The Effect of Hole Transport Material Pore Filling on Photovoltaic Performance in Solid‐State Dye‐Sensitized Solar Cells

A detailed investigation of the effect of hole transport material (HTM) pore filling on the photovoltaic performance of solid‐state dye‐sensitized solar cells (ss‐DSCs) and the specific mechanisms involved is reported. It is demonstrated that the efficiency and photovoltaic characteristics of ss‐DSCs improve with the pore filling fraction (PFF) of the HTM, 2,2’,7,7’‐tetrakis‐(N, N ‐di‐ p ‐methoxyphenylamine)9,9’‐spirobifluorene(spiro‐OMeTAD). The mechanisms through which the improvement of photovoltaic characteristics takes place were studied with transient absorption spectroscopy and transient photovoltage/photocurrent measurements. It is shown that as the spiro‐OMeTAD PFF is increased from 26% to 65%, there is a higher hole injection efficiency from dye cations to spiro‐OMeTAD because more dye molecules are covered with spiro‐OMeTAD, an order‐of‐magnitude slower recombination rate because holes can diffuse further away from the dye/HTM interface, and a 50% higher ambipolar diffusion coefficient due to an improved percolation network. Device simulations predict that if 100% PFF could be achieved for thicker devices, the efficiency of ss‐DSCs using a conventional ruthenium‐dye would increase by 25% beyond its current value.     

Hybrid Dye‐Titania Nanoparticles for Superior Low‐Temperature Dye‐Sensitized Solar Cells

In this work, a new strategy to design low‐temperature (≤200 °C) sintered dye‐sensitized solar cells (lt‐DSSC) is reported to enhance charge collection efficiencies (η_coll), photoconversion efficiencies (η), and stabilities under continuous operation conditions. Realization of lt‐DSSC is enabled by the integration of hybrid nanoparticles based on TiO₂‐Ru(II) complex (TiO₂_Ru_IS)—obtained by in situ bottom‐up construction of Ru(II) N3 dye‐sensitized titania—into the photoelectrode. Incentives for the use of TiO₂_Ru_IS are i) dye stability due to its integration into the TiO₂ anatase network and ii) enhanced charge collection yield due to its significant resistance toward electron recombination with electrolytes. It is demonstrated that devices with single‐layer photoelectrodes featuring blends of P25 and TiO₂_Ru_IS give rise to a 60% η_coll relative to a 46% η_coll for devices with P25‐based photoelectrodes. Responsible for this trend is a better charge transport and a reduced electron recombination. When using a multilayered photoelectrode architecture with a top layer based only on TiO₂_Ru_IS, devices with an even higher η_coll (74%) featuring a η of around 8.75% and stabilities of 600 h are achieved. This represents the highest values reported for lt‐DSSC to date.     

Stability and Dark Hysteresis Correlate in NiO‐Based Perovskite Solar Cells

In perovskite solar cells (PSCs), the interfaces are a weak link with respect to degradation. Electrochemical reactivity of the perovskite's halides has been reported for both molecular and polymeric hole selective layers (HSLs), and here it is shown that also NiO brings about this decomposition mechanism. Employing NiO as an HSL in p–i–n PSCs with power conversion efficiency (PCE) of 16.8%, noncapacitive hysteresis is found in the dark, which is attributable to the bias‐induced degradation of perovskite/NiO interface. The possibility of electrochemically decoupling NiO from the perovskite via the introduction of a buffer layer is explored. Employing a hybrid magnesium‐organic interlayer, the noncapacitive hysteresis is entirely suppressed and the device's electrical stability is improved. At the same time, the PCE is improved up to 18% thanks to reduced interfacial charge recombination, which enables more efficient hole collection resulting in higher V_oc and FF.     

High‐Surface‐Area Porous Platinum Electrodes for Enhanced Charge Transfer

Cobalt‐based electrolytes are highly tunable and have pushed the limits of dye‐sensitized solar cells, enabling higher open‐circuit voltages and new record efficiencies. However, the performance of these electrolytes and a range of other electrolytes suffer from slow electron transfer at platinum counter electrodes. High surface area platinum would enhance catalysis, but pure platinum structures are too expensive in practice. Here, a material‐efficient host‐guest architecture is developed that uses an ultrathin layer of platinum deposited upon an electrically conductive scaffold, niobium‐doped tin oxide (NTO). This nanostructured composite enhances the counter electrode performance of dye‐sensitized solar cells (DSCs) using a Co^(II/III)BPY₃ electrolyte with an increased fill factor and power conversion efficiency (11.26%), compared to analogous flat films. The modular strategy is elaborated by integrating a light scattering layer onto the counter electrode to reflect unabsorbed light back to the photoanode to improve the short‐circuit current density and power conversion efficiency.     

