaraldehyde (GA) cross-linking treatment on whole cell catalyst could improve its stability in the repeated uses. The catalytic performance of cells with GA cross-linking treatment was studied systematically in this paper. The results showed that the treated cells expressed higher methanol tolerance, and high catalytic activity could be maintained with higher ratio of methanol to oil; the operational stability of whole cell catalyst and methanol utilization rate were also considered in optimization of methanol addition strategy. A novel methanol addition strategy was proposed, with which the reaction time could be shortened significantly and a biodiesel yield of 94.1% could be obtained within 24 h reaction; it was also found that with this methanol addition strategy, GA cross-linked whole cell expressed rather good operational stability; the reason for stability improvement was also investigated and should be attributed to less lipase leakage.     

Rhizopus oryzae IFO 4697 whole cell catalyzed methanolysis of crude and acidified rapeseed oils for biodiesel production in tert-butanol system

Whole cell Rhizopus oryzae (R. oryzae) IFO4697 immobilized within biomass support particles (BSPs) was used as catalyst for biodiesel production in tert-butanol, in which the stability of the catalyst could be enhanced significantly. Different feedstocks (refined, crude and acidified rapeseed oils) were adopted further for biodiesel production in tert-butanol system and it was found that when acidified rapeseed oil was used as feedstocks, the reaction rate and final methyl ester (ME) yield were significantly higher than that of refined and crude rapeseed oil. Major differences among the aforementioned oils were found to be the contents of free fatty acid (FFA), water and phospholipids, which showed varied influences on whole cell mediated methanolysis for biodiesel production. The reaction rate increased with the increase of free fatty acid content in oils; water content had varied influence on reaction rate and biodiesel yield; using adsorbent to remove excessive water could increase biodiesel yield significantly (from 73 to 84%); it was also found interestingly that phospholipids contained in oils could increase the reaction rate to a certain extent.     

Effect of diet on hyperthermia-induced cell lethality and prostaglandin release.

Hyperthermia-induced cell lethality is thought to be mediated through injury to the cell membrane. Membrane perturbation results in the release of prostaglandins (PG) and leukotrienes (LT). These compounds are potent biological mediators and may modify the tumor microenvironment and therapeutic efficacy. Membrane composition and PG/LT release are influenced by the dietary fatty acids. The relationship between these variables and response to hyperthermia was examined in vitro using murine P388 leukemia cells grown as an ascites in mice provided either saturated fatty acid diet (SFA; 16% beef tallow) or unsaturated fatty acid diet (UFA; 16% safflower oil). Cells were harvested and exposed in vitro to either 37 degrees C or 43.5 degrees C for periods up to 2 hours. Hyperthermic exposure for 2 hours resulted in 40% cell lethality in SFA cells and 55% in UFA cells. The phospholipid and total cholesterol content was higher (33% and 50% respectively) in the UFA versus the SFA cells. Hyperthermia produced a six-fold increase in prostaglandin E2 PGE2 release by SFA cells and a 4.5-fold increase by UFA cells. No LTC4 was detected. Alteration of dietary fat affects cell lethality and PG release following hyperthermic treatment. The increase in phospholipid and cholesterol content of UFA cells may be a response to reduced membrane fluidity.     

Study on the effect of cultivation parameters and pretreatment on Rhizopus oryzae cell-catalyzed transesterification of vegetable oils for biodiesel production

Enzymatic methanolysis of vegetable oils for biodiesel production has become a hot point recently, in which study on whole cell as catalyst is an important field. In this paper, whole cell (Rhizopus oryzae IFO 4697) was adopted directly as biocatalyst for biodiesel production. Effects of carbon source on cell growth and whole cell-catalyzed methanolysis of vegetable oils for biodiesel production were studied. The results showed that different oils contained in the cultivation medium had varied effects on the whole cell-catalyzed methanolysis of oils; with some specified oil as the carbon source for cell cultivation, those cells expressed higher catalytic activity in catalyzing the transesterification of the same oil for biodiesel production. The initial reaction rate was increased notably (204%) with oil pretreatment on the cells before catalyzing the reaction, which was possibly due to the improved mass transferring of substrates. Under the optimized conditions, the maximum methyl ester yield could reach 86%.     

