In Situ Mechanistic Elucidation of Superior Si‐C‐Graphite Li‐Ion Battery Anode Formation with Thermal Safety Aspects

A composite anode material synthesized using silicon nanoparticles, micrometer sized graphite particles, and starch‐derived amorphous carbon (GCSi) offers scalability and enhanced electrochemical performance when compared to existing graphite anodes. Mechanistic elucidation of the formation steps of tailored GCSi composite are achieved with environmental transmission electron microscopy (ETEM) and thermal safety aspects of the composite anode are studied for the first time using specially designed multimode calorimetry for coin cell studies. Electrochemical analysis of the composite anode demonstrates a high initial discharge capacity (1126 mAh g^?1) and yields a high coulombic efficiency of 83% in the first charge cycle. Applying a current density of 500 mA g^?1, the anode composite retains 448 mAh g^?1 specific capacity after 100 cycles. Cycling stability is a result of improved interfacial binding made possible by the interconnected architecture of wheat derived amorphous carbon, enhancing the electrochemical kinetics and decreasing the inherent issues associated with volume expansion and pulverization of pristine Si electrodes. Comparing the energy released during thermal runaway, per specific capacity for the full‐cell, the GCSi composite releases less heat than the conventional graphitic anode, suggesting a synergistic effect of each ingredient of the GCSi composite, providing a safer and higher performing anode.     

Improved Electrochemical Performance of Na‐Ion Batteries in Ether‐Based Electrolytes: A Case Study of ZnS Nanospheres

Sodium‐ion batteries are considered as a promising technology for large‐scale energy storage applications, owing to their low cost. However, there are many challenges for developing sodium‐ion batteries with high capacity, long cycle life, and high‐rate capability. Herein, the development of high‐performance sodium‐ion batteries using ZnS nanospheres as anode material and an ether‐based electrolyte, which exhibit improved electrochemical performance over the pure alkyl carbonate electrolytes, is reported. ZnS nanospheres deliver a high specific capacity of 1000 mA h g^?1 and high initial Columbic efficiency of 90%. Electrochemical testing and first‐principle calculations demonstrate that the ether‐based solvent can facilitate charge transport, reduce the energy barrier for sodium‐ion diffusion, and thus enhance electrochemical performances. Ex situ measurements (X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS) mapping) reveal that ZnS nanospheres maintain structural integrity during the charge and discharge processes over 100 cycles. As anode material for sodium‐ion batteries, ZnS nanospheres deliver high reversible sodium storage capacity, high Coulombic efficiencies, and extended cycle life.     

Heteroatom‐Doped Mesoporous Hollow Carbon Spheres for Fast Sodium Storage with an Ultralong Cycle Life

Carbon materials have attracted significant attention as anode materials for sodium ion batteries (SIBs). Developing a carbon anode with long‐term cycling stability under ultrahigh rate is essential for practical application of SIBs in energy storage systems. Herein, sulfur and nitrogen codoped mesoporous hollow carbon spheres are developed, exhibiting high rate performance of 144 mA h g^?1 at 20 A g^?1, and excellent cycling durability under ultrahigh current density. Interestingly, during 7000 cycles at a current density of 20 A g^?1, the capacity of the electrode gradually increases to 180 mA h g^?1. The mechanisms for the superior electrochemical performance and capacity improvement of the cells are studied by electrochemical tests, ex situ transmission electron microscopy, X‐ray diffraction, X‐ray photoelectron spectroscopy, and Raman analysis of fresh and cycled electrodes. The unique and robust structure of the material can enhance transport kinetics of electrons and sodium ions, and maintain fast sodium storage from the capacitive process under high rate. The self‐rearrangement of the carbon structure, induced by continuous discharge and charge, lead to the capacity improvement with cycles. These results demonstrate a new avenue to design advanced anode materials for SIBs.     

Nature of FeSe2/N‐C Anode for High Performance Potassium Ion Hybrid Capacitor

Potassium ion hybrid capacitors have great potential for large‐scale energy devices, because of the high power density and low cost. However, their practical applications are hindered by their low energy density, as well as electrolyte decomposition and collector corrosion at high potential in potassium bis(fluoro‐sulfonyl)imide‐based electrolyte. Therefore, anode materials with high capacity, a suitable voltage platform, and stability become a key factor. Here, N‐doping carbon‐coated FeSe₂ clusters are demonstrated as the anode material for a hybrid capacitor, delivering a reversible capacity of 295 mAh g^?1 at 100 mA g^?1 over 100 cycles and a high rate capability of 158 mAh g^?1 at 2000 mA g^?1 over 2000 cycles. Meanwhile, through density functional theory calculations, in situ X‐ray diffraction, and ex situ transmission electron microscopy, the evolution of FeSe₂ to Fe₃Se₄ for the electrochemical reaction mechanism is successfully revealed. The battery‐supercapacitor hybrid using commercial activated carbon as the cathode and FeSe₂/N‐C as the anode is obtained. It delivers a high energy density of 230 Wh kg^?1 and a power density of 920 W kg^?1 (the energy density and power density are calculated based on the total mass of active materials in the anode and cathode).     

