Differences in colonisation of five marine bacteria on two types of glass surfaces

The retention patterns of five taxonomically different marine bacteria after attachment on two types of glass surfaces, as-received and chemically etched, have been investigated. Contact angle measurements, atomic force microscopy (AFM), scanning electron microscopy (SEM), confocal laser scanning microscopy (CLSM), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectrometry (XPS) were employed to investigate the impact of nanometer scale surface roughness on bacterial attachment. Chemical modification of glass surfaces resulted in a ～1 nm decrease in the average surface roughness (R _a) and the root-mean-squared roughness (R_q ) and in a ～8 nm decrease in the surface height and the peak-to-peak (R _max) and the 10-point average roughness (R_z ). The study revealed amplified bacterial attachment on the chemically etched, nano-smoother glass surfaces. This was a consistent response, notwithstanding the taxonomic affiliation of the selected bacteria. Enhanced bacterial attachment was accompanied by elevated levels of secreted extracellular polymeric substances (EPS). An expected correlation between cell surface wettability and the density of the bacterial attachment on both types of glass surfaces was also reported, while no correlation could be established between cell surface charge and the bacterial retention pattern.     

Barnacle settlement and the adhesion of protein and diatom microfouling to xerogel films with varying surface energy and water wettability

Previous work has shown that organosilica-based xerogels have the potential to control biofouling. In this study, modifications of chemistry were investigated with respect to their resistance to marine slimes and to settlement of barnacle cyprids. Adhesion force measurements of bovine serum albumin (BSA)-coated atomic force microscopy (AFM) tips to xerogel surfaces prepared from aminopropylsilyl-, fluorocarbonsilyl-, and hydrocarbonsilyl-containing precursors, indicated that adhesion was significantly less on the xerogel surfaces in comparison to a poly(dimethylsiloxane) elastomer (PDMSE) standard. The strength of adhesion of BSA on the xerogels was highest on surfaces with the highest and the lowest critical surface tensions, γ_C and surface energies, γ_S, and duplicated the ‘Baier curve’. The attachment to and removal of cells of the diatom Navicula perminuta from a similar series of xerogel surfaces were examined. Initial attachment of cells was comparable on all of the xerogel surfaces, but the percentage removal of attached cells by hydrodynamic shear stress increased with γ_C and increased wettability as measured by the static water contact angle, θ_Ws, of the xerogel surfaces. The percentage removal of cells of Navicula was linearly correlated with both properties (R ² = 0.74 for percentage removal as a function of θ_Ws and R ² = 0.69 for percentage removal as a function of γ_C). Several of the aminopropylsilyl-containing xerogels showed significantly greater removal of Navicula compared to a PDMSE standard. Cypris larvae of the barnacle B. amphitrite showed preferred settlement on hydrophilic/higher energy surfaces. Settlement was linearly correlated with θ_Ws (R ² = 0.84) and γ_C (R ² = 0.84). Hydrophilic xerogels should prove useful as coatings for boats in regions where fouling is dominated by microfouling (protein and diatom slimes).     

Synthesis,characterization and in vitro activity of a surface-attached antimicrobial cationic peptide

Infection associated with implanted biomaterials is common and costly and such infections are extremely resistant to antibiotics and host defenses. Consequently, there is a need to develop surfaces which resist bacterial adhesion and colonization. The broad spectrum synthetic cationic peptide melimine has been covalently linked to a surface via two azide linkers, 4-azidobenzoic acid (ABA) or 4-fluoro-3-nitrophenyl azide (FNA), and the resulting surfaces characterized by X-ray photoelectron spectroscopy and contact angle measurements. The quantity of bound peptide was estimated by a modified Bradford assay. The antimicrobial efficacy of the two melimine-modified surfaces against Pseudomonas aeruginosa and Staphylococcus aureus was compared by scanning electron microscopy (SEM) and fluorescence microscopy. Attachment of melimine via ABA gave an approximately 4-fold greater quantity of melimine bound to the surface than attachment via FNA. Surfaces melimine-modified by either attachment strategy showed significantly reduced bacterial adhesion for both strains of bacteria. P. aeruginosa exposed to ABA–melimine and FNA–melimine surfaces showed marked changes in cell morphology when observed by SEM and a reduction of approximately 15-fold (p < 0.001) in the numbers of adherent bacteria compared to controls. For the ABA–melimine surface there was a 33% increase in cells showing damaged membranes (p = 0.0016) while for FNA–melimine there was no significant difference. For S. aureus there were reductions in bacterial adhesion of approximately 40-fold (p < 0.0001) and 5-fold (p = 0.008) for surfaces modified with melimine via ABA or FNA, respectively. There was an increase in cells showing damaged membranes on ABA–melimine surfaces of approximately 87% (p = 0.001) compared to controls, while for FNA–melimine there was no significant difference observed. The data presented in this study show that melimine has excellent potential for development as a broad spectrum antimicrobial coating for biomaterial surfaces. Further, it was observed that the efficacy of antimicrobial activity is related to the method of attachment.     

