Active Edge Sites Engineering in Nickel Cobalt Selenide Solid Solutions for Highly Efficient Hydrogen Evolution

An effective multifaceted strategy is demonstrated to increase active edge site concentration in Ni_0.33Co_0.67Se₂ solid solutions prepared by in situ selenization process of nickel cobalt precursor. The simultaneous control of surface, phase, and morphology result in as‐prepared ternary solid solution with extremely high electrochemically active surface area (C _dl = 197 mF cm^?2), suggesting significant exposure of active sites in this ternary compound. Coupled with metallic‐like electrical conductivity and lower free energy for atomic hydrogen adsorption in Ni_0.33Co_0.67Se₂, identified by temperature‐dependent conductivities and density functional theory calculations, the authors have achieved unprecedented fast hydrogen evolution kinetics, approaching that of Pt. Specifically, the Ni_0.33Co_0.67Se₂ solid solutions show a low overpotential of 65 mV at ?10 mV cm^?2, with onset potential of mere 18 mV, an impressive small Tafel slope of 35 mV dec^?1, and a large exchange current density of 184 µA cm^?2 in acidic electrolyte. Further, it is shown that the as‐prepared Ni_0.33Co_0.67Se₂ solid solution not only works very well in acidic electrolyte but also delivers exceptional hydrogen evolution reaction (HER) performance in alkaline media. The outstanding HER performance makes this solid solution a promising candidate for mass hydrogen production.     

Reduced Mesoporous Co3O4 Nanowires as Efficient Water Oxidation Electrocatalysts and Supercapacitor Electrodes

While electrochemical water splitting is one of the most promising methods to store light/electrical energy in chemical bonds, a key challenge remains in the realization of an efficient oxygen evolution reaction catalyst with large surface area, good electrical conductivity, high catalytic properties, and low fabrication cost. Here, a facile solution reduction method is demonstrated for mesoporous Co₃O₄ nanowires treated with NaBH₄. The high‐surface‐area mesopore feature leads to efficient surface reduction in solution at room temperature, which allows for retention of the nanowire morphology and 1D charge transport behavior, while at the same time substantially increasing the oxygen vacancies on the nanowire surface. Compared to pristine Co₃O₄ nanowires, the reduced Co₃O₄ nanowires exhibit a much larger current of 13.1 mA cm^‐2 at 1.65 V vs reversible hydrogen electrode (RHE) and a much lower onset potential of 1.52 V vs RHE. Electrochemical supercapacitors based on the reduced Co₃O₄ nanowires also show a much improved capacitance of 978 F g^‐1 and reduced charge transfer resistance. Density‐functional theory calculations reveal that the existence of oxygen vacancies leads to the formation of new gap states in which the electrons previously associated with the Co‐O bonds tend to be delocalized, resulting in the much higher electrical conductivity and electrocatalytic activity.     

Interface Engineering of Hierarchical Branched Mo‐Doped Ni3S2/NixPy Hollow Heterostructure Nanorods for Efficient Overall Water Splitting

Rational design and construction of bifunctional electrocatalysts with excellent activity and durability is imperative for water splitting. Herein, a novel top‐down strategy to realize a hierarchical branched Mo‐doped sulfide/phosphide heterostructure (Mo‐Ni₃S₂/Ni_xP_y hollow nanorods), by partially phosphating Mo‐Ni₃S₂/NF flower clusters, is proposed. Benefitting from the optimized electronic structure configuration, hierarchical branched hollow nanorod structure, and abundant heterogeneous interfaces, the as‐obtained multisite Mo‐Ni₃S₂/Ni_xP_y/NF electrode has remarkable stability and bifunctional electrocatalytic activity in the hydrogen evolution reaction (HER)/oxygen evolution reaction (OER) in 1 m KOH solutions. It possesses an extremely low overpotential of 238 mV at the current density of 50 mA cm^?2 for OER. Importantly, when assembled as anode and cathode simultaneously, it merely requires an ultralow cell voltage of 1.46 V to achieve the current density of 10 mA cm^?2, with excellent durability for over 72 h, outperforming most of the reported Ni‐based bifunctional materials. Density functional theory results further confirm that the doped heterostructure can synergistically optimize Gibbs free energies of H and O‐containing intermediates (OH*, O*, and OOH*) during HER and OER processes, thus accelerating the catalytic kinetics of electrochemical water splitting. This work demonstrates the importance of the rational combination of metal doping and interface engineering for advanced catalytic materials.     

