Use of a quartz crystal microbalance to investigate the antiadhesive potential of N-acetyl-L-cysteine

The reduction of bacterial biofilm formation on stainless steel surfaces by N-acetyl-L-cysteine (NAC) is attributed to effects on bacterial growth and polysaccharide production, as well as an increase in the wettability of steel surfaces. In this report, we show that NAC-coated stainless steel and polystyrene surfaces affect both the initial adhesion of Bacillus cereus and Bacillus subtilis and the viscoelastic properties of the interaction between the adhered bacteria and the surface. A quartz crystal microbalance with dissipation was shown to be a powerful and sensitive technique for investigating changes in the applied NAC coating for initial cell surface interactions of bacteria. The kinetics of frequency and dissipation shifts were dependent on the bacteria, the life cycle stage of the bacteria, and the surface. We found that exponentially grown cells gave rise to a positive frequency shift as long as their cell surface hydrophobicity was zero. Furthermore, when the characteristics of binding between the cell and the surface for different growth phases were compared, the rigidity increased from exponentially grown cells to starved cells. There was a trend in which an increase in the viscoelastic properties of the interaction, caused by the NAC coating on stainless steel, resulted in a reduction in irreversibly adhered cells. Interestingly, for B. cereus that adhered to polystyrene, the viscoelastic properties decreased, while there was a reduction in adhered cells, regardless of the life cycle stage. Altogether, NAC coating on surfaces was often effective and could both decrease the initial adhesion and increase the detachment of adhered cells and spores. The most effective reduction was found for B. cereus spores, for which the decrease was caused by a combination of these two parameters.     

Effects of DNP on the cell surface properties of marine bacteria and its implication for adhesion to surfaces

The effect of 2, 4-dinitrophenol (DNP) on the extracelluar polysaccharides (EPS), cell surface charge, and the hydrophobicity of six marine bacterial cultures was studied, and its influence on attachment of these bacteria to glass and polystyrene was evaluated. DNP treatment did not influence cell surface charge and EPS production, but had a significant effect on hydrophobicity of both hydrophilic (p = 0.05) and hydrophobic (p = 0.01) cultures. Significant reduction in the attachment of all the six cultures to glass (p = 0.02) and polystyrene (p = 0.03) was observed after DNP treatment. Moreover, hydrophobicity but not the cell surface charge or EPS production influenced bacterial cell attachment to glass and polystyrene. From this study, it was evident that DNP treatment influenced bacterial cell surface hydrophobicity, which in turn, reduced bacterial adhesion to surfaces.     

Effects of DNP on the cell surface properties of marine bacteria and its implication for adhesion to surfaces

Abstract

The effect of 2, 4-dinitrophenol (DNP) on the extracelluar polysaccharides (EPS), cell surface charge, and the hydrophobicity of six marine bacterial cultures was studied, and its influence on attachment of these bacteria to glass and polystyrene was evaluated. DNP treatment did not influence cell surface charge and EPS production, but had a significant effect on hydrophobicity of both hydrophilic (p = 0.05) and hydrophobic (p = 0.01) cultures. Significant reduction in the attachment of all the six cultures to glass (p = 0.02) and polystyrene (p = 0.03) was observed after DNP treatment. Moreover, hydrophobicity but not the cell surface charge or EPS production influenced bacterial cell attachment to glass and polystyrene. From this study, it was evident that DNP treatment influenced bacterial cell surface hydrophobicity, which in turn, reduced bacterial adhesion to surfaces.     

High potential of adhesion to abiotic and biotic materials in fish aquaculture facility by Vibrio alginolyticus strains

Aims:  The ability of Vibrio alginolyticus strains isolated from Sparus aurata and Dicentrarchus labrax nursery to adhere to epithelial cell lines (Hep-2 and Caco-2), fish mucus and their ability to form a biofilm on different surfaces (glass, polystyrene, polyethylene and polyvinyl-chloride) was investigated in this study.
Methods and Results:  The extracellular products were rich in enzymes and the strains were haemolytic on Wagatsuma agar and possessed several hydrolytic exoenzymes such as proteases, DNase and lipases. Most strains tested were multiresistant to the 17 antibiotics tested including those used in the farm to treat vibriosis.
Conclusions:  These bacteria were able to form a biofilm on all the surfaces tested and the cell density was the highest on the PVC surface followed by that on the glass slides, polystyrene and the polyethylene surface. More than 50% of the tested strains were adhesive to the epithelial cell lines (Hep-2 and Caco-2).
Significance and Impact of the Study:  These properties allow these bacteria to survive, proliferate and persist in all stages of fish rearing nursery even after seawater treatment with UV light.     

