Measuring DNA damage using capillary electrophoresis with laser-induced fluorescence detection

Damage to cellular DNA is implicated in the early stages of carcinogenesis and in the cytotoxicity of many anticancer agents, including ionizing radiation. Sensitive techniques are required for measuring cellular levels of DNA damage. We describe in detail a novel immunoassay that makes use of the resolving power of capillary electrophoresis and the sensitivity of laser-induced fluorescence detection. An example is given of the detection of thymine glycol in DNA produced by irradiation of human cells with a clinical dose of 2 Gy. A detection limit of approximately 10(-21) mol allowed us to monitor the repair of the lesion and to suggest that the cellular repair response may be inducible.     

The theory of DNA separation by capillary electrophoresis

The Human Genome has been sequenced in large part owing to the invention of capillary electrophoresis. Although this technology has matured enough to allow such amazing achievements, the physical mechanisms at play during separation have yet to be completely understood and optimized. Recently, new separation regimes and new physical mechanisms have been investigated. The use of free-flow electrophoresis and new modes of pulsed-field electrophoresis have been suggested, while we have observed a shift towards single nucleotide polymorphism analysis and microchip technologies. A strong theoretical basis remains essential for the efficient development of new methods.     

Observation of DNA molecules undergoing capillary electrophoresis.

This paper presents a method to observe the motions and configurations of large DNA molecules undergoing capillary electrophoresis (CE). A simple device to perform CE horizontally under microscopic observation is designed and images of single DNA molecules inside the capillary are obtained using an epi-fluorescence microscope. DNA molecules moved towards the negative electrode when an electric field was applied. The mobilities of three types of DNA (T4 and lambda bacteriophage DNA and PBR322 plasmid DNA) were measured at different electric field strength. The mobility vs. electric field strength curves of these three large DNAs showed that the mobility remained constant at high electric field strength (200-600 Volt/cm) and increased significantly at low electric field strength (less than or equal to 50 Volt/cm.). The apparent mobilities of the large DNA molecules were independent of molecular weight. At electric field strengths greater than or equal to 400 Volt/cm., big aggregates (snowballs) of DNA molecules formed and moved upstream towards the positive electrode. When the field was turned off, the aggregates dissociated into a cloud of single DNA molecules, and diffused into the solution.     

DNA analysis by microfabricated capillary electrophoresis device.

The LIGA (Lithographie Galvanoformung Abformung) process using synchrotron radiation lithography is applied to the microfabrication of capillary array electrophoresis (CAE) device. Laser-induced fluorescence detection system for the CAE device has been constructed by the modification of laser confocal fluorescence microscopy. DNA molecules were detected during migrating in the microchannels filled with polymer separation matrices under electric field to optimize the separation conditions for DNA analysis. Based on this observation, we demonstrated that microfabricated CAE device is realized the fast separation of DNA.     

DNA annealing and DNA-protein interactions by capillary electrophoresis

This work deals with annealing of single-stranded DNA and the binding of a serum respond factor to a DNA probe containing specific binding site. Capillary electrophoresis (CE) method is explored and compared with the mobility-shift gel electrophoresis (GE) procedure. The results indicate the CE method offers direct and rapid annealing of the DNA strands. It requires no prior incubation with additives (polynucleotides, proteins) to reduce nonspecific DNA-protein interactions. Unwanted nonspecific interactions are not observed in the CE method. The presence of a fluorescein tag to the DNA probe yields identical results to those with the radioactive label. A fluorescein tag in the CE work can be used without any adverse effects. The dissociation constant (Kd) of this protein-DNA complex by the CE method was similar to those determined by the GE method (approximately 10(-6) M). The proposed method is extremely powerful, highly sensitive, quantitative, and fast. It can determine even very small conformational differences of the DNA probe.     

DNA sequencing by capillary electrophoresis (review)

DNA sequencing by capillary electrophoresis has been reviewed with an emphasis on progress during the last four years. The effects of sample purification, composition of sieving matrices, electric field strength, temperature, wall coating and DNA labeling on the DNA sequencing performance are discussed. Multicapillary array instrumentation is compared with one-capillary systems. Integrated systems that perform the whole DNA sequencing operation online starting from the DNA amplification through base calling and data processing are discussed.     