Effects of DNP on the cell surface properties of marine bacteria and its implication for adhesion to surfaces

Abstract

The effect of 2, 4-dinitrophenol (DNP) on the extracelluar polysaccharides (EPS), cell surface charge, and the hydrophobicity of six marine bacterial cultures was studied, and its influence on attachment of these bacteria to glass and polystyrene was evaluated. DNP treatment did not influence cell surface charge and EPS production, but had a significant effect on hydrophobicity of both hydrophilic (p = 0.05) and hydrophobic (p = 0.01) cultures. Significant reduction in the attachment of all the six cultures to glass (p = 0.02) and polystyrene (p = 0.03) was observed after DNP treatment. Moreover, hydrophobicity but not the cell surface charge or EPS production influenced bacterial cell attachment to glass and polystyrene. From this study, it was evident that DNP treatment influenced bacterial cell surface hydrophobicity, which in turn, reduced bacterial adhesion to surfaces.     

Testing attachment point theory: diatom attachment on microtextured polyimide biomimics

Abstract

This paper explores diatom attachment to a range of laser etched polyimide surfaces to directly test ‘attachment point theory’. Static bioassays were conducted on microtextured polyimide surfaces using four diatom species, Fallacia carpentariae, Nitzschia cf. paleacea, Amphora sp. and Navicula jeffreyi with cell sizes ranging from 1 – 14 μm. The microtextured polyimides were modelled from natural fouling resistant bivalve surfaces and had wavelengths above, below and at the same scale as the diatom cell sizes. Diatoms attached in significantly higher numbers to treatments where the numbers of attachment points was highest. The lowest diatom attachment occurred where cells were slightly larger than the microtexture wavelength, resulting in only two theoretical points of attachment. The results support attachment point theory and highlight the need to address larval/cell size in relation to the number of attachment points on a surface. Further studies examining a range of microtexture scales are needed to apply attachment point theory to a suite of fouling organisms and to develop structured surfaces to control the attachment and development of fouling communities.     

Capillary Distribution in the Lateral Muscle of Axolotl (Ambystoma mexicanum Shaw)

The vascular supply of red, intermediate and white fibres in the axial muscle of axolotl (Ambystoma mexicanum Shaw) was visualized with Indian ink-injections and quantified with morphometrical methods on semithin sections. Red fibres were surrounded by 1.4 ± 0.6 capillaries (mean + SD), the intermediate fibres by 1.2 ± 0.9 capillaries and white fibres by 0.3 ± 0.6 capillaries. The mean vascularized surface area per unit volume of fibre was 0.0159, and 0.0068 and 0.0007 (μm²/μm³) for red, intermediate and white fibres, respectively. A unit volume of mitochondria within each type of fibre was supplied by 0.15, 0.17 and 0.08 μm² vascularized surface for red, intermediate and white fibres, respectively. This indicates that there exist a good balance between oxygen demand represented by mitochondrial content and oxygen supply represented by the vascularized surface.     

Impact of wastewater fouling on contact angle

Capillary dependent systems are highly influenced by surface fouling and may degrade as material surface properties change. In anticipation of a spacecraft microgravity fluids management system exposed to highly variable wetting conditions, the impact of urine wastewater fouling on capillary contact angle was examined. The results indicate that, in general, surface fouling can decrease the contact angle when crystalline structures or biofilms form. Small crystalline growth on the order of 10 μm can lower advancing contact angles θ_adv by approximately 30°, while biofilm growth can lower it by approximately 15°. Vacuum drying of fouled surfaces increased θ_adv by about 8°, and defects greater in height than 5% of the capillary length increased θ_adv by approximately 30°. These trends may indicate that promotion of wastewater fouling may improve the performance of capillary dependent fluids management systems. These results may also influence terrestrial technologies, including medical catheters and sustainable wastewater treatment systems exposed to wastewater fouling.     

Optimization of ultraviolet ozone treatment process for improvement of polycaprolactone (PCL) microcarrier performance

Growing cells on microcarriers may have overcome the limitation of conventional cell culture system. However, the surface functionality of certain polymeric microcarriers for effective cell attachment and growth remains a challenge. Polycaprolactone (PCL), a biodegradable polymer has received considerable attention due to its good mechanical properties and degradation rate. The drawback is the non-polar hydrocarbon moiety which makes it not readily suitable for cell attachment. This report concerns the modification of PCL microcarrier surface (introduction of functional oxygen groups) using ultraviolet irradiation and ozone (UV/O₃) system and investigation of the effects of ozone concentration, the amount of PCL and exposure time; where the optimum conditions were found to be at 60,110.52 ppm, 5.5 g PCL and 60 min, respectively. The optimum concentration of carboxyl group (COOH) absorbed on the surface was 1495.92 nmol/g and the amount of gelatin immobilized was 320 ± 0.9 µg/g on UV/O₃ treated microcarriers as compared to the untreated (26.83 ± 3 µg/g) microcarriers. The absorption of functional oxygen groups on the surface and the immobilized gelatin was confirmed with the attenuated total reflectance Fourier transformed infrared spectroscopy (ATR-FTIR) and the enhancement of hydrophilicity of the surface was confirmed using water contact angle measurement which decreased (86.93°–49.34°) after UV/O₃ treatment and subsequently after immobilization of gelatin. The attachment and growth kinetics for HaCaT skin keratinocyte cells showed that adhesion occurred much more rapidly for oxidized surfaces and gelatin immobilized surface as compared to untreated PCL.     

Engineered antifouling microtopographies – correlating wettability with cell attachment

Abstract

Bioadhesion and surface wettability are influenced by microscale topography. In the present study, engineered pillars, ridges and biomimetic topography inspired by the skin of fast moving sharks (Sharklet AF?) were replicated in polydimethylsiloxane elastomer. Sessile drop contact angle changes on the surfaces correlated well (R² = 0.89) with Wenzel and Cassie and Baxter's relationships for wettability. Two separate biological responses, i.e. settlement of Ulva linza zoospores and alignment of porcine cardiovascular endothelial cells, were inversely proportional to the width (between 5 and 20 μm) of the engineered channels. Zoospore settlement was reduced by ～85% on the finer (ca 2 μm) and more complex Sharklet AF? topographies. The response of both cell types suggests their responses are governed by the same underlying thermodynamic principles as wettability.     

Characterisation and in vitro activities of surface attached dihydropyrrol-2-ones against Gram-negative and Gram-positive bacteria

Bacterial infection of biomedical devices is still a major barrier to their use. This is compounded by increasing antibiotic resistance. Here, the specific covalent attachment of a series of dihydropyrrol-2-one (DHP), analogues of bacterial quorum sensing inhibitors, to surfaces via a Michael-type addition reaction is described. Differences in efficiency of attachment related to the substituent groups were found by X-ray photoelectron spectroscopy. The physical characteristics of the surfaces were further explored by atomic force microscopy and contact angle measurements. The ability of these coatings to prevent the formation of a biofilm by Pseudomonas aeruginosa and Staphylococcus aureus was examined using confocal laser scanning microscopy and image analysis. The DHP-treated surfaces showed significant reductions in bacterial adhesion without increased killing for both strains of bacteria (p < 0.001). 5-Methylene-1-(prop-2-enoyl)-4-phenyl-dihydropyrrol-2-one was identified as having broad spectrum activity and consequently represents an excellent candidate for the development of novel surfaces for the prevention of biomedical device infections.     

Biosurfactants as Agents to Reduce Adhesion of Pathogenic Bacteria to Polystyrene Surfaces: Effect of Temperature and Hydrophobicity

Polystyrene surfaces were conditioned with surfactin and rhamnolipid biosurfactants and then assessed regarding the attachment of Staphylococcus aureus, Listeria monocytogenes, and Micrococcus luteus. The effect of different temperatures (35, 25, and 4°C) on the anti-adhesive activity was also studied. Microbial adhesion to solvents and contact angle measurements were performed to characterize bacteria and material surfaces. The results showed that surfactin was able to inhibit bacterial adhesion in all the conditions analyzed, giving a 63–66% adhesion reduction in the bacterial strains at 4°C. Rhamnolipid promoted a slight decrease in the attachment of S. aureus. The anti-adhesive activity of surfactin increased with the decrease in temperature, showing that this is an important parameter to be considered in surface conditioning tests. Surfactin showed good potential as an anti-adhesive compound that can be explored to protect surfaces from microbial contamination.     

