Identifying the Nature of Charge Recombination in Organic Solar Cells from Charge‐Transfer State Electroluminescence

Charge‐transfer (CT) state electroluminescence is investigated in several polymer:fullerene bulk heterojunction solar cells. The ideality factor of the electroluminescence reveals that the CT emission in polymer:fullerene solar cells originates from free‐carrier bimolecular recombination at the donor‐acceptor interface, rather than a charge‐trap‐mediated process. The fingerprint of the presence of nonradiative trap‐assisted recombination, a voltage‐dependent CT electroluminescence quantum efficiency, is only observed for the P3HT:PCBM system, which is explained by a reduction of the competing bimolecular recombination rate. These results are in agreement with measurements of the illumination‐intensity dependence of the open‐circuit voltage.     

Mixed Domains Enhance Charge Generation and Extraction in Bulk‐Heterojunction Solar Cells with Small‐Molecule Donors

The interplay between nanomorphology and efficiency of polymer‐fullerene bulk‐heterojunction (BHJ) solar cells has been the subject of intense research, but the generality of these concepts for small‐molecule (SM) BHJs remains unclear. Here, the relation between performance; charge generation, recombination, and extraction dynamics; and nanomorphology achievable with two SM donors benzo[1,2‐b:4,5‐b]dithiophene‐pyrido[3,4‐b]‐pyrazine BDT(PPTh₂)₂, namely SM1 and SM2, differing by their side‐chains, are examined as a function of solution additive composition. The results show that the additive 1,8‐diiodooctane acts as a plasticizer in the blends, increases domain size, and promotes ordering/crystallinity. Surprisingly, the system with high domain purity (SM1) exhibits both poor exciton harvesting and severe charge trapping, alleviated only slightly with increased crystallinity. In contrast, the system consisting of mixed domains and lower crystallinity (SM2) shows both excellent exciton harvesting and low charge recombination losses. Importantly, the onset of large, pure crystallites in the latter (SM2) system reduces efficiency, pointing to possible differences in the ideal morphologies for SM‐based BHJ solar cells compared with polymer‐fullerene devices. In polymer‐based systems, tie chains between pure polymer crystals establish a continuous charge transport network, whereas SM‐based active layers may in some cases require mixed domains that enable both aggregation and charge percolation to the electrodes.     

Domain Compositions and Fullerene Aggregation Govern Charge Photogeneration in Polymer/Fullerene Solar Cells

The complex microstructure of organic semiconductor mixtures continues to obscure the connection between the active layer morphology and photovoltaic device performance. For example, the ubiquitous presence of mixed phases in the active layer of polymer/fullerene solar cells creates multiple morphologically distinct interfaces which are capable of exciton dissociation or charge recombination. Here, it is shown that domain compositions and fullerene aggregation can strongly modulate charge photogeneration at ultrafast timescales through studies of a model system, mixtures of a low band‐gap polymer, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]germole)‐2,6‐diyl‐alt‐(2,1,3‐benzothia‐diazole)‐4,7‐diyl], and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester. Structural characterization using energy‐filtered transmission electron microscopy (EFTEM) and resonant soft X‐ray scattering shows similar microstructures even with changes in the overall film composition. Composition maps generated from EFTEM, however, demonstrate that compositions of mixed domains vary significantly with overall film composition. Furthermore, the amount of polymer in the mixed domains is inversely correlated with device performance. Photoinduced absorption studies using ultrafast infrared spectroscopy demonstrate that polaron concentrations are highest when mixed domains contain the least polymer. Grazing‐incidence X‐ray scattering results show that larger fullerene coherence lengths are correlated to higher polaron yields. Thus, the purity of the mixed domains is critical for efficient charge photogeneration because purity modulates fullerene aggregation and electron delocalization.     

Relating Recombination,Density of States,and Device Performance in an Efficient Polymer:Fullerene Organic Solar Cell Blend

We explore the interrelation between density of states, recombination kinetics, and device performance in efficient poly[4,8‐bis‐(2‐ethylhexyloxy)‐benzo[1,2‐b:4,5‐b']dithiophene‐2,6‐diyl‐alt‐4‐(2‐ethylhexyloxy‐1‐one)thieno[3,4‐b]thiophene‐2,6‐diyl]:[6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PBDTTT‐C:PC₇₁BM) bulk‐heterojunction organic solar cells. We modulate the active‐layer density of states by varying the polymer:fullerene composition over a small range around the ratio that leads to the maximum solar cell efficiency (50–67 wt% PC₇₁BM). Using transient and steady‐state techniques, we find that nongeminate recombination limits the device efficiency and, moreover, that increasing the PC₇₁BM content simultaneously increases the carrier lifetime and drift mobility in contrast to the behavior expected for Langevin recombination. Changes in electronic properties with fullerene content are accompanied by a significant change in the magnitude or energetic separation of the density of localized states. Our comprehensive approach to understanding device performance represents significant progress in understanding what limits these high‐efficiency polymer:fullerene systems.     

Charge Carrier Dynamics of Polymer:Fullerene Blends: From Geminate to Non‐Geminate Recombination

The charge carrier dynamics of a new polymer‐fullerene blend are examined on the femtosecond to the millisecond time scale. The full time range is globally fitted using a chemical reaction rate model that includes all key processes, charge generation, energy transfer, charge separation, and recombination, over the full 12 orders of magnitude in time and a factor of 33 in light intensity. Particular attention is paid to the charge recombination processes and it is found that they are highly material specific. Comparison of the dynamics to those of a previously studied polymer:fullerene blend reveals that while for one blend the recombination dynamics are mainly controlled by geminate recombination, the charge recombination in the presently studied polymer:fullerene blend are entirely controlled by non‐geminate electron‐hole recombination. Carrier density dependence of the non‐geminate recombination rate is analyzed and a correlated disorder model of site energies is proposed to explain the observed dependency.     

Charge Transfer from Methylammonium Lead Iodide Perovskite to Organic Transport Materials: Efficiencies,Transfer Rates,and Interfacial Recombination

Perovskite‐based photovoltaics have been rapidly developed, with record power conversion efficiencies now exceeding 22%. In order to rationally design efficient and stable perovskite solar cells, it is important to understand not only charge trapping and recombination events, but also processes occurring at the perovskite/transport material (TM) interface, such as charge transfer and interfacial recombination. In this work, time‐resolved microwave conductivity measurements are performed to investigate these interfacial processes for methylammonium lead iodide and various state‐of‐the‐art organic TMs. A global kinetic model is developed, which accurately describes both the dynamics of excess charges in the perovskite layer and transfer to charge‐specific TMs. The authors conclude that for state‐of‐the‐art materials, such as Spiro‐OMeTAD and PCBM, the charge extraction efficiency is not significantly affected by intra‐band gap traps for trap densities under 10¹⁵ cm^–3. Finally, the transfer rates to C60, PCBM, EDOT‐OMeTPA, and Spiro‐OMeTAD are sufficient to outcompete second order recombination under excitation densities representative for illumination by AM1.5.     

Effect of Polymer Crystallinity in P3HT:PCBM Solar Cells on Band Gap Trap States and Apparent Recombination Order

The non‐geminate recombination of charge carriers in polymer‐fullerene solar cells has been modeled in the last few years with a trap‐assisted recombination model, which states that the apparent recombination order depends on the concentration of trapped charges tailing into the band gap. Higher concentrations of trapped charges lead to higher apparent recombination orders. In this work, the mass fraction f of highly crystalline nanofibrillar P3HT to the total P3HT content in P3HT:PCBM solar cells is consistently varied, controlling the temperature of a nanofibers‐P3HT casting dispersion. A systematic study of the apparent recombination order, measured with a transient photovoltage technique, as a function of f is presented. A correlation is shown between the apparent recombination order, the P3HT crystallinity, and the trap concentration in the band gap measured with an admittance spectroscopy technique.     

Polymer:Nonfullerene Bulk Heterojunction Solar Cells with Exceptionally Low Recombination Rates

Organic semiconductors are in general known to have an inherently lower charge carrier mobility compared to their inorganic counterparts. Bimolecular recombination of holes and electrons is an important loss mechanism and can often be described by the Langevin recombination model. Here, the device physics of bulk heterojunction solar cells based on a nonfullerene acceptor (IDTBR) in combination with poly(3‐hexylthiophene) (P3HT) are elucidated, showing an unprecedentedly low bimolecular recombination rate. The high fill factor observed (above 65%) is attributed to non‐Langevin behavior with a Langevin prefactor (β/β_L) of 1.9 × 10^?4. The absence of parasitic recombination and high charge carrier lifetimes in P3HT:IDTBR solar cells inform an almost ideal bimolecular recombination behavior. This exceptional recombination behavior is explored to fabricate devices with layer thicknesses up to 450 nm without significant performance losses. The determination of the photoexcited carrier mobility by time‐of‐flight measurements reveals a long‐lived and nonthermalized carrier transport as the origin for the exceptional transport physics. The crystalline microstructure arrangement of both components is suggested to be decisive for this slow recombination dynamics. Further, the thickness‐independent power conversion efficiency is of utmost technological relevance for upscaling production and reiterates the importance of understanding material design in the context of low bimolecular recombination.     

Reduced Recombination in High Efficiency Molecular Nematic Liquid Crystalline: Fullerene Solar Cells

Bimolecular recombination in bulk heterojunction organic solar cells is the process by which nongeminate photogenerated free carriers encounter each other, and combine to form a charge transfer (CT) state which subsequently relaxes to the ground state. It is governed by the diffusion of the slower and faster carriers toward the electron donor–acceptor interface. In an increasing number of systems, the recombination rate constant is measured to be lower than that predicted by Langevin's model for relative Brownian motion and the capture of opposite charges. This study investigates the dynamics of charge generation, transport, and recombination in a nematic liquid crystalline donor:fullerene acceptor system that gives solar cells with initial power conversion efficiencies of >9.5%. Unusually, and advantageously from a manufacturing perspective, these efficiencies are maintained in junctions thicker than 300 nm. Despite finding imbalanced and moderate carrier mobilities in this blend, strongly suppressed bimolecular recombination is observed, which is ≈150 times less than predicted by Langevin theory, or indeed, more recent and advanced models that take into account the domain size and the spatial separation of electrons and holes. The suppressed bimolecular recombination arises from the fact that ground‐state decay of the CT state is significantly slower than dissociation.     

Morphology‐Limited Free Carrier Generation in Donor/Acceptor Polymer Blend Solar Cells Composed of Poly(3‐hexylthiophene) and Fluorene‐Based Copolymer

The charge generation and recombination dynamics in polymer/polymer blend solar cells composed of poly(3‐hexylthiophene) (P3HT, electron donor) and poly[2,7‐(9,9‐didodecylfluorene)‐alt‐5,5‐(4′,7′‐bis(2‐thienyl)‐2′,1′,3′‐benzothiadiazole)] (PF12TBT, electron acceptor) are studied by transient absorption measurements. In the unannealed blend film, charge carriers are efficiently generated from polymer excitons, but some of them recombine geminately. In the blend film annealed at 160 °C, on the other hand, the geminate recombination loss is suppressed and hence free carrier generation efficiency increases up to 74%. These findings suggest that P3HT and PF12TBT are intermixed within a few nanometers, resulting in impure PF12TBT and disordered P3HT domains. The geminate recombination is likely due to charge carriers generated on isolated polymer chains in the matrix of the other polymer and at the domain interface with disordered P3HT. The undesired charge loss by geminate recombination is reduced by both the purification of the PF12TBT‐rich domain and crystallization of the P3HT chains. These results show that efficient free carrier generation is not inherent to the polymer/fullerene domain interface, but is possible with polymer/polymer systems composed of crystalline donor and amorphous acceptor polymers, opening up a new potential method for the improvement of solar cell materials.     

Understanding Triplet Formation Pathways in Bulk Heterojunction Polymer:Fullerene Photovoltaic Devices

Triplet exciton (TE) formation pathways are systematically investigated in prototype bulk heterojunction (BHJ) “super yellow” poly(p‐phenylene vinylene) (SY‐PPV) solar cell devices with varying fullerene compositions using complementary optoelectrical and electrically detected magnetic resonance (EDMR) spectroscopies. It is shown that EDMR spectroscopy allows the unambiguous demonstration of fullerene triplet production in BHJ polymer:fullerene solar cells. EDMR triplet detection under selective photoexcitation of each blend component and of the interfacial charge transfer (CT) state reveals that low lying fullerene TEs are produced by direct intersystem crossing from singlet excitons (SEs). The direct CT‐TE recombination pathway, although energetically feasible, is kinetically suppressed in these devices. However, high energy CT states in the CT manifold can contribute to the population of the fullerene triplet state via a direct CT‐SE conversion. This undesirable energetic alignment could be one of the causes for the severe reduction in photocurrent observed when the open‐circuit voltage of polymer:fullerene solar cells is pushed to 1.0 V or beyond.     

Suppression of Recombination Losses in Polymer:Nonfullerene Acceptor Organic Solar Cells due to Aggregation Dependence of Acceptor Electron Affinity

Here, it is investigated whether an energetic cascade between mixed and pure regions assists in suppressing recombination losses in non‐fullerene acceptor (NFA)‐based organic solar cells. The impact of polymer‐NFA blend composition upon morphology, energetics, charge carrier recombination kinetics, and photocurrent properties are studied. By changing film composition, morphological structures are varied from consisting of highly intermixed polymer‐NFA phases to consisting of both intermixed and pure phase. Cyclic voltammetry is employed to investigate the impact of blend morphology upon NFA lowest unoccupied molecular orbital (LUMO) level energetics. Transient absorption spectroscopy reveals the importance of an energetic cascade between mixed and pure phases in the electron–hole dynamics in order to well separate spatially localized electron–hole pairs. Raman spectroscopy is used to investigate the origin of energetic shift of NFA LUMO levels. It appears that the increase in NFA electron affinity in pure phases relative to mixed phases is correlated with a transition from a relatively planar backbone structure of NFA in pure, aggregated phases, to a more twisted structure in molecularly mixed phases. The studies focus on addressing whether aggregation‐dependent acceptor LUMO level energetics are a general design requirement for both fullerene and NFAs, and quantifying the magnitude, origin, and impact of such energetic shifts upon device performance.     

Domain Purity,Miscibility, and Molecular Orientation at Donor/Acceptor Interfaces in High Performance Organic Solar Cells: Paths to Further Improvement

Domain purity and interface structure are known to be critical for fullerene‐based bulk heterojunction (BHJ) solar cells, yet have been very difficult to study. Using novel soft X‐ray tools, we delineate the importance of these parameters by comparing high performance cells based on a novel naphtha[1,2‐c:5,6‐c]bis[1,2,5]thiadiazole (NT) material to cells based on a 2,1,3‐benzothiadiazole (BT) analogue. BT‐based devices exhibit ～15 nm, mixed domains that differ in composition by at most 22%, causing substantial bimolecular recombination. In contrast, NT‐based devices have more pure domains that are >80 nm in size, yet the polymer‐rich phase still contains at least 22% fullerene. Power conversion efficiency >6% is achieved for NT devices despite a domain size much larger than the nominal exciton diffusion length due to a favourable trade‐off in the mixed domain between exciton harvesting, charge transport, and bimolecular recombination. The miscibility of the fullerene with the NT and BT polymer is measured and correlated to the purity in devices. Importantly, polarized x‐ray scattering reveals preferential face‐on orientation of the NT polymer relative to the PCBM‐rich domains. Such ordering has previously not been observed in fullerene‐based solar cells and is shown here to be possibly a controlling or contributing factor to high performance.     

Recombination Losses Above and Below the Transport Percolation Threshold in Bulk Heterojunction Organic Solar Cells

Achieving the highest power conversion efficiencies in bulk heterojunction organic solar cells requires a morphology that delivers electron and hole percolation pathways for optimized transport, plus sufficient donor:acceptor contact area for near unity charge transfer state formation. This is a significant structural challenge, particularly in semiconducting polymer:fullerene systems. This balancing act in the model high efficiency PTB7:PC70BM blend is studied by tuning the donor:acceptor ratio, with a view to understanding the recombination loss mechanisms above and below the fullerene transport percolation threshold. The internal quantum efficiency is found to be strongly correlated to the slower carrier mobility in agreement with other recent studies. Furthermore, second‐order recombination losses dominate the shape of the current density–voltage curve in efficient blend combinations, where the fullerene phase is percolated. However, below the charge transport percolation threshold, there is an electric‐field dependence of first‐order losses, which includes electric‐field‐dependent photogeneration. In the intermediate regime, the fill factor appears to be limited by both first‐ and second‐order losses. These findings provide additional basic understanding of the interplay between the bulk heterojunction morphology and the order of recombination in organic solar cells. They also shed light on the limitations of widely used transport models below the percolation threshold.     

Inter‐Fullerene Electronic Coupling Controls the Efficiency of Photoinduced Charge Generation in Organic Bulk Heterojunctions

Photoinduced charge generation (PCG) dynamics are notoriously difficult to correlate with specific molecular properties in device relevant polymer:fullerene organic photovoltaic blend films due to the highly complex nature of the solid state blend morphology. Here, this study uses six judiciously selected trifluoromethylfullerenes blended with the prototypical polymer poly(3‐hexylthiophene) and measure the PCG dynamics in 50 fs–500 ns time scales with time‐resolved microwave conductivity and femtosecond transient absorption spectroscopy. The isomeric purity and thorough chemical characterization of the fullerenes used in this study allow for a detailed correlation between molecular properties, driving force, local intermolecular electronic coupling and, ultimately, the efficiency of PCG yield. The findings show that the molecular design of the fullerene not only determines inter‐fullerene electronic coupling, but also influences the decay dynamics of free holes in the donor phase even when the polymer microstructure remains unchanged.     

Inverted Tandem Polymer Solar Cells with Polyethylenimine‐Modified MoOX/Al2O3:ZnO Nanolaminate as the Charge Recombination Layers

A new charge recombination layer for inverted tandem polymer solar cells is reported. A bilayer of MoO_X/Al₂O₃:ZnO nanolaminate is shown to enable efficient charge recombination in inverted tandem cells. A polymer surface modification on the MoO_X/Al₂O₃:ZnO nanolaminate bilayer increases the work function contrast between the two outward surfaces of the charge recombination layer, further improving the performance of tandem solar cells. An analysis of the electrical, optical, and surface properties of the charge recombination layer is presented. Inverted tandem polymer solar cells, with two photoactive layers comprising poly (3‐hexylthiophene) (P3HT):indene‐C₆₀ bisadduct (IC₆₀BA) for the bottom cell and poly[(4,8‐bis‐(2‐ethylhexyloxy)‐benzo[1,2‐b:4,5‐b']dithiophene)‐2,6‐diyl‐alt‐(4‐(2‐ethylhexanoyl)‐thieno[3,4‐b]thiophene))‐2,6‐diyl] (PBDTTT‐C):[6,6]‐phenyl C₆₁ butyric acid methyl ester (PC₆₀BM) for the top cell, yield an open‐circuit voltage of 1481 mV ± 15 mV, a short‐circuit current density of 7.1 mA cm^?2 ± 0.1 mA cm^?2, and a fill factor of 0.62 ± 0.01, resulting in a power conversion efficiency of 6.5% ± 0.1% under simulated AM 1.5G, 100 mW cm^?2 illumination.     

Nonequilibrium Charge Dynamics in Organic Solar Cells

The dynamics of charge carriers after their creation at, or near, an interface play a critical role in determining the efficiency of organic solar cells as they dictate, via mechanisms that are not yet fully understood, the pathways for charge separation and recombination. Here, a combination of ultrafast transient spectroscopy and kinetic Monte Carlo simulations based on a minimalistic model are used to examine various aspects of these charge dynamics in a typical donor‐acceptor copolymer:methanofullerene blend. The observed rates of charge carrier energetic relaxation and recombination for a sequence of charge densities can be all consistently described in terms of the extended Gaussian disorder model. The physical picture that arises is a) that initial charge motion is highly diffusive and boosted by energetic relaxation in the disordered density of states and b) that mobile charge carriers dissociate from and re‐associate into Coulombically associated pairs faster than they recombine, especially at early times. A simple analytical calculation confirms this picture and can be used to identify sub‐Langevin recombination as the cause for quantitative deviations between the Monte Carlo calculations and the measured concentration dependence of the charge recombination.     

