Open‐Circuit Voltage in Organic Solar Cells: The Impacts of Donor Semicrystallinity and Coexistence of Multiple Interfacial Charge‐Transfer Bands

In organic solar cells (OSCs), the energy of the charge‐transfer (CT) complexes at the donor–acceptor interface, E _CT, determines the maximum open‐circuit voltage (V _OC). The coexistence of phases with different degrees of order in the donor or the acceptor, as in blends of semi‐crystalline donors and fullerenes in bulk heterojunction layers, influences the distribution of CT states and the V _OC enormously. Yet, the question of how structural heterogeneities alter CT states and the V _OC is seldom addressed systematically. In this work, we combine experimental measurements of vacuum‐deposited rubrene/C₆₀ bilayer OSCs, with varying microstructure and texture, with density functional theory calculations to determine how relative molecular orientations and extents of structural order influence E _CT and V _OC. We find that varying the microstructure of rubrene gives rise to CT bands with varying energies. The CT band that originates from crystalline rubrene lies up to ≈0.4 eV lower in energy compared to the one that arises from amorphous rubrene. These low‐lying CT states contribute strongly to V _OC losses and result mainly from hole delocalization in aggregated rubrene. This work points to the importance of realizing interfacial structural control that prevents the formation of low E _CT configurations and maximizes V _OC.     

Understanding Open‐Circuit Voltage Loss through the Density of States in Organic Bulk Heterojunction Solar Cells

The field of organic photovoltaics has recently produced highly efficient single‐junction cells with power conversion efficiency >10%, yet the open‐circuit voltage (V_OC) remains relatively low in many high performing systems. An accurate picture of the density of states (DOS) in working solar cells is crucial to understanding the sources of voltage loss, but remains difficult to obtain experimentally. Here, the tail of the DOS is characterized in a number of small molecule bulk heterojunction solar cells from the charge density dependence of V_OC, and is directly compared to the disorder present within donor and acceptor components as measured by Kelvin probe. Using these DOS distributions, the total energy loss relative to the charge transfer state energy (E_CT)—ranging from ≈0.5 to 0.7 eV—is divided into contributions from energetic disorder and from charge recombination, and the extent to which these factors limit the V_OC is assessed.     

On the Impact of Contact Selectivity and Charge Transport on the Open‐Circuit Voltage of Organic Solar Cells

The selectivity of electrodes of solar cells is a critical factor that can limit the overall efficiency. If the selectivity of an electrode is not sufficient both electrons and holes recombine at its surface. In materials with poor transport properties such as in organic solar cells, these surface recombination currents are accompanied by large gradients of the quasi‐Fermi energies as the driving force. Experimental results from current–voltage characteristics, advanced photo‐ and electroluminescence as well as charge extraction of three different photoactive materials are shown and compared to drift‐diffusion simulations. It can be concluded that in cases of electrodes with reduced selectivity the decrease of the open‐circuit voltage can be divided into two distinct contributions, the reduction of the overall steady‐state charge carrier density and the gradients of the quasi‐Fermi energies. The results clearly show that for photoactive layers with poor transport properties, the gradient of the quasi‐Fermi energy in the vicinity of the contact is the main contribution to the loss in open‐circuit voltage. For imbalanced mobilities, this gives rise to the phenomenon that it is more challenging to realize a selective contact for the less mobile charge carrier, i.e., the hole contact in most organic solar cells.     

Molecular Understanding of the Open‐Circuit Voltage of Polymer:Fullerene Solar Cells

The origin of open‐circuit voltage (V_OC) was studied for polymer solar cells based on a blend of poly(3‐hexylthiophene) (P3HT) and seven fullerene derivatives with different LUMO energy levels and side chains. The temperature dependence of J–V characteristics was analyzed by an equivalent circuit model. As a result, V_OC increased with the decrease in the saturation current density J₀ of the device. Furthermore, J₀ was dependent on the activation energy E_A for J₀, which is related to the HOMO–LUMO energy gap between P3HT and fullerene. Interestingly, the pre‐exponential term J₀₀ for J₀ was larger for pristine fullerenes than for substituted fullerene derivatives, suggesting that the electronic coupling between molecules also has substantial impact on V_OC. This is probably because the recombination is non‐diffusion‐lmilited reaction depending on electron transfer at the P3HT/fullerene interface. In summary, the origin of V_OC is ascribed not only to the relative HOMO–LUMO energy gap but also to the electronic couplings between fullerene/fullerene and polymer/fullerene.     

Perovskite Solar Cells on the Way to Their Radiative Efficiency Limit – Insights Into a Success Story of High Open‐Circuit Voltage and Low Recombination

Inorganic‐organic lead‐halide perovskite solar cells have reached efficiencies above 22% within a few years of research. Achieved photovoltages of >1.2 V are outstanding for a material with a bandgap of 1.6 eV – in particular considering that it is solution processed. Such values demand for low non‐radiative recombination rates and come along with high luminescence yields when the solar cell is operated as a light emitting diode. This progress report summarizes the developments on material composition and device architecture, which allowed for such high photovoltages. It critically assesses the term “lifetime”, the theories and experiments behind it, and the different recombination mechanisms present. It attempts to condense reported explanations for the extraordinary optoelectronic properties of the material. Amongst those are an outstanding defect tolerance due to antibonding valence states and the capability of bandgap tuning, which might make the dream of low‐cost highly efficient solution‐processed thin film solar cells come true. Beyond that, the presence of photon recycling will open new opportunities for photonic device design.     

Recombination in Polymer:Fullerene Solar Cells with Open‐Circuit Voltages Approaching and Exceeding 1.0 V

Polymer:fullerene solar cells are demonstrated with power conversion efficiencies over 7% with blends of PBDTTPD and PC₆₁BM. These devices achieve open‐circuit voltages (V_oc) of 0.945 V and internal quantum efficiencies of 88%, making them an ideal candidate for the large bandgap junction in tandem solar cells. V_oc’s above 1.0 V are obtained when the polymer is blended with multiadduct fullerenes; however, the photocurrent and fill factor are greatly reduced. In PBDTTPD blends with multiadduct fullerene ICBA, fullerene emission is observed in the photoluminescence and electroluminescence spectra, indicating that excitons are recombining on ICBA. Voltage‐dependent, steady state and time‐resolved photoluminescence measurements indicate that energy transfer occurs from PBDTTPD to ICBA and that back hole transfer from ICBA to PBDTTPD is inefficient. By analyzing the absorption and emission spectra from fullerene and charge transfer excitons, we estimate a driving free energy of –0.14 ± 0.06 eV is required for efficient hole transfer. These results suggest that the driving force for hole transfer may be too small for efficient current generation in polymer:fullerene solar cells with V_oc values above 1.0 V and that non‐fullerene acceptor materials with large optical gaps (>1.7 eV) may be required to achieve both near unity internal quantum efficiencies and values of V_oc exceeding 1.0 V.     

A New Terthiophene‐Thienopyrrolodione Copolymer‐Based Bulk Heterojunction Solar Cell with High Open‐Circuit Voltage

A new semiconducting polymer based on terthiophene‐thienopyrrolodione alternating building blocks with a deep HOMO energy level (5.66 eV) is presented. The polymer is prepared by a direct heteroarylation polycondensation reaction, which is a low‐cost and green alternative to the standard Stille coupling reaction and thus avoids any use of toxic stannyl derivatives. Integrating the polymer into bulk heterojunction solar cells with [6,6]‐phenyl C71‐butyric acid methyl ester ([70]PCBM) leads to a PCE of over 6% and a high open‐circuit voltage of up to 0.94 V. To obtain these results a unique processing additive, 1‐chloronaphthalene, is used, and a relatively low concentration of [70]PCBM is used in the blend solution.     

Efficient Organic Solar Cells with Extremely High Open‐Circuit Voltages and Low Voltage Losses by Suppressing Nonradiative Recombination Losses

One of the most important factors that limits the efficiencies of bulk‐heterojunction organic solar cells (OSCs) is the modest open‐circuit voltage (V_oc) due to their large voltage loss (V_loss) caused by significant nonradiative recombination loss. To boost the performance of OSCs toward their theoretical limit, developing high‐performance donor: acceptor systems featuring low V_loss with suppressed nonradiative recombination losses (<0.30 V) is desired. Herein, high performance OSCs based on a polymer donor benzodithiophene‐difluorobenzoxadiazole‐2‐decyltetradecyl (BDT‐ffBX‐DT) and perylenediimide‐based acceptors (PDI dimer with spirofluorene linker (SFPDI), PDI4, and PDI6) are reported which offer a high power conversion efficiency (PCE) of 7.5%, 56% external quantum efficiency associated with very high V_oc (>1.10 V) and low V_loss (<0.60 V). A high V_oc up to 1.23 V is achieved, which is among the highest values reported for OSCs with a PCE beyond 6%, to date. These attractive results are benefit from the suppressed nonradiative recombination voltage loss, which is as low as 0.20 V. This value is the lowest value for OSCs so far and is comparable to high performance crystalline silicon and perovskite solar cells. These results show that OSCs have the potential to achieve comparable V_oc and voltage loss as inorganic photovoltaic technologies.     

