Interplay Between Side Chain Pattern,Polymer Aggregation,and Charge Carrier Dynamics in PBDTTPD:PCBM Bulk‐Heterojunction Solar Cells

Poly(benzo[1,2‐b:4,5‐b′]dithiophene–alt–thieno[3,4‐c]pyrrole‐4,6‐dione) (PBDTTPD) polymer donors with linear side‐chains yield bulk‐heterojunction (BHJ) solar cell power conversion efficiencies (PCEs) of about 4% with phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as the acceptor, while a PBDTTPD polymer with a combination of branched and linear substituents yields a doubling of the PCE to 8%. Using transient optical spectroscopy it is shown that while the exciton dissociation and ultrafast charge generation steps are not strongly affected by the side chain modifications, the polymer with branched side chains exhibits a decreased rate of nongeminate recombination and a lower fraction of sub‐nanosecond geminate recombination. In turn the yield of long‐lived charge carriers increases, resulting in a 33% increase in short circuit current (J _sc). In parallel, the two polymers show distinct grazing incidence X‐ray scattering spectra indicative of the presence of stacks with different orientation patterns in optimized thin‐film BHJ devices. Independent of the packing pattern the spectroscopic data also reveals the existence of polymer aggregates in the pristine polymer films as well as in both blends which trap excitons and hinder their dissociation.     

Molecular Understanding of the Open‐Circuit Voltage of Polymer:Fullerene Solar Cells

The origin of open‐circuit voltage (V_OC) was studied for polymer solar cells based on a blend of poly(3‐hexylthiophene) (P3HT) and seven fullerene derivatives with different LUMO energy levels and side chains. The temperature dependence of J–V characteristics was analyzed by an equivalent circuit model. As a result, V_OC increased with the decrease in the saturation current density J₀ of the device. Furthermore, J₀ was dependent on the activation energy E_A for J₀, which is related to the HOMO–LUMO energy gap between P3HT and fullerene. Interestingly, the pre‐exponential term J₀₀ for J₀ was larger for pristine fullerenes than for substituted fullerene derivatives, suggesting that the electronic coupling between molecules also has substantial impact on V_OC. This is probably because the recombination is non‐diffusion‐lmilited reaction depending on electron transfer at the P3HT/fullerene interface. In summary, the origin of V_OC is ascribed not only to the relative HOMO–LUMO energy gap but also to the electronic couplings between fullerene/fullerene and polymer/fullerene.     

Effect of Alkylsilyl Side‐Chain Structure on Photovoltaic Properties of Conjugated Polymer Donors

Side‐chain engineering is an important strategy for optimizing photovoltaic properties of organic photovoltaic materials. In this work, the effect of alkylsilyl side‐chain structure on the photovoltaic properties of medium bandgap conjugated polymer donors is studied by synthesizing four new polymers J70 , J72 , J73 , and J74 on the basis of highly efficient polymer donor J71 by changing alkyl substituents of the alkylsilyl side chains of the polymers. And the photovoltaic properties of the five polymers are studied by fabricating polymer solar cells (PSCs) with the polymers as donor and an n‐type organic semiconductor (n‐OS) m‐ITIC as acceptor. It is found that the shorter and linear alkylsilyl side chain could afford ordered molecular packing, stronger absorption coefficient, higher charge carrier mobility, thus results in higher J_sc and fill factor values in the corresponding PSCs. While the polymers with longer or branched alkyl substituents in the trialkylsilyl group show lower‐lying highest occupied molecular orbital energy levels which leads to higher V_oc of the PSCs. The PSCs based on J70 :m‐ITIC and J71 :m‐ITIC achieve power conversion efficiency (PCE) of 11.62 and 12.05%, respectively, which are among the top values of the PSCs reported in the literatures so far.     