A Pair of NiCo2O4 and V2O5 Nanowires Directly Grown on Carbon Fabric for Highly Bendable Lithium‐Ion Batteries

Mechanically bendable and flexible functionalities are urgently required for next‐generation battery systems that will be included in soft and wearable electronics, active sportswear, and origami‐based deployable space structures. However, it is very difficult to synthesize anode and cathode electrodes that have high energy density and structural reliability under large bending deformation. Here, vanadium oxide (V₂O₅) and nickel cobalt oxide (NiCo₂O₄) nanowire‐carbon fabric electrodes for highly flexible and bendable lithium ion batteries are reported. The vanadium oxide and nickel cobalt oxide nanowires were directly grown on plasma‐treated carbon fabric and were used as cathode and anode electrodes in a full cell lithium ion battery. Most importantly, a pre‐lithiation process was added to the nickel cobalt oxide nanowire anode to facilitate the construction of a full cell using symmetrically‐architectured nanowire‐carbon fabric electrodes. The highly bendable full cell based on poly(ethylene oxide) polymer electrolyte and room temperature ionic liquid shows high energy density of 364.2 Wh kg^?1 at power density of 240 W kg^?1, without significant performance degradation even under large bending deformations. These results show that vanadium oxide and lithiated nickel cobalt oxide nanowire‐carbon fabrics are a good combination for binder‐free electrodes in highly flexible lithium‐ion batteries.     

A Perovskite Nanorod as Bifunctional Electrocatalyst for Overall Water Splitting

The development of highly efficient and low‐cost electrocatalysts for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is paramount for water splitting associated with the storage of clean and renewable energy. Here, this study reports its findings in the development of a nanostructured perovskite oxide as OER/HER bifunctional electrocatalyst for overall water splitting. Prepared by a facile electrospinning method, SrNb_0.1Co_0.7Fe_0.2O_3–δ perovskite nanorods (SNCF‐NRs) display excellent OER and HER activity and stability in an alkaline solution, benefiting from the catalytic nature of perovskites and unique structural features. More importantly, the SNCF‐NR delivers a current density of 10 mA cm^?2 at a cell voltage of merely ≈1.68 V while maintaining remarkable durability when used as both anodic and cathodic catalysts in an alkaline water electrolyzer. The performance of this bifunctional perovskite material is among the best ever reported for overall water splitting, offering a cost‐effective alternative to noble metal based electrocatalysts.     

Theoretical and Experimental Insight into the Effect of Nitrogen Doping on Hydrogen Evolution Activity of Ni3S2 in Alkaline Medium

Nickel sulfide (Ni₃S₂) is a promising hydrogen evolution reaction (HER) catalyst by virtue of its metallic electrical conductivity and excellent stability in alkaline medium. However, the reported catalytic activities for Ni₃S₂ are still relatively low. Herein, an effective strategy to boost the H adsorption capability and HER performance of Ni₃S₂ through nitrogen (N) doping is demonstrated. N‐doped Ni₃S₂ nanosheets achieve a fairly low overpotential of 155 mV at 10 mA cm^?2 and an excellent exchange current density of 0.42 mA cm^?2 in 1.0 m KOH electrolyte. The mass activity of 16.9 mA mg^?1 and turnover frequency of 2.4 s^?1 obtained at 155 mV are significantly higher than the values reported for other Ni₃S₂‐based HER catalysts, and comparable to the performance of best HER catalysts in alkaline medium. These experimental data together with theoretical analysis suggest that the outstanding catalytic activity of N‐doped Ni₃S₂ is due to the enriched active sites with favorable H adsorption free energy. The activity in the Ni₃S₂ is highly correlated with the coordination number of the surface S atoms and the charge depletion of neighbor Ni atoms. These new findings provide important guidance for future experimental design and synthesis of optimal HER catalysts.     

