Comparison of different pretreatment methods for lignocellulosic materials. Part II: Influence of pretreatment on the properties of rye straw lignin

Several processes have been suggested to convert various types of lignocellulosic biomass into lignin products and saccharides. This paper evaluates the suitability of an organosolv process, a process using soda, a hydrothermal process and a process developed in this work, called the “Aquasolve process” for inclusion into a lignocellulosic biorefinery concept. Part II of this paper investigates the influence of the different pretreatment processes on the properties of rye straw lignin and evaluates their ability to produce high recoveries of high quality lignin.Specifications for high quality lignin products are defined and the isolated lignin fractions are analysed by Klason lignin, carbohydrate and ash content, elemental analysis, thermo-gravimetric analysis, ³¹P NMR, and size exclusion chromatography. The organosolv process shows the largest lignin recovery, followed by the soda and Aquasolve processes. Lignin products from the soda process, the Aquasolve process and with reservation the organosolv process show interesting properties for polymer applications.     

Combined rapid-steam hydrolysis and organosolv pretreatment of mixed southern hardwoods

Various types of pretreatments are used for biomass conversion of woods. The major objective of most pre treatments is to increase the susceptibility of cellulose and lignocellulose material to acid and enzymatic hydrolysis. In this study, southern mixed hardwoods were pretreated by combined rapid steam hydrolysis (RASH) and organosolv methods. It was found that the major factor in the pretreatment was the RASH temperatures. The organosolv temperature had only a minor effect on the reactivity of the final product. The enzymatic rate studies indicated that the RASH process helps in increasing the accessibility of cellulose to enzymatic hydrolysis and increased the amount of soluble lignin While the organosolv process only removed solubilized lignin. Another effect of the combined treatment was the decreasing of the enzymatic rate relative to a single RASH pretreatment. All hemicellulose is lost during these pretreatments. Three alcohols (methanol, ethanol, and butanol) were studied using a combined RASH organosolv process. At lower temperatures there were small differences between the alcohols; however, at higher temperatures all alcohols were equally effective. At longer RASH times, the percentage of glucose in the final product, as well as the amount of solubilized lignin, increased. However, the longer RASH times led to a decrease in enzymatic rates, Organosolv residence time studies of 15, 30, and 45 minutes displayed little effect on the product. Various wood-to-solvent ratios and water-to-alcohol ratios had very little effect on the yield of products. The stability of RASH treated material be fore organosolv process was studied under various storage conditions. The storage conditions had no apparent effect on the product.     

Biorefining of softwoods using ethanol organosolv pulping: preliminary evaluation of process streams for manufacture of fuel-grade ethanol and co-products

Pulps with residual lignin ranging from 6.4-27.4% (w/w) were prepared from mixed softwoods using a proprietary biorefining technology (the Lignol process) based on aqueous ethanol organosolv extraction. The pulps were evaluated for bioconversion using enzymatic hydrolysis of the cellulose fraction to glucose and subsequent fermentation to ethanol. All pulps were readily hydrolyzed without further delignification. More than 90% of the cellulose in low lignin pulps (< or =18.4% residual lignin) was hydrolyzed to glucose in 48 h using an enzyme loading of 20 filter paper units/g cellulose. Cellulose in a high lignin pulp (27.4% residual lignin) was hydrolyzed to >90% conversion within 48 h using 40 filter paper units/g. The pulps performed well in both sequential and simultaneous saccharification and fermentation trials indicating an absence of metabolic inhibitors. Chemical and physical analyses showed that lignin extracted during organosolv pulping of softwood is a suitable feedstock for production of lignin-based adhesives and other products due to its high purity, low molecular weight, and abundance of reactive groups. Additional co-products may be derived from the hemicellulose sugars and furfural recovered from the water-soluble stream.     

