An Advanced Separator for Li–O2 Batteries: Maximizing the Effect of Redox Mediators

Although Li–O₂ batteries are promising next‐generation energy storage systems with superior theoretical capacities, they have a serious limitation regarding the large overpotential upon charging that results from the low conductivity of the discharge product. Thus, various redox mediators (RMs) have been widely studied to reduce the overpotential in the charging process, which should promote the oxidation of Li₂O₂. However, RMs degrade the Li metal anode through a parasitic reaction between the RM and the Li metal, and a solution for this phenomenon is necessary. In this study, an effective method is proposed to prevent the migration of the RM toward the anode side of the lithium using a separator that is modified with a negatively charged polymer. When DMPZ (5,10‐dihydro‐5,10‐dimethylphenazine) is used as an RM, it is found that the modified separator suppresses the migration of DMPZ toward the counter electrode of the Li metal anode. This is investigated by a visual redox couple diffusion test, a morphological investigation, and an X‐ray diffraction study. This advanced separator effectively maximizes the catalytic activity of the redox mediator. Li–O₂ batteries using both a highly concentrated DMPZ and the modified separator exhibit improved performance and maintained 90% round‐trip efficiency up to the 20th cycle.     

Optimized Bicompartment Two Solution Cells for Effective and Stable Operation of Li–O2 Batteries

Lithium–oxygen batteries are in fact the only rechargeable batteries that can rival internal combustion engines, in terms of high energy density. However, they are still under development due to low‐efficiency and short lifetime issues. There are problems of side reactions on the cathode side, high reactivity of the Li anode with solution species, and consumption of redox mediators via reactions with metallic lithium. Therefore, efforts are made to protect/block the lithium metal anode in these cells, in order to mitigate side reactions. However, new approach is required in order to solve the problems mentioned above, especially the irreversible reactions of the redox mediators which are mandatory to these systems with the Li anode. Here, optimized bicompartment two solution cells are proposed, in which detrimental crossover between the cathode and anode is completely avoided. The Li metal anode is cycled in electrolyte solution containing fluorinated ethylene carbonate, in which its cycling efficiency is excellent. The cathode compartment contains ethereal solution with redox mediator that enables oxidation of Li₂O₂ at low potentials. The electrodes are separated by a solid electrolyte membrane, allowing free transport of Li ions. This approach increases cycle life of lithium oxygen cells and their energy efficiency.     

Structural and Electrochemical Study of Al2O3 and TiO2 Coated Li1.2Ni0.13Mn0.54Co0.13O2 Cathode Material Using ALD

Nanolayers of Al₂O₃ and TiO₂ coatings were applied to lithium‐ and manganese‐rich cathode powder Li_1.2Ni_0.13Mn_0.54Co_0.13O₂ using an atomic layer deposition (ALD) method. The ALD coatings exhibited different surface morphologies; the Al₂O₃ surface film appeared to be uniform and conformal, while the TiO₂ layers appeared as particulates across the material surface. In a Li‐cell, the Al₂O₃ surface film was stable during repeated charge and discharge, and this improved the cell cycling stability, despite a high surface impedance. The TiO₂ layer was found to be more reactive with Li and formed a Li_xTiO₂ interface, which led to a slight increase in cell capacity. However, the repetitive insertion/extraction process for the Li⁺ ions caused erosion of the surface protective TiO₂ film, which led to degradation in cell performance, particularly at high temperature. For cells comprised of the coated Li_1.2Ni_0.13Mn_0.54Co_0.13O₂ and an anode of meso‐carbon‐micro‐beads (MCMB), the cycling stability introduced by ALD was not enough to overcome the electrochemical instability of MCMB graphite. Therefore, protection of the cathode materials by ALD Al₂O₃ or TiO₂ can address some of the capacity fading issues related to the Li‐rich cathode at room temperature.     