Atomically Dispersed Mo Supported on Metallic Co9S8 Nanoflakes as an Advanced Noble‐Metal‐Free Bifunctional Water Splitting Catalyst Working in Universal pH Conditions

Water splitting requires development of cost‐effective multifunctional materials that can catalyze both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) efficiently. Currently, the OER relies on the noble‐metal catalysts; since with other catalysts, its operation environment is greatly limited in alkaline conditions. Herein, an advanced water oxidation catalyst based on metallic Co₉S₈ decorated with single‐atomic Mo (0.99 wt%) is synthesized (Mo‐Co₉S₈@C). It exhibits pronounced water oxidization activity in acid, alkali, and neutral media by showing positive onset potentials of 200, 90, and 290 mV, respectively, which manifests the best Co₉S₈‐based single‐atom Mo catalyst till now. Moreover, it also demonstrates excellent HER performance over a wide pH range. Consequently, the catalyst even outperforms noble metal Pt/IrO₂‐based catalysts for overall water splitting (only requiring 1.68 V in acid, and 1.56 V in alkaline). Impressively, it works under a current density of 10 mA cm^?2 with no obvious decay during a 24 h (0.5 m H₂SO₄) and 72 h (1.0 m KOH) durability experiment. Density functional theory (DFT) simulations reveal that the synergistic effects of atomically dispersed Mo with Co‐containing substrates can efficiently alter the binding energies of adsorbed intermediate species and decrease the overpotentials of the water splitting.     

MOF Template‐Directed Fabrication of Hierarchically Structured Electrocatalysts for Efficient Oxygen Evolution Reaction

The ever‐increasing demand for clean and renewable power sources has sparked intensive research on water splitting to produce hydrogen, in which the exploration of electrocatalysts is the central issue. Herein, a new strategy, metal–organic framework template‐directed fabrication of hierarchically structured Co₃O₄@X (X = Co₃O₄, CoS, C, and CoP) electrocatalysts for efficient oxygen evolution reaction (OER) is developed, where Co₃O₄@X are derived from cobalt carbonatehydroxide@zeolitic‐imidazolate‐framework‐67 (CCH@ZIF‐67). Unique hierarchical structure and synergistic effect of resulting catalysts endow abundant exposed active sites, facile ion diffusion path, and improved conductivity, being favorable for improving catalytic activity of them. Consequently, these derivatives Co₃O₄@X reveal highly efficient electrocatalytic performance with long‐term durability for the OER, much superior to previously reported cobalt‐based catalysts as well as the Ir/C catalyst. Particularly, Co₃O₄@CoP exhibits the highest electrocatalytic capability with the lower overpotential of 238 mV at the current density of 10 mA cm^?2. Furthermore, Co₃O₄@X can also efficiently catalyze other small molecules through electro‐oxidation reaction (e.g., glycerol, methanol, or ethanol). It is expected that the strategy presented here can be extended to the fabrication of other composite electrode materials with hierarchical structures for more efficient water splitting.     

Benchmarking the Activity,Stability, and Inherent Electrochemistry of Amorphous Molybdenum Sulfide for Hydrogen Production

Anodically electrodeposited amorphous molybdenum sulfide (AE‐MoS_x) has attracted significant attention as a non‐noble metal electrocatalyst for its high activity toward the hydrogen evolution reaction (HER). The [Mo₃S₁₃]^2? polymer‐based structure confers a high density of exposed sulfur moieties, widely regarded as the HER active sites. However, their intrinsic complexity conceals full understanding of their exact role in HER catalysis, hampering their full potential for water splitting applications. In this report, a unifying approach is adopted accounting for modifications in the inherent electrochemistry (EC), HER mechanism, and surface species to maximize the AE‐MoS_x electroactivity over a broad pH region (0–10). Dramatic enhancements in HER performance by selective electrochemical cycling within reductive (overpotential shift, η_HER ≈ ?350 mV) and electro‐oxidative windows (η_HER ≈ ?290 mV) are accompanied by highly stable performance in mildly acidic electrolytes. Joint analysis of X‐ray photoelectron spectroscopy, Raman, and EC experiments corroborate the key role of bridging and terminal S ligands as active site generators at low pH, and reveal molybdenum oxysulfides (Mo⁵⁺O_xS_y) to be the most active HER moiety in AE‐MoS_x in mildly acidic‐to‐neutral environments. These findings will be extremely beneficial for future tailoring of MoS_x materials and their implementation in commercial electrolyzer technologies.     

Hydrothermal Synthesis of Monolithic Co3Se4 Nanowire Electrodes for Oxygen Evolution and Overall Water Splitting with High Efficiency and Extraordinary Catalytic Stability

Cobalt selenide has been proposed to be an effective low‐cost electrocatalyst toward the oxygen evolution reaction (OER) due to its well‐suited electronic configuration. However, pure cobalt selenide has by far still exhibited catalytic activity far below what is expected. Herein, this paper for the first time reports the synthesis of new monoclinic Co₃Se₄ thin nanowires on cobalt foam (CF) via a facile one‐pot hydrothermal process using selenourea. When used to catalyze the OER in basic solution, the conditioned monolithic self‐supported Co₃Se₄/CF electrode shows an exceptionally high catalytic current of 397 mA cm^?2 at a low overpotential (η) of 320 mV, a small Tafel slope of 44 mV dec^?1, a turnover frequency of 6.44 × 10^?2 s^?1 at η = 320 mV, and excellent electrocatalytic stability at various current densities. Furthermore, an electrolyzer is assembled using two symmetrical Co₃Se₄/CF electrodes as anode and cathode, which can deliver 10 and 20 mA cm^?2 at low cell voltages of 1.59 and 1.63 V, respectively. More significantly, the electrolyzer can operate at 10 mA cm^?2 over 3500 h and at 100 mA cm^?2 for at least 2000 h without noticeable degradation, showing extraordinary operational stability.     

Robust Sub‐Monolayers of Co3O4 Nano‐Islands: A Highly Transparent Morphology for Efficient Water Oxidation Catalysis

The scalable synthesis of highly transparent and robust sub‐monolayers of Co₃O₄ nano‐islands, which efficiently catalyze water oxidation, is reported. Rapid aerosol deposition of Co₃O₄ nanoparticles and thermally induced self‐organization lead to an ultra‐fine nano‐island morphology with more than 94% light transmission at a wavelength of 500 nm. These transparent sub‐monolayers demonstrate a remarkable mass‐weighted water oxidation activity of 2070–2350 A g_Co3O4^?1 and per‐metal turnover frequency of 0.38–0.62 s^?1 at an overpotential of 400 mV in 1 m NaOH aqueous solution. This mixed valent cobalt oxide structure exhibits excellent long‐term electrochemical and mechanical stability preserving the initial catalytic activity over more than 12 h of constant current electrolysis and 1000 consecutive voltammetric cycles. The potential of the Co₃O₄ nano‐islands for photoelectrochemical water splitting has been demonstrated by incorporation of co‐catalysts in GaN nanowire photoanodes. The Co₃O₄‐GaN photoanodes reveal significantly reduced onset overpotentials, improved photoresponse and photostability compared to the bare GaN ones. These findings provide a highly performing catalyst structure and a scalable synthesis method for the engineering of efficient photoanodes for integrated solar water‐splitting cells.     

3D Hierarchical Core–Shell Nanostructured Arrays on Carbon Fibers as Catalysts for Direct Urea Fuel Cells

Bifunctional cobalt oxide (Co₃O₄) nanowire catalysts grown on carbon cloth (CC) fibers and their modification with nickel oxide (NiO) and manganese dioxide (MnO₂) to produce core–shell nanoarchitectures are explored as catalysts for urea oxidation reaction and oxygen reduction reaction in direct urea fuel cells (DUFC). Based on a systematic electrochemical characterization of the catalyst, the as‐developed core–shell nanoarchitectures are optimized toward DUFC performance. Under alkaline conditions with an anion exchange membrane, the DUFC with a cell configuration of Co₃O₄@NiO(1:2)/CC(a|c)Co₃O₄@MnO₂(1:2)/CC exhibits a maximum power density of 33.8 mW cm^?2 with excellent durability for 120 h without any performance loss. Furthermore, the DUFC exhibits a maximum power density of 23.2 mW cm^?2 with human urine as a fuel. These findings offer an approach to convert human waste into treasure.     