Electrophoretic mobility and hydrophobicity as a measured to predict the initial steps of bacterial adhesion

The relationship between physiochemical surface parameters and adhesion of bacterial cells to negatively charged polystyrene was studied. Cell surface hydrophobicity and electrokinetic potential were determined by contact angle measurement and electrophoresis, respectively. Both parameters influence cell adhesion. The effect of the electrokinetic potential increases with decreasing hydrophobicity. Cell surface characteristics determining adhesion are influenced by growth conditions. At high growth rates, bacterial cells tend to become more hydrophobic. This fact can be of ecological significance for controlling the spread of bacteria throughout the environment.     

Electrophoretic mobility and hydrophobicity as a measured to predict the initial steps of bacterial adhesion.

The relationship between physiochemical surface parameters and adhesion of bacterial cells to negatively charged polystyrene was studied. Cell surface hydrophobicity and electrokinetic potential were determined by contact angle measurement and electrophoresis, respectively. Both parameters influence cell adhesion. The effect of the electrokinetic potential increases with decreasing hydrophobicity. Cell surface characteristics determining adhesion are influenced by growth conditions. At high growth rates, bacterial cells tend to become more hydrophobic. This fact can be of ecological significance for controlling the spread of bacteria throughout the environment.     

Substratum/bacterial interactions and larval attachment: Films and exopolysaccharides of Halomonas marina (ATCC 25374) and their effect on barnacle cyprid larvae,Balanus amphitrite Darwin

Laboratory experiments were conducted to study the interaction between adhesion of the bacterium Halomonas marina to substrata of different wettabilities, the combination of which has been demonstrated to influence the attachment response of cyprid larvae of the barnacle Balanus amphitrite. Cyprid attachment in the presence of bacterial films was shown to be inhibited when films were on polystyrene but not on tissue‐culture polystyrene or glass. Using an enzyme‐linked lectin assay, bacteria on polystyrene showed an increase in binding of the lectin concanavalin A compared to bacteria on tissue‐culture treated polystyrene, indicating a difference in surface polymers associated with H. marina when attached to different substrata. Although bacterial growth supernatants when adsorbed to polystyrene were inhibitory to barnacle attachment, exopolysaccharides, to which the lectins may be binding, were not inhibitory. The data indicate that adhesion of films of bacteria to polystyrene alters the exopolymer production by H. marina and it is suggested that this change may be involved in the inhibition of cyprid attachment. However, the inhibition of cyprid larvae does not appear to be associated with the exopolysaccharides of the bacterium.     

Desorption of adherent bacteria from a solid hydrophobic surface by oil

Oils efficiently desorbed bacteria from a solid surface (polystyrene). Desorption was measured qualitatively by staining techniques, and quantitatively by following the outgrowth kinetics of cells remaining on the plastic surface following the washing procedure. Approximately 97% of Acinetobacter calcoaceticus RAG-1 cells adhering to a polystyrene cuvette were removed following two successive washings in the presence of olive oil.s Results suggest that oils may serve as potent, non-toxic desorbing agents to remove attached hydrophobic bacteria from surfaces.     

A microautoradiographic study of the activity of attached and free-living bacteria

Microautoradiography, combined with epifluorescent microscopy, was used to evaluate the uptake of tritiated amino acids by a marine Pseudomonas sp. A comparison was made between the activity of bacteria free-living in the medium and bacteria which were attached to glass, polyethylene or polystyrene substrata. The proportion of active bacteria was lower for free-living cells (53–82%) and those attached to polystyrene (53–76%) than for those attached to glass (77–99%) or polyethylene (73–96%). For bacteria attached to glass, assimilated labelled substrate was retained within the cell over 3 h, whereas with polyethylene, labelled material was released from the cells and adsorbed on the surrounding substratum. Hence the physiological activity of attached bacteria depended on the chemical composition of the substratum.     

Cell surface hydrophobicity and slime production of Staphylococcus epidermidis Brazilian isolates

The cell surface hydrophobicity of 60 isolates and three reference strains of Staphylococcus epidermidis was assayed by means of bacterial aggregation in liquid broth, phosphate-buffered saline, and in ammonium sulfate, as well as by affinity of the bacteria to n-hexadecane and polystyrene surfaces. In order to better characterize the isolates, the influence of bacterial growth time and enzyme treatment on cell hydrophobicity and the analysis of the slime production were also investigated. The strains presented the following profiles when assayed by the ammonium sulfate aggregation test (SAT): SAT < 1M, SAT 1M - <2M, SAT 2M - <4M, and SAT >or=4M. When SAT < 1M, the strains showed positive results for most of the cell surface hydrophobicity tests. None of the strains belonging to the groups with SAT >or= 1M showed spontaneous aggregation (SA), auto-aggregation (AA), or glass adherence, albeit 32 (62.7%) strains were polystyrene adherent and 42 (82.3%) presented weak adherence to n-hexadecane (>20%). The best correlation of the results was found among the AA and glass adherence tests (100%), followed by SA/ glass adherence (98%) and SA/ AA test (98%). The polystyrene adherence test and microbial adherence to n-hexadecane test (MATH) showed 78% correlation. Proteinase K treatment reduced bacterial adherence to polystyrene, but did not influence the SAT values. Three distinct groups of strains were distinguished by the polystyrene micromethod and glass tube adherence assay: 0.0-0.4 O.D. group, including non-glass adherent isolates; 0.5-0.7 O.D. group, including strains with variable profiles (adherent or non-adherent); and 0.8-1.3 O.D. group, composed of glass-adherent strains. Evaluation by a single method seemed not to reliably determine the surface hydrophobicity characteristics of S. epidermidis clinical isolates. Auto-aggregation properties of the strains that adhered to glass seemed related to slime expression, rather than cell surface hydrophobicity. Data also suggested involvement of protein components in adherence to polystyrene, but not in auto-aggregation properties assayed by SAT.     