Porphyrin Sensitizers with Donor Structural Engineering for Superior Performance Dye‐Sensitized Solar Cells and Tandem Solar Cells for Water Splitting Applications

Zn(II)–porphyrin sensitizers, coded as SGT‐020 and SGT‐021 , are designed and synthesized through donor structural engineering. The photovoltaic (PV) performances of SGT sensitizer‐based dye‐sensitized solar cells (DSSCs) are systematically evaluated in a thorough SM315 as a reference sensitizer. The effect of the donor ability and the donor bulkiness on photovoltaic performances is investigated for establishing the structure–performance relationship in the platform of porphyrin‐triple bond‐benzothiadiazole‐acceptor sensitizers. By introducing a more bulky fluorene unit to the amine group in the SM315 , the power conversion efficiency (PCE) is enhanced with the increased short‐circuit current (J_sc) and open‐circuit voltage (V_oc), due to the improved light‐harvesting ability and the efficient prevention of charge recombination, respectively. As a consequence, a maximum PCE of 12.11% is obtained for SGT‐021 , whose PCE is much higher than the 11.70% PCE for SM315 . To further improve their maximum efficiency, the first parallel tandem DSSCs employing cobalt electrolyte in the top and bottom cells are demonstrated and an extremely high efficiency of 14% is achieved, which is currently the highest reported value for tandem DSSCs. The series tandem DSSCs give a remarkably high V_oc value of >1.83 V. From this DSSC tandem configuration, 7.4% applied bias photon‐to‐current efficiency is achieved for solar water splitting.     

Solid‐State Dye‐Sensitized Solar Cells Using a Novel Class of Ullazine Dyes as Sensitizers

Here we present the photovoltaic performance of solid‐state dye‐sensitized solar cells (DSCs) using a series of ullazine‐based metal‐free organic sensitizers and spiro‐MeOTAD as a hole‐transport material. A maximum of 4.95% power conversion efficiency measured under standard AM 1.5G illumination (100 mW cm^?2) was achieved with the best performing ullazine dye, and was further improved to 5.40% through co‐sensitization with the triphenylamine‐based organic sensitizer, D35. This study investigates the effect of the molecular structure of the ullazine sensitizer on the performance in solid‐state DSCs.     

Hexylthiophene‐Featured D–A–π–A Structural Indoline Chromophores for Coadsorbent‐Free and Panchromatic Dye‐Sensitized Solar Cells

For a sensitizer with a strong π‐conjugation system, a coadsorbent is needed to hinder dye aggregation. However, coadsorption always brings a decrease in dye coverage on the TiO₂ surface. Organic ‘‘D–A–π–A’’ dyes, WS‐6 and WS‐11, are designed and synthesized based on the known WS‐2 material for coadsorbent‐free, dye‐sensitized solar cells (DSSCs). Compared with the traditional D–π–A structure, these D–A–π–A indoline dyes, with the additional incorporated acceptor unit of benzothiadiazole in the π‐conjugation, exhibit a broad photoresponse, high redox stability, and convenient energy‐level tuning. The attached n‐hexyl chains in both dyes are effective to suppress charge recombination, resulting in a decreased dark current and enhanced open‐circuit voltage. Electrochemical impedance spectroscopy studies indicate that both the resistance for charge recombination and the electron lifetime are increased after the introduction of alkyl chains to the dye molecules. Without deoxycholic acid coadsorption, the power‐conversion efficiency of WS‐6 (7.76%) on a 16 μm‐thick TiO₂ film device is 45% higher than that of WS‐2 (5.31%) under the same conditions. The additional n‐hexylthiophene in WS‐11 extends the photoresponse to a panchromatic spectrum but causes a low incident photon‐to‐current conversion efficiency.     