Effect of Molecular Orientation of Donor Polymers on Charge Generation and Photovoltaic Properties in Bulk Heterojunction All‐Polymer Solar Cells

All‐polymer solar cells (all‐PSCs) utilizing p‐type polymers as electron‐donors and n ‐typepolymers as electron‐acceptors have attracted a great deal of attention, and their efficiencies have been improved considerably. Here, five polymer donors with different molecular orientations are synthesized by random copolymerization of 5‐fluoro‐2,1,3‐benzothiadiazole with different relative amounts of 2,2′‐bithiophene (2T) and dithieno[3,2‐b;2′,3′‐d]thiophene (DTT). Solar cells are prepared by blending the polymer donors with a naphthalene diimide‐based polymer acceptor (PNDI) or a [6,6]‐phenyl C₇₁‐butyric acid methyl ester (PC₇₁BM) acceptor and their morphologies and crystallinity as well as optoelectronic, charge‐transport and photovoltaic properties are studied. Interestingly, charge generation in the solar cells is found to show higher dependence on the crystal orientation of the donor polymer for the PNDI‐based all‐PSCs than for the conventional PC₇₁BM‐based PSCs. As the population of face‐on‐oriented crystallites of the donor increased in PNDI‐based PSC, the short‐circuit current density (J_SC) and external quantum efficiency of the devices are found to significantly improve. Consequently, device efficiency was enhanced of all‐PSC from 3.11% to 6.01%. The study reveals that producing the same crystal orientation between the polymer donor and acceptor (face‐on/face‐on) is important in all‐PSCs because they provide efficient charge transfer at the donor/acceptor interface.     

The Introduction of Fluorine and Sulfur Atoms into Benzotriazole‐Based p‐Type Polymers to Match with a Benzotriazole‐Containing n‐Type Small Molecule: “The Same‐Acceptor‐Strategy” to Realize High Open‐Circuit Voltage

“The Same‐Acceptor‐Strategy” (SAS) adopts benzotriazole (BTA)‐based p‐type polymers paired with a new BTA based non‐fullerene acceptor BTA13 to minimize the trade‐off between the open‐circuit voltage (V_OC) and short circuit current (J_SC). The fluorination and sulfuration are introduced to lower the highest occupied molecular orbitals (HOMO) of the polymers. The fluorinated polymer of J52‐F shows the higher power conversion efficiency (PCE) of 8.36% than the analog polymer of J52, benefited from a good balance between an improved V_OC of 1.18 V and a J_SC of 11.55 mA cm^?2. Further adding alkylthio groups on J52‐F, the resulted polymer, J52‐FS, exhibits the highest V_OC of 1.24 V with a decreased energy loss of 0.48 eV, compared with 0.67 eV for J52 and 0.54 eV for J52‐F. However, J52‐FS shows an inferior PCE (3.84%) with a lower J_SC of 6.74 mA cm^?2, because the small ΔE_HOMO between J52‐FS and BTA13 (0.02 eV) gives rise to the inefficient hole transfer and high charge recombination, as well as low carrier mobilities. The results of this study clearly demonstrate that the introduction of different atoms in p‐type polymers is effective to improve the SAS and realize the high (V_OC) and PCE.     

Design of Cyanovinylene‐Containing Polymer Acceptors with Large Dipole Moment Change for Efficient Charge Generation in High‐Performance All‐Polymer Solar Cells

Designing polymers that facilitate exciton dissociation and charge transport is critical for the production of highly efficient all‐polymer solar cells (all‐PSCs). Here, the development of a new class of high‐performance naphthalenediimide (NDI)‐based polymers with large dipole moment change (Δµ_ge) and delocalized lowest unoccupied molecular orbital (LUMO) as electron acceptors for all‐PSCs is reported. A series of NDI‐based copolymers incorporating electron‐withdrawing cyanovinylene groups into the backbone (PNDITCVT‐R) is designed and synthesized with 2‐hexyldecyl (R = HD) and 2‐octyldodecyl (R = OD) side chains. Density functional theory calculations reveal an enhancement in Δµ_ge and delocalization of the LUMO upon the incorporation of cyanovinylene groups. All‐PSCs fabricated from these new NDI‐based polymer acceptors exhibit outstanding power conversion efficiencies (7.4%) and high fill factors (65%), which is attributed to efficient exciton dissociation, well‐balanced charge transport, and suppressed monomolecular recombination. Morphological studies by grazing X‐ray scattering and resonant soft X‐ray scattering measurements show the blend films containing polymer donor and PNDITCVT‐R acceptors to exhibit favorable face‐on orientation and well‐mixed morphology with small domain spacing (30–40 nm).     