A Pair of NiCo2O4 and V2O5 Nanowires Directly Grown on Carbon Fabric for Highly Bendable Lithium‐Ion Batteries

Mechanically bendable and flexible functionalities are urgently required for next‐generation battery systems that will be included in soft and wearable electronics, active sportswear, and origami‐based deployable space structures. However, it is very difficult to synthesize anode and cathode electrodes that have high energy density and structural reliability under large bending deformation. Here, vanadium oxide (V₂O₅) and nickel cobalt oxide (NiCo₂O₄) nanowire‐carbon fabric electrodes for highly flexible and bendable lithium ion batteries are reported. The vanadium oxide and nickel cobalt oxide nanowires were directly grown on plasma‐treated carbon fabric and were used as cathode and anode electrodes in a full cell lithium ion battery. Most importantly, a pre‐lithiation process was added to the nickel cobalt oxide nanowire anode to facilitate the construction of a full cell using symmetrically‐architectured nanowire‐carbon fabric electrodes. The highly bendable full cell based on poly(ethylene oxide) polymer electrolyte and room temperature ionic liquid shows high energy density of 364.2 Wh kg^?1 at power density of 240 W kg^?1, without significant performance degradation even under large bending deformations. These results show that vanadium oxide and lithiated nickel cobalt oxide nanowire‐carbon fabrics are a good combination for binder‐free electrodes in highly flexible lithium‐ion batteries.     

Surface Mn Oxidation State Controlled Spinel LiMn2O4 as a Cathode Material for High‐Energy Li‐Ion Batteries

Spinel lithium manganese oxide (LiMn₂O₄) has attracted much attention as a promising cathode material for large‐scale lithium ion batteries. However, its continuous capacity fading at elevated temperature is an obstacle to extended cycling in large‐scale applications. Here, surface Mn oxidation state controlled LiMn₂O₄ is synthesized by coating stoichiometric LiMn₂O₄ with a cobalt‐substituted spinel, for which stoichiometric LiMn₂O₄ is used as the starting material and onto which a Li_xMn_yCo_zO₄ layer is coated from an acetate‐based precursor solution. In the coated material, the concentrations of both cobalt and Mn⁴⁺ ions vary from the surface to the core. the former without any lattice mismatch between the coating layer and host material. Cycle tests are performed under severe conditions, namely, high temperature and intermittent high current load. During the first discharge cycle at 7 C and 60 °C, a high energy and power density are measured for the coated material, 419 and 3.16 Wh kg^?1, respectively, compared with 343 and 3.03 Wh kg^?1, respectively, for the bare material. After 65 cycles under severe conditions, the coated material retains 82% and ≈100% of the initial energy and power density, respectively, whereas the bare material retains only ≈68% and ≈97% thereof.     

Reducing Capacity and Voltage Decay of Co‐Free Li1.2Ni0.2Mn0.6O2 as Positive Electrode Material for Lithium Batteries Employing an Ionic Liquid‐Based Electrolyte

Lithium‐rich layered oxides (LRLOs) exhibit specific capacities above 250 mAh g^?1, i.e., higher than any of the commercially employed lithium‐ion‐positive electrode materials. Such high capacities result in high specific energies, meeting the tough requirements for electric vehicle applications. However, LRLOs generally suffer from severe capacity and voltage fading, originating from undesired structural transformations during cycling. Herein, the eco‐friendly, cobalt‐free Li_1.2Ni_0.2Mn_0.6O₂ (LRNM), offering a specific energy above 800 Wh kg^?1 at 0.1 C, is investigated in combination with a lithium metal anode and a room temperature ionic liquid‐based electrolyte, i.e., lithium bis(trifluoromethanesulfonyl)imide and N‐butyl‐N‐methylpyrrolidinium bis(fluorosulfonyl)imide. As evidenced by electrochemical performance and high‐resolution transmission electron microscopy, X‐ray photoelectron spectroscopy, and online differential electrochemical mass spectrometry characterization, this electrolyte is capable of suppressing the structural transformation of the positive electrode material, resulting in enhanced cycling stability compared to conventional carbonate‐based electrolytes. Practically, the capacity and voltage fading are significantly limited to only 19% and 3% (i.e., lower than 0.2 mV per cycle), respectively, after 500 cycles. Finally, the beneficial effect of the ionic liquid‐based electrolyte is validated in lithium‐ion cells employing LRNM and Li₄Ti₅O₁₂. These cells achieve a promising capacity retention of 80% after 500 cycles at 1 C.     