Study on the effect of cultivation parameters and pretreatment on Rhizopus oryzae cell-catalyzed transesterification of vegetable oils for biodiesel production

Enzymatic methanolysis of vegetable oils for biodiesel production has become a hot point recently, in which study on whole cell as catalyst is an important field. In this paper, whole cell (Rhizopus oryzae IFO 4697) was adopted directly as biocatalyst for biodiesel production. Effects of carbon source on cell growth and whole cell-catalyzed methanolysis of vegetable oils for biodiesel production were studied. The results showed that different oils contained in the cultivation medium had varied effects on the whole cell-catalyzed methanolysis of oils; with some specified oil as the carbon source for cell cultivation, those cells expressed higher catalytic activity in catalyzing the transesterification of the same oil for biodiesel production. The initial reaction rate was increased notably (204%) with oil pretreatment on the cells before catalyzing the reaction, which was possibly due to the improved mass transferring of substrates. Under the optimized conditions, the maximum methyl ester yield could reach 86%.     

Effect of saturated, omega-3 and omega-6 polyunsaturated fatty acids on myocardial infarction

Dietary fatty acids have cholesterol lowering, antiatherogenic, and antiarrhythmic properties that decrease the risk of myocardial infarction (MI). This study was designed to study the effects of various oils rich in either polyunsaturated (omega-3 or omega-6) fatty acids (PUFA) or saturated fatty acids (SFA) on the severity of experimentally induced MI. Male albino Sprague-Dawley rats (100-150 g; n = 20) were fed diets enriched with fish oil (omega-3 PUFA), peanut oil (omega-6 PUFA), or coconut oil (SFA) for 60 days. Experimental MI was induced with isoproterenol. Mortality rates; serum enzymes aspartate amino transferase; alanine amino transferase; creatine phosphokinase (CPK); lipid profiles in serum, myocardium, and aorta; peroxide levels in heart and aorta; activities of catalase and superoxide dismutase; and levels of glutathione were measured. The results demonstrated that mortality rate, CPK levels, myocardial lipid peroxides, and glutathione levels were decreased in the omega-3 PUFA treated group. Maximum increase in parameters indicative of myocardial damage was seen in the coconut oil group. These findings suggest that dietary omega-3 PUFA offers maximum protection in experimentally induced MI in comparison to omega-6 PUFA and SFA enriched diets. SFA was found to have the least protective effect.     

The influence of fatty acids on model cholesterol/phospholipid membranes

The aim of this work was to verify the influence of the saturated (SFA) (stearic acid) and the unsaturated (UFA) (oleic and alpha-linolenic) fatty acids on model cholesterol/phospholipid membranes. The experiments were based on the Langmuir monolayer technique. Cholesterol and phospholipid were mixed in the molar ratio that corresponds to the proportion of these lipids in the majority of natural human membranes. Into the binary cholesterol/phospholipid monolayers, various amounts of fatty acids were incorporated. Our investigations were based on the analysis of the interactions between molecules in ternary (cholesterol/phospholipids/fatty acid) mixtures, however, also binary (cholesterol/fatty acid and phospholipids/fatty acid) mixed system were examined. It was concluded that the influence of the fatty acids on model cholesterol/phospholipid membrane is closely connected with the shape of the fatty acid molecule, resulting from the saturation degree of the hydrocarbon chain. It was found that the saturated fatty acid makes the model membrane more rigid, while the presence of unsaturated fatty acid increases its fluidity. The increasing amount of stearic acid gradually destabilizes model membrane, however, this effect is the weakest at low content of SFA in the mixed monolayer. Unsaturated fatty acids in a small proportion make the membrane thermodynamically more stable, while higher content of UFA decreases membrane stability. This explains low proportion of the free fatty acids to other lipids in natural membrane.     

Efficient production of biodiesel from high free fatty acid-containing waste oils using various carbohydrate-derived solid acid catalysts

In the present study, such carbohydrate-derived catalysts have been prepared from various carbohydrates such as d-glucose, sucrose, cellulose and starch. The catalytic and textural properties of the prepared catalysts have been investigated in detail and it was found that the starch-derived catalyst had the best catalytic performance. The carbohydrate-derived catalysts exhibited substantially higher catalytic activities for both esterification and transesterification compared to the two typical solid acid catalysts (sulphated zirconia and Niobic acid), and gave markedly enhanced yield of methyl esters in converting waste cooking oils containing 27.8wt% high free fatty acids (FFAs) to biodiesel. In addition, under the optimized reaction conditions, the starch-derived catalyst retained a remarkably high proportion (about 93%) of its original catalytic activity even after 50 cycles of successive re-use and thus displayed very excellent operational stability. Our results clearly indicate that the carbohydrate-derived catalysts, especially the starch-derived catalyst, are highly effective, recyclable, eco-friendly and promising solid acid catalysts that are highly suited to the production of biodiesel from waste oils containing high FFAs.     

Omega-3 production by fish oil hydrolysis using a lipase from Burkholderia gladioli BRM58833 immobilized and stabilized by post-immobilization techniques

Immobilization of lipase from Burkholderia gladioli BRM58833 on octyl sepharose (OCT) resulted in catalysts with higher activity and stability. Following, strategies were studied to further stabilize and secure the enzyme to the support using functionalized polymers, like polyethylenimine (PEI) and aldehyde-dextran (DEXa), to cover the catalyst with layers at different combinations. Alternatively, the construction of a bifunctional layer was studied using methoxypolyethylene glycol amine (NH 2 -PEG) and glycine. The catalyst OCT-PEI-DEXa was the most thermostable, with a 263.8-fold increase in stability when compared to the control condition. When evaluated under alkaline conditions, OCT-DEXa-PEG 10 /Gly was the most stable, reaching stability 70.1 times greater than the control condition. Proportionally, the stabilization obtained for B. gladioli BRM58833 lipase was superior to that obtained for the commercial B. cepacia lipase. Preliminary results in the hydrolysis of fish oil demonstrated the potential of the coating technique with bifunctional polymers, resulting in a stable catalyst with greater catalytic capacity for the production of omega-3 PUFAs. According to the results obtained, it is possible to modulate B. gladioli BRM58833 lipase properties like stability and catalytic activity for enrichment of omega-3 fatty acids.     

Lipase-catalyzed biodiesel production with methyl acetate as acyl acceptor

Biodiesel is an alternative diesel fuel made from renewable biological resources. During the process of biodiesel production, lipase-catalyzed transesterification is a crucial step. However, current techniques using methanol as acyl acceptor have lower enzymatic activity; this limits the application of such techniques in large-scale biodiesel production. Furthermore, the lipid feedstock of currently available techniques is limited. In this paper, the technique of lipase-catalyzed transesterification of five different oils for biodiesel production with methyl acetate as acyl acceptor was investigated, and the transesterification reaction conditions were optimized. The operation stability of lipase under the obtained optimal conditions was further examined. The results showed that under optimal transesterification conditions, both plant oils and animal fats led to high yields of methyl ester: cotton-seed oil, 98%; rapeseed oil, 95%; soybean oil, 91%; tea-seed oil, 92%; and lard, 95%. Crude and refined cottonseed oil or lard made no significant difference in yields of methyl ester. No loss of enzymatic activity was detected for lipase after being repeatedly used for 40 cycles (ca. 800 h), which indicates that the operational stability of lipase was fairly good under these conditions. Our results suggest that cotton-seed oil, rape-seed oil and lard might substitute soybean oil as suitable lipid feedstock for biodiesel production. Our results also show that our technique is fit for various lipid feedstocks both from plants and animals, and presents a very promising way for the large-scale biodiesel production.     