Inhibition of cellulase, xylanase and beta-glucosidase activities by softwood lignin preparations

The conversion of lignocellulosic biomass to fuel ethanol typically involves a disruptive pretreatment process followed by enzyme-catalyzed hydrolysis of the cellulose and hemicellulose components to fermentable sugars. Attempts to improve process economics include protein engineering of cellulases, xylanases and related hydrolases to improve their specific activity or stability. However, it is recognized that enzyme performance is reduced during lignocellulose hydrolysis by interaction with lignin or lignin-carbohydrate complex (LCC), so the selection or engineering of enzymes with reduced lignin interaction offers an alternative means of enzyme improvement. This study examines the inhibition of seven cellulase preparations, three xylanase preparations and a beta-glucosidase preparation by two purified, particulate lignin preparations derived from softwood using an organosolv pretreatment process followed by enzymatic hydrolysis. The two lignin preparations had similar particle sizes and surface areas but differed significantly in other physical properties and in their chemical compositions determined by a 2D correlation HSQC NMR technique and quantitative 13C NMR spectroscopy. The various cellulases differed by up to 3.5-fold in their inhibition by lignin, while the xylanases showed less variability (< or = 1.7-fold). Of all the enzymes tested, beta-glucosidase was least affected by lignin.     

Liquid hot water and alkaline pretreatment of soybean straw for improving cellulose digestibility

Soybean straw was pretreated with either liquid hot water (LHW) (170-210 °C for 3-10 min) or alkaline soaking (4-40 g NaOH/100 g dry straw) at room temperature to evaluate the effects on cellulose digestibility. Nearly 100% cellulose was recovered in pretreated solids for both pretreatment methods. For LHW pretreatment, xylan dissolution from the raw material increased with pretreatment temperature and time. Cellulose digestibility was correlated with xylan dissolution. A maximal glucose yield of 70.76%, corresponding to 80% xylan removal, was obtained with soybean straw pretreated at 210 °C for 10 min. NaOH soaking at ambient conditions removed xylan up to 46.37% and the subsequent glucose yield of pretreated solids reached up to 64.55%. Our results indicated LHW pretreatment was more effective than NaOH soaking for improving cellulose digestibility of soybean straw.     

Mild alkaline pretreatment can achieve high hydrolytic and fermentation efficiencies for rice straw conversion to bioethanol

Abstract

Mild alkaline pretreatment was evaluated as a strategy for effective lignin removal and hydrolysis of rice straw. The pretreatment efficiency of different NaOH concentrations (0.5, 1.0, 1.5 or 2.0% w/w) was assessed. Rice straw (RS) pretreated with 1.5% NaOH achieved better sugar yield compared to other concentrations used. A cellulose conversion efficiency of 91% (45.84?mg/ml glucose release) was attained from 1.5% NaOH pretreated rice straw (PRS), whereas 1% NaOH pretreated rice straw yielded 35.10?mg/ml of glucose corresponding to a cellulose conversion efficiency of 73.81%. The ethanol production from 1% and 1.5% NaOH pretreated RS hydrolysates was similar at ～3.3% (w/v), corresponding to a fermentation efficiency of 86%. The non-detoxified hydrolysate was fermented using the novel yeast strain Saccharomyces cerevisiae RPP-03O without any additional supplementation of nutrients.     

The bioconversion of mountain pine beetle-killed lodgepole pine to fuel ethanol using the organosolv process

Lodgepole pine (Pinus contorta) killed by mountain pine beetle (Dendroctonus ponderosae) (BLP) was compared with healthy lodgepole pine (HLP) for bioconversion to ethanol and high-value co-products. The BLP and HLP chips were pretreated using an ethanol organosolv process at a variety of severities. It was shown that the BLP was easier to pretreat and delignify than were the HLP chips. The resulting pretreated BLP substrate had a lower residual lignin, lower degree of polymerization of cellulose, lower cellulose crystallinity, smaller fiber size and thereby a better enzymatic hydrolysability than did the HLP substrates. However, under the same conditions, the BLP showed lower substrate yield and cellulose recovery than did the HLP, which likely resulted from the excessive hydrolysis and subsequent decomposition of the cellulose and hemicellulose during the pretreatment. The BLP wood yielded more ethanol organosolv lignin than was obtained with the HLP material. The HLP lignin had a lower molecular weight and narrower distribution than did the BLP lignin. It appears that the beetle killed LP is more receptive to organosolv pretreatment other than a slightly lower recovery of carbohydrates.     

