Iodine-infused aeration for hull fouling prevention: a vessel-scale study

Biofouling is a significant economic and ecological problem, causing reduced vessel performance and increases in fuel consumption and emissions. Previous research has shown iodine vapor (I₂)-infused aeration to be an environmentally friendly method for deterring the settlement of fouling organisms. An aeration system was deployed on a vessel with hull sections coated with two types of antifoulant coatings, Intersleek^® 1100 (fouling-release) and Interspeed^® BRA-640 (ablative copper biocide), as well as an inert epoxy barrier coating, to assess the effectiveness of aeration in conjunction with common marine coatings. I₂-infused aeration resulted in consistent reductions of 80–90% in hard fouling across all three coatings. Additionally, aeration reduced the soft fouling rate by 45–70% when used in conjunction with both Intersleek^® and Interspeed^® BRA versus those coatings alone. The results of this study highlight the contribution of I₂-infused aeration as a standalone mechanism for fouling prevention or as a complement to traditional antifouling coatings.     

Vessel generator noise as a settlement cue for marine biofouling species

Underwater noise is increasing globally, largely due to increased vessel numbers and international ocean trade. Vessels are also a major vector for translocation of non-indigenous marine species which can have serious implications for biosecurity. The possibility that underwater noise from fishing vessels may promote settlement of biofouling on hulls was investigated for the ascidian Ciona intestinalis. Spatial differences in biofouling appear to be correlated with spatial differences in the intensity and frequency of the noise emitted by the vessel’s generator. This correlation was confirmed in laboratory experiments where C. intestinalis larvae showed significantly faster settlement and metamorphosis when exposed to the underwater noise produced by the vessel generator. Larval survival rates were also significantly higher in treatments exposed to vessel generator noise. Enhanced settlement attributable to vessel generator noise may indicate that vessels not only provide a suitable fouling substratum, but vessels running generators may be attracting larvae and enhancing their survival and growth.     

Vanillin,a potential agent to prevent biofouling of reverse osmosis membrane

Reverse osmosis (RO) membrane systems are widely used in water purification plants. Reduction in plant performance due to biofilm formation over the membrane is an inherent problem. As quorum sensing (QS) mechanisms of microorganisms have been reported to be involved in the formation of biofilm, ways are sought for quorum quenching (QQ) and thereby prevention of biofilm formation. In this study using a chemostat culture run for seven days in a CDC reactor it was found that a natural QQ compound, vanillin considerably suppressed bacterial biofilm formation on RO membrane. There was 97% reduction in biofilm surface coverage, when grown in the presence of vanillin. Similarly, the average thickness, total biomass and the total protein content of the biofilm that formed in the presence of vanillin were significantly less than that of the control. However vanillin had no effect on 1-day old pre-formed biofilm.     

Effects of coating roughness and biofouling on ship resistance and powering

Abstract

Predictions of full-scale ship resistance and powering are made for antifouling coating systems with a range of roughness and fouling conditions. The estimates are based on results from laboratory-scale drag measurements and boundary layer similarity law analysis. In the present work, predictions are made for a mid-sized naval surface combatant at cruising speed and near maximum speed. The results indicate that slime films can lead to significant increases in resistance and powering, and heavy calcareous fouling results in powering penalties up to 86% at cruising speed. The present estimates show good agreement with results from full-scale ship power trials.     

Control of biofouling on pearl oysters Pinctada imbricata using wax and Chinese herbs

Abstract

Biofouling poses severe challenges to pearl oyster Pinctada imbricata culture in China, and controlling it is both labor- and capital-intensive. The antifouling properties of wax, and wax mixed with Chinese herbs, sprayed onto pearl oyster shell surfaces during peak biofouling seasons were evaluated. Pearl oysters coated with three wax treatments (plain wax, Chinaberry seed extract, Chinese honeylocust fruit extract) and a control (no treatment), were cultured in nets for up to 60?days. Mortality rate, fouling organism and pearl-oyster weights, and shell height are reported for individual oysters on each of six sampling dates. With the exception of oysters submerged for 12?days, all oysters were significantly affected by treatment type and submersion duration. Fouling weight increased more rapidly over time in the control-treatment oysters. Wax-based coatings deterred fouling-organism settlement on oysters for at least 2?months during the intensive fouling season, reducing mortality and not adversely effecting growth.     

Proteomic profiling during the pre-competent to competent transition of the biofouling polychaete Hydroides elegans

The polychaete, Hydroides elegans, is a tube-building worm that is widely distributed in tropical and subtropical seas. It is a dominant fouling species and thus a major target organism in antifouling research. Here, the first high-throughput proteomic profiling of pre-competent and competent larvae of H. elegans is reported with the identification of 1,519 and 1,322 proteins, respectively. These proteins were associated with a variety of biological processes. However, a large proportion was involved in energy metabolism, redox homeostasis, and microtubule-based processes. A comparative analysis revealed 21 proteins that were differentially regulated in larvae approaching competency.     