High‐Performance Trifunctional Electrocatalysts Based on FeCo/Co2P Hybrid Nanoparticles for Zinc–Air Battery and Self‐Powered Overall Water Splitting

Currently, it is still a significant challenge to simultaneously boost various reactions by one electrocatalyst with high activity, excellent durability, as well as low cost. Herein, hybrid trifunctional electrocatalysts are explored via a facile one‐pot strategy toward an efficient oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER). The catalysts are rationally designed to be composed by FeCo nanoparticles encapsuled in graphitic carbon films, Co₂P nanoparticles, and N,P‐codoped carbon nanofiber networks. The FeCo nanoparticles and the synergistic effect from Co₂P and FeCo nanoparticles make the dominant contributions to the ORR, OER, and HER activities, respectively. Their bifunctional activity parameter (?E) for ORR and OER is low to 0.77 V, which is much smaller than those of most nonprecious metal catalysts ever reported, and comparable with state‐of‐the‐art Pt/C and RuO₂ (0.78 V). Accordingly, the as‐assembled Zn–air battery exhibits a high power density of 154 mW cm^?2 with a low charge–discharge voltage gap of 0.83 V (at 10 mA cm^?2) and excellent stability. The as‐constructed overall water‐splitting cell achieves a current density of 10 mA cm^?2 (at 1.68 V), which is comparable to the best reported trifunctional catalysts.     

Synergistically Tuning Water and Hydrogen Binding Abilities Over Co4N by Cr Doping for Exceptional Alkaline Hydrogen Evolution Electrocatalysis

Searching for highly efficient and cost‐effective electrocatalysts toward the hydrogen evolution reaction (HER) in alkaline electrolyte is highly desirable for the development of alkaline water splitting, but still remains a significant challenge. Herein, the rational design of Cr‐doped Co₄N nanorod arrays grown on carbon cloth (Cr–Co₄N/CC) that can efficiently catalyze the HER in alkaline media is reported. It displays outstanding performance, with the exceptionally small overpotential of 21 mV to obtain the current density of 10 mA cm^?2 and good stability in 1.0 m KOH, which is even better than the commercial Pt/C electrocatalyst, and much lower than most of the reported transition metal nitride‐based and other non‐noble metal‐based electrocatalysts toward the alkaline HER. Density functional theory (DFT) calculations and experimental results reveal that the Cr atoms not only act as oxophilic sites for boosting water adsorption and dissociation, but also modulate the electronic structure of Co₄N to endow optimized hydrogen binding abilities on Co atoms, thereby leading to accelerating both the alkaline Volmer and Heyrovsky reaction kinetics. In addition, this strategy can be extended to other metals (such as Mo, Mn, and Fe) doped Co₄N electrocatalysts, thus may open up a new avenue for the rational design of highly efficient transition metal nitride‐based HER catalysts and beyond.     

Amorphous Cobalt Boride (Co2B) as a Highly Efficient Nonprecious Catalyst for Electrochemical Water Splitting: Oxygen and Hydrogen Evolution

It is demonstrated that amorphous cobalt boride (Co₂B) prepared by the chemical reduction of CoCl₂ using NaBH₄ is an exceptionally efficient electrocatalyst for the oxygen evolution reaction (OER) in alkaline electrolytes and is simultaneously active for catalyzing the hydrogen evolution reaction (HER). The catalyst achieves a current density of 10 mA cm^?2 at 1.61 V on an inert support and at 1.59 V when impregnated with nitrogen‐doped graphene. Stable performance is maintained at 10 mA cm^?2 for at least 60 h. The optimized catalyst, Co₂B annealed at 500 °C (Co₂B‐500) evolves oxygen more efficiently than RuO₂ and IrO₂, and its performance matches the best cobalt‐based catalysts reported to date. Co₂B is irreversibly oxidized at OER conditions to form a CoOOH surface layer. The active form of the catalyst is therefore represented as CoOOH/Co₂B. EXAFS observations indicate that boron induces lattice strain in the crystal structure of the metal, which potentially diminishes the thermodynamic and kinetic barrier of the hydroxylation reaction, formation of the OOH* intermediate, a key limiting step in the OER.     