Insights into the Na+ Storage Mechanism of Phosphorus‐Functionalized Hard Carbon as Ultrahigh Capacity Anodes

Hard carbon as a typical anode material for sodium ion batteries has received much attention in terms of its low cost and renewability. Herein, phosphorus‐functionalized hard carbon with a specific “honeycomb briquette” shaped morphology is synthesized via electrospinning technology. When applied as an anode material for Na⁺ storage, it exhibits an impressively high reversible capacity of 393.4 mA h g^?1 with the capacity retention up to 98.2% after 100 cycles. According to first‐principle calculation, the ultrahigh capacity of the as‐prepared anode is ascribed to the enhancement of Na‐absorption through formation of P?O and P? C bonds in graphitic layers when doped with phosphorus. Moreover, the increase of electron density around the Fermi level is found to be mainly caused by O atoms instead of P atoms.     

Bottom‐Up Confined Synthesis of Nanorod‐in‐Nanotube Structured Sb@N‐C for Durable Lithium and Sodium Storage

Antimony (Sb) has emerged as an attractive anode material for both lithium and sodium ion batteries due to its high theoretical capacity of 660 mA h g^?1. In this work, a novel peapod‐like N‐doped carbon hollow nanotube encapsulated Sb nanorod composite, the so‐called nanorod‐in‐nanotube structured Sb@N‐C, via a bottom‐up confinement approach is designed and fabricated. The N‐doped‐carbon coating and thermal‐reduction process is monitored by in situ high‐temperature X‐ray diffraction characterization. Due to its advanced structural merits, such as sufficient N‐doping, 1D conductive carbon coating, and substantial inner void space, the Sb@N‐C demonstrates superior lithium/sodium storage performance. For lithium storage, the Sb@N‐C exhibits a high reversible capacity (650.8 mA h g^?1 at 0.2 A g^?1), excellent long‐term cycling stability (a capacity decay of only 0.022% per cycle for 3000 cycles at 2 A g^?1), and ultrahigh rate capability (343.3 mA h g^?1 at 20 A g^?1). For sodium storage, the Sb@N‐C nanocomposite displays the best long‐term cycle performance among the reported Sb‐based anode materials (a capacity of 345.6 mA h g^?1 after 3000 cycles at 2 A g^?1) and an impressive rate capability of up to 10 A g^?1. The results demonstrate that the Sb@N‐C nanocomposite is a promising anode material for high‐performance lithium/sodium storage.     

Mn‐Rich P′2‐Na0.67[Ni0.1Fe0.1Mn0.8]O2 as High‐Energy‐Density and Long‐Life Cathode Material for Sodium‐Ion Batteries

Herein, P′2‐type Na_0.67[Ni_0.1Fe_0.1Mn_0.8]O₂ is introduced as a promising new cathode material for sodium‐ion batteries (SIBs) that exhibits remarkable structural stability during repetitive Na⁺ de/intercalation. The O? Ni? O? Mn? O? Fe? O bond in the octahedra of transition‐metal layers is used to suppress the elongation of the Mn? O bond and to improve the electrochemical activity, leading to the highly reversible Na storage mechanism. A high discharge capacity of ≈220 mAh g^?1 (≈605 Wh kg^?1) is delivered at 0.05 C (13 mAg^?1) with a high reversible capacity of ≈140 mAh g^?1 at 3 C and excellent capacity retention of 80% over 200 cycles. This performance is associated with the reversible P′2–OP4 phase transition and small volume change upon charge and discharge (≈3%). The nature of the sodium storage mechanism in a full cell paired with a hard carbon anode reveals an unexpectedly high energy density of ≈542 Wh kg^?1 at 0.2 C and good capacity retention of ≈81% for 500 cycles at 1 C (260 mAg^?1).     