Physically Stable Polymer‐Membrane Electrolytes for Highly Efficient Solid‐State Dye‐Sensitized Solar Cells with Long‐Term Stability

A 3D polymer‐network‐membrane (3D‐PNM) electrolyte is described for highly stable, solid‐state dye‐sensitized solar cells (DSCs) with excellent power‐conversion efficiency (PCE). The 3D‐PNM electrolyte is prepared by using one‐pot in situ cross‐linking polymerization on the surface of dye‐sensitized TiO₂ particles in the presence of redox species. This method allows the direct connection of the 3D‐PNM to the surface of the TiO₂ particles as well as the in situ preparation of the electrolyte gel during device assembly. There are two junction areas (liquid and solid‐state junctions) in the DSCs that employ conventional polymer electrolytes, and the major interface is at the liquid‐state junction. The solid‐state junction is dominant in the DSCs that employ the 3D‐PNM electrolyte, which exhibit almost constant performance during aging at 65 °C for over 700 h (17.0 to 17.2 mA cm^–2). The best cell performance gives a PCE of 9.1%; this is slightly better than the performance of a DSC that employs a liquid electrolyte.     

Room‐Temperature Vapor Deposition of Cobalt Nitride Nanofilms for Mesoscopic and Perovskite Solar Cells

Organic/inorganic hybrid solar cells, typically mesoscopic and perovskite solar cells, are regarded as promising candidates to replace conventional silicon or thin film photovoltaics. There have been intensive investigations on the development of advanced materials for improved power conversion efficiencies, however, economical feasibilities and reliabilities of the organic/inorganic photovoltaics are yet to reach at a sufficient level for practical utilizations. In this study, cobalt nitride (CoN) nanofilms prepared by room‐temperature vapor deposition in an inert N₂ atmosphere, which is a facile and highly reproducible procedure, are proposed as a low‐cost counter electrode in mesoscopic dye‐sensitized solar cells (DSCs) and a hole transport material in inverted planar perovskite solar cells (PSCs) for the first time. The CoN film successfully replaces conventional Pt in DSCs, resulting in a power conversion efficiency comparable to the ones based on Pt. In addition, PSCs employing the CoN manifest high efficiency even up to 15.0%, which is comparable to state‐of‐the‐art performance in the cases of PSCs employing inorganic hole transporters. Furthermore, flexible solar cell applications of the CoN are performed in both mesoscopic and perovskite solar cells, verifying the advantages of the room‐temperature deposition process and feasibilities of the CoN nanofilms in various fields.     

Engineering Processes at the Interface of p‐Semiconductor for Enhancing the Open Circuit Voltage in p‐Type Dye‐Sensitized Solar Cells

To prevent the interfacial charge recombination between injected holes in the valence band and the redox mediator in the electrolyte in p‐type dye sensitized solar cells (p‐DSSC) the passivation of the recombination sites by organic insulator chenodeoxycholic acid (CDCA) layer is critically investigated in this study. Rather than classical coating of the semiconductor's surface by simultaneous co‐adsorption of CDCA during the dyeing step, two other methods are investigated. The first consists in dissolving CDCA in the electrolyte, while the second consists in spin coating an ethanol solution of CDCA onto the already dyed photocathode. In this study, different sensitizers, electrolytes, and p‐SCs, (NiO, CuGaO₂) are explored. Analysis of the current/voltage curves and electrochemical impedance spectroscopy provides evidence that the role of the CDCA layer is to create a physical barrier to prevent the approach of the redox mediator from the NiO surface and consequently raise the open circuit voltage (V_oc). The important finding of this study is the demonstration that the V_oc in p‐DSSC is heavily limited by interfacial charge recombination and that higher V_oc values much above 100 mV and as high as 500 mV can be attained with conventional materials (NiO) if this deleterious side reaction can be suppressed or diminished.     

Dual Functional Electron‐Selective Contacts Based on Silicon Oxide/Magnesium: Tailoring Heterointerface Band Structures while Maintaining Surface Passivation