Ultrahydrophobicity indicates a non-adhesive default state in gecko setae

Geckos may represent the world’s most demanding adhesives application. The adhesive setae on the toes of climbing geckos must adhere strongly yet avoid fouling or attachment at inappropriate times. We tested the hypothesis that gecko setae are non-adhesive in their unloaded default state by comparing the water droplet contact angle (θ) of isolated setal arrays to the smooth surface of eye spectacle scales of tokay geckos (Gekko gecko). At equilibrium, θ was 98.3 ± 3.4° in spectacle scales of live geckos and 93.3 ± 3.5° in isolated spectacles. Isolated setal arrays were ultrahydrophobic, with θ of 160.6 ± 1.3° (means ± SD). The difference in θ of setal arrays and smooth spectacles indicates a very low contact fraction. Using Cassie’s law of surface wettability, we infer that less than 6.6% of the surface of unloaded setae is solid and at least 93.4% is air space. We calculated that the contact fraction must increase from 6.6% in the unloaded state to 46% in the loaded state to account for previously measured values of adhesion. Thus gecko setae may be non-sticky by default because only a very small contact fraction is possible without mechanically deforming the setal array.     

Antimicrobial activity of four cationic peptides immobilised to poly-hydroxyethylmethacrylate

The objective of this study was to immobilise and characterise a variety of antimicrobial peptides (AMPs) onto poly-hydroxyethylmethacrylate (pHEMA) surfaces to achieve an antibacterial effect. Four AMPs, viz. LL-37, melimine, lactoferricin and Mel-4 were immobilised on pHEMA by 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride (EDC) which assisted covalent attachment. Increasing concentrations of AMPs were immobilised to determine the effect on the adhesion of Pseudomonas aeruginosa and Staphylococcus aureus. The AMP immobilised pHEMAs were characterised by X-ray photoelectron spectroscopy (XPS) to determine the surface elemental composition and by amino acid analysis to determine the total amount of AMP attached. In vitro cytotoxicity of the immobilised pHEMA samples to mouse L929 cells was investigated. Melimine and Mel-4 when immobilised at the highest concentrations showed 3.1 ± 0.6 log and 1.3 ± 0.2 log inhibition against P. aeruginosa, and 3.9 ± 0.6 log and 2.4 ± 0.5 log inhibition against S. aureus, respectively. Immobilisation of LL-37 resulted in up to 2.6 ± 1.0 log inhibition against only P. aeruginosa, but no activity against S. aureus. LFc attachment showed no antibacterial activity. Upon XPS analysis, immobilised melimine, LL-37, LFc and Mel-4 had 1.57 ± 0.38%, 1.13 ± 1.36%, 0.66 ± 0.47% and 0.73 ± 0.32% amide nitrogen attached to pHEMA compared to 0.12 ± 0.14% in the untreated controls. Amino acid analysis determined that the total amount of AMP attachment to pHEMA was 44.3 ± 7.4 nmol, 3.8?±?0.2?nmol, 6.5 ± 0.6 nmol and 48.9 ± 2.3 nmol for the same peptides respectively. None of the AMP immobilised pHEMA surfaces showed any toxicity towards mouse L929 cells. The immobilisation of certain AMPs at nanomolar concentration to pHEMA is an effective option to develop a stable antimicrobial surface.     

Cell surface hydrophobicity of colistin-susceptible vs resistant Acinetobacter baumannii determined by contact angles: methodological considerations and implications

Contact angle analysis of cell surface hydrophobicity (CSH) describes the tendency of a water droplet to spread across a lawn of filtered bacterial cells. Colistin‐induced disruption of the Gram‐negative outer membrane necessitates hydrophobic contacts with lipopolysaccharide (LPS). We aimed to characterize the CSH of Acinetobacter baumannii using contact angles, to provide insight into the mechanism of colistin resistance. Contact angles were analysed for five paired colistin‐susceptible and resistant Ac. baumannii strains. Drainage of the water droplet through bacterial layers was demonstrated to influence results. Consequently, measurements were performed 0·66 s after droplet deposition. Colistin‐resistant cells exhibited lower contact angles (38·8±2·8–46·8±1·3°) compared with their paired colistin‐susceptible strains (40·7±3·0–48·0±1·4°; anova ; P < 0·05). Contact angles increased at stationary phase (50·3±2·9–61·5±2·5° and 47·4±2·0–50·8±3·2°, susceptible and resistant, respectively, anova ; P < 0·05) and in response to colistin 32 mg l^?1 exposure (44·5±1·5–50·6±2·8° and 43·5±2·2–48·0±2·2°, susceptible and resistant, respectively; anova ; P < 0·05). Analysis of complemented strains constructed with an intact lpxA gene, or empty vector, highlighted the contribution of LPS to CSH. Compositional outer‐membrane variations likely account for CSH differences between Ac. baumannii phenotypes, which influence the hydrophobic colistin–bacterium interaction. Important insight into the mechanism of colistin resistance has been provided. Greater consideration of contact angle methodology is necessary to ensure accurate analyses are performed.     