Hierarchical NiCo2S4@NiO Core–Shell Heterostructures as Catalytic Cathode for Long‐Life Li‐O2 Batteries

The critical challenges of Li‐O₂ batteries lie in sluggish oxygen redox kinetics and undesirable parasitic reactions during the oxygen reduction reaction and oxygen evolution reaction processes, inducing large overpotential and inferior cycle stability. Herein, an elaborately designed 3D hierarchical heterostructure comprising NiCo₂S₄@NiO core–shell arrays on conductive carbon paper is first reported as a freestanding cathode for Li‐O₂ batteries. The unique hierarchical array structures can build up multidimensional channels for oxygen diffusion and electrolyte impregnation. A built‐in interfacial potential between NiCo₂S₄ and NiO can drastically enhance interfacial charge transfer kinetics. According to density functional theory calculations, intrinsic LiO₂‐affinity characteristics of NiCo₂S₄ and NiO play an importantly synergistic role in promoting the formation of large peasecod‐like Li₂O₂, conducive to construct a low‐impedance Li₂O₂/cathode contact interface. As expected, Li‐O₂ cells based on NiCo₂S₄@NiO electrode exhibit an improved overpotential of 0.88 V, a high discharge capacity of 10 050 mAh g^?1 at 200 mA g^?1, an excellent rate capability of 6150 mAh g^?1 at 1.0 A g^?1, and a long‐term cycle stability under a restricted capacity of 1000 mAh g^?1 at 200 mA g^?1. Notably, the reported strategy about heterostructure accouplement may pave a new avenue for the effective electrocatalyst design for Li‐O₂ batteries.     

Multifunctional Single‐Crystallized Carbonate Hydroxides as Highly Efficient Electrocatalyst for Full Water splitting

The controllable synthesis of single‐crystallized iron‐cobalt carbonate hydroxide nanosheets array on 3D conductive Ni foam (FCCH/NF) as a monolithic oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) bifunctional electrocatalyst for full water splitting is described. The results demonstrate that the incorporation of Fe can effectively tune the morphology, composition, electronic structure, and electrochemical active surface area of the electrocatalysts, thus greatly enhancing the intrinsic electrocatalytic activity. The optimal electrocatalyst (F_0.25C₁CH/NF) can deliver 10 and 1000 mA cm^?2 at very small overpotentials of 77 and 256 mV for HER and 228 and 308 mV for OER in 1.0 m KOH without significant interference from gas evolution. The F_0.25C₁CH‐based two‐electrode alkaline water electrolyzer only requires cell voltages of 1.45 and 1.52 V to achieve current densities of 10 and 500 mA cm^?2. The results demonstrate that such fascinating electrocatalytic activity can be ascribed to the increase in the catalytic active surface area, facilitated electron and mass transport properties, and the synergistic interactions because of the incorporation of Fe.     

Highly‐Tunable Nickel Cobalt Oxide as a Low‐Temperature P‐Type Contact in Organic Photovoltaic Devices