Silicon (Si)‐based dopant‐free heterojunction solar cells (SCs) featuring carrier‐selective contacts (CSCs) have attracted considerable interest due to the extreme simplifications in their device structure and manufacturing procedure. However, these SCs are limited by the unsatisfactory contact properties on both sides of the junction, and their efficiencies are not comparable with those of commercially available Si SCs. In this report, a high‐performance silicon‐oxide/magnesium (SiO_x/Mg) electron‐selective contact (ESC) design is described. Combining an ultrathin SiO_x and a low work function Mg layer, the novel ESC simultaneously yields low recombinative and resistive losses. In addition, deposition of Mg on SiO_x relaxes the restriction on the threshold thickness of the SiO_x for electron tunneling and therefore broadens the optimization space for rear‐sided passivation. Meanwhile, hole‐selective contact with boosted light harvesting and suppressed interfacial recombination is achieved by forming a fully conformal contact between the conducting poly(3,4‐ethylene dioxythiophene): poly(styrenesulfonate) (PEDOT: PSS) and periodic Si pyramid arrays. With the double‐sided carrier‐selective contact designs, PEDOT: PSS/Si/SiO_x/Mg SCs with efficiency of 15% are finally obtained via a totally dopant‐free processing. Subsequent calculations further indicate a pathway for the improvement of these contacts toward an efficiency that is competitive with conventionally diffused pn junction SCs.     

Achieving 17.4% Efficiency of Ternary Organic Photovoltaics with Two Well‐Compatible Nonfullerene Acceptors for Minimizing Energy Loss

A power conversion efficiency (PCE) of 16.2% is achieved in PM6:BTP‐4F‐12 based organic photovoltaics (OPVs). On the basis of efficient binary OPVs, a series of ternary OPVs are constructed by incorporating MeIC as the third component. The open circuit voltages (V_OCs) of ternary OPVs can be gradually increased along with the incorporation of MeIC, suggesting the formation of an alloy state between BTP‐4F‐12 and MeIC with good compatibility. The energy loss (E_loss) of ternary OPVs can be decreased compared with that of two binary OPVs, contributing to the V_OC improvement of ternary OPVs. The short circuit current density (J_SC) and fill factor (FF) of ternary OPVs can also be simultaneously enhanced with MeIC content up to 10 wt% in acceptors, leading to 17.4% PCE of the optimized ternary OPVs. The J_SC and FF improvement of ternary OPVs is thought to result from the optimized ternary active layers with more efficient photon harvesting, exciton dissociation and charge transport. The 17.4% PCE and 79.2% FF is among the top values of ternary OPVs. This work indicates that a ternary strategy is an emerging method to simultaneously minimize E_loss and optimize photon harvesting as well as improve the morphology of active layers for realizing performance improvement for OPVs.     

Titanium Dioxide Mesoporous Electrodes for Solid‐State Dye‐Sensitized Solar Cells: Cross‐Analysis of the Critical Parameters

We report a comparative study on the use of four different mesoporous titanium dioxide (TiO₂) photo‐electrodes for the fabrication of solid‐state dye‐sensitized solar cells (sDSSCs). The photovoltaic parameters of the device correlate with several intrinsic properties of the film, based not only on its morphological features, as commonly considered in standard characterizations, but also on the transport and the electronic properties of the photo‐electrode. These properties differ significantly for TiO₂ electrodes processed using different colloidal pastes, and are decisive for the photovoltaic efficiency, ranging from 3.7% up to 5.1%. In particular, the dielectric permittivity of each mesoporous layer (ε_eff) and the number of traps (N_t) determined by the space‐charge‐limited current (SCLC) theory are found to be a bottle‐neck for the charge transport, greatly influencing the fill factor (FF) and open circuit voltage (V_oc) of the cells. In addition, a direct correlation between TiO₂ surface potential with the V_oc was established. Cross‐analysis of key macroscopic parameters of the films prior to integration in the devices, in particular focusing on the determination of the capacitance and surface potential shift of the TiO₂ mesoporous anode, represents a straightforward yet powerful method to screen and select the most suitable TiO₂ for applications in sDSSCs.     

Aerosol OT/Water System Coupled with Triiodide/Iodide (I3−/I−) Redox Electrolytes for Highly Efficient Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSCs) are considered to be a promising alternative to Si‐based photovoltaic cells. The electrolyte of the DSC primarily uses triiodide/iodide (I₃^?/I^?) as a redox couple. Therefore, it is essential to understand the regeneration and recombination kinetics of the I₃^?/I^? redox couples in the device. In this context, controlling the total and local concentrations of the I₃^?/I^? redox couples is an important parameter that can influence the DSC performance. Here, we propose that the introduction of a sodium bis (2‐ethylhexyl) sulfosuccinate (AOT)/water system to the I₃^?/I^? electrolyte enables the control of the concentration of the redox couples, which consequently achieves a high power conversion efficiency of ～11% for ～1000 h (under 1 sun illumination) owing to the enhanced dye‐regeneration efficiency and the reduced recombination rate. This novel concept assists in the comprehension of the regeneration and recombination kinetics and develops highly efficient DSCs.     