One‐Step Solvothermal Synthesis of Nanostructured Manganese Fluoride as an Anode for Rechargeable Lithium‐Ion Batteries and Insights into the Conversion Mechanism

A nanostructured manganese fluoride is successfully synthesized for the first time through a facile one‐step solvothermal method. Ionic liquid (IL) 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BmimBF₄) as fluorine source and manganese (II) acetate tetrahydrate (Mn(CH₃COO)₂·4H₂O) as manganese source are used. By controlling the amount of manganese source and both the reaction time and temperature, pure phase tetragonal MnF₂ with a uniformly distributed nanocrystalline of 100–300 nm can be obtained. A possible formation mechanism related to the role of the IL is proposed. Electrochemical performance of MnF₂ nanocrystals as anodes for rechargeable lithium batteries is investigated. A low discharge plateau around 0.6 V at 0.1 C of the first cycle is obtained for lithium uptake reactions with a reversible discharge capacity as high as 300 mAh g^?1. The new MnF₂ anode is found to deliver significantly improved cycling performance than conventional conversion reaction electrodes with a capacity retention of 237 mAh g^?1 at 10 C even after 5000 cycles, indicating its promising utilization as anode material for future lithium‐ion batteries with long cycle life. High‐resolution transmission electron microscopy and X‐ray photoelectron spectroscopy analyses for lithiated and delithiated MnF₂ electrodes are used to reveal the conversion mechanism for the reversible electrochemical reaction of MnF₂ with Li.     

Characterization of electrochemical activity of a strain ISO2‐3 phylogenetically related to Aeromonas sp. isolated from a glucose‐fed microbial fuel cell

The microbial communities associated with electrodes in closed and open circuit microbial fuel cells (MFCs) fed with glucose were analyzed by 16S rRNA approach and compared. The comparison revealed that bacteria affiliated with the Aeromonas sp. within the Gammaproteobacteria constituted the major population in the closed circuit MFC (harvesting electricity) and considered to play important roles in current generation. We, therefore, attempted to isolate the dominant bacteria from the anode biofilm, successfully isolated a Fe (III)‐reducing bacterium phylogenetically related to Aeromonas sp. and designated as strain ISO2‐3. The isolated strain ISO2‐3 could grow and concomitantly produce current (max. 0.24 A/m²) via oxidation of glucose or hydrogen with an electrode serving as the sole electron acceptor. The strain could ferment glucose, but generate less electrical current. Cyclic voltammetry supported the strain ISO2‐3 was electrically active and likely to transfer electrons to the electrode though membrane‐associated compounds (most likely c‐type cytochrome). This mechanism requires intimate contact with the anode surface. Scanning electron microscopy revealed that the strain ISO2‐3 developed multiplayer biofilms on the anode surface and also produced anchor‐like filamentous appendages (most likely pili) that may promote long‐range electron transport across the thick biofilm. Biotechnol. Bioeng. 2009; 104: 901–910. © 2009 Wiley Periodicals, Inc.     

Na‐Mn‐O Nanocrystals as a High Capacity and Long Life Anode Material for Li‐Ion Batteries

Searching for a new material to build the next‐generation rechargeable lithium‐ion batteries (LIBs) with high electrochemical performance is urgently required. Owing to the low‐cost, non‐toxicity, and high‐safety, the family of manganese oxide including the Na‐Mn‐O system is regarded as one of the most promising electrode materials for LIBs. Herein, a new strategy is carried out to prepare a highly porous and electrochemically active Na_0.55Mn₂O₄·1.5H₂O (SMOH) compound. As an anode material, the Na‐Mn‐O nanocrystal material dispersed within a carbon matrix manifests a high reversible capacity of 1015.5 mA h g^?1 at a current density of 0.1 A g^?1. Remarkably, a considerable capability of 546.8 mA h g^?1 remains even after 2000 discharge/charge cycles at the higher current density of 4 A g^?1, indicating a splendid cyclability. The exceptional electrochemical properties allow SMOH to be a promising anode material toward LIBs.     