We report on the investigation of nickel cobalt oxide (Ni_xCo_3?xO₄) thin films grown by pulsed laser deposition as hole‐transport interlayers (HTL) in organic photovoltaic (OPV) devices. Films of 7 nm thickness were grown under various oxygen deposition pressures (pO₂) in the range of 2–200 mTorr. We explore both bulk and surface properties of these thin films. The workfunction (?) for each of the films was statistically similar (～4.7 eV), regardless of pO₂. There was not a strong dependence of the power conversion efficiency (η) on the conductivities of the HTLs varying between 0.009 ‐ 10 S/cm. The observed differences in OPV efficiencies (ranging from 1.16 to 2.46%) were correlated to the near surface chemical composition of the Ni_xCo_3?xO₄ HTL, as observed by differences in the relative surface hydroxyl concentration. The critical role of the near‐surface composition of the HTL at the HTL/organic interface was further explored by modifying the hydroxyl concentration using an oxygen plasma treatment. This treatment mitigated the impact of surface hydroxyl coverage, demonstrating either identical or increased values for ? and η, regardless of initial pO₂ in the creation of the Ni_xCo_3?xO₄ HTL. To further explore this we also employed a phosphonic acid surface modification agent on the HTL, increasing ? to 5.2 eV producing the best η value of 3.4%, equivalent to the PEDOT:PSS control devices. These results indicate that nickel cobalt oxide is a promising p‐type oxide for carrier‐selective interlayers in organic solar cells; however, for this to be fully realized the specific surface chemistry at the oxide/polymer interface must be controlled to increase ? and optimize device performance.     

Nitrogen and Sulfur Vacancies in Carbon Shell to Tune Charge Distribution of Co6Ni3S8 Core and Boost Sodium Storage

Recently, the metal sulfide‐carbon nanocomposites have been suggested as a low‐cost alternative to lithium ion batteries, but commercial application is seriously hindered by their relatively inferior cyclic performance. Herein, N and S vacancies in an N,S co‐doped carbon (NSC) shell for anchoring a new bimetallic sulfide core of Co₆Ni₃S₈ using Co‐Ni‐alginate biomass are introduced. The obtained Co₆Ni₃S₈/carbon aerogels (Co₆Ni₃S₈/NSCA) exhibit excellent sodium‐ion storage properties, high reversible capacity (568.1 mAh g^?1 at 1 A g^?1), and an excellent cycle stability (94.4% after 300 cycles). Density functional theory calculation results disclose that nitrogen and sulfur vacancies in the carbon shell can enhance the binding between the Co₆Ni₃S₈ core and NSC shell, ensuring an improved structural and electrochemical stability. In addition, an increased adsorption energy of Na⁺ (?1.88 eV) and a decreased barrier energy for Na⁺ diffusion (0.46 eV) are observed indicating a fast Na⁺ diffusion process. The powder X‐ray diffraction refinement confirms that the lattice parameters of Co₆Ni₃S₈ extend to 0.9972 nm compared with Co₉S₈ (0.9928 nm), suppressing the volume expansion in Na⁺ diffusion processes.     

Synthesis and Operando Sodiation Mechanistic Study of Nitrogen‐Doped Porous Carbon Coated Bimetallic Sulfide Hollow Nanocubes as Advanced Sodium Ion Battery Anode

Due to the obvious advantages of utilizing naturally abundant and low cost sodium resources, sodium ion batteries (SIBs) show great potential for large‐scale energy storage applications. And the high theoretical capacities of transition metal sulfides (TMSs) make them appealing anode materials for SIBs; however, structural collapse caused by the severe volume change during de/sodiation processes results in poor capacity retention and rate capabilities. Compared to the development of new materials and the improvement of their electrochemical performance, the studies on their reaction mechanisms are still rare, especially the operando characterizations. Herein, the synthesis, anode application, and the operando observation of the de/sodiation mechanism of a nitrogen‐doped porous carbon coated nickel cobalt bimetallic sulfide hollow nanocube ((Ni_0.5Co_0.5)₉S₈@NC) composite are reported. Such a material is synthesized via facile sulfidation of phenol formaldehyde coated Ni₃[Co(CN)₆]₂ metal–organic framework precursors with Na₂S followed by calcination. The nanocomposite displays a remarkable specific capacity of 752 mAh g^?1 at 100 mA g^?1 after 100 cycles and outstanding rate capability due to the synergistic effect of several appealing features. Particularly, the pseudocapacitive effect appears to substantially contribute to the sodium storage capability. Operando X‐ray diffraction reveals the conversion reaction mechanism of (Ni_0.5Co_0.5)₉S₈@NC, forming Ni, Co, Na₂S, and Na₂S₅.