Ionic liquid‐mediated selective extraction of lignin from wood leading to enhanced enzymatic cellulose hydrolysis

Lignocellulose represents a key sustainable source of biomass for transformation into biofuels and bio‐based products. Unfortunately, lignocellulosic biomass is highly recalcitrant to biotransformation, both microbial and enzymatic, which limits its use and prevents economically viable conversion into value‐added products. As a result, effective pretreatment strategies are necessary, which invariably involves high energy processing or results in the degradation of key components of lignocellulose. In this work, the ionic liquid, 1‐ethyl‐3‐methylimidazolium acetate ([Emim][CH₃COO]), was used as a pretreatment solvent to extract lignin from wood flour. The cellulose in the pretreated wood flour becomes far less crystalline without undergoing solubilization. When 40% of the lignin was removed, the cellulose crystallinity index dropped below 45, resulting in >90% of the cellulose in wood flour to be hydrolyzed by Trichoderma viride cellulase. [Emim] [CH₃COO] was easily reused, thereby resulting in a highly concentrated solution of chemically unmodified lignin, which may serve as a valuable source of a polyaromatic material as a value‐added product. Biotechnol. Bioeng. 2009;102: 1368–1376. © 2008 Wiley Periodicals, Inc.     

Effect of ozonolysis pretreatment on enzymatic digestibility of wheat and rye straw

Wheat and rye straws were pretreated with ozone to increase the enzymatic hydrolysis extent of potentially fermentable sugars. Through a 2(5-1) factorial design, this work studies the influence of five operating parameters (moisture content, particle size, ozone concentration, type of biomass and air/ozone flow rate) on ozonization pretreatment of straw in a fixed bed reactor under room conditions. The acid insoluble lignin content of the biomass was reduced in all experiments involving hemicellulose degradation. Near negligible losses of cellulose were observed. Enzymatic hydrolysis yields of up to 88.6% and 57% were obtained compared to 29% and 16% in non-ozonated wheat and rye straw respectively. Moisture content and type of biomass showed the most significant effects on ozonolysis. Additionally, ozonolysis experiments in basic medium with sodium hydroxide evidenced a reduction in solubilization and/or degradation of lignin and reliable cellulose and hemicellulose degradation.     

Fractionation of wheat straw by atmospheric acetic acid process

Fractionation of wheat straw was investigated using an atmospheric acetic acid process. Under the typical conditions of 90% (v/v) aqueous AcOH, 4% H(2)SO(4) (w/w, on straw), ratio of liquor to straw (L/S) 10 (v/w), pulping temperature 105 degrees C, and pulping time 3h, wheat straw was fractionated to pulp (cellulose), lignin and monosaccharides mainly from hemicellulose with yields of approximately 50%, 15% and 35%, respectively. Acetic acid pulp from the straw had an acceptable strength for paper and could be bleached to a high brightness over 85% with a short bleaching sequence. Acetic acid pulp was also a potential feedstock for fuels and chemicals. The acetic acid process separated pentose and hexose in wheat straw to a large extent. Most of the pentose (xylan) was dissolved, whereas the hexose (glucan) remained in the pulp. Approximately 30% of carbohydrates in wheat straw were hydrolyzed to monosaccharides during acetic acid pulping, of which xylose accounted for 70% and glucose for 12%. The acetic acid lignin from wheat straw showed relatively lower molecular weight and fusibility, which made the lignin a promising raw material for many products, such as adhesive and molded products.     

Eucalyptus globulus wood fractionation by autohydrolysis and organosolv delignification

This work provides an assessment on the fractionation of Eucalyptus globulus wood by sequential stages of autohydrolysis (to cause the solubilization of hemicelluloses) and organosolv pulping (to dissolve lignin, leaving solids enriched in cellulose). With this approach, valuable products (hemicellulose-derived saccharides, sulphur-free lignin fragments and cellulosic substrates with low contents of residual hemicelluloses) are obtained in separate streams, according to the biomass refinery approach. Autohydrolysis was carried out under optimized operational conditions, and organosolv pulping was performed using uncatalyzed ethanol-water solutions. The effects of the most influential operational variables (autohydrolysis severity, delignification temperature and ethanol concentration in the organosolv stage) on solid yield, solid composition, cellulose susceptibility and recovery of the various fractions was assessed using statistical methods, which enabled the identification of the most favourable operational conditions.     

Effects of organosolv pretreatment and enzymatic hydrolysis on cellulose structure and crystallinity in Loblolly pine

Ethanol organosolv pretreatment was performed on Loblolly pine to enhance the efficiency of enzymatic hydrolysis of cellulose to glucose. Solid-state ¹³C NMR spectroscopy coupled with line shape analysis was used to determine the structure and crystallinity of cellulose isolated from pretreated and enzyme-hydrolyzed Loblolly pine. The results indicate reduced crystallinity of the cellulose following the organosolv pretreatment, which renders the substrate easily hydrolyzable by cellulase. The degree of crystallinity increases and the relative proportion of para-crystalline and amorphous cellulose decreases after enzymatic hydrolysis, indicating preferential hydrolysis of these regions by cellulase. The structural and compositional changes in this material resulting from the organosolv pretreatment and cellulase enzyme hydrolysis of the pretreated wood were studied with solid-state CP/MAS ¹³C NMR spectroscopy. NMR spectra of the solid material before and after the treatments show that hemicelluloses and lignin are degraded during the organosolv pretreatment.     

The Influence of Hemicellulose and Lignin Removal on the Enzymatic Digestibility from Sugarcane Bagasse

Sugarcane bagasse (SCB) was pretreated with liquid hot water (LHW) and aqueous ammonia (AA), with the objective of investigating the influence of hemicellulose and lignin removal on the enzymatic digestibility and sugar recovery. The experimental results show that LHW and aqueous ammonia have a good performance in terms of hemicellulose dissolution and lignin removal respectively. The biggest xylan recovery of 74.3 % was obtained for LHW pretreatment at 160 °C, 5 %?w/v for 20 min with the xylan dissolution of 83.1 %. And the biggest lignin removal of 84.0 % was obtained for aqueous ammonia pretreatment at 160 °C, 10 %?w/v for 60 min. Moreover, the aperture and surface area of the sample were enlarged by the liquid hot water, which improves the accessibility of the substrate to the enzyme. The lignin removal caused by aqueous ammonia pretreatment can reduce the absorption of enzyme. In addition, the correlation between the compositional change and the enzymatic digestibility indicates that the removal of hemicellulose was more effective than lignin for destruction of the hemicellulose–lignin–cellulose structure.     

Enzymatic digestion of liquid hot water pretreated hybrid poplar

Liquid hot (LHW) water pretreatment (LHW) of lignocellulosic material enhances enzymatic conversion of cellulose to glucose by solubilizing hemicellulose fraction of the biomass, while leaving the cellulose more reactive and accessible to cellulase enzymes. Within the range of pretreatment conditions tested in this study, the optimized LHW pretreatment conditions for a 15% (wt/vol) slurry of hybrid poplar were found to be 200^oC, 10 min, which resulted in the highest fermentable sugar yield with minimal formation of sugar decomposition products during the pretreatment. The LHW pretreatment solubilized 62% of hemicellulose as soluble oligomers. Hot‐washing of the pretreated poplar slurry increased the efficiency of hydrolysis by doubling the yield of glucose for a given enzyme dose. The 15% (wt/vol) slurry of hybrid poplar, pretreated at the optimal conditions and hot‐washed, resulted in 54% glucose yield by 15 FPU cellulase per gram glucan after 120 h. The hydrolysate contained 56 g/L glucose and 12 g/L xylose. The effect of cellulase loading on the enzymatic digestibility of the pretreated poplar is also reported. Total monomeric sugar yield (glucose and xylose) reached 67% after 72 h of hydrolysis when 40 FPU cellulase per gram glucan were used. An overall mass balance of the poplar‐to‐ethanol process was established based on the experimentally determined composition and hydrolysis efficiencies of the liquid hot water pretreated poplar. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

The effect of isolated lignins,obtained from a range of pretreated lignocellulosic substrates,on enzymatic hydrolysis

The influence of the residual lignin remaining in the cellulosic rich component of pretreated lignocellulosic substrates on subsequent enzymatic hydrolysis was assessed. Twelve lignin preparations were isolated by two isolation methods (protease treated lignin (PTL) and cellulolytic enzymatic lignin (CEL)) from three types of biomass (corn stover, poplar, and lodgepole pine) that had been pretreated by two processes (steam and organosolv pretreatments). Comparative analysis of the isolated lignin showed that the CEL contained lower amounts of carbohydrates and protein than did the PTL and that the isolated lignin from corn stover contained more carbohydrates than did the lignin derived from the poplar and lodgepole pine. The lower yields of acid insoluble lignin (AIL) obtained from the corn stover when using the PTL method indicated that the lignin from the corn stover had a higher hydrophilicity than did the lignin from the poplar and lodgepole pine. The isolated lignin preparations were added to the reaction mixture containing crystalline cellulose (Avicel) and their possible effects on enzymatic hydrolysis were assessed. It was apparent that the lignin isolated from lodgepole pine and steam pretreated poplar decreased the hydrolysis yields of Avicel, whereas the other isolated lignins did not appear to decrease the hydrolysis yields significantly. The hydrolysis yields of the pretreated lignocellulose and those of Avicel containing the PTL showed good correlation, indicating that the nature of the residual lignin obtained after pretreatment significantly influenced hydrolysis. Biotechnol. Bioeng. 2010;105: 871–879. © 2009 Wiley Periodicals, Inc.     

A rapid microassay to evaluate enzymatic hydrolysis of lignocellulosic substrates

Current attempts to produce ethanol from lignocellulosic biomass are focused on the optimization of pretreatment to reduce substrate recalcitrance and the improvement of enzymes for hydrolysis of the cellulose and hemicellulose components to produce fermentable sugars. Research aimed at optimizing both aspects of the bioconversion process involves assessment of the effects of multiple variables on enzyme efficiency, resulting in large factorial experiments with intensive assay requirements. A rapid assay for lignocellulose hydrolysis has been developed to address this need. Pretreated lignocellulose is formed into handsheets, which are then used to prepare small disks that are easily dispensed into microtiter plates. The hydrolysis of cellulose to glucose is estimated using an enzyme-coupled spectrophotometric assay. Using disks prepared from ethanol organosolv pretreated yellow poplar, it is shown that the assay generates data comparable with those produced by hydrolysis of pretreated yellow poplar pulp in Erlenmeyer flasks, followed by HPLC analysis of glucose. The assay shows considerable time and cost benefits over the standard assay protocol and is applicable to a broad range of lignocellulosic substrates.     

Effect of organosolv and soda pulping processes on the metals content of non-woody pulps

In this work the effect of different pulping processes (ethyleneglycol, diethyleneglycol, ethanolamine and soda) of tow abounded raw materials (empty fruit bunches - EFB and rice straw) on the ash, silicates and metals (Fe, Zn, Cu, Pb, Mn, Ni and Cd) content of the obtained pulps have been studied. Results showed that pulps obtained by diethyleneglycol pulping process presented lower metals content (756 microg/g and 501 microg/g for EFB and rice straw pulp, respectively) than soda pulps (984 microg/g and 889 microg/g). Ethanolamine pulps presented values of holocellulose (74% and 77% for EFB and rice straw pulp, respectively), alpha-cellulose (74% and 69%), kappa number (18.7 and 18.5) and viscosity (612 and 90 6ml/g) similar to those of soda pulp, and lower lignin contents (11% and 12%).     

乙醇预处理麦秆的酶解性能研究简

采用H2 SO4催化和自催化乙醇法对麦秆进行预处理,比较预处理后麦秆的主要化学组成、纤维素酶解性能和半同步糖化发酵生产乙醇特性,并进行物料衡算。结果表明：H2 SO4催化和自催化乙醇预处理过程中纤维素固体回收率大于90％。添加非离子表面活性剂吐温20和吐温80没有显著提高H2 SO4催化乙醇预处理后纤维素的酶解葡萄糖得率及半同步糖化发酵过程中乙醇的产量,而对自催化乙醇处理后麦秆的酶解和半同步糖化发酵过程有一定程度的促进作用,相应的酶解葡聚糖转化率由72.7％提高到85.0％,而半同步糖化发酵过程中乙醇质量浓度提高了11.4％。物料衡算结果表明：酸催化和自催化乙醇预处理后葡聚糖回收率分别为91.0％和95.4％;半同步糖化发酵生产乙醇的得率分别为10.4和11.6 g（按100 g原料计）。     

Routes to Potential Bioproducts from Lignocellulosic Biomass Lignin and Hemicelluloses

An essential feature of proposed fermentation-based lignocellulose to biofuel conversion processes will be the co-production of higher value chemicals from lignin and hemicellulose components. Over the years, many routes for chemical conversion of lignin and hemicelluloses have been developed by the pulp and paper industry and we propose that some of these can be applied for bioproducts manufacturing. For lignin products, thermochemical, chemical pulping, and bleaching methods for production of polymeric and monomeric chemicals are reviewed. We conclude that peroxyacid chemistry for phenol and ring-opened products looks most interesting. For hemicellulose products, preextraction of hemicelluloses from woody biomass is important and influences the mixture of solubilized material obtained. Furfural, xylitol, acetic acid, and lactic acid are possible targets for commercialization, and the latter can be further converted to acrylic acid. Pre-extraction of hemicelluloses can be integrated into most biomass-to-biofuel conversion processes.     

Enzyme hydrolysis and ethanol fermentation of liquid hot water and AFEX pretreated distillers' grains at high-solids loadings

The dry milling ethanol industry produces distiller's grains as major co-products, which are composed of unhydrolyzed and unfermented polymeric sugars. Utilization of the distiller's grains as an additional source of fermentable sugars has the potential to increase overall ethanol yields in current dry grind processes. In this study, controlled pH liquid hot water pretreatment (LHW) and ammonia fiber expansion (AFEX) treatment have been applied to enhance enzymatic digestibility of the distiller's grains. Both pretreatment methods significantly increased the hydrolysis rate of distiller's dried grains with solubles (DDGS) over unpretreated material, resulting in 90% cellulose conversion to glucose within 24h of hydrolysis at an enzyme loading of 15FPU cellulase and 40 IU beta-glucosidase per gram of glucan and a solids loading of 5% DDGS. Hydrolysis of the pretreated wet distiller's grains at 13-15% (wt of dry distiller's grains per wt of total mixture) solids loading at the same enzyme reduced cellulose conversion to 70% and increased conversion time to 72h for both LHW and AFEX pretreatments. However, when the cellulase was supplemented with xylanase and feruloyl esterase, the pretreated wet distiller's grains at 15% or 20% solids (w/w) gave 80% glucose and 50% xylose yields. The rationale for supplementation of cellulases with non-cellulolytic enzymes is given by Dien et al., later in this journal volume. Fermentation of the hydrolyzed wet distiller's grains by glucose fermenting Saccharomyces cerevisiae ATCC 4124 strain resulted in 100% theoretical ethanol yields for both LHW and AFEX pretreated wet distiller's grains. The solids remaining after fermentation had significantly higher protein content and are representative of a protein-enhanced wet DG that would result in enhanced DDGS. Enhanced DDGS refers to the solid product of a modified dry grind process in which the distiller's grains are recycled and processed further to extract the unutilized polymeric sugars. Compositional changes of the laboratory generated enhanced DDGS are also presented and discussed.