Photodegradation in Encapsulated Silole‐Based Polymer: PCBM Solar Cells Investigated using Transient Absorption Spectroscopy and Charge Extraction Measurements

Light induced degradation has been observed in the performance of organic solar cells in the absence of oxygen and a detailed analysis of the effect of this photodegradation on optical and electrical features has been accomplished. This photodegradation study has been performed on encapsulated photovoltaic blend devices comprised of the silole‐based donor–acceptor polymer KP115 blended with [6,6]‐phenyl C61‐butyric acid methyl ester (PCBM). Photodegradation induces an almost 20% decrease in power conversion efficiency, primarily as a result of a reduction in short circuit current, J_SC. The initial burn‐in phase of the photodegradation has been examined using a combination of transient absorption spectroscopy and charge extraction measurements, including photo‐CELIV (charge extraction by linearly increasing voltage) and time‐resolved charge extraction using a nanosecond switch. These measurements reveal a bimodal KP115 polaron population, comprised of both delocalised and localised/trapped charge carriers. The photodegradation results are consistent with an alteration of this bimodal KP115 polaron population, with the polarons becoming trapped in a broader, deeper density of localised states. Under laser illumination and at open circuit conditions, this enhanced trapping after light soaking inhibits charges from undergoing bimolecular recombination, leading to higher extracted charge densities at long times. At the lower charge densities operating at short circuit conditions and under continuous white light illumination, where bimolecular recombination is much less significant, the J_SC decreases after light soaking due to a reduction in the efficiency of trapped charge carrier extraction.     

Donor‐Acceptor Interfacial Interactions Dominate Device Performance in Hybrid P3HT‐ZnO Nanowire‐Array Solar Cells

The adsorption of self‐assembled monolayers (SAMs) on metal oxide surfaces is a promising route to control electronic characteristics and surface wettability. Here, arylphosphonic acid derivatives are used to modulate the surface properties of vertically oriented ZnO nanowire arrays. Arylphosphonate‐functionalized ZnO nanowires are incorporated into hybrid organic‐inorganic solar cells in which infiltrated poly(3‐hexylthiophene) (P3HT) serves as the polymer donor. Strong correlations between device short‐circuit current density (J _sc) and power conversion efficiencies (PCEs) with ZnO surface functionalization species are observed and a weak correlation in the open‐circuit voltage (V _oc) is observed. Inverted solar cells fabricated with these treated interfaces exhibit PCEs as high as 2.1%, primarily due to improvements in J _sc. Analogous devices using untreated ZnO arrays having efficiencies of 1.6%. The enhancement in J _sc is attributed to surface passivation of ZnO by SAMs and enhanced wettability from P3HT, which improve charge transfer and reduce carrier recombination at the organic‐inorganic interface in the solar cells.     

Steric Engineering of Alkylthiolation Side Chains to Finely Tune Miscibility in Nonfullerene Polymer Solar Cells

Morphology and miscibility control are still a great challenge in polymer solar cells. Despite physical tools being applied, chemical strategies are still limited and complex. To finely tune blend miscibility to obtain optimized morphology, chemical steric engineering is proposed to systemically investigate its effects on optical and electronic properties, especially on a balance between crystallinity and miscibility. By changing the alkylthiol side chain orientation different steric effects are realized in three different polymers. Surprisingly, the photovoltaic device of the polymer PTBB‐m with middle steric structure affords a better power conversion efficiency, over 12%, compared to those of the polymers PTBB‐o and PTBB‐p with large or small steric structures, which could be attributed to a more balanced blend miscibility without sacrificing charge‐carrier transport. Space charge‐limited current, atomic force microscopy, grazing incidence wide angle X‐ray scattering, and resonant soft X‐ray scattering measurements show that the steric engineering of alkylthiol side chains can have significant impacts on polymer aggregation properties, blend miscibility, and photovoltaic performances. More important, the control of miscibility via the simple chemical approach has preliminarily proved its great potential and will pave a new avenue for optimizing the blend morphology.     