Membrane polyunsaturated fatty acids and lithium-sodium countertransport in human erythrocytes

Two groups of individuals, 26 normotensive normolipemic and 37 normotensive hyperlipemic, all without family history of hypertension have been selected in attempt to demonstrate whether Li-Na countertransport of erythrocytes is influenced by plasma and membrane lipid composition. The maximal rate of Li-Na countertransport was elevated in hyperlipemics (0.344 +/- 0.168 vs 0.220 +/- 0.074 mmol/l erythrocytes/h). This difference is highly significant. Hyperlipemics had different composition of membrane lipids than normals. The most important variations were: increase of palmitic, palmitoleic and total saturated fatty acids (SFA) as well as increase of cholesterol/phospholipids ratio (C/PL); in contrast, hyperlipemics had a reduced amount of linoleic acid and total unsaturated fatty acids (UFA) as well as total polyunsaturated fatty acids (PUFA). Consequently, UFA/SFA and PUFA/SFA ratios were lower than in normals. Li-Na countertransport was negatively correlated with the amount of PUFA (P less than 0.02), whereas it was positively correlated with the following parameters: oleic/linoleic ratio (p less than 0.02), monounsaturated fatty acids/polyunsaturated fatty acids ratio (p less than 0.03) as well as with the SFA + monounsaturated fatty acid/PUFA ratio (p less than 0.03). These findings suggest that the V max of Li-Na countertransport in erythrocytes is influenced by the lipid composition of the membrane.     

Synthesis of glycerides containing n-3 fatty acids and conjugated linoleic acid by solvent-free acidolysis of fish oil

Menhaden oil, a rich source of n-3 fatty acids, was interesterified with conjugated linoleic acid (CLA) in a reaction medium composed solely of substrates and either free or immobilized commercial lipase preparations. Of five lipases tested, an immobilized preparation from Mucor miehei provided the fastest rate of incorporation of CLA into fish oil acylglycerols; however, and as observed with most of the lipases utilized, a significant proportion of the n-3 fatty acid residues were liberated in the process. A soluble lipase from Candida rugosa converted free CLA to acylglycerol residues while leaving the n-3 fatty acid residues virtually untouched. Even though the reaction rate was slower for this enzyme than for the other four lipase preparations, the specificity of the free C. rugosa lipase gives it the greatest potential for commercial use in preparing fish oils enriched in CLA residues but still retaining their original n-3 fatty acid residues.     

酚酮类对树干毕赤酵母乙醇发酵及脂肪酸组成的影响

木质素降解产物对微生物产生的抑制作用,是燃料乙醇生物炼制的主要瓶颈之一。本文以树干毕赤酵母为发酵菌株,研究木质素降解产物中3种酚酮类(4-羟基苯乙酮、4-羟基-3-甲氧基苯乙酮、4-羟基-3,5-二甲氧基苯乙酮)对其木糖乙醇发酵及酵母细胞脂肪酸组成的影响。采用高效液相色谱(HPLC)和气相色谱-质谱联用(GC/MS)技术对乙醇发酵性能和酵母细胞脂肪酸组成进行分析。研究结果表明,酚酮类物质对乙醇发酵呈现抑制作用且其分子量越低抑制作用越明显,当4-羟基苯乙酮浓度为1.50 g/L时,发酵24 h的木糖利用率、乙醇得率和乙醇浓度分别下降了42.47%、5.30%和9.76 g/L;培养基中存在酚酮类物质时,酵母细胞中的不饱和脂肪酸的比例上升,添加1.50 g/L的3种酚酮类物质后,树干毕赤酵母细胞不饱和脂肪酸和饱和脂肪酸的比例从原来的2.58分别上升到3.03、3.06和3.61,酵母细胞膜的流动性随之上升,不稳定性提高。因此,酚酮类物质能够降低酵母生长、提高不饱和脂肪酸的比例以及降低乙醇发酵能力,有效降低或去除木质素降解产物含量是提高木质纤维原料生物炼制的关键。     

Rhodococcus UKMP-5M, an endogenous lipase producing actinomycete from Peninsular Malaysia