Overcoming Interfacial Losses in Solution‐Processed Organic Multi‐Junction Solar Cells

Organic solar cells are promising in terms of full‐solution‐processing which enables low‐cost and large‐scale fabrication. While single‐junction solar cells have seen a boost in power conversion efficiency (PCE), multi‐junction solar cells are promising to further enhance the PCE. In all‐solution‐processed multi‐junction solar cells, interfacial losses are often encountered between hole‐transporting layer (HTL) and the active layers and therefore greatly limit the application of newly developed high‐performance donor and acceptor materials in multi‐junction solar cells. Here, the authors report on a systematic study of interface losses in both single‐junction and multi‐junction solar cells based on representative polymer donors and HTLs using electron spectroscopy and time‐of‐flight secondary ion mass spectrometry. It is found that a facile mixed HTL containing poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and MoO _x nanoparticles successfully overcomes the interfacial losses in both single‐ and multi‐junction solar cells based on various active layers by reducing interface protonation, promoting better energy‐level alignment, and forming a dense and smooth layer. Solution‐processed single‐junction solar cells are demonstrated to reach the same performance as with evaporated MoO _x (over 7%). Multi‐junction solar cells with polymers containing nitrogen atoms as the first layer and the mixed PEDOT:PSS and MoO _x nanoparticles as hole extraction layer reach fill factor (FF) of over 60%, and PCE of over 8%, while the identical stack with pristine PEDOT:PSS or MoO _x nanoparticles show FF smaller than 50% and PCE less than 5%.     

High Electron Affinity Enables Fast Hole Extraction for Efficient Flexible Inverted Perovskite Solar Cells

Inverted perovskite solar cells (PSCs) with low‐temperature processed hole transporting materials (HTMs) suffer from poor performance due to the inferior hole‐extraction capability at the HTM/perovskite interfaces. Here, molecules with controlled electron affinity enable a HTM with conductivity improved by more than ten times and a decreased energy gap between the Fermi level and the valence band from 0.60 to 0.24 eV, leading to the enhancement of hole‐extraction capacity by five times. As a result, the 3,6‐difluoro‐2,5,7,7,8,8‐hexacyanoquinodimethane molecules are used for the first time enhancing open‐circuit voltage (V_oc) and fill factor (FF) of the PSCs, which enable rigid‐and flexible‐based inverted perovskite devices achieving highest power conversion efficiencies of 22.13% and 20.01%, respectively. This new method significantly enhances the V_oc and FF of the PSCs, which can be widely combined with HTMs based on not only NiO_x but also PTAA, PEDOTT:PSS, and CuSCN, providing a new way of realizing efficient inverted PSCs.     

Highly stable and Efficient Perovskite Solar Cells Based on FAMA‐Perovskite‐Cu:NiO Composites with 20.7% Efficiency and 80.5% Fill Factor

To solve critical issues related to device stability and performance of perovskite solar cells (PSCs), FA_0.026MA_0.974PbI_3?yCl_y‐Cu:NiO (formamidinium methylammonium (FAMA)‐perovskite‐Cu:NiO) and Al₂O₃/Cu:NiO composites are developed and utilized for fabrication of highly stable and efficient PSCs through fully‐ambient‐air processes. The FAMA‐perovskite‐Cu:NiO composite crystals prepared without using any antisolvents not only improve the perovskite film quality with large‐size crystals and less grain boundaries but also tailor optical and electronic properties and suppress charge recombination with reduction of trap density. A champion device based on the composites as light absorber and Al₂O₃/Cu:NiO interfacial layer between electron transport layer and active layer yields power conversion efficiency (PCE) of 20.67% with V_OC of 1.047 V, J_SC of 24.51 mA cm^?2, and fill factor of 80.54%. More importantly, such composite‐based PSCs without encapsulation show significant enhancement in long‐term air‐stability, thermal‐ and photostability with retaining 97% of PCE over 240 d under ambient conditions (25–30 °C, 45–55% humidity).     