Facile Synthesis of a 3D Nanoarchitectured Li4Ti5O12 Electrode for Ultrafast Energy Storage

Despite enormous efforts devoted to the development of high‐performance batteries, the obtainable energy and power density, durability, and affordability of the existing batteries are still inadequate for many applications. Here, a self‐standing nanostructured electrode with ultrafast cycling capability is reported by in situ tailoring Li₄Ti₅O₁₂ nanocrystals into a 3D carbon current collector (derived from filter paper) through a facile wet chemical process involving adsorption of titanium source, boiling treatment, and subsequent chemical lithiation. This 3D architectural electrode is charged/discharged to ≈60% of the theoretical capacity of Li₄Ti₅O₁₂ in ≈21 s at 100 C rate (17 500 mA g^?1 ), which also shows stable cycling performance for 1000 cycles at a cycling rate of 50 C. Additionally, modified 3D carbon current collector with much smaller pores and finer fiber diameters are further used, which significantly improve the specific capacity based on the weight of the entire electrode. These novel electrodes are promising for high‐power applications such as electric vehicles and smart grids. This unique electrode architecture also simplifies the electrode fabrication process and significantly enhances current collection efficiency (especially at high rate). Further, the conceptual electrode design is applicable to other oxide electrode materials for high‐performance batteries, fuel cells, and supercapacitors.     

Hierarchical Porous Carbonized Co3O4 Inverse Opals via Combined Block Copolymer and Colloid Templating as Bifunctional Electrocatalysts in Li–O2 Battery

Hierarchically organized porous carbonized‐Co₃O₄ inverse opal nanostructures (C‐Co₃O₄ IO) are synthesized via complementary colloid and block copolymer self‐assembly, where the triblock copolymer Pluronic P123 acts as the template and the carbon source. These highly ordered porous inverse opal nanostructures with high surface area display synergistic properties of high energy density and promising bifunctional electrocatalytic activity toward both the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). It is found that the as‐made C‐Co₃O₄ IO/Ketjen Black (KB) composite exhibits remarkably enhanced electrochemical performance, such as increased specific capacity (increase from 3591 to 6959 mA h g^?1), lower charge overpotential (by 284.4 mV), lower discharge overpotential (by 19.0 mV), and enhanced cyclability (about nine times higher than KB in charge cyclability) in Li–O₂ battery. An overall agreement is found with both C‐Co₃O₄ IO/KB and Co₃O₄ IO/KB in ORR and OER half‐cell tests using a rotating disk electrode. This enhanced catalytic performance is attributed to the porous structure with highly dispersed carbon moiety intact with the host Co₃O₄ catalyst.     

Optimized Concentration of Redox Mediator and Surface Protection of Li Metal for Maintenance of High Energy Efficiency in Li–O2 Batteries

Recently, various approaches for adding redox mediators to electrolytes and introducing protective layers onto Li metal have been suggested to overcome the low energy efficiency and poor cycle life of Li–O₂ batteries. However, the catalytic effect of the redox mediator for oxygen evolution gradually deteriorates during repeated cycling owing to its decomposition at the surfaces of both the oxygen electrode (cathode) and the Li metal electrode (anode). Here, optimized Li–O₂ batteries are designed with a continuously effective redox mediator and a stable protective layer for the Li metal electrode by optimizing the LiBr concentration and introducing a graphene–polydopamine composite layer, respectively. These synergistic modifications lead to a reduction of the charge potential to below 3.4 V and significantly improve the stability and cycle life of Li–O₂ batteries. Consequently, a high energy efficiency of above 80% is maintained over 150 cycles. Herein, it is confirmed that the relationships between all the battery materials should be understood in order to improve the performance of Li–O₂ batteries.     

Carbon Coated ZnFe2O4 Nanoparticles for Advanced Lithium‐Ion Anodes

The preparation and electrochemical characterization of a new material consisting of carbon coated ZnFe₂O₄ nanoparticles is presented. This material, which offers an interesting combination of alloying and conversion mechanisms, is capable of hosting up to nine equivalents of lithium per unit formula, corresponding to an exceptional specific capacity, higher than 1000 mAh g^?1. Composite electrodes of such a material, prepared using environmentally friendly sodium carboxymethyl cellulose as binder, showed the highest, ever reported, specific capacity and high rate performance upon long‐term testing. Furthermore, in situ X‐ray diffraction analysis allowed identifying the reduction process occurring upon initial lithiation.     

An Open‐Structured Matrix as Oxygen Cathode with High Catalytic Activity and Large Li2O2 Accommodations for Lithium–Oxygen Batteries

The nonaqueous lithium–oxygen (Li–O₂) battery is considered as one of the most promising candidates for next‐generation energy storage systems because of its very high theoretical energy density. However, its development is severely hindered by large overpotential and limited capacity, far less than theory, caused by sluggish oxygen redox kinetics, pore clogging by solid Li₂O₂ deposition, inferior Li₂O₂/cathode contact interface, and difficult oxygen transport. Herein, an open‐structured Co₉S₈ matrix with sisal morphology is reported for the first time as an oxygen cathode for Li–O₂ batteries, in which the catalyzing for oxygen redox, good Li₂O₂/cathode contact interface, favorable oxygen evolution, and a promising Li₂O₂ storage matrix are successfully achieved simultaneously, leading to a significant improvement in the electrochemical performance of Li–O₂ batteries. The intrinsic oxygen‐affinity revealed by density functional theory calculations and superior bifunctional catalytic properties of Co₉S₈ electrode are found to play an important role in the remarkable enhancement in specific capacity and round‐trip efficiency for Li–O₂ batteries. As expected, the Co₉S₈ electrode can deliver a high discharge capacity of ≈6875 mA h g^?1 at 50 mA g^?1 and exhibit a low overpotential of 0.57 V under a cutoff capacity of 1000 mA h g^?1, outperforming most of the current metal‐oxide‐based cathodes.     

Calpain-mediated truncation of dihydropyrimidinase-like 3 protein (DPYSL3) in response to NMDA and H2O2 toxicity

Dihydropyrimidinase-like protein 3 (DPYSL3), a member of TUC (TOAD-64/Ulip/CRMP), is believed to play a role in neuronal differentiation, axonal outgrowth and, possibly, neuronal regeneration. In primary cortical cultures, glutamate (NMDA) excitotoxicity and oxidative stress (H2O2) caused the cleavage of DPYSL3, resulting in the appearance of a doublet of 62 kDa and 60 kDa. Pre-treatment of cell cultures with calpain inhibitors, but not caspase 3 inhibitor, before exposure to NMDA or H2O2 completely blocked the appearance of the doublet, suggesting calpain-mediated truncation. Furthermore, in vitro digestion of DPYSL3 in cell lysate with purified calpain revealed a cleavage product identical to that observed in NMDA- and H2O2-treated cells, and its appearance was blocked by calpain inhibitors. Analysis of the DPYSL3 protein sequence revealed a possible cleavage site for calpain (Val-Arg-Ser) on the C-terminus of DPYSL3. Collectively, these studies demonstrate for the first time that DPYSL3 is a calpain substrate. The physiological relevance of the truncated DPYSL3 protein remains to be determined.     

Light‐Driven BiVO4–C Fuel Cell with Simultaneous Production of H2O2

Photoelectrochemical (PEC) systems have been researched for decades due to their great promise to convert sunlight to fuels. The majority of the research on PEC has been using light to split water to hydrogen and oxygen, and its performance is limited by the need of additional bias. Another research direction on PEC using light, is to decompose organic materials while producing electricity. In this work, the authors report a new type of unassisted PEC system that uses light, water and oxygen to simultaneously produce electricity and hydrogen peroxide (H₂O₂) on both the photoanode and cathode, which is essentially a light‐driven fuel cell with H₂O₂ as the main product at the two electrodes, meanwhile achieving a maximum power density of 0.194 mW cm^‐2, an open circuit voltage of 0.61 V, and a short circuit current density of 1.09 mA cm^‐2. The electricity output can be further used as a sign for cell function when accompanied by a detector such as a light‐emitting diode (LED) light or a multimeter. This is the first work that shows H₂O₂ two‐side generation with a strict key factors study of the system, with a clear demonstration of electricity output ability using low‐cost earth abundant materials on both sides, which represents an exciting new direction for PEC systems.     