Escalation in food industries unctuous wastes has led to serious anthropogenic problems to the environment. Parallel to “green strategy”, growing awareness in biological treatment emphasizes efficacy of enzymatic technology for bioremediation. Pertinently, researchers are in search for new lipase-lipid interaction for improved outcome. Rhodococcus species have documented inadequate evidences on lipase enzyme production. Consequent assessments on Rhodococcus isolates from Peninsular Malaysia have identified twelve promising strains as lipase producer. Interestingly, apart from usual lipolytic behaviour, Rhodococcus sp. exhibited significant level of lipase endogenously, while cryogenic grinding method effectively ruptured the cell. An isolate from petroleum-contaminated site, namely Rhodococcus UKMP-5M, projected the highest level of lipase specificity and has further been optimized. It was found out that the best specificity was apparent in acidic condition (pH 5) with 6% inoculum at 30°C for 72 hours of incubation. Due to high level of mycolic cell-surfactant developed in triacylglycerol supplements, cell lysis was employed with Triton X-100 detergent solubilisation. As a result, oil blend composed of various carbon-chain length fatty acids (composite 2) induces enzyme production extensively. Remarkably, R. UKMP-5M found to cater enzyme production without aid of inducer by nature, but additional carbon source like glucose represses lipase production. Further ability for biological treatment was revealed when the optimized R. UKMP-5M whole cell degraded waste cooking oil significantly by solubilizing fatty acids and commencing conversion into biomass. These qualities resemble practical new lipid-lipase biological lipid rich on-site treatment.     

Use of re-esterified palm oils,differing in their acylglycerol structure,in fattening pig diets

Re-esterified oils are new fat sources obtained from the chemical esterification of acid oils with glycerol (both economically interesting by-products from oil refining and biodiesel industries, respectively). The different fatty acid (FA) positional distribution and acylglycerol composition of re-esterified oils may enhance the apparent absorption of saturated fatty acids (SFA) and, therefore, their overall nutritive value, which might lead to an increased deposition of SFA. The aim of the present study was to investigate the potential use of re-esterified palm oils, in comparison with their corresponding acid and native oils in fattening pig diets, studying their effects on fatty acid apparent absorption, acylglycerol and free fatty acid (FFA) composition of feces, growth performance, carcass-fat depots and fatty acid composition of backfat. Seventy-two crossbred boars and gilts (average weight of 24.7±2.55 kg) were blocked by initial BW (nine blocks of BW for each gender), housed in adjacent individual boxes, and fed one of the four dietary treatments, which were the result of a basal diet supplemented with 4% (as-fed basis) of native palm oil (PN), acid palm oil (PA), re-esterified palm oil low in mono- and diacylglycerols (PEL), or re-esterified palm oil high in mono- and diacylglycerols (PEH). Regarding results from the digestibility balance, PA and PN showed similar apparent absorption coefficients (P>0.05), despite the high, FFA content of the former. However, re-esterified palm oils (both PEL and PEH) showed a higher apparent absorption of total FA than did their corresponding native and acid oils (P<0.001), mainly due to the increased apparent absorption of SFA (P<0.001). This resulted in a greater feed efficiency and an increased deposition of SFA in backfat of pigs fed PEH, when compared with those fed PA (P<0.05), although no differences were found for carcass-fat depots (P>0.05). We conclude that re-esterified oils are interesting fat sources to be considered in fattening pigs.     

Production of structured triacylglycerols (STAG) rich in docosahexaenoic acid (DHA) in position 2 by acidolysis of tuna oil catalyzed by lipases

This work deals with the production of structured triacylglycerols (STAG) with caprylic acid (CA) located in positions 1 and 3 of the molecule of glycerol and docosahexaenoic acid (DHA) in position 2, by acidolysis of tuna oil and CA, catalyzed by several lipases. To this end several lipases and immobilization supports were tested with the aim of avoiding the acyl-migration observed in previous works. The determination of the best catalyst (i.e. the lipase and the immobilization support as a whole) was carried out by experiments of acidolysis of cod liver oil and CA in a bath reactor. The best results were obtained with the lipases from Rhizopus oryzae (Lipase D) and Rhizopus delemar (Lipase Rd), immobilized on Accurel MP1000 (a microporous polypropylene) with a lipase/support ratio 1:1.5 (w/w). The activity of these immobilized lipases was stable for a minimum of 5 days in the operational conditions (up to 40 °C).Lipase Rd was selected for the next step in which it was immobilized on Acurrel MP1000 to obtain STAG enriched in DHA by acidolysis of tuna oil (20% DHA) with CA. The experiments were carried out by recirculating the reaction mixture through an immobilized lipase packed bed reactor at different substrate/hexane ratios, as well as in absence of solvent. In the latter case, STAG with 51% CA and 13% DHA were obtained at 73 h. This result indicates that with this catalyst an acceptable reaction rate was attained in absence of solvent. A structural analysis by the pancreatic lipase method carried out to STAG with 45% CA and 16% DHA indicated that 91% of the CA incorporated is located in positions 1 and 3, and that 51% of the DHA is located in position 2 (MLM structure). This position is also rich in palmitic, eicosapentaenoic and oleic acids.After the acidolysis reaction a mixture of STAG and free fatty acids was obtained. The recovery of STAG from this reaction mixture is difficult because of the high content of free fatty acids. A separation method based on the neutralization of the free fatty acids with a KOH hydroalcoholic solution has been developed. By this procedure pure (100%) STAG were obtained with a recovery yield of 80%.     