Investigation of Charge Carrier Behavior in High Performance Ternary Blend Polymer Solar Cells

This study demonstrates high‐performance, ternary‐blend polymer solar cells by modifying a binary blend bulk heterojunction (PPDT2FBT:PC₇₁BM) with the addition of a ternary component, PPDT2CNBT. PPDT2CNBT is designed to have complementary absorption and deeper frontier energy levels compared to PPDT2FBT, while being based on the same polymeric backbone. A power conversion efficiency of 9.46% is achieved via improvements in both short‐circuit current density (J_SC) and open‐circuit voltage (V_OC). Interestingly, the V_OC increases with increasing the PPDT2CNBT content in ternary blends. In‐depth studies using ultraviolet photoelectron spectroscopy and transient absorption spectroscopy indicate that the two polymers are not electronically homogeneous and function as discrete light harvesting species. The structural similarity between PPDT2CNBT and PPDT2FBT allows the merits of a ternary system to be fully utilized to enhance both J_SC and V_OC without detriment to fill‐factor via minimized disruption of semi‐crystalline morphology of binary PPDT2FBT:PC₇₁BM blend. Further, by careful analysis, charge carrier transport in this ternary blend is clearly verified to follow parallel‐like behavior.     

High‐Performance Wide Bandgap Copolymers Using an EDOT Modified Benzodithiophene Donor Block with 10.11% Efficiency

Newly developed benzo[1,2‐b:4,5‐b′]dithiophene (BDT) block with 3,4‐ethylenedioxythiophene (EDOT) side chains is first employed to build efficient photovoltaic copolymers. The resulting copolymers, PBDTEDOT‐BT and PBDTEDOTFBT, have a large bandgap more than 1.80 eV, which is attributed to the increased steric hindrance between the BDT and EDOT skeletons. Both copolymers possess the satisfied absorptions, low‐lying highest occupied molecular orbital (HOMO) levels and high crystallinity. Using the fluorination strategy, PBDTEDOT‐FBT exhibits a wider and stronger absorption and a deeper HOMO level than those of PBDTEDOT‐BT. PBDTEDOT‐FBT:[6,6]‐Phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) blend also shows the higher hole mobility and better surface morphology compared with the PBDTEDOTBT:PC₇₁BM blend. Combination of above advantages, PBDTEDOT‐FBT devices exhibit much higher power conversion efficiency (PCE) of 10.11%, with an improved open circuit voltage (V_oc) of 0.86 V, short circuit current densities (J_sc) of 16.01 mA cm^?2, and fill factor (FF) of 72.6%. This work not only provides a newly efficient candidate of BDT donor block modified with EDOT conjugated side chains, but also achieves high‐performance large bandgap copolymers for polymer solar cells (PSCs) via the synergistic effect of fluorination and side chain engineering strategies.     

Mixed Domains Enhance Charge Generation and Extraction in Bulk‐Heterojunction Solar Cells with Small‐Molecule Donors

The interplay between nanomorphology and efficiency of polymer‐fullerene bulk‐heterojunction (BHJ) solar cells has been the subject of intense research, but the generality of these concepts for small‐molecule (SM) BHJs remains unclear. Here, the relation between performance; charge generation, recombination, and extraction dynamics; and nanomorphology achievable with two SM donors benzo[1,2‐b:4,5‐b]dithiophene‐pyrido[3,4‐b]‐pyrazine BDT(PPTh₂)₂, namely SM1 and SM2, differing by their side‐chains, are examined as a function of solution additive composition. The results show that the additive 1,8‐diiodooctane acts as a plasticizer in the blends, increases domain size, and promotes ordering/crystallinity. Surprisingly, the system with high domain purity (SM1) exhibits both poor exciton harvesting and severe charge trapping, alleviated only slightly with increased crystallinity. In contrast, the system consisting of mixed domains and lower crystallinity (SM2) shows both excellent exciton harvesting and low charge recombination losses. Importantly, the onset of large, pure crystallites in the latter (SM2) system reduces efficiency, pointing to possible differences in the ideal morphologies for SM‐based BHJ solar cells compared with polymer‐fullerene devices. In polymer‐based systems, tie chains between pure polymer crystals establish a continuous charge transport network, whereas SM‐based active layers may in some cases require mixed domains that enable both aggregation and charge percolation to the electrodes.     