The Importance of Fullerene Percolation in the Mixed Regions of Polymer–Fullerene Bulk Heterojunction Solar Cells

Most optimized donor‐acceptor (D‐A) polymer bulk heterojunction (BHJ) solar cells have active layers too thin to absorb greater than ～80% of incident photons with energies above the polymer's band gap. If the thickness of these devices could be increased without sacrificing internal quantum efficiency, the device power conversion efficiency (PCE) could be significantly enhanced. We examine the device characteristics of BHJ solar cells based on poly(di(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐octylthieno[3,4‐c]pyrrole‐4,6‐dione) (PBDTTPD) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) with 7.3% PCE and find that bimolecular recombination limits the active layer thickness of these devices. Thermal annealing does not mitigate these bimolecular recombination losses and drastically decreases the PCE of PBDTTPD BHJ solar cells. We characterize the morphology of these BHJs before and after thermal annealing and determine that thermal annealing drastically reduces the concentration of PCBM in the mixed regions, which consist of PCBM dispersed in the amorphous portions of PBDTTPD. Decreasing the concentration of PCBM may reduce the number of percolating electron transport pathways within these mixed regions and create morphological electron traps that enhance charge‐carrier recombination and limit device quantum efficiency. These findings suggest that (i) the concentration of PCBM in the mixed regions of polymer BHJs must be above the PCBM percolation threshold in order to attain high solar cell internal quantum efficiency, and (ii) novel processing techniques, which improve polymer hole mobility while maintaining PCBM percolation within the mixed regions, should be developed in order to limit bimolecular recombination losses in optically thick devices and maximize the PCE of polymer BHJ solar cells.     

Ternary Organic Solar Cells with Minimum Voltage Losses

A new strategy for designing ternary solar cells is reported in this paper. A low‐bandgap polymer named PTB7‐Th and a high‐bandgap polymer named PBDTTS‐FTAZ sharing the same bulk ionization potential and interface positive integer charge transfer energy while featuring complementary absorption spectra are selected. They are used to fabricate efficient ternary solar cells, where the hole can be transported freely between the two donor polymers and collected by the electrode as in one broadband low bandgap polymer. Furthermore, the fullerene acceptor is chosen so that the energy of the positive integer charge transfer state of the two donor polymers is equal to the energy of negative integer charge transfer state of the fullerene, enabling enhanced dissociation of all polymer donor and fullerene acceptor excitons and suppressed bimolecular and trap assistant recombination. The two donor polymers feature good miscibility and energy transfer from high‐bandgap polymer of PBDTTS‐FTAZ to low‐bandgap polymer of PTB7‐Th, which contribute to enhanced performance of the ternary solar cell.     

Unifying Charge Generation,Recombination, and Extraction in Low‐Offset Non‐Fullerene Acceptor Organic Solar Cells

Even though significant breakthroughs with over 18% power conversion efficiencies (PCEs) in polymer:non‐fullerene acceptor (NFA) bulk heterojunction organic solar cells (OSCs) have been achieved, not many studies have focused on acquiring a comprehensive understanding of the underlying mechanisms governing these systems. This is because it can be challenging to delineate device photophysics in polymer:NFA blends comprehensively, and even more complicated to trace the origins of the differences in device photophysics to the subtle differences in energetics and morphology. Here, a systematic study of a series of polymer:NFA blends is conducted to unify and correlate the cumulative effects of i) voltage losses, ii) charge generation efficiencies, iii) non‐geminate recombination and extraction dynamics, and iv) nuanced morphological differences with device performances. Most importantly, a deconvolution of the major loss processes in polymer:NFA blends and their connections to the complex BHJ morphology and energetics are established. An extension to advanced morphological techniques, such as solid‐state NMR (for atomic level insights on the local ordering and donor:acceptor π? π interactions) and resonant soft X‐ray scattering (for donor and acceptor interfacial area and domain spacings), provide detailed insights on how efficient charge generation, transport, and extraction processes can outweigh increased voltage losses to yield high PCEs.