Enzyme catalysed production of vegetable oils containing omega-3 polyunsaturated fatty acid

Summary The application of enzymatic interesterification for production of vegetable oils containing omega-3 polyunsaturated fatty acids was investigated. Six veteable oils were used as substrates, together with omega-3 polyunsaturated fatty acid, and reactions were catalysed by immobilized Mucor miehei lipase in organic solvent. The degree of incorporation of eicosapentaenoic acid and docosahexaenoic acid into corn oil, sunflower oil, peanut oil, olive oil and soybean oil were 17.71, 17.59, 16.79, 14.89, 13.91 and 10.48%, respectively, after a 12 h incubation period.     

Rose hip (Rosa canina L.) oil obtained from waste hip seeds by different extraction methods

From the rose hip seed, which is generally a waste material, valuable oil can be obtained for medicinal use. Various extraction methods have been compared: traditional solvent extraction with ultrasound-, microwave-, sub- and supercritical fluid extraction (SFE). Unsaturated fatty acid (UFA: oleic-, linoleic- and linolenic acid; 16.25-22.11%, 35.94-54.75%, 20.29-26.48%) and polyunsaturated fatty acid (PUFA:linoleic- and linolenic acid) content were over 90% and 60% in the recovered oils. The oils contained different amounts of metals. The concentration of some metals, particularly iron in microwave oil (27.11 microg g(-1)) is undesirable from the aspect of stability. By traditional solvent extraction, oil was obtained in 4.85 wt/wt%. Subcritical FE appeared to be the best method for the recovery of rose hip oil with highest oil yield (6.68 wt/wt%), carotene- (145.3 microg g(-1)) and linoleic acid content (54.75%). Supercritical FE without organic solvent is suitable for mild recovery of oil. The oil was rich in UFA and PUFA (92.7% and 76.25%) and contained the lowest amount of carotene and pheophytin (36.3 and 45.8 microg g(-1)). Oil yield in most new extraction methods (microwave extraction, super- and subcritical FE) was higher than in the case of traditional Soxhlet extraction. The main benefit of supercritical FE with CO2 is the solvent free oil while in the case of other extractions evaporation of the solvent is needed. Although the content of bioactive compounds in oils was different, all oils may be appropriate for medicinal use.     

Solvent-free glycerolysis of palm and palm kernel oils catalyzed by commercial 1,3-specific lipase from Humicola lanuginosa and composition of glycerolysis products

Glycerolysis of palm and palm kernel oils were conducted using a commercial 1,3-specific lipase from Humicola lanuginosa (trade name: SP 398) as catalyst (500 units lipase g^–1 oil) at 40°C and oil:glycerol (1:2 mol mol^–1) in a solvent-free system. After 24 h, the glycerolysis products of palm and palm kernel oils consisted of 23% triacylglycerols, 18% monoacylglycerols, 38% diacylglycerols and 18% triacylglycerols, 31% monoacylglycerols, 42% diacylglycerols, respectively. The monoacylglycerol fraction of the glycerolysis product of palm oil was enriched in oleic acid. Palmitic acid content of the monoacylglycerol fraction of the same product was less than that of the original oil. Under the same conditions, monacylglycerol fraction of the palm kernel oil glycerolysis product was enriched in palmitic, stearic and oleic acids.