Organic Salts as a Route to Energy Level Control in Low Bandgap,High Open‐Circuit Voltage Organic and Transparent Solar Cells that Approach the Excitonic Voltage Limit

A new series of organic salts with selective near‐infrared (NIR) harvesting to 950 nm is reported, and anion selection and blending is demonstrated to allow for fine tuning of the open‐circuit voltage. Extending photoresponse deeper into the NIR is a significant challenge facing small molecule organic photovoltaics, and recent demonstrations have been limited by open‐circuit voltages much lower than the theoretical and practical limits. This work presents molecular design strategies that enable facile tuning of energy level alignment and open‐circuit voltages in organic salt‐based photovoltaics. Anions are also shown to have a strong influence on exciton diffusion length. These insights provide a clear route toward achieving high efficiency transparent and panchromatic photovoltaics, and open up design opportunities to rapidly tailor molecules for new donor–acceptor systems.     

Relating Frontier Orbital Energies from Voltammetry and Photoelectron Spectroscopy to the Open‐Circuit Voltage of Organic Solar Cells

For 19 diketopyrrolopyrrole polymers, the highest occupied molecular orbital (HOMO) energies are determined from i) the oxidation potential with square‐wave voltammetry (SWV), ii) the ionization potential using ultraviolet photoelectron spectroscopy (UPS), and iii) density functional theory (DFT) calculations. The SWV HOMO energies show an excellent linear correlation with the open‐circuit voltage (V_oc) of optimized solar cells in which the polymers form blends with a fullerene acceptor ([6,6]‐phenyl‐C₆₁‐butyl acid methyl ester or [6,6]‐phenyl‐C₇₁‐butyl acid methyl ester). Remarkably, the slope of the best linear fit is 0.75 ± 0.04, i.e., significantly less than unity. A weaker correlation with V_oc is found for the HOMO energies obtained from UPS and DFT. Within the experimental error, the SWV and UPS data are correlated with a slope close to unity. The results show that electrochemically determined oxidation potentials provide an excellent method for predicting the V_oc of bulk heterojunction solar cells, with absolute deviations less than 0.1 V.     

Beyond Langevin Recombination: How Equilibrium Between Free Carriers and Charge Transfer States Determines the Open‐Circuit Voltage of Organic Solar Cells

Organic solar cells lag behind their inorganic counterparts in efficiency due largely to low open‐circuit voltages (V_oc). In this work, a comprehensive framework for understanding and improving the open‐circuit voltage of organic solar cells is developed based on equilibrium between charge transfer (CT) states and free carriers. It is first shown that the ubiquitous reduced Langevin recombination observed in organic solar cells implies equilibrium and then statistical mechanics is used to calculate the CT state population density at each voltage. This general result permits the quantitative assignment of V_oc losses to a combination of interfacial energetic disorder, non‐negligible CT state binding energies, large degrees of mixing, and sub‐ns recombination at the donor/acceptor interface. To quantify the impact of energetic disorder, a new temperature‐dependent CT state absorption measurement is developed. By analyzing how the apparent CT energy varies with temperature, the interfacial disorder can be directly extracted. 63–104 meV of disorder is found in five systems, contributing 75–210 mV of V_oc loss. This work provides an intuitive explanation for why qV_oc is almost always 500–700 meV below the energy of the CT state and shows how the voltage can be improved.     

Exploring the Limiting Open‐Circuit Voltage and the Voltage Loss Mechanism in Planar CH3NH3PbBr3 Perovskite Solar Cells

Perovskite solar cells based on CH₃NH₃PbBr₃ with a band gap of 2.3 eV are attracting intense research interests due to their high open‐circuit voltage (V_oc) potential, which is specifically relevant for the use in tandem configuration or spectral splitting. Many efforts have been performed to optimize the V_oc of CH₃NH₃PbBr₃ solar cells; however, the limiting V_oc (namely, radiative V_oc:V_oc,rad) and the corresponding ΔV_oc (the difference between V_oc,rad and V_oc) mechanism are still unknown. Here, the average V_oc of 1.50 V with the maximum value of 1.53 V at room temperature is achieved for a CH₃NH₃PbBr₃ solar cell. External quantum efficiency measurements with electroluminescence spectroscopy determine the V_oc,rad of CH₃NH₃PbBr₃ cells with 1.95 V and a ΔV_oc of 0.45 V at 295 K. When the temperature declines from 295 to 200 K, the obtained V_oc remains comparably stable in the vicinity of 1.5 V while the corresponding ΔV_oc values show a more significant increase. Our findings suggest that the V_oc of CH₃NH₃PbBr₃ cells is primarily limited by the interface losses induced by the charge extraction layer rather than by bulk dominated recombination losses. These findings are important for developing strategies how to further enhance the V_oc of CH₃NH₃PbBr₃‐based solar cells.     