Tailored Plum Pudding‐Like Co2P/Sn Encapsulated with Carbon Nanobox Shell as Superior Anode Materials for High‐Performance Sodium‐Ion Capacitors

Sodium‐ion capacitors (SICs) are emerging energy storage devices with high energy, high power, and durable life. Sn is a promising anode material for lithium storage, but the poor conductivity of the a‐NaSn phase upon sodaition hinders its implementation in SICs. Herein, a superior Sn‐based anode material consisting of plum pudding‐like Co₂P/Sn yolk encapsulated with nitrogen‐doped carbon nanobox (Co₂P/Sn@NC) for high‐performance SICs is reported. The 8–10 nm metallic nanoparticles produced in situ are uniformly dispersed in the amorphous Sn matrix serving as conductive fillers to facilitate electron transfer in spite of the formation of electrically resistive a‐NaSn phase during cycling. Meanwhile, the carbon shell buffers the large expansion of active Sn and provides a stable electrode–electrolyte interface. Owing to these merits, the yolk–shell Co₂P/Sn@NC demonstrates a large capacity of 394 mA h g^?1 at 100 mA g^?1, high rate capability of 168 mA h g^?1 at 5000 mA g^?1, and excellent cyclability with 87% capacity retention after 10 000 cycles. By integrating the Co₂P/Sn@NC anode with a peanut shell‐derived carbon cathode in the SIC, high energy densities of 112.3 and 43.7 Wh kg^?1 at power densities of 100 and 10 000 W kg^?1 are achieved.     

Enhanced Ion Conductivity in Conducting Polymer Binder for High‐Performance Silicon Anodes in Advanced Lithium‐Ion Batteries

Polymer binders with high ion and electron conductivities are prepared by assembling ionic polymers (polyethylene oxide and polyethylenimine) onto the electrically conducting polymer poly(3,4‐ethylenedioxythiophene): poly(styrenesulfonate) chains. Crosslinking, chemical reductions, and electrostatics increase the modulus of the binders and maintain the integrity of the anode. The polymer binder shows lithium‐ion diffusivity and electron conductivity that are 14 and 90 times higher than those of the widely used carboxymethyl cellulose (with acetylene black) binder, respectively. The silicon anode with the polymer binder has a high reversible capacity of over 2000 mA h g^?1 after 500 cycles at a current density of 1.0 A g^?1 and maintains a superior capacity of 1500 mA h g^?1 at a high current density of 8.0 A g^?1.     

Rational Construction of Self‐Standing Sulfur‐Doped Fe2O3 Anodes with Promoted Energy Storage Capability for Wearable Aqueous Rechargeable NiCo‐Fe Batteries

Aqueous rechargeable Ni‐Fe batteries featuring an ultra‐flat discharge plateau, low cost, and outstanding safety characteristics show promising prospects for application in wearable energy storage. In particular, fiber‐shaped Ni‐Fe batteries will enable textile‐based energy supply for wearable electronics. However, the development of fiber‐shaped Ni‐Fe batteries is currently challenged by the performance of fibrous Fe‐based anode materials. In this context, this study describes the fabrication of sulfur‐doped Fe₂O₃ nanowire arrays (S‐Fe₂O₃ NWAs) grown on carbon nanotube fibers (CNTFs) as an innovative anode material (S‐Fe₂O₃ NWAs/CNTF). Encouragingly, first‐principle calculations reveal that S‐doping in Fe₂O₃ can dramatically reduce the band gap from 2.34 to 1.18 eV and thus enhance electronic conductivity. The novel developed S‐Fe₂O₃ NWAs/CNTF electrode is further demonstrated to deliver a very high capacity of 0.81 mAh cm^?2 at 4 mA cm^?2. This value is almost sixfold higher than that of the pristine Fe₂O₃ NWAs/CNTF electrode. When a cathode containing zinc‐nickel‐cobalt oxide (ZNCO)@Ni(OH)₂ NWAs heterostructures is used, 0.46 mAh cm^?2 capacity and 67.32 mWh cm^?3 energy density are obtained for quasi‐solid‐state fiber‐shaped NiCo‐Fe batteries, which outperform most state‐of‐the‐art fiber‐shaped aqueous rechargeable batteries. These findings offer an innovative and feasible route to design high‐performance Fe‐based anodes and may inspire new development for the next‐generation wearable Ni‐Fe batteries.     

S‐Doped Graphene‐Regional Nucleation Mechanism for Dendrite‐Free Lithium Metal Anodes

Lithium metal is the most promising anode material for next‐generation batteries, owing to its high theoretical specific capacity and low electrochemical potential. However, the practical application of lithium metal batteries (LMBs) has been plagued by the issues of uncontrollable lithium deposition. The multifunctional nanostructured anode can modulate the initial nucleation process of lithium before the extension of dendrites. By combing the theoretical design and experimental validation, a novel nucleation strategy is developed by introducing sulfur (S) to graphene. Through first‐principles simulations, it is found that S atom doping can improve the Li adsorption ability on a large area around the S doping positions. Consequently, S‐doped graphene with five lithiophilic sites rather than a single atomic site can serve as the pristine nucleation area, reducing the uneven Li deposition and improving the electrochemical performance. Modifying Li metal anodes by S‐doped graphene enables an ultralow overpotential of 5.5 mV, a high average Coulombic efficiency of 99% over more than 180 cycles at a current density of 0.5 mA cm^?2 for 1.0 mAh cm^?2, and a high areal capacity of 3 mAh cm^?2. This work sheds new light on the rational design of nucleation area materials for dendrite‐free LMB.     

Elucidating the Effect of Iron Doping on the Electrochemical Performance of Cobalt‐Free Lithium‐Rich Layered Cathode Materials

The eco‐friendly and low‐cost Co‐free Li_1.2Mn_0.585Ni_0.185Fe_0.03O₂ is investigated as a positive material for Li‐ion batteries. The electrochemical performance of the 3 at% Fe‐doped material exhibits an optimal performance with a capacity and voltage retention of 70 and 95%, respectively, after 200 cycles at 1C. The effect of iron doping on the electrochemical properties of lithium‐rich layered materials is investigated by means of in situ X‐ray diffraction spectroscopy and galvanostatic intermittent titration technique during the first charge–discharge cycle while high‐resolution transmission electron microscopy is used to follow the structural and chemical change of the electrode material upon long‐term cycling. By means of these characterizations it is concluded that iron doping is a suitable approach for replacing cobalt while mitigating the voltage and capacity degradation of lithium‐rich layered materials. Finally, complete lithium‐ion cells employing Li_1.2Mn_0.585Ni_0.185Fe_0.03O₂ and graphite show a specific energy of 361 Wh kg^?1 at 0.1C rate and very stable performance upon cycling, retaining more than 80% of their initial capacity after 200 cycles at 1C rate. These results highlight the bright prospects of this material to meet the high energy density requirements for electric vehicles.     

Lithiophilic CuO Nanoflowers on Ti‐Mesh Inducing Lithium Lateral Plating Enabling Stable Lithium‐Metal Anodes with Ultrahigh Rates and Ultralong Cycle Life

Lithium (Li) metal anodes are promising candidates for high‐energy‐density batteries. However, uncontrollable dendritic plating behavior and infinite volume expansion are hindering their practical applications. Herein, a novel CuO@Ti‐mesh (CTM) is prepared by microwave‐assisted reactions, followed by pressing on Li wafers, leading to Li/CuO@Ti‐mesh (LCTM) composite anodes. The lithiophilic CuO nanoflowers on Ti‐mesh provides evenly distributed nucleation sites, inducing uniform Li‐ion lateral plating, which can effectively inhibit the growth of Li dendrites and volume expansion during cycling. The as‐prepared LCTM composite anode exhibits high Coulombic efficiency (CE) of 94.2% at 10 mA cm^‐2 over 90 cycles. Meanwhile, the LCTM anode shows a low overpotential of 50 mV at 10 mA cm^‐2 over 16 000 cycles and a low overpotential of 90 and 250 mV even at ultrahigh current densities of 20 and 40 mA cm^‐2. When paired with Li₄Ti₅O₁₂ (LTO), it enhances the capacity retention of LTO/Li wafer full cells by about two times from 36.6% to 73.0% and 42.0% to 80.0% at 5C and 10C with long‐term cycling. It is hoped that this LCTM anode with ultrahigh rates and ultralong cycle life may put Li‐metal anode forward to practical applications, such as in Li–S, Li‐air batteries, etc.     

Hierarchically Porous N‐Doped Carbon Fibers as a Free‐Standing Anode for High‐Capacity Potassium‐Based Dual‐Ion Battery

Potassium‐based dual‐ion batteries (KDIBs) have emerged as a new generation of rechargeable batteries, due to their high cell voltage, low cost, and the natural abundance of potassium resources. However, the low capacity and poor cycling stability largely hinder the further development of KDIBs. Herein, the fabrication of hierarchically porous N‐doped carbon fibers (HPNCFs) as a free‐standing anode for high‐performance KDIBs is reported. With a free‐standing hierarchical structure (micro/meso/macropores and nanochannels) and high‐content of nitrogen doping, the HPNCFs not only provide intrinsic electron pathways and efficient ion transport channels, but also afford sufficient free space to tolerate the volume change during cycling. Consequently, the KDIBs made from a graphite cathode and an optimized HPNCFs anode deliver a high reversible capacity of 197 mAh g^?1 at a specific current of 50 mA g^?1, and excellent cycling stability (65 mAh g^?1 after 346 cycles at a specific current of 100 mA g^?1, the capacity calculation of the KDIBs is based on the mass of the anode). These results indicate that the properly designed HPNCFs can effectively improve the capacity and cycling stability of the KDIBs, indicating a great potential for applications in the field of high‐performance energy‐storage devices.     

Nanosheets‐Assembled CuSe Crystal Pillar as a Stable and High‐Power Anode for Sodium‐Ion and Potassium‐Ion Batteries

Thanks to low costs and the abundance of the resources, sodium‐ion (SIBs) and potassium‐ion batteries (PIBs) have emerged as leading candidates for next‐generation energy storage devices. So far, only few materials can serve as the host for both Na⁺ and K⁺ ions. Herein, a cubic phase CuSe with crystal‐pillar‐like morphology (CPL‐CuSe) assembled by the nanosheets are synthesized and its dual functionality in SIBs and PIBs is comprehensively studied. The electrochemical measurements demonstrate that CPL‐CuSe enables fast Na⁺ and K⁺ storage as well as the sufficiently long duration. Specifically, the anode delivers a specific capacity of 295 mA h g^?1 at current density of 10 A g^?1 in SIBs, while 280 mA h g^?1 at 5 A g^?1 in PIBs, as well as the high capacity retention of nearly 100% over 1200 cycles and 340 cycles, respectively. Remarkably, CPL‐CuSe exhibits a high initial coulombic efficiency of 91.0% (SIBs) and 92.4% (PIBs), superior to most existing selenide anodes. A combination of in situ X‐ray diffraction and ex situ transmission electron microscopy tests fundamentally reveal the structural transition and phase evolution of CuSe, which shows a reversible conversion reaction for both cells, while the intermediate products are different due to the sluggish K⁺ insertion reaction.     

Ice Templated Free‐Standing Hierarchically WS2/CNT‐rGO Aerogel for High‐Performance Rechargeable Lithium and Sodium Ion Batteries

A hybrid nanoarchitecture aerogel composed of WS₂ nanosheets and carbon nanotube‐reduced graphene oxide (CNT‐rGO) with ordered microchannel three‐dimensional (3D) scaffold structure was synthesized by a simple solvothermal method followed by freeze‐drying and post annealing process. The 3D ordered microchannel structures not only provide good electronic transportation routes, but also provide excellent ionic conductive channels, leading to an enhanced electrochemical performance as anode materials both for lithium‐ion batteries (LIBs) and sodium‐ion batteries (SIBs). Significantly, WS₂/CNT‐rGO aerogel nanostructure can deliver a specific capacity of 749 mA h g^?1 at 100 mA g^?1 and a high first‐cycle coulombic efficiency of 53.4% as the anode material of LIBs. In addition, it also can deliver a capacity of 311.4 mA h g^?1 at 100 mA g^?1, and retain a capacity of 252.9 mA h g^?1 at 200 mA g^?1 after 100 cycles as the anode electrode of SIBs. The excellent electrochemical performance is attributed to the synergistic effect between the WS₂ nanosheets and CNT‐rGO scaffold network and rational design of 3D ordered structure. These results demonstrate the potential applications of ordered CNT‐rGO aerogel platform to support transition‐metal‐dichalcogenides (i.e., WS₂) for energy storage devices and open up a route for material design for future generation energy storage devices.     

Hollow CuS Nanoboxes as Li‐Free Cathode for High‐Rate and Long‐Life Lithium Metal Batteries

Transition metal sulfides hold promising potentials as Li‐free conversion‐type cathode materials for high energy density lithium metal batteries. However, the practical deployment of these materials is hampered by their poor rate capability and short cycling life. In this work, the authors take the advantage of hollow structure of CuS nanoboxes to accommodate the volume expansion and facilitate the ion diffusion during discharge–charge processes. As a result, the hollow CuS nanoboxes achieve excellent rate performance (≈371 mAh g^?1 at 20 C) and ultra‐long cycle life (>1000 cycles). The structure and valence evolution of the CuS nanobox cathode are identified by scanning electron microscopy, transmission electron microscopy, and X‐ray photoelectron spectroscopy. Furthermore, the lithium storage mechanism is revealed by galvanostatic intermittent titration technique and operando Raman spectroscopy for the initial charge–discharge process and the following reversible processes. These results suggest that the hollow CuS nanobox material is a promising candidate as a low‐cost Li‐free cathode material for high‐rate and long‐life lithium metal batteries.