Effects of adsorbed organic and primary fouling films on bryozoan settlement

Marine primary fouling films, which consist of molecular organic and microbial components, have been reported to facilitate colonization of immersed surfaces by marine fouling organisms. Larvae of the cosmopolitan fouling bryozoan Bugula neritina (Linnaeus) were offered various substrata for attachment and metamorphosis. The materials were offered (a) after detergent washing, (b) after sorption of dissolved organic molecular films, and (c) after formation of primary films consisting of both microbial and adsorbed organic material. Wettability of the substrata by sea water was determined by contact angle measurements for each substratum. On washed substrata, attachment was favored with contact angles greater than ≈45° (cos contact angle <0.7). Adsorbed surface films had no effect on the low settlement of larvae on glass and high settlement on plastics. Microbial primary films, however, made glass attractive and plastics unattractive. These settlement preference changes did not correlate with the changes in wettability observed on these substrata. Dispersion of larvae over the settlement surface was random except on wettable surfaces coated with bacterial films, where settlement was strongly clustered (contagious).     

Biofilm formation by the yeast Rhodotorula mucilaginosa: process,repeatability and cell attachment in a continuous biofilm reactor

Yeast biofilms contribute to quality impairment of industrial processes and also play an important role in clinical infections. Little is known about biofilm formation and their treatment. The aim of this study was to establish a multi-layer yeast biofilm model using a modified 3.7 l bench-top bioreactor operated in continuous mode (D = 0.12 h^?1). The repeatability of biofilm formation was tested by comparing five bioprocesses with Rhodotorula mucilaginosa, a strain isolated from washing machines. The amount of biofilm formed after 6 days post inoculation was 83 μg cm^?2 protein, 197 μg cm^?2 polysaccharide and 6.9 × 10⁶ CFU cm^?2 on smooth polypropylene surfaces. Roughening the surface doubled the amount of biofilm but also increased its spatial variability. Plasma modification of polypropylene significantly reduced the hydrophobicity but did not enhance cell attachment. The biofilm formed on polypropylene coupons could be used for sanitation studies.     

Effect of incubation temperature on muscle growth of barramundi Lates calcarifer at hatch and post-exogenous feeding

Muscle morphology was investigated in newly hatched barramundi Lates calcarifer larvae incubated at set temperatures (26, 29 and 31° C) prior to hatching. Three days after hatching (the start of exogenous feeding), larvae from the 26 and 31° C treatments were each divided into two groups and reared at that temperature or transferred over the period of several hours to 29° C (control temperature). Incubation temperature significantly affected muscle cellularity in the developing embryo, with larvae incubated at 26° C (mean ±s .e . 223·3 ± 7·9) having on average 14·4% more inner muscle fibres than those incubated at 31° C (195·2 ± 8·8) and 4·8% more than those incubated at 29° C (213·5 ± 4·7). Conversely, inner muscle fibre cross‐sectional area significantly increased at the warm incubation temperature in L. calcarifer, so that the total cross‐sectional muscle area was not different between treatment groups. The total cross‐sectional area of superficial muscle fibres and the proportion of superficial to total fibre cross‐sectional area in just hatched L. calcarifer were also affected by incubation temperature, with incubation at the cool temperature (26° C) increasing both the total cross‐sectional area and proportion of superficial muscle fibres. By 9 days post‐hatch, the aforementioned differences were no longer significant. Similarly, there was no difference in total superficial fibre cross‐sectional area between any treatment groups of L. calcarifer, whereas incubation temperature still significantly affected the proportion of superficial to total muscle fibre cross‐sectional area. Larvae hatched and grown at 31° C had a significantly reduced percentage of superficial muscle cross‐sectional area (mean ±s .e . 5·11 ± 0·66%) compared with those incubated and grown at 29° C (8·04 ± 0·77%) and 26° C (9·32 ± 0·56%) and those incubated at 26° C and transferred to 29° C (7·52 ± 0·53%), and incubated at 31° C and transferred to 29° C (6·28 ± 0·69%). These results indicate that changes in muscle cellularity induced by raising or lowering the incubation temperature of L. calcarifer display varying degrees of persistence over developmental time. The significance of these findings to the culture of L. calcarifer is discussed.     