Achieving High Open‐Circuit Voltages up to 1.57 V in Hole‐Transport‐Material‐Free MAPbBr3 Solar Cells with Carbon Electrodes

An open‐circuit voltage (V_oc) of 1.57 V under simulated AM1.5 sunlight in planar MAPbBr₃ solar cells with carbon (graphite) electrodes is obtained. The hole‐transport‐material‐free MAPbBr₃ solar cells with the normal architecture (FTO/TiO₂/MAPbBr₃/carbon) show little hysteresis during current–voltage sweep under simulated AM1.5 sunlight. A solar‐to‐electricity power conversion efficiency of 8.70% is achieved with the champion device. Accordingly, it is proposed that the carbon electrodes are effective to extract photogenerated holes in MAPbBr₃ solar cells, and the industry‐applicable carbon electrodes will not limit the performance of bromide‐based perovskite solar cells. Based on the analysis of the band alignment, it is found that the voltage (energy) loss across the interface between MAPbBr₃ and carbon is very small compared to the offset between the valence band maximum of MAPbBr₃ and the work function of graphite. This finding implies either Fermi level pinning or highly doped region inside MAPbBr₃ layer exists. The band‐edge electroluminescence spectra of MAPbBr₃ from the solar cells further support no back‐transfer pathways of electrons across the MAPbBr₃/TiO₂ interface.     

Oxygenated CdS Buffer Layers Enabling High Open‐Circuit Voltages in Earth‐Abundant Cu2BaSnS4 Thin‐Film Solar Cells

Earth‐abundant Cu₂BaSnS₄ (CBTS) thin films exhibit a wide bandgap of 2.04–2.07 eV, a high absorption coefficient > 10⁴ cm^?1, and a p‐type conductivity, suitable as a top‐cell absorber in tandem solar cell devices. In this work, sputtered oxygenated CdS (CdS:O) buffer layers are demonstrated to create a good p–n diode with CBTS and enable high open‐circuit voltages of 0.9–1.1 V by minimizing interface recombination. The best power conversion efficiency of 2.03% is reached under AM 1.5G illumination based on the configuration of fluorine‐doped SnO₂ (back contact)/CBTS/CdS:O/CdS/ZnO/aluminum‐doped ZnO (front contact).     

Disorder‐Induced Open‐Circuit Voltage Losses in Organic Solar Cells During Photoinduced Burn‐In

The photoinduced open‐circuit voltage (V_oc) loss commonly observed in bulk heterojunction organic solar cells made from amorphous polymers is investigated. It is observed that the total charge carrier density and, importantly, the recombination dynamics are unchanged by photoinduced burn‐in. Charge extraction is used to monitor changes in the density of states (DOS) during degradation of the solar cells, and a broadening over time is observed. It is proposed that the V_oc losses observed during burn‐in are caused by a redistribution of charge carriers in a broader DOS. The temperature and light intensity dependence of the V_oc losses can be described with an analytical model that contains the amount of disorder broadening in a Gaussian DOS as the only fit parameter. Finally, the V_oc loss in solar cells made from amorphous and crystalline polymers is compared and an increased stability observed in crystalline polymer solar cells is investigated. It is found that solar cells made from crystalline materials have a considerably higher charge carrier density than those with amorphous materials. The effects of a DOS broadening upon aging are suppressed in solar cells with crystalline materials due to their higher carrier density, making crystalline materials more stable against V_oc losses during burn‐in.     

Ultra‐High Voltage Multijunction Organic Solar Cells for Low‐Power Electronic Applications

Low power electronics are an ideal application for organic photovoltaics (OPV) where a low‐cost OPV device can be integrated directly with a battery to provide a constant power source. We demonstrate ultra‐high voltage small molecule multijunction devices with open circuit voltage (V_OC) values of up to 7V. Optical modelling is employed to aid the optimisation of the complex multi‐layer stacks and ensure current balancing is achieved between sub‐cells, and optimised multijunction devices show power conversion efficiencies of up to 3.4% which is a modest increase over the single junction devices. Sub‐cell donor/acceptor pairs of boron subphthalocyanine chloride (SubPc)/fullerene (C₆₀) and SubPc/Cl₆‐SubPc were selected both for their high V_OC in order to minimise the required number of junctions, but also for their absorption overlap to reduce the spectral dependence of the device performance. As a result, the devices are shown to directly charge a micro‐energy cell type battery under both low illumination intensity white light and monochromatic illumination.