High speed DNA sequencing by capillary electrophoresis.

A major challenge of the Human Genome Initiative is the development of a rapid, accurate, and efficient DNA sequencing technology. A major limitation of current technology is the relatively long time required to perform the gel electrophoretic separations of DNA fragments produced in the sequencing reactions. We demonstrate here that it is possible to increase the speed of sequence analysis by over an order of magnitude by performing the electrophoresis and detection in ultra thin capillary gels. An instrument which utilizes these high speed separations to simultaneously analyze many samples will constitute a second generation automated DNA sequencer suitable for large-scale sequence analysis.     

Analysis of laser-induced plasmid DNA photolysis by capillary electrophoresis

Capillary electrophoresis (CE) was used to monitor the laser-induced conversion of supercoiled pKOL8UV5 plasmid DNA into nicked conformers. The plasmid samples (0.1 mg/ml) were incubated in the absence or presence of 110 μmol/l ethidium bromide (EB) and then exposed to 110 J of argon laser radiation (488 nm). The nicked, open circular conformers were separated from the supercoiled DNA by a 15% increase in retention time. Approximately 90% of the control DNA was in the supercoiled form. Laser radiation in the presence of EB caused complete conversion of the supercoiled plasmid DNA into nicked conformers. Laser-induced fluorescence CE (LIF-CE) was about 100-fold more sensitive than UV-CE in the detection of these conformers. Agarose gel electrophoresis confirmed these findings and showed the presence of the nicked plasmid conformers. Based on these comparisons, CE is an efficient analytical tool for the identification of laser-induced conformational changes in plasmid DNA.     

The use of capillary electrophoresis for DNA polymorphism analysis

Capillary electrophoresis has advanced enormously over the last 10 yr as a tool for DNA sequencing, driven by the human and other major genome projects and by the need for rapid electrophoresis-based DNA diagnostic tests. The common need of these analyses is a platform providing very high throughput, high-quality data, and low process costs. These demands have led to capillary electrophoresis machines with multiple capillaries providing highly parallel analyses, to new electrophoresis matrices, to highly sensitive spectrofluorometers, and to brighter, spectrally distinct fluorescent dyes with which to label DNA. Capillary devices have also been engineered onto microchip formats, on which both the amount of sample required for analysis and the speed of analysis are increased by an order of magnitude. This review examines the advances made in capillary and chip-based microdevices and in the different DNA-based assays developed for mutation detection and genotype analysis using capillary electrophoresis. The automation of attendant processes such as for DNA sample preparation, PCR, and analyte purification are also reviewed. Together, these technological developments provide the throughput demanded by the large genome-sequencing projects.     

DNA sequencing by capillary array electrophoresis with an electric field strength gradient

We examined the effect of an electric field strength gradient on DNA sequencing efficiency using capillary array electrophoresis. Several types of gradients were applied to DNA sequencing and tested in terms of read length and accuracy. Our original method improved the accuracy of DNA sequencing for longer fragments at high temperature.     

Rapid analysis of amplified double-stranded DNA by capillary electrophoresis with laser-induced fluorescence detection

DNA amplification technology has been applied to clinical diagnosis of infectious disease, genetic disorder, and cancer. After in vitro amplification of a particular DNA region, the methods of analysis for these amplified samples play a pivotal role in clinical diagnosis. Conventional gel electrophoresis has been routinely used in the lab for checking DNA. The whole procedure is time consuming and requires more than 1 ng of DNA for detection. To achieve greater performance in DNA diagnosis, we demonstrated capillary electrophoresis with laser induced fluorescence detection for analysis of amplified DNA. The analysis of DNA could be completed within 3 min and the data is directly entered into the computer. Considering the automatic and rapid process, we believe that this method could be routinely utilized for the clinical diagnosis of amplified DNA products.     