Investigation of the role of hydrophilic chain length in amphiphilic perfluoropolyether/poly(ethylene glycol) networks: towards high-performance antifouling coatings

The facile preparation of amphiphilic network coatings having a hydrophobic dimethacryloxy-functionalized perfluoropolyether (PFPE-DMA; M _w = 1500 g mol^?1) crosslinked with hydrophilic monomethacryloxy functionalized poly(ethylene glycol) macromonomers (PEG-MA; M _w = 300, 475, 1100 g mol^?1), intended as non-toxic high-performance marine coatings exhibiting antifouling characteristics is demonstrated. The PFPE-DMA was found to be miscible with the PEG-MA. Photo-cured blends of these materials containing 10 wt% of PEG-MA oligomers did not swell significantly in water. PFPE-DMA crosslinked with the highest molecular weight PEG oligomer (ie PEG1100) deterred settlement (attachment) of algal cells and cypris larvae of barnacles compared to a PFPE control coating. Dynamic mechanical analysis of these networks revealed a flexible material. Preferential segregation of the PEG segments at the polymer/air interface resulted in enhanced antifouling performance. The cured amphiphilic PFPE/PEG films showed decreased advancing and receding contact angles with increasing PEG chain length. In particular, the PFPE/PEG1100 network had a much lower advancing contact angle than static contact angle, suggesting that the PEG1100 segments diffuse to the polymer/water interface quickly. The preferential interfacial aggregation of the larger PEG segments enables the coating surface to have a substantially enhanced resistance to settlement of spores of the green seaweed Ulva, cells of the diatom Navicula and cypris larvae of the barnacle Balanus amphitrite as well as low adhesion of sporelings (young plants) of Ulva, adhesion being lower than to a polydimethyl elastomer, Silastic T2.     

Engineered antifouling microtopographies: the role of Reynolds number in a model that predicts attachment of zoospores of Ulva and cells of Cobetia marina

A correlation between the attachment density of cells from two phylogenetic groups (prokaryotic Bacteria and eukaryotic Plantae), with surface roughness is reported for the first time. The results represent a paradigm shift in the understanding of cell attachment, which is a critical step in the biofouling process. The model predicts that the attachment densities of zoospores of the green alga, Ulva, and cells of the marine bacterium, Cobetia marina, scale inversely with surface roughness. The size and motility of the bacterial cells and algal spores were incorporated into the attachment model by multiplying the engineered roughness index (ERI_II), which is a representation of surface energy, by the Reynolds number (Re) of the cells. The results showed a negative linear correlation of normalized, transformed attachment density for both organisms with ERI_II · Re (R ² = 0.77). These studies demonstrate for the first time that organisms respond in a uniform manner to a model, which incorporates surface energy and the Reynolds number of the organism.     

The role of surface energy and water wettability in aminoalkyl/fluorocarbon/hydrocarbon-modified xerogel surfaces in the control of marine biofouling

Xerogel films with uniform surface topogrophy, as determined by scanning electron microscopy, atomic force microscopy (AFM), and time-of-flight secondary ion mass spectrometry, were prepared from aminopropylsilyl-, fluorocarbonsilyl-, and hydrocarbonsilyl- containing precursors. Young's modulus was determined from AFM indentation measurements. The xerogel coatings gave reduced settlement of zoospores of the marine fouling alga Ulva compared to a poly(dimethylsiloxane) elastomer (PDMSE) standard. Increased settlement correlated with decreased water wettability as measured by the static water contact angle, θ_Ws, or with decreased polar contribution (γ_P) to the surface free energy (γ_S) as measured by comprehensive contact angle analysis. The strength of attachment of 7-day sporelings (young plants) of Ulva on several of the xerogels was similar to that on PDMSE although no overall correlation was observed with either θ_Ws or γ_S. For sporelings attached to the fluorocarbon/hydrocarbon-modified xerogels, the strength of attachment increased with increased water wettability. The aminopropyl-modified xerogels did not follow this trend.