Polysulfone and polyacrylate-based zwitterionic coatings for the prevention and easy removal of marine biofouling

A series of polysulfone and polyacrylate-based zwitterionic coatings were prepared on epoxy-primed aluminum substrata and characterized for their antifouling (AF) and fouling-release (FR) properties towards marine bacteria, microalgae and barnacles. The zwitterionic polymer coatings provided minimal resistance against bacterial biofilm retention and microalgal cell attachment, but facilitated good removal of attached microbial biomass by exposure to water-jet apparatus generated hydrodynamic shearing forces. Increasing the ion content of the coatings improved the AF properties, but required a stronger adhesive bond to the epoxy-primed aluminum substratum to prevent coating swelling and dissolution. Grafted poly(sulfobetaine) (gpSBMA), the most promising zwitterionic coating identified from microfouling evaluations, enabled the removal of four out of five barnacles reattached to its surface without incurring damage to their baseplates. This significant result indicated that gpSBMA relied predominately on its surface chemistry for its FR properties since it was very thin (~1–2 µm) relative to commercial coating standards (>200 µm).     

The construction of a zwitterionic PVDF membrane surface to improve biofouling resistance

Biofouling of membrane surfaces by the attachment of microorganisms is one of the major obstacles for ensuring the effectiveness of membrane separation processes. This work presents the construction of a zwitterionic PVDF membrane surface with improved resistance to biofouling. An amphiphilic copolymer of poly(vinylidene fluoride)-graft-poly(N,N-dimethylamino-2-ethylmethacrylate) (PVDF-g-PDMAEMA) was first synthesized via radical graft copolymerization and then the flat membrane was cast with immersed phase inversion. The PDMAEMA side chains tended to aggregate on the membrane surface, pore surface and internal pore channel surface, and were converted with 1,3-propane sultone (1,3-PS) to yield a zwitterionic membrane surface. A higher conversion of PDMAEMA chains and distribution of zwitterions were obtained using a longer treatment time. A biofouling assay indicated that incorporation of zwitterions suppressed the adsorption of extracellar polymer substances and the adhesion of Escherichia coli bacterial cells to the membrane surface, endowing the membrane with a high flux recovery and biofouling resistance in the filtration process.     

Characterization and removal of biofouling from reverse osmosis membranes (ROMs) from a desalination plant in Northern Chile,using Alteromonas sp. Ni1-LEM supernatant

Abstract

Biofouling control in reverse osmosis membranes (ROMs) is challenging due to the high cost of treatments, and reduction in the life of ROMs. This study characterizes the biofouling in the ROMs from a desalination plant and reports its effective removal using the supernatant obtained from Alteromonas sp. strain Ni1-LEM. The characterization of the bacterial community revealed that the most abundant taxa in ROMs were the genera Fulvivirga and Pseudoalteromonas, and unclassified species of the families Flavobacteriaceae and Sphingomonadaceae. This bacterial community significantly decreased upon treatment with the supernatant from Alteromonas sp. Ni1-LEM, resulting in the prevalence of the genus Pseudoalteromonas. Furthermore, this bacterial supernatant significantly inhibited cell adhesion of seven benthic microalgae isolated from ROMs as well as promoting cell detachment of the existing microbial biofilms. The study showed that the extracellular supernatant modified the conformation of extracellular polymeric substances (EPS) in the biofouling of ROMs without any biocidal effects.     

The role of containerships as transfer mechanisms of marine biofouling species

Fouling of ships is an important historical and enduring transfer mechanism of marine nonindigenous species (NIS). Although containerships have risen to the forefront of global maritime shipping since the 1950s, few studies have directly sampled fouling communities on their submerged surfaces, and little is known about differences in the fouling characteristics among commercial ship types. Twenty-two in-service containerships at the Port of Oakland (San Francisco Bay, California) were sampled to test the hypothesis that the extent and taxonomic richness of fouling would be low on this type of ship, resulting from relatively fast speeds and short port durations. The data showed that the extent of macroorganisms (invertebrates and algae) was indeed low, especially across the large surface areas of the hull. Less than 1% of the exposed hull was colonized for all apart from one vessel. These ships had submerged surface areas of >7000 m², and fouling coverage on this area was estimated to be <l7 m² per vessel, with zero biota detected on the hulls of many vessels. The outlying smaller vessel (4465 m²) had an estimated coverage of 90% on the hull and also differed substantially from the other ships in terms of its recent voyage history, shorter voyage range and slower speeds. Despite the low extent of fouling, taxonomic richness was high among vessels. Consistent with recent studies, a wide range of organisms were concentrated at more protected and heterogeneous (non-hull) niche areas, including rudders, stern tubes and intake gratings. Green algae and barnacles were most frequently sampled among vessels, but hydroids, bryozoans, bivalves and ascidians were also recorded. One vessel had 20 different species in its fouling assemblage, including non-native species (already established in San Francisco Bay) and mobile species that were not detected in visual surveys. In contrast to other studies, dry dock block areas did not support many organisms, despite little antifouling deterrence in some cases. Comparisons with previous studies suggest that the accumulation of fouling on containerships may be lower than on other ship types (eg bulkers and general cargo vessels), but more data are needed to determine the hierarchy of factors contributing to differences in the extent of macrofouling and non-native species vector risks within the commercial fleet.     