NADPH oxidase is involved in H2O2-induced differentiation of human promyelocytic leukaemia HL-60 cells

The expression and activity of NADPH oxidase increase when HL‐60 cells are induced into terminally differentiated cells. However, the function of NADPH oxidase in differentiation is not well elucidated. With 150–500 μM H₂O₂ inducing differentiation of HL‐60 cells, we measured phagocytosis of latex beads and investigated cell electrophoresis. Two inhibitors of NADPH oxidase, DPI (diphenyleneiodonium) and APO (apocynin), blocked the differentiation potential of cells induced by 200 μM H₂O₂. However, H₂O₂ stimulated the generation of intracellular superoxide (O₂ ^{? ?}), which decreased in the presence of the two inhibitors. DPI also inhibited H₂O₂‐induced ERK (extracellular‐signal‐regulated kinase) activation, as detected by Western blotting. Furthermore, PD98059, the inhibitor of the ERK pathway, inhibited the differentiation of HL‐60 cells induced by H₂O₂. This shows that H₂O₂ can activate NADPH oxidase, leading to O₂ ^{? ?} production, followed by ERK activation and ultimately resulting in the differentiation of HL‐60 cells. The data indicate that NADPH oxidase is an important cell signal regulating cell differentiation.     

Hierarchically Porous,Ultrathick, “Breathable” Wood‐Derived Cathode for Lithium‐Oxygen Batteries

In this work, a hierarchically porous and ultrathick “breathable” wood‐based cathode for high‐performance Li‐O₂ batteries is developed. The 3D carbon matrix obtained from the carbonized and activated wood (denoted as CA‐wood) serves as a superconductive current collector and an ideal porous host for accommodating catalysts. The ruthenium (Ru) nanoparticles are uniformly anchored on the porous wall of the aligned microchannels (denoted as CA‐wood/Ru). The aligned open microchannels inside the carbon matrix contribute to unimpeded oxygen gas diffusion. Moreover, the hierarchical pores on the microchannel walls can be facilely impregnated by electrolyte, forming a continuous supply of electrolyte. As a result, numerous ideal triphase active sites are formed where electrolyte, oxygen, and catalyst accumulate on the porous walls of microchannels. Benefiting from the numerous well‐balanced triple‐phase active sites, the assembled Li‐O₂ battery with the CA‐wood/Ru cathode (thickness: ≈700 µm) shows a high specific area capacity of 8.58 mA h cm^?2 at 0.1 mA cm^?2. Moreover, the areal capacity can be further increased to 56.0 mA h cm^?2 by using an ultrathick CA‐wood/Ru cathode with a thickness of ≈3.4 mm. The facile ultrathick wood‐based cathodes can be applied to other cathodes to achieve a super high areal capacity without sacrificing the electrochemical performance.     

V2O5 Nano‐Electrodes with High Power and Energy Densities for Thin Film Li‐Ion Batteries

Nanostructured V₂O₅ thin films have been prepared by means of cathodic deposition from an aqueous solution made from V₂O₅ and H₂O₂ directly on fluorine‐doped tin oxide coated (FTO) glasses followed by annealing at 500°C in air, and studied as film electrodes for lithium ion batteries. XPS results show that the as‐deposited films contained 15% V⁴⁺, however after annealing all the vanadium is oxidized to V⁵⁺. The crystallinity, surface morphology, and microstructures of the films have been investigated by means of XRD, SEM, and AFM. The V₂O₅ thin film electrodes show excellent electrochemical properties as cathodes for lithium ion intercalation: a high initial discharge capacity of 402 mA h g^?1 and 240 mA h g^?1 is retained after over 200 cycles with a discharging rate of 200 mA g^?1 (1.3 C). The specific energy density is calculated as 900 W h kg^?1 for the 1^st cycle and 723 W h kg^?1 for the 180^th cycle when the films are tested at 200 mA g^?1 (1.3 C). When discharge/charge is carried out at a high current density of 10.5 A g^?1 (70 C), the thin film electrodes retain a good discharge capacity of 120 mA h g^?1, and the specific power density is over 28 kW kg^?1.