Improved single-strand DNA sizing accuracy in capillary electrophoresis.

Interpolation algorithms can be developed to size unknown single-stranded (ss) DNA fragments based on their electrophoretic mobilities, when they are compared with the mobilities of standard fragments of known sizes; however, sequence-specific anomalous electrophoretic migration can affect the accuracy and precision of the called sizes of the fragments. We used the anomalous migration of ssDNA fragments to optimize denaturation conditions for capillary electrophoresis. The capillary electrophoretic system uses a refillable polymer that both coats the capillary wall to suppress electro-osmotic flow and acts as the sieving matrix. The addition of 8 M urea to the polymer solution, as in slab gel electrophoresis, is insufficient to fully denature some anomalously migrating ssDNA fragments in this capillary electrophoresis system. The sizing accuracy of these fragments is significantly improved by the addition of 2-pyrrolidinone, or increased capillary temperature (60 degrees C). the effect of these two denaturing strategies is additive, and the best accuracy and precision in sizing results are obtained with a combination of chemical and thermal denaturation.     

Rapid detection of DNA sequence variants by conformation-sensitive capillary electrophoresis

The identification of novel sequence variants, which may be either disease-causing mutations or silent polymorphisms, in large numbers of samples is becoming the rate-limiting step in associating diseases with specific genes. This is particularly true in light of the imminent arrival of the complete reference sequence of the human genome. A number of techniques have been developed to analyze DNA samples for sequence variants rapidly. We describe a new technique, capillary-based conformation-sensitive gel electrophoresis (capillary CSGE) that transfers mutation detection from acrylamide gel to capillary electrophoresis. Capillary CSGE was able to detect 7/7 short insertion/deletions and 16/22 base substitutions in a series of random single-nucleotide polymorphisms and known variants in the lipoprotein lipase and BRCA2 genes. This technique has the potential to screen many megabases of DNA in a single day.     

On-line melting of double-stranded DNA for analysis of single-stranded DNA using capillary electrophoresis

Capillary electrophoresis (CE) is a convenient, fast and non-radioactive method with possibilities for automatization. To analyse single-stranded DNA molecules in a more automated way, we developed a heating device to melt double-stranded DNA fragments in the capillary during electrophoresis. In this study we used this device to obtain single-stranded DNA, necessary for the detection of point mutations in DNA using the single-strand conformation polymorphism technique. Results show that double-stranded DNA molecules can be melted on-line into single-stranded DNA molecules, although not for 100%. In an attempt to find universal electrophoretic conditions for the analysis of single-stranded DNA, we investigated the influence of several parameters on the yield of single-stranded DNA molecules and on the resolution of the single-stranded DNA peaks. We demonstrate that this heating device is a technical adjustment of CE which contributes to more automated analyses of DNA fragments.     

Measuring the translational diffusion coefficients of small DNA molecules by capillary electrophoresis

The apparent translational diffusion coefficients of four 20 base pair (bp) DNA oligonucleotides with different sequences have been measured by capillary electrophoresis, using the stopped migration method. The diffusion coefficients of the four oligomers were equal within experimental error, and averaged (120 +/- 10) x 10(-8) cm(2) s(-1) in 40 mM Tris-acetate-EDTA buffer at 25 degrees C. Since this value is nearly identical to the translational diffusion coefficient determined for a different 20-bp oligomer using other methods, the stopped migration method can accurately measure the diffusion coefficients of small DNA oligomers. The apparent diffusion coefficient of a 118-bp DNA restriction fragment was also measured by the stopped migration method. However, the observed value was approximately 25% larger than expected from other measurements, possibly because the diffusion coefficients of larger DNA molecules are somewhat dependent on the ionic strength of the solution.     

Method for phosphorothioate antisense DNA sequencing by capillary electrophoresis with UV detection.

The progress of antisense DNA therapy demands development of reliable and convenient methods for sequencing short single-stranded oligonucleotides. A method of phosphorothioate antisense DNA sequencing analysis using UV detection coupled to capillary electrophoresis (CE) has been developed based on a modified chain termination sequencing method. The proposed method reduces the sequencing cost since it uses affordable CE-UV instrumentation and requires no labeling with minimal sample processing before analysis. Cycle sequencing with ThermoSequenase generates quantities of sequencing products that are readily detectable by UV. Discrimination of undesired components from sequencing products in the reaction mixture, previously accomplished by fluorescent or radioactive labeling, is now achieved by bringing concentrations of undesired components below the UV detection range which yields a 'clean', well defined sequence. UV detection coupled with CE offers additional conveniences for sequencing since it can be accomplished with commercially available CE-UV equipment and is readily amenable to automation.     

Multiwavelength fluorescence detection for DNA sequencing using capillary electrophoresis.

Multiwavelength detection of laser induced fluorescence for dideoxynucleotide DNA sequencing with four different fluorophores and separation by capillary gel electrophoresis is described. A cryogenically cooled, low readout noise, 2-dimensional charge-coupled device is used as a detector for the on-line, on-column recording of emission spectra. The detection system has no moving parts and provides wavelength selectivity on a single detector device. The detection limit of fluorescently labeled oligonucleotides meets the high sensitivity requirements for capillary DNA sequencing largely due to the efficient operation of the CCD detector with a 94% duty cycle. Using the condition number as a selectivity criterion, multiwavelength detection provides better analytical selectivity than detection with four bandpass filters. Monte Carlo studies and analytical estimates show that base assignment errors are reduced with peak identification based on entire emission spectra. High-speed separation of sequencing samples and the treatment of the 2-dimensional electropherogram data is presented. Comparing the DNA sequence of a sample separated by slab gel electrophoresis with sequence from capillary gel electrophoresis and multiwavelength detection we find no significant difference in the amount of error attributable to the instrumentation.     

The mobility minima in pulsed-field capillary electrophoresis of large DNA.

Pulsed-field capillary electrophoresis represents a new tool for rapid and highly efficient separations of large biopolymers. The method has been utilized here to study dependencies of the electrophoretic mobility upon the frequency and pulse shape of applied voltage for large, double-stranded DNA molecules (5-100 kb) migrating in neutral polymer solutions. Two different shapes of alternating electric field (sine- and square-wave impulses) were examined with the frequency values ranging from 1 to 30 Hz. The linear dependence between duration of the forward pulse (at which the DNA molecule experiences a minimum mobility) and the product N.In(N) (where N is the number of base pairs) was experienced in field-inversion gel electrophoresis, while exponential dependence was found with the sinusoidal electric field. The mobility minima were lower in field-inversion electrophoresis than with the biased sinusoidal-field technique. The DNA (5 kb concatamers) was adequately separated using a ramp of frequency in the square-wave electric field, in approximately 1 h. The migration order of DNA fragments was referenced through adding a monodisperse DNA (48.5 kb) into the sample. The band inversion phenomena were not observed under any experimental conditions used in this work.     

DNA interaction with human serum albumin studied by affinity capillary electrophoresis and FTIR spectroscopy

The question addressed in this study is how does the protein-DNA complexation affect the structure and dynamics of DNA and protein in aqueous solution. We examined the interaction of calf-thymus DNA with human serum albumin (HSA) in aqueous solution at physiological conditions, using constant DNA concentration of 12.5 mM (phosphate) and various HSA contents 0.25 to 2% or 0.04 to 0.3 mM. Affinity capillary electrophoresis and FTIR spectroscopic methods were used to determine the protein binding mode, the association constant, sequence preference, and the biopolymer secondary structural changes in the HSA-DNA complexes. Spectroscopic evidence showed two types of HSA-DNA complexes with strong binding of K(1) = 4.5 x 10(5) M(-1) and weak binding of K(2) = 6.10 x 10(4) M(-1). The two major binding sites were located on the G-C bases and the backbone PO(2) group. The protein-DNA interaction stabilizes the HSA secondary structure. A minor alteration of B-DNA structure was observed, while no major protein conformational changes occurred.