Laboratory culture and evaluation of the tubeworm Ficopomatus enigmaticus for biofouling studies

Ficopomatus enigmaticus, a euryhaline tube-building polychaete worm with a subtropical to temperate distribution, is an increasingly problematic fouling organism. In this study, laboratory protocols for maintaining adult broodstock, destructive spawning, larval culture and a settlement bioassay were developed. The method routinely yielded approximately 200 larvae per spawning adult. The mean number of eggs released by females was 1517 and the mean number of spermatozoids per male was 4.425?×?10⁶. Fertilisation success, using an initial concentration of 2.5?×?10⁶ spermatozoids and 45?eggs?ml^?1, was 76% after a contact time of 60?min. The first cleavage occurred after 20?min and the trocophore larval stage was attained by 18?h. Metatrochophores were observed 4?d post-fertilisation and were competent to settle 1?day later. The proportion of larvae that settled after 48?h was surface-dependent: 10.24% on glass, 1.39% on polystyrene and 11.07% on a poly(dimethylsiloxane) elastomer. The presence of a biofilm on glass increased the rate of settlement 7-fold compared to clean glass.     

The impact and control of biofouling in marine aquaculture: a review

Biofouling in marine aquaculture is a specific problem where both the target culture species and/or infrastructure are exposed to a diverse array of fouling organisms, with significant production impacts. In shellfish aquaculture the key impact is the direct fouling of stock causing physical damage, mechanical interference, biological competition and environmental modification, while infrastructure is also impacted. In contrast, the key impact in finfish aquaculture is the fouling of infrastructure which restricts water exchange, increases disease risk and causes deformation of cages and structures. Consequently, the economic costs associated with biofouling control are substantial. Conservative estimates are consistently between 5–10% of production costs (equivalent to US$ 1.5 to 3 billion yr^?1), illustrating the need for effective mitigation methods and technologies. The control of biofouling in aquaculture is achieved through the avoidance of natural recruitment, physical removal and the use of antifoulants. However, the continued rise and expansion of the aquaculture industry and the increasingly stringent legislation for biocides in food production necessitates the development of innovative antifouling strategies. These must meet environmental, societal, and economic benchmarks while effectively preventing the settlement and growth of resilient multi-species consortia of biofouling organisms.     

The oceans are changing: impact of ocean warming and acidification on biofouling communities

Climate change (CC) is driving modification of the chemical and physical properties of estuaries and oceans with profound consequences for species and ecosystems. Numerous studies investigate CC effects from species to ecosystem levels, but little is known of the impacts on biofilm communities and on bioactive molecules such as cues, adhesives and enzymes. CC is induced by anthropogenic activity increasing greenhouse emissions leading to rises in air and water temperatures, ocean acidification, sea level rise and changes in ocean gyres and rainfall patterns. These environmental changes are resulting in alterations within marine communities and changes in species ranges and composition. This review provides insights and synthesis of knowledge about the effect of elevated temperature and ocean acidification on microfouling communities and bioactive molecules. The existing studies suggest that CC will impact production of bioactive compounds as well as the growth and composition of biofouling communities. Undoubtedly, with CC fouling management will became an even greater challenge.     

The effect of vibration frequency and amplitude on biofouling deterrence

The use of vibration is proposed as a means of controlling the settlement of marine fouling organisms. In this study, panels with embedded lead zirconate titanate, known as PZT, were placed in the field over 3?months. The panels were vibrated at different velocity levels at frequencies between 70 and 445?Hz. It was found that barnacles (Amphibalanus variegatus Darwin and Elminius sp.) were the only fouling organisms affected by the applied vibration, and these organisms settled in significantly lower numbers when the plates were excited at specific frequencies and amplitudes. Panels vibrating at relatively higher frequencies, greater than 260?Hz, exhibited reduced barnacle settlement, whilst lower frequencies in the 70–100?Hz range had little or no effect. The settlement of other fouling organisms such as tubeworms, bryozoans, ascidians and algae did not appear to be affected by the applied excitation. The experimental results showed that increasing the velocity amplitude of vibration was a contributing factor in inhibiting barnacle settlement.     

The biology of biofouling diatoms and their role in the development of microbial slimes

Diatoms are a major component of microbial slimes that develop on man-made surfaces placed in the marine environment. Toxic antifouling paints, as well as environmentally friendly, fouling-release coatings, tend to be effective against most fouling organisms, yet fail badly to diatom slimes. Biofouling diatoms have been found to tenaciously adhere to and colonise even the most resistant of artificial surfaces. This review covers the basic biology of fouling marine diatoms, their mechanisms of adhesion and the nature of their adhesives, as well as documenting the various approaches that have been utilised to understand the formation and maintenance of diatom biofouling layers.     

The adhesive strategies of cyprids and development of barnacle-resistant marine coatings

Over the last decade, approaches to the development of surfaces that perturb settlement and/or adhesion by barnacles have diversified substantially. Although, previously, coatings research focussed almost exclusively on biocidal technologies and low modulus, low surface-free-energy ‘fouling-release’ materials, novel strategies to control surface colonisation are now receiving significant attention. It is timely, therefore, to review the current ‘state of knowledge’ regarding fouling-resistant surface characteristics and their mechanisms of action against settling larvae of barnacles. The role of the barnacle in marine fouling is discussed here in the context of its life cycle and the behavioural ecology of its cypris larva. The temporary and permanent adhesion mechanisms of cyprids are covered in detail and an overview of adult barnacle adhesion is presented. Recent legislation has directed academic research firmly towards environmentally inert marine coatings, so the actions of traditional biocides on barnacles are not described here. Instead, the discussion is restricted to those surface modifications that interfere with settlement-site selection and adhesion of barnacle cypris larvae; specifically, textural engineering of surfaces, development of inert ‘non-fouling’ surfaces and the use of enzymes in antifouling.     

Effect of biofouling on anodized and sol-gel treated titanium surfaces: a comparative study

Anodization and sol-gel treatments of titanium (Ti) were evaluated as biofilm control measures on surfaces exposed to seawater exposed to ultraviolet light. Anodized and sol-gel treated specimens were characterized using Raman spectroscopy to confirm the presence of TiO₂. The single anatase phase was observed at the anodized surfaces whereas the anatase/rutile mixed phase was detected on the sol-gel coated surfaces. After exposure of the specimens to seawater, biofilms were characterized by total viable counts, and epifluorescence and Raman microscopy. These techniques confirmed the reduction in biofilm formation on both the anodized and sol-gel coated Ti specimens compared to the untreated specimens. Biofilm control by anodization was found to be more effective than by sol-gel treatment of the specimens. The higher particle size and the inhomogeneity at the sol-gel coated surfaces produced less effective biofilm control.     

Application of zinc oxide and sodium alginate for biofouling mitigation in a membrane bioreactor treating urban wastewater

Abstract

This research aimed to mitigate fouling in membrane bioreactors (MBR) through concurrent usage of zinc oxide as an antibacterial agent (A) and sodium alginate as a hydrophilic agent (H) within a polyacrylonitrile membrane (PM) structure. The antibacterial polymeric membranes (APM) and antibacterial hydrophilic polymeric membranes (AHPM) synthesized showed a higher porosity, mechanical strength and bacterial inhibition zone, and a lower contact angle in comparison with PM membranes. EDS, SEM and AFM analyses were used to characterize the chemical, structural, and morphological properties of PM, APM, and AHPM. The flux of PM, APM, and AHPM in MBR was 37, 48, and 51?l m^?2 h^?1 and COD removal was 81, 93.5, and 96.7%, respectively. After MBR operation for 35?days in an urban wastewater treatment, only 50% of the flux of PM was recovered, while the antibacterial and hydrophilic agents yielded a flux recovery of 72.7 and 100% for APM and AHPM, respectively.     

Developing an antibacterial super-hydrophilic barrier between bacteria and membranes to mitigate the severe impacts of biofouling

Biofouling produces concentrated microbial populations with highly resistive biofilms and is considered to be a serious obstacle for a wide range of membrane technology applications. An antibacterial super-hydrophilic barrier could help to reduce biofouling by preventing direct contact between membranes and bacteria. In this study, an antibacterial super-hydrophilic barrier consisting of a layer of TiO₂ nanoparticles (NPs) was developed on polyvinylidene fluoride (PVDF)-based membrane via a facile technique. The results demonstrated that the presence of TiO₂ NPs eliminated the first step of biofouling, ie bacterial adhesion to the membrane. In addition, after bacterial deposition onto the membrane during ultrafiltration (UF), the TiO₂ NPs significantly retarded bacterial growth and reproduction (the second step of biofouling). During UF, the membrane flux decreased due to bacterial deposition, but 85% of the flux was recovered through physical cleaning using water. This study sheds light on the potential advantages of antibacterial super-hydrophilic membranes for biofouling mitigation.