Simultaneous Enhancement of Three Parameters of P3HT‐Based Organic Solar Cells with One Oxygen Atom

Poly(3‐hexylthiophene) (P3HT)‐based organic solar cells (OSCs) have attracted much attention due to their advantages of low‐cost production and matured roll‐to‐roll manufacture. However, the efficiency of P3HT‐based OSCs lag much behind the non‐P3HT ones due to their negligible absorption of long wavelengths of light over 650 nm, high‐lying highest occupied molecular orbitals (HOMO), and difficulty of controlling morphology. In this study, the alkyl chains of the nonfullerene acceptors are replaced with alkoxy chains to achieve synergistic enhancement of all three parameters ( short circuit current density (J_SC), open circuit voltage (V_OC), and fill factor (FF)) and thus significant increase of power conversion efficiency for P3HT‐based OSCs. As a result, the OSCs exhibit a maxima efficiency of 6.6%. The P3HT‐based systems are systematically studied with optical spectroscopy, photoluminescence, cyclic voltametry, space charge limit current, grazing incident wide‐angle X‐ray scattering, transient absorption spectroscopy, transmission electron microscope, and atomic force microscopy to probe the mechanism, which reveal that introducing alkoxy chains simultaneously increases the energy levels of the HOMO and the lowest unoccupied molecular orbitals, enhances the light absorption, improves the rigidity of the backbone and charge transport mobility, and tunes the molecular orientation and film morphology, thus improving the photovoltaic performance. This contribution provides an important guidance in the design of novel nonfullerene acceptors for high‐performance P3HT‐based OSCs.     

Achieving Both Enhanced Voltage and Current through Fine‐Tuning Molecular Backbone and Morphology Control in Organic Solar Cells

It is a great challenge to simultaneously improve the two tangled parameters, open circuit voltage (V_oc) and short circuit current density (J_sc) for organic solar cells (OSCs). Herein, such a challenge is addressed by a synergistic approach using fine‐tuning molecular backbone and morphology control simultaneously by a simple yet effective side chain modulation on the backbone of an acceptor–donor–acceptor (A–D–A)‐type acceptor. With this, two terthieno[3,2‐b]thiophene (3TT) based A–D–A‐type acceptors, 3TT‐OCIC with backbone modulation and 3TT‐CIC without such modification, are designed and synthesized. Compared with the controlled molecule 3TT‐CIC, 3TT‐OCIC shows power conversion efficiency (PCE) of 13.13% with improved V_oc of 0.69 V and J_sc of 27.58 mA cm^?2, corresponding to PCE of 12.15% with V_oc of 0.65 V and J_sc of 27.04 mA cm^?2 for 3TT‐CIC–based device. Furthermore, with effective near infrared absorption, 3TT‐OCIC is used as the rear subcell acceptor in a tandem device and gave an excellent PCE of 15.72%.     