Moving fluid with bacterial carpets

We activated a solid-fluid interface by attaching flagellated bacteria to a solid surface. We adsorbed swarmer cells of Serratia marcescens to polydimethylsiloxane or polystyrene. The cell bodies formed a densely packed monolayer while their flagella continued to rotate freely. Motion of the fluid close to an extended flat surface, visualized with tracer beads, was dramatically enhanced compared to the motion farther away. The tracer beads revealed complex ever-changing flow patterns, some linear (rivers), others rotational (whirlpools). Typical features of this flow were small (tens of micro m) and reasonably stable (many minutes). The surface performed active mixing equivalent to diffusion with a coefficient of 2 x 10(-7) cm(2)/s. We call these flat constructs "bacterial carpets". When attached to polystyrene beads or to fragments of polydimethylsiloxane, the bacteria generated both translation and rotation. We call these constructs "auto-mobile beads" or "auto-mobile chips". Given the size and strength of the flow patterns near the carpets, the motion must be generated by small numbers of coordinated flagella. We should be able to produce larger and longer-range effects by increasing coordination.     

Antimicrobial activity of tertiary amine covalently bonded to a polystyrene fiber.

Tertiary amine was covalently bonded to a polystyrene fiber and examined for antibacterial activity. The tertiary amine covalently bonded to a polystyrene fiber (TAF) showed a high antimicrobial activity against Escherichia coli. TAF exhibited a stronger antibacterial activity against gram-negative bacteria (E. coli, Pseudomonas aeruginosa, Klebsiella pneumoniae, Salmonella typhimurium, and Serratia marcescens) than against gram-positive bacteria (Staphylococcus aureus and Streptococcus faecalis) or Candida albicans. This activity against E. coli was accentuated by 0.1% deoxycholate or 10 mg of actinomycin D per ml, to which E. coli is normally not susceptible. This implies that TAF causes an increase of the bacterial outer membrane permeability. On the other hand, the antimicrobial activity was inhibited by adding Mg2+ or by lowering the pH. This suggest an electrostatic interaction between the bacterial cell wall and TAF. Scanning electron microscopy showed that E. coli cells were initially attached to TAF, with many projections on the cell surface, but then were apparently lysed after contact for 4 h. Taken together, these results imply that bacteria initially interact with TAF by an electrostatic force between the anionic bacterial outer membrane and the cationic tertiary amine residues of TAF and that longer contact with TAF damages the bacterial outer membrane structure and increases its permeability.     

Rapid identification of biosurfactant-producing bacterial strains using a cell surface hydrophobicity technique

Rapid identification of biosurfactant-producing bacterial strains was achieved by assaying cell surface hydrophobicity which had a direct correlation with biosurfactant production by Serratia marcescens, Pseudomonas aeruginosa, Bacillus pumilus, B. laterosporus, Acineto- bacter calcoaceticus, Escherichia coli and Staphylococcus aureus. These properties namely, Hydrophobic Interaction Chromatography, Salt Aggregation Test, Bacterial Adherence To Hydrocarbon and adhesion to polystyrene by Replica Plate test, provide a simple means for identifying bacteria associated with the production of biosurfactants.     

Surface thermodynamics of bacterial adhesion.

The adhesion of five strains of bacteria, i.e., Staphylococcus aureus (strain 049), Staphylococcus epidermidis (strain 047), Escherichia coli (strains 055 and 2627), and Listeria monocytogenes, to various polymeric surfaces was studied. The design of the experimental protocol was dictated by thermodynamic considerations. From the thermodynamic model for the adhesion of small particles from a suspension onto a solid substratum, it follows that the extent of adhesion is determined by the surface properties of all three phases involved, i.e., the surface tensions of the adhering particles, of the substrate, and of the suspending liquid medium. In essence, adhesion is more extensive to hydrophilic substrata (i.e., substrata of relatively high surface tension) than to hydrophobic substrata, when the surface tension of the bacteria is larger than that of the suspending medium. When the surface tension of the suspending liquid is larger than that of the bacteria, the opposite pattern of behavior prevails. Suspