Adhesion study of silicone coatings: the interaction of thickness, modulus and shear rate on adhesion force

Interactions between coating thickness, modulus and shear rate on pseudobarnacle adhesion to a platinum-cured silicone coating were studied using a statistical experimental design. A combined design method was used for two mixture components and two process variables. The two mixture components, vinyl end-terminated polydimethylsiloxanes (V21: MW=6 kg mole(-1) and V35: MW=4 9.5 kg mole(-1), Gelest Inc.) were mixed at five different levels to vary the modulus. The dry coating thickness was varied from 160 - 740 microm and shear tests were performed at four different shear rates (2, 7, 12, and 22 microm s(-1)). The results of the statistical analysis showed that the mixture components were significant factors on shear stress, showing an interaction with the process variable. For the soft silicone coating based on the high molecular weight polydimethylsiloxane (E=0.08 MPa), shear stress significantly increased as coating thickness decreased, while shear rate slightly impacted shear force especially at 160 microm coating thickness. As the modulus was increased (E=1.3 MPa), more force was required to detach the pseudobarnacle from the coatings, but thickness and rate dependence on shear stress became less important.     

Release characteristics of reattached barnacles to non-toxic silicone coatings

Release mechanisms of barnacles (Amphibalanus amphitrite or Balanus amphitrite) reattached to platinum-cured silicone coatings were studied as a function of coating thickness (210-770 microm), elastic modulus (0.08-1.3 MPa), and shear rate (2-22 microm s(-1)). It was found that the shear stress of the reattached, live barnacles necessary to remove from the silicone coatings was controlled by the combined term (E/t)(0.5) of the elastic modulus (E) and thickness (t). As the ratio of the elastic modulus to coating thickness decreased, the barnacles were more readily removed from the silicone coatings, showing a similar release behavior to pseudobarnacles (epoxy glue). The barnacle mean shear stress ranged from 0.017 to 0.055 MPa whereas the pseudobarnacle mean shear stress ranged from 0.022 to 0.095 MPa.     

Fluid–structure interactions in micro-interlocked regions of the cement–bone interface

Experimental tests and computational modelling were used to explore the fluid dynamics at the trabeculae–cement interlock regions found in the tibial component of total knee replacements. A cement–bone construct of the proximal tibia was created to simulate the immediate post-operative condition. Gap distributions along nine trabeculae–cement regions ranged from 0 to 50.4 μm (mean = 12 μm). Micro-motions ranged from 0.56 to 4.7 μm with a 1 MPa compressive load to the cement. Fluid–structure analysis between the trabeculae and the cement used idealised models with parametric evaluation of loading direction, gap closing fraction (GCF), gap thickness, loading frequency and fluid viscosity. The highest fluid shear stresses (926 Pa) along the trabecular surface were found for conditions with very thin and large GCFs, much larger than reported physiological levels (～1–5 Pa). A second fluid–structure model was created with a provision for bone resorption using a constitutive model with resorption velocity proportional to fluid shear rate. A lower cut-off was used, below which bone resorption would not occur (50 s^? 1). Results showed that there was initially high shear rates (>1000 s^? 1) that diminished after initial trabecular resorption. Resorption continued in high shear rate regions, resulting in a final shape with bone left deep in the cement layer, and is consistent with morphology found in post-mortem retrievals. Small gaps between the trabecular surface and the cement in the immediate post-operative state produce fluid flow conditions that appear to be supra-physiologic; these may cause fluid-induced lysis of trabeculae in the micro-interlock regions.     

A DFT study on the second-order nonlinear optical properties of the plenary mixed-metal polyoxometalate

The redox and second-order nonlinear optical (NLO) properties of organic–inorganic hybrid polyoxoanions [LNbOEMe₃]^3 ? , [LNbOEPh₃]^3 ?  (L = α-{PW₁₁O₃₉}^7 ? , E = Si, Ge, Sn, Pb) are investigated by density functional theory method. The element substitution effects on the molecular nonlinear response have been analysed. The results show that the computed β₀ values depend on both E (E = Si < Ge < Sn < Pb) and the organic groups connected with E. For [LNbOEPh₃]^3 ?  (L = α-{PW₁₁O₃₉}^7 ? , E = Si, Ge, Sn, Pb), the analysis of major contributions to β₀ value suggests that the charge transfer from organic group to Keggin polyanion plays the key role in NLO response; the polyanion acts as a donor, whereas the organic group acts as an acceptor in [LNbOEPh₃]^3 ? . Our results show that this kind of organic–inorganic hybrid compound possesses larger molecular second-order polarisability and might be a potential NLO material.     

Kinetic study of Lactococcus lactis strains (SLT6 and SLT10) growth on papain-hydrolysed whey

The effect of controlled whey hydrolysis by papain on growth of two lactic acid bacteria isolated from artisanal Leben: Lactococcus lactis var. diacetylactis (SLT6 and SLT10) was investigated. The higher biomass and maximum specific growth rate (μ _max) were obtained after 30 min of hydrolysis. HPLC analysis of peptides showed that whey hydrolysis reduced the amount of peptides of MW > 400 Da and increased those peptides of MW < 400 Da. The two studied strains exhibited different peptide requirements. The pH-controlled batch cultures in 30 min hydrolysed whey followed the Monod kinetic for growth and for lactate production. The values of the key kinetic constants were: maximum specific growth rate (μ _max), 1.08 and 0.56 h^?1; yield biomass on lactose (Y _x/s), 0.20 and 0.18 g g^?1 and saturation constant K _s, 4.2 and 2.8 g L^?1 for SLT6 and SLT10, respectively. When compared with batch experimental data, the model provided good predictions for growth, lactose utilisation and lactate production profiles.     

Sediment microstructure and resuspension behavior depend on each other

The critical shear stress of resuspension and rates of erosion for cohesive and loosely structured sediments must be obtained by direct measurements since there is no theoretical calculation. An in situ experiment on sediment resuspension was performed in a shallow lake (Langer See, NE Germany; area = 1.27 km², z_max = 3.8 m) in summer 2006 using a hydrodynamically calibrated erosion chamber (Ø 20 cm). Shear velocity (u*) was incrementally increased in 11 steps (0–2.19 cm s^?1) to initiate resuspension events. Entrainment rates (E) of suspended particulate matter (E_SPM), total P (E_TP), chlorophyll a (E_Chl a), and soluble reactive P (E_SRP) were determined by mass balance. Two subsequent critical u* (0.53 cm s^?1 and 1.48 cm s^?1) support the ‘two-layered bed’ model of a fluffy surface aggregate layer (freshly deposited phytodetritus prone to resuspension) and an underlying more consolidated biostabilised layer. Patterns in E_SPM (2–106 g m^?2 h^?1), E_TP (11–532 mg m^?2 h^?1), and E_Chl a (3–24 μg m^?2 h^?1) revealed a sediment surface maximum of TP and Chl a and their theoretical vertical logarithmic decrease within 4 mm sediment depth, the maximum thickness of sediment layer entrained. The advective E_SRP flux (17 mg m^?2 h^?1) was 43 times higher than the diffusive SRP flux (0.4 mg m^?2 h^?1). The TP and Chl a micro-profiles suggest that cohesive sediment bed formation is a function of both settling (fluff) and consolidation (biostabilisation). Thus, sediment microstructure and resuspension behavior depend on each other.     

Specific light uptake rates can enhance astaxanthin productivity in <Emphasis Type="Italic">Haematococcus lacustris</Emphasis>

Lumostatic operation was applied for efficient astaxanthin production in autotrophic Haematococcus lacustris cultures using 0.4-L bubble column photobioreactors. The lumostatic operation in this study was performed with three different specific light uptake rates (q _e) based on cell concentration, cell projection area, and fresh weight as one-, two- and three-dimensional characteristics values, respectively. The q _e value from the cell concentration (q _e1D) obtained was 13.5 × 10^?8 μE cell^?1 s^?1, and the maximum astaxanthin concentration was increased to 150 % compared to that of a control with constant light intensity. The other optimum q _e values by cell projection area (q _e2D) and fresh weight (q _e3D) were determined to be 195 μE m^?2 s^?1 and 10.5 μE g^?1 s^?1 for astaxanthin production, respectively. The maximum astaxanthin production from the lumostatic cultures using the parameters controlled by cell projection area (2D) and fresh weight (3D) also increased by 36 and 22 % over that of the controls, respectively. When comparing the optimal q _e values among the three different types, the lumostatic cultures using q _e based on fresh weight showed the highest astaxanthin productivity (22.8 mg L^?1 day^?1), which was a higher level than previously reported. The lumostatic operations reported here demonstrated that more efficient and effective astaxanthin production was obtained by H. lacustris than providing a constant light intensity, regardless of which parameter is used to calculate the specific light uptake rate.     

Process Engineering for High-Cell-Density Cultivation of Lipid Rich Microalgal Biomass of <Emphasis Type="Italic">Chlorella</Emphasis> sp. FC2 IITG

In the present study, process engineering strategy was applied to achieve lipid-rich biomass with high density of Chlorella sp. FC2 IITG under photoautotrophic condition. The strategy involved medium optimization, intermittent feeding of limiting nutrients, dynamic change in light intensity, and decoupling growth and lipid induction phases. Medium optimization was performed using combinations of artificial neural network or response surface methodology with genetic algorithm (ANN-GA and RSM-GA). Further, a fed-batch operation was employed to achieve high cell density with intermittent feeding of nitrate and phosphate along with stepwise increase in light intensity. Finally, mutually exclusive biomass and lipid production phases were decoupled into two-stage cultivation process: biomass generation in first stage under nutrient sufficient condition followed by lipid enrichment through nitrogen starvation. The key findings were as follows: (i) ANN-GA resulted in an increase in biomass titer of 157 % (0.95 g L^?1) in shake flask and 42.8 % (1.0 g L^?1) in bioreactor against unoptimized medium at light intensity of 20 μE m^?2 s^?1; (ii) further optimization of light intensity in bioreactor gave significantly improved biomass titer of 5.6 g L^?1 at light intensity of 250 μE m^?2 s^?1; (iii) high cell density of 13.5 g L^?1 with biomass productivity of 675 mg L^?1 day^?1 was achieved with dynamic increase in light intensity and intermittent feeding of limiting nutrients; (iv) finally, two-phase cultivation resulted in biomass titer of 17.7 g L^?1 and total lipid productivity of 313 mg L^?1 day^?1 which was highest among Chlorella sp. under photoautotrophic condition.     

Spontaneous mutation frequency and molecular mechanisms of Shigella flexneri fluoroquinolone resistance under antibiotic selective stress

The incidence of fluoroquinolone-resistant Shigella strains has risen rapidly, presumably in response to ciprofloxacin antibiotic stress. Understanding the molecular mechanisms underlying this resistance phenotype is critical to developing novel and effective therapeutic strategies. In this study, the frequency of ciprofloxacin-induced mutation was measured in antibiotic resistance genes (gyrA, gyrB, parC, parE, marOR, and marA) of Shigella flexneri. The S. flexneri 2a strain 301 was cultured on Luria–Bertani agar plates containing one of seven different ciprofloxacin concentrations (range: 0.03125–2 μg mL^?1). Resistant colonies were selected for gene-targeted sequencing analysis; the identified point mutations were subsequently confirmed by insertion into antibiotic cassette plasmids and growth under ciprofloxacin stress. The results demonstrated that the seven different ciprofloxacin concentrations produced dose-dependent frequencies of spontaneous mutations: 10^?8 (0.03125 and 0.0625 μg mL^?1), 10^?9 (0.125 μg mL^?1), and <10^?9 (0.25, 0.5, 1, 2 μg mL^?1). PCR sequencing of the ten randomly selected resistant colonies (minimum inhibitory concentrations (MICs) of 0.125 μg mL^?1, n = 5 and 0.25 μg mL^?1, n = 5) revealed that all colonies had mutations in the gyrA gene at either codon 83 (Ser83 → Leu) or 87 (Asp87 → Tyr or → Gly), both of which were confirmed at MIC of 0.125 μg mL^?1. None of the spontaneous mutation colonies exhibited gyrB, parC, parE, marOR, or marA mutations. In conclusion, S. flexneri is normomutable under ciprofloxacin antibiotic stress and fluoroquinolone resistance by spontaneous mutation occurs at a low rate. Codon mutations gyrA 83 and/or gyrA 87 cause a 4-fold increase in the ciprofloxacin MIC, and may represent the natural mechanism of fluoroquinolone resistance.     

Effects of temperature on growth of Vallisneria americana in a sub-tropical estuarine environment

The submersed aquatic vegetation (SAV) species Vallisneria americana Michx. (tape grass) is a valuable resource in the Caloosahatchee estuary and in many other aquatic systems. Given the variable nature of freshwater inflows and environmental conditions in the Caloosahatchee, it is necessary to understand how tape grass will respond to high and low salinity conditions at different light and temperature levels. Specifically, quantitative information is needed as input to modeling tools that can be applied to predict growth and survival of tape grass under a range of environmental conditions present in the estuary. We determined growth rates for small and medium sized tape grass plants obtained from the Caloosahatchee estuary, southwest coastal Florida, USA in freshwater (0.5 psu) under high (331 μE m^?2 s^?1) and low light (42 μE m^?2 s^?1) and at 10 psu under high light conditions. We ran six treatments at five temperatures spanning 13–32 °C for 8–9 weeks. The optimum temperature for growth was roughly 28 °C, with a minimum threshold temperature of 13 °C and a maximum threshold temperature of 38 °C. Plants grew fastest in freshwater, at high light and temperatures greater than 20 °C. The slowest growth rates were observed at 13 °C regardless of salinity, light or plant size. Our results suggest that tape grass growth is strongly influenced by water temperature and that additional stressors such as low light and elevated salinity can reduce the range of temperature tolerance, especially at colder water temperatures.     

Lake Chapo: a baseline study of a deep, oligotrophic North Patagonian lake prior to its use for hydroelectricity generation: I. Physical and chemical properties

A baseline study on a temperate, oligotrophic North Patagonian lake (Lake Chapo, Southern Chile) was made prior to the installation of a hydroelectric power station. Throughout one year (September 1986–October 1987) the physical and chemical properties of the lake were investigated monthly from the surface to a depth of 40 m. Lake Chapo is a deep, transparent (Secchi depth: 17–25 m), glacial lake located at 41°?27.5′?S and 72°?30′?W. It has a maximum depth of 298 m, mean depth of 183 m, surface area of 45.3 km² and water volume of 8.296 km³. The theoretical residence time of the water was 5.5 years. The temperature regime is monomictic with the mixed temperature between 8.1–8.8?°C. Maximum temperature at the surface was 18.7?°C during thermal stratification in summer when the epilimnion had a thickness of about 20 m. The conductivity was low (20.3–23.8 μS cm^?1) as was the buffering capacity of a predominantly CO₂-carbonate system. The predominant cations were Ca⁺²¿ Na⁺¿Mg⁺²¿K⁺. The phosphorous and nitrogen contents were very low (soluble reactive ortophosphate: 0–1.5 μg P l^?1, total phosphorus: 0.3–4 μg P l^?1 and nitrate: 0–35 μg N l^?1), which is typical of North Patagonian lakes.     

Analysis of the binding of phenylalanine to phenylalanyl-tRNA synthetase

Using the complete rate equation for the PP_i-ATP exchange reaction at equilibrium, the dissociation constants of phenylalanine (10^?5m), phenylalanine butyl ester (8 × 10^?5m), benzyl alcohol (6 × 10^?4m), phenylalaninol (2 × 10^?4m), hydrocinnamic acid (3 × 10^?3m) and glycine (>1 m) with the phenylalanyl-tRNA synthetase (Escherichia coli K12) were determined. Taking the model of Koshland (1962) for the estimation of the configurational free energy change due to proximity and orientation, and decomposing the process of binding into several thermodynamic steps, the contribution to binding of the benzyl group, glycine unit, protonated amino group, carboxylate group and joint interactions were estimated. The results are: (1) the standard free energy contributions for binding phenylalanine are benzyl group (?8.2 kcal/mol), glycine unit (?2.5 kcal/mol), protonated amino group (?0.8 kcal/mol) and carboxylate group (1 kcal/mol). (2) The standard free energy change due to the change in the interaction between the protonated amino group and carboxylate group when they are transferred from the aqueous environment to the enzyme environment is ?2.7 kcal/mol. (3) A dissociation constant for glycine of 7.5 m is calculated without the hypothesis that a conformational change occurs in the enzyme when the benzyl unit of phenylalanine binds, permitting an interaction of the enzyme with the protonated amino and/or carboxylate groups.The detection of E·AA² and E·ATP shows that a sequential addition of substrates is not necessary for binding. A comparison of the dissociation constants of E·AA (10^?5m), E·ATP (1.5 × 10^?3m), E·PP (5.5 × 10^?4m), E·I (8 × 10^?5m) and the mixed complexes E·I·ATP (6 × 10^?8m²), E·I·PP (5 × 10^?8m²) and E·AA·PP (7 × 10^?9m²), with phenylalanine butyl ester as the inhibitor, indicates no strong interaction between the binding of ATP or PP_i with the binding of phenylalanine.     

Nutrient uptake rates by the alien alga Undaria pinnatifida (Phaeophyta) (Nuevo Gulf, Patagonia, Argentina) when exposed to diluted sewage effluent

In the early nineties, Undaria pinnatifida has been accidentally introduced to Nuevo Gulf (Patagonia, Argentina) where the environmental conditions would have favored its expansion. The effect of the secondary treated sewage discharge from Puerto Madryn city into Nueva Bay (located in the western extreme of Nuevo Gulf) is one of the probable factors to be taken into account. Laboratory cultures of this macroalgae were conducted in seawater enriched with the effluent. The nutrients (ammonium, nitrate and phosphate) uptake kinetics was studied at constant temperature and radiation (16?°C and 50 μE m^?2 s^?1 respectively). Uptake kinetics of both inorganic forms of nitrogen were described by the Michaelis–Menten model during the surge phase (ammonium: V _max ^sur: 218.1 μmol h^?1 g^?1, K _s ^sur: 476.5 μM and nitrate V _max ^sur: 10.7 μmol h^?1 g^?1, K _s ^sur: 6.1 μM) and during the assimilation phase (ammonium: V _max ^ass: 135.6 μmol h^?1 g^?1, K _s ^ass: 407.2 μM and nitrate V _max ^ass: 1.9 μmol h^?1 g^?1, K _s ^ass: 2.2 μM), with ammonium rates always higher than those of nitrate. Even though a net phosphate disappearance was observed in all treatments, uptake kinetics of this ion could not be properly estimated by the employed methodology.     

Toxicity of an Annonin-Based Commercial Bioinsecticide Against Three Primary Pest Species of Stored Products

The effects of a bioinsecticide formulation based on extract of Annona squamosa L. (Annonaceae) containing 10,000 mg L^?1 of acetogenin annonin as the main active ingredient were investigated against three primary pest species of stored grains in Brazil [maize weevil Sitophilus zeamais Motschulsky (Coleoptera: Curculionidae), Mexican bean weevil Zabrotes subfasciatus (Boheman) (Coleoptera: Chrysomelidae: Bruchinae), and cowpea weevil Callosobruchus maculatus (Fabricius) (Coleoptera: Chrysomelidae: Bruchinae)] by means of residual contact bioassays. In a concentration-dependent manner, the annonin-based commercial bioinsecticide caused significant adult mortality of C. maculatus (LC₅₀ = 6890 μL kg^?1), S. zeamais (LC₅₀ = 2781 μL kg^?1), and Z. subfasciatus (LC₅₀ = 2120 μL kg^?1) after 120 h of residual contact exposure. In addition to acute toxicity, the tested bioinsecticide also promoted a significant reduction of the number of eggs laid by females of C. maculatus (EC₅₀ = 5949.7 μL kg^?1) and Z. subfasciatus (EC₅₀ = 552.7 μL kg^?1). Moreover, the bioinsecticide significantly reduced the number of emerged insects (F₁ generation) of C. maculatus (EC₅₀ = 2763.0 μL kg^?1), S. zeamais (EC₅₀ = 1380.8 μL kg^?1), and Z. subfasciatus (EC₅₀ = 561.5 μL kg^?1). The bioinsecticide also reduced the percentage of damaged grains for the three pest species studied, and its grain-protectant properties are comparable to or superior in efficacy in relation to a diatomaceous earth-based insecticide (Insecto® at 1000 mg kg^?1) used as a positive control. Thus, this standardized formulation has promising bioactivity against stored insect species and can be a useful component for IPM of stored grains in Brazil and elsewhere.     

Investigation of human platelet adhesion under low shear conditions in a rotational flow chamber

Even though blood pumps have come into clinical usage, thrombo-embolic complications still pose a major problem, and they have not yet been clarified and quantified. However, it is known that the basis of thrombus formation is platelet adhesion, which is thought to be closely associated with the shear rate. Therefore, our current interest focuses on the effect of shear conditions on platelet adhesion. We have designed and carried out an experimental setup allowing fluorescent microscopy of whole blood within a rotational viscometer under controllable shear conditions. A small area of the bottom plate was coated with type I collagen, which provided a model of the injured vessel as a target for platelet adhesion. Using this setup, the time course of platelet adhesion under several different shear rates, ranging from 127 to 723 s^?1, was studied. Platelet adhesion increased along with shear rates up to 283 s^?1, followed by a gradual decrease when the shear rate exceeded 346 s^?1. The adhesion amounts were statistically significant between 283 and 173 s^?1 (p = 0.02), 173 and 127 s^?1 (p = 0.035), and 283 and 503 s^?1 (p = 0.03), respectively. This result suggests that there is an optimal shear condition around 300 s^?1 for platelet adhesion to type I collagen.     

THF INFLUENCE OF IRRADIANCE ON THF BIOCHEMICAL COMPOSITION OF THE PRYMNESIOPHYTE ISOCHRYSIS SP. (CLONE T-ISO)1

The effects of irradiance on the biochemical composition of the prymnesiophyte microalga, Isochrysis sp. (Parke; clone T-ISO), a popular species for mariculture, were examined. Cultures were grown under a 12:12 h light: dark (L:D) regime at five irradiances ranging from 50 to 1000 μE·m ²·s^?1 and harvested at late-logarithmic phase for analysis of biochemical composition. Gross composition varied aver the range of irradiances. The highest levels of protein were present in cells from cultures grown at 100 and 250 μE·m ³·s¹, and minimum levels of carbohydrate and lipid occurred at 50 μE·m^?2·s^?1. Because the cell dry weight was reduced at lower irradiances, different trends were evident when results were expressed as percentage of dry weights. Protein percentages were highest at Wand 100 μE·m^?2·s^?1 and carbohydrate at 100 μE·m^?2·s^?1. The composition of amino acids did not differ over the range of irradiances. Glutamate and aspartate were always present in high proportions (9.0–13.5%); histidine. methionine, tryptophan, cystine, and hydroxy-proline were minor constituents (0.0–2.6%). Glucose was the predominant sugar in all cultures, ranging from 23.0% (50 μE·m^?2·s^?1) to 45.0% (100 μE·m^?2·s^?1) of total polysaccharide. No correlation was found between the proportion of any of the sugars and irradiance. The proportions of the lipid class components and fatty acids showed little change with irradiance. The main fatty acids were 14:0, 16:0, 16:1(n-7), 18:1(n-9), 18:3(n-3). 18:4(n-3), 18:5(n-3), and 22:6(n-3). Proportions of 22: 6(n-3) increased, whereas l8:3(n-3). 18:3(n-6). and 18:4(n-3) decreased, with increasing irradiance. Pigment concentrations were highest in cultures grown at 50 μE·m^?2·s^?1, except for fucoxanthin and diadinoxanthin (100 μE·m^?2·s^?1). The concentrations of accessory pigments correlated with chlorophyll a, which decreased in concentration with increasing irradiance. On the basts of biochemical composition, an irradiance of 100 μE·m^?1·s^?1 (12:12 h L:D cycle)for the culture of Isochrysis sp. (clone T-ISO) may provide optimal nutritional value for maricultured animals, although feeding trials are now necessary to substantiate this.     

Evidence of elevated mercury levels in carnivorous and omnivorous fishes downstream from an Amazon reservoir

Hydroelectric reservoirs can stratify, producing favorable conditions for mercury methylation in the hypolimnion. The methylmercury (MeHg) can be exported downstream, increasing its bioavailability below the dam. Our objective was to assess the mercury levels in plankton, suspended particulate matter (SPM) and fish collected upstream (UP) and downstream (DW) from the Reservatório de Samuel dam, an Amazonian reservoir that stratifies during half of the year. Mercury concentrations in both SPM and plankton were similar between the two sites, which could indicate there are no conditions favoring methylation at the moment of sampling (absence of stratification). Almost all mercury found in the muscle of fishes was in organic form, and differences of mercury levels between sites were dependent on the fishes trophic level. Herbivores showed similar mean organic mercury levels (UP = 117 μg g^?1; DW = 120 μg g^?1; n = 12), whereas omnivores (UP = 142 μg g^?1; DW = 534 μg g^?1; n = 27) and carnivores (UP = 545 μg g^?1; DW = 1,366 μg g^?1; n = 69) showed significantly higher values below the dam. The absence of a reservoir effect in herbivores is expected, since they feed on grassy vegetation, near the riverbanks, which is not much influenced by mercury in aquatic systems. On the other hand, the higher mercury levels below the dam observed for omnivores and carnivores suggest a possible influence of the reservoir since they feed on items that could be contaminated by MeHg exported from upstream. The results highlight the necessity of assessing areas downstream of reservoirs.     

A Comparative Study of the Non-acidic Chemically Mediated Antifoulant Properties of Three Sympatric Species of Ascidians Associated with Seagrass Habitats

In this study, the mechanical properties of biofilms formed at the surface of nano-filtration (NF) membranes from a drinking water plant were analysed. Confocal laser scanning microscopy observations revealed that the NF biofilms formed a dense and heterogeneous structure at the membrane surface, with a mean thickness of 32.5 ± 17.7 μm. The biofilms were scraped from the membrane surface and analysed in rotation and oscillation experiments with a RheoStress 150 rotating disk rheometer. During rotation analyses, a viscosity decrease with speed of shearing characteristic of rheofluidification was observed (η = 300 Pa s for ý = 0.3 s^?1). In the oscillation analyses with a sweeping of frequency (1–100 Hz), elasticity (G′) ranged from 3000 to 3500 Pa and viscosity (G″) from 800 to 1200 Pa. Creep curves obtained with an application of a shear stress of 30 Pa were viscoelastic in nature. The G ₀ and η values were, respectively, 1.4 ± 0.3 × 10³ Pa and 3.3 ± 0.65 × 10⁶ Pa s. The relationship between the characteristics of NF biofilms and the flow conditions encountered during NF is discussed.     

Infrared Plasmonic Transmission Resonances of Gold Film with Hexagonally Ordered Hole Arrays on ZnSe Substrate

The high fractional open area of metal thin film coatings, with two dimensional, hexagonally ordered, close packed arrays of holes, makes them of interest for the incorporation of plasmonic effects into a variety of optical devices. Gold films with hexagonal patterns of circular holes have been created on ZnSe infrared windows. The films have 2.50 μm diameter holes and a hexagonal lattice parameter of 3.06 μm which places the primary transmission resonances of the ZnSe/gold interface at ~1,400 cm^?1 (7.14 μm) and that of the air/gold interface at ~3,800 cm^?1 (2.63 μm). This geometry produces useful transmission across the whole traditional mid-infrared range. The dispersion of these resonances has been measured by changing the angle of incident light. The data is modeled with explicit momentum matching equations in two different, high symmetry geometries, allowing the effective index of refraction to vary with wavelength. The response of these resonances to the addition of an acetaldehyde coating is described.     

Manipulation of culture strategies to enhance capsaicin biosynthesis in suspension and immobilized cell cultures of Capsicum chinense Jacq. cv. Naga King Chili

Manipulation of culture strategies was adopted to study the influence of nutrient stress, pH stress and precursor feeding on the biosynthesis of capsaicin in suspension and immobilized cell cultures of C. chinense. Cells cultured in the absence of one of the four nutrients (ammonium and potassium nitrate for nitrate and potassium stress, potassium dihydrogen orthophosphate for phosphorus stress, and sucrose for sugar stress) influenced the accumulation of capsaicin. Among the stress factors studied, nitrate stress showed maximal capsaicin production on day 20 (505.9 ± 2.8 μg g^?1 f.wt) in immobilized cell, whereas in suspension cultures the maximum accumulation (345.5 ± 2.9 μg g^?1 f.wt) was obtained on day 10. Different pH affected capsaicin accumulation; enhanced accumulation of capsaicin (261.6 ± 3.4 μg g^?1 f.wt) was observed in suspension cultures at pH 6 on day 15, whereas in case of immobilized cultures the highest capsaicin content (433.3 ± 3.3 μg g^?1 f.wt) was obtained at pH 5 on day 10. Addition of capsaicin precursors and intermediates significantly enhanced the biosynthesis of capsaicin, incorporation of vanillin at 100 μM in both suspension and immobilized cell cultures resulted in maximum capsaicin content with 499.1 ± 5.5 μg g^?1 f.wt on day 20 and 1,315.3 ± 10 μg g^?1 f.wt on day 10, respectively. Among the different culture strategies adopted to enhance capsaicin biosynthesis in cell cultures of C. chinense, cells fed with vanillin resulted in the maximum capsaicin accumulation. The rate of capsaicin production was significantly higher in immobilized cells as compared to freely suspended cells.