Improving Film Formation and Photovoltage of Highly Efficient Inverted‐Type Perovskite Solar Cells through the Incorporation of New Polymeric Hole Selective Layers

Two chemically tailored new conjugated copolymers, HSL1 and HSL2, were developed and applied as hole selective layers to improve the anode interface of fullerene/perovskite planar heterojunction solar cells. The introduction of polar functional groups on the polymer side chains increases the surface energy of the hole selective layers (HSLs), which promote better wetting with the perovskite films and lead to better films with full coverage and high crystallinity. The deep highest occupied molecular orbital levels of the HSLs align well with the valence band of the perovskite semiconductors, resulted in increase photovoltage. The high lying lowest unoccupied molecule orbital level provides sufficient electron blocking ability to prevent electrons from reaching the anode and reduces the interfacial trap‐assisted recombination at the poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/perovskite interface, resulting in a longer charge‐recombination lifetime and shorter charge‐extraction time. In the presence of the HSLs, high‐performance CH₃NH₃PbI _x Cl_{3? x} perovskite solar cells with a power conversion efficiency (PCE) of 16.6% (V _oc: 1.07 V) and CH₃NH₃Pb(I_0.3Br_0.7) _x Cl_{3? x} cells with a PCE of 10.3% (V _oc: 1.34 V) can be realized.     

Benzotriazole-Based Polymer Acceptor for High-Efficiency All-Polymer Solar Cells with High Photocurrent and Low Voltage Loss

The power conversion efficiencies (PCEs) of all-polymer solar cells (all-PSCs) have already exceeded 17%. However, the limited absorption range of an all-polymer system results in significantly reduced short-circuit current density (J_sc), which eventually influences the PCE improvement. To broaden the light absorption of polymer acceptors, herein, benzotriazole is introduced in the core unit of small molecule acceptors and thus two narrow-bandgap polymer acceptors named PTz-BO and PTz-C11 featuring the same molecular backbone and different side-chain length are synthesized. Compared with PTz-C11, the PTz-BO based-all PSCs deliver a slightly reduced J_sc, a large open-circuit voltage (V_oc) and a low voltage loss below 0.50 V. Moreover, ternary all-PSCs are constructed by introducing PTz-C11 as a guest component. Benefiting from the reduced recombination, improved exciton generation and dissociation, and balanced charge transport, a high efficiency of 16.58% is obtained for the ternary all-PSCs, with a high J_sc over 25 mA cm⁻² without sacrificing the V_oc. Such result represents the highest efficiency reported for benzotriazole-based all-PSCs in the literature thus far. This work demonstrates the great potential of benzotriazole for the synthesis of efficient narrow-bandgap polymer acceptors.     

Effects of Shortened Alkyl Chains on Solution‐Processable Small Molecules with Oxo‐Alkylated Nitrile End‐Capped Acceptors for High‐Performance Organic Solar Cells

Solution‐processable small molecules are significant for producing high‐performance bulk heterojunction organic solar cells (OSCs). Shortening alkyl chains, while ensuring proper miscibility with fullerene, enables modulation of molecular stacking, which is an effective method for improving device performance. Here, the design and synthesis of two solution‐processable small molecules based on a conjugated backbone with a novel end‐capped acceptor (oxo–alkylated nitrile) using octyl and hexyl chains attached to π–bridge, and octyl and pentyl chains attached to the acceptor is reported. Shortening the length of the widely used octyl chains improves self‐assembly and device performance. Differential scanning calorimetry and grazing incidence X‐ray diffraction results demonstrated that the molecule substituted by shorter chains shows tighter molecular stacking and higher crystallinity in the mixture with 6,6‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) and that the power conversion efficiency (PCE) of the OSC is as high as 5.6% with an open circuit voltage (V_oc) of 0.87 V, a current density (J_sc) of 9.94 mA cm^‐2, and an impressive filled factor (FF) of 65% in optimized devices. These findings provide valuable insights into the production of highly efficient solution‐processable small molecules for OSCs.     