TiO2 Nanocrystals Synthesized by Laser Pyrolysis for the Up‐Scaling of Efficient Solid‐State Dye‐Sensitized Solar Cells

A crucial issue regarding emerging nanotechnologies remains the up‐scaling of new functional nanostructured materials towards their implementation in high performance applications on a large scale. In this context, we demonstrate high efficiency solid‐state dye‐sensitized solar cells prepared from new porous TiO₂ photoanodes based on laser pyrolysis nanocrystals. This strategy exploits a reduced number of processing steps as well as non‐toxic chemical compounds to demonstrate highly porous TiO₂ films. The possibility to easily tune the TiO₂ nanocrystal physical properties allows us to demonstrate all solid‐state dye‐sensitized devices based on a commercial benchmark materials (organic indoline dye and molecular hole transporter) presenting state‐of‐the‐art performance comparable with reference devices based on a commercial TiO₂ paste. In particular, a drastic improvement in pore infiltration, which is found to balance a relatively lower surface area compared to the reference electrode, is evidenced using laser‐synthesized nanocrystals resulting in an improved short‐circuit current density under full sunlight. Transient photovoltage decay measurements suggest that charge recombination kinetics still limit device performance. However, the proposed strategy emphasizes the potentialities of the laser pyrolysis technique for up‐scaling nanoporous TiO₂ electrodes for various applications, especially for solar energy conversion.     

The Introduction of Fluorine and Sulfur Atoms into Benzotriazole‐Based p‐Type Polymers to Match with a Benzotriazole‐Containing n‐Type Small Molecule: “The Same‐Acceptor‐Strategy” to Realize High Open‐Circuit Voltage

“The Same‐Acceptor‐Strategy” (SAS) adopts benzotriazole (BTA)‐based p‐type polymers paired with a new BTA based non‐fullerene acceptor BTA13 to minimize the trade‐off between the open‐circuit voltage (V_OC) and short circuit current (J_SC). The fluorination and sulfuration are introduced to lower the highest occupied molecular orbitals (HOMO) of the polymers. The fluorinated polymer of J52‐F shows the higher power conversion efficiency (PCE) of 8.36% than the analog polymer of J52, benefited from a good balance between an improved V_OC of 1.18 V and a J_SC of 11.55 mA cm^?2. Further adding alkylthio groups on J52‐F, the resulted polymer, J52‐FS, exhibits the highest V_OC of 1.24 V with a decreased energy loss of 0.48 eV, compared with 0.67 eV for J52 and 0.54 eV for J52‐F. However, J52‐FS shows an inferior PCE (3.84%) with a lower J_SC of 6.74 mA cm^?2, because the small ΔE_HOMO between J52‐FS and BTA13 (0.02 eV) gives rise to the inefficient hole transfer and high charge recombination, as well as low carrier mobilities. The results of this study clearly demonstrate that the introduction of different atoms in p‐type polymers is effective to improve the SAS and realize the high (V_OC) and PCE.     

Thieno[3,2‐b][1]benzothiophene Derivative as a New π‐Bridge Unit in D–π–A Structural Organic Sensitizers with Over 10.47% Efficiency for Dye‐Sensitized Solar Cells

Three new thieno[3,2‐b][1]benzothiophene ( TBT )‐based donor–π–acceptor (D–π–A) sensitizers, coded as SGT ‐ 121 , SGT ‐ 129 , and SGT ‐ 130 , have been designed and synthesized for dye‐sensitized solar cells (DSSCs), for the first time. The TBT , prepared by fusing thiophene unit with the phenyl unit of triphenylamine donor, is utilized as the π‐bridge for all sensitizers with good planarity. They have been molecularly engineered to regulate the highest occupied molecular orbital (HOMO)‐lowest unoccupied molecular orbital (LUMO) energy levels and extend absorption range as well as to control the electron‐transfer process that can ensure efficient dye regeneration and prevent undesired electron recombination. The photovoltaic performance of SGT‐sensitizer‐based DSSCs employing Co(bpy)₃^2+/3+ (bpy = 2,2′‐bipyridine) redox couple is systematically evaluated in a thorough comparison with Y123 as a reference sensitizer. Among them, SGT ‐ 130 with benzothiadiazole‐phenyl ( BTD ‐ P ) unit as an auxiliary acceptor exhibits the highest power‐conversion efficiency (PCE) of 10.47% with J_sc = 16.77 mA cm^?2, V_oc = 851 mV, and FF = 73.34%, whose PCE is much higher than that of Y123 (9.5%). It is demonstrated that the molecular combination of each fragment in D–π–A organic sensitizers can be a pivotal factor for achieving the higher PCEs and an innovative strategy for strengthening the drawbacks of the π‐bridge.