Alkyl Chain Engineering of Solution‐Processable Star‐Shaped Molecules for High‐Performance Organic Solar Cells

The impact of alkyl side‐chain substituents on conjugated polymers on the photovoltaic properties of bulk heterojunction (BHJ) solar cells has been studied extensively, but their impact on small molecules has not received adequate attention. To reveal the effect of side chains, a series of star‐shaped molecules based on a triphenylamine (TPA) core, bithiophene, and dicyanovinyl units derivatized with various alkyl end‐capping groups of methyl, ethyl, hexyl and dodecyl is synthesiyed and studied to comprehensively investigate structure‐properties relationships. UV‐vis absorption and cyclic voltammetry data show that variations of alkyl chain length have little influence on the absorption and highest occupied molecular orbital (HOMO)‐lowest unoccupied molecular orbital (LUMO) levels. However, these seemingly negligible changes have a pronounced impact on the morphology of BHJ thin films as well as their charge carrier separation and transportation, which in turn influences the photovoltaic properties of these small‐molecule‐based BHJ devices. Solution‐processed organic solar cells (OSCs) based on the small molecule with the shortest methyl end groups exhibit high short circuit current (J_sc) and fill factor (FF), with an efficiency as high as 4.76% without any post‐treatments; these are among the highest reported for solution‐processed OSCs based on star‐shaped molecules.     

A Maverick Asymmetrical Backbone with Distinct Flanked Twist Angles Modulating the Molecular Aggregation and Crystallinity for High Performance Nonfullerene Solar Cells

In this work, a new asymmetrical backbone thienobenzodithiophene (TBD) containing four aromatic rings is designed, and then four polymers PTBD‐BZ, PTBD‐BDD, PTBD‐FBT, and PTBD‐Tz are synthesized. The planar and high degree of π‐conjugation configuration can guarantee effective charge carrier transport and the distinct flanked dihedral angles between the TBD core and conjugated side chain can subtly regulate the molecular aggregation and crystallinity. The four polymer/3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone)‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]‐dithiophene (ITIC) blending films exhibit predominantly face‐on orientation. The photovoltaic devices based on wide bandgap polymers PTBD‐BZ and PTBD‐BDD achieve power conversion efficiencies (PCEs) as high as 12.02% and 11.39% without any post‐treatment. For the medium bandgap polymers PTBD‐FBT and PTBD‐Tz, the devices also show good PCEs of 10.18% and 11.02% with high V_OC of 0.94 and 1.02 V, respectively, which indicates simultaneously achieving a V_OC > 1 V and a high J_SC is feasible to further improve the PSCs' performance by modifying this new backbone. This work reveals that the versatile asymmetric backbone is an excellent moiety to construct light‐harvesting copolymers and to modulate the microstructure for highly efficient PSCs.     

Bringing Conducting Polymers to High Order: Toward Conductivities beyond 105 S cm−1 and Thermoelectric Power Factors of 2 mW m−1 K−2

Here, an effective design strategy of polymer thermoelectric materials based on structural control in doped polymer semiconductors is presented. The strategy is illustrated for two archetypical polythiophenes, e.g., poly(2,5‐bis(3‐dodecyl‐2‐thienyl)thieno[3,2‐b]thiophene) (C₁₂‐PBTTT) and regioregular poly(3‐hexylthiophene) (P3HT). FeCl₃ doping of aligned films results in charge conductivities up to 2 × 10⁵ S cm^?1 and metallic‐like thermopowers similar to iodine‐doped polyacetylene. The films are almost optically transparent and show strongly polarized near‐infrared polaronic bands (dichroic ratio >10). The comparative study of structure–property correlations in P3HT and C₁₂‐PBTTT identifies three conditions to obtain conductivities beyond 10⁵ S cm^?1: i) achieve high in‐plane orientation of conjugated polymers with high persistence length; ii) ensure uniform chain oxidation of the polymer backbones by regular intercalation of dopant molecules in the polymer structure without disrupting alignment of π‐stacked layers; and iii) maintain a percolating nanomorphology along the chain direction. The highly anisotropic conducting polymer films are ideal model systems to investigate the correlations between thermopower S and charge conductivity σ. A scaling law S ∝ σ^?1/4 prevails along the chain direction, but a different S ∝ ?ln(σ) relation is observed perpendicular to the chains, suggesting different charge transport mechanisms. The simultaneous increase of charge conductivity and thermopower along the chain direction results in a substantial improvement of thermoelectric power factors up to 2 mW m^?1 K^?2 in C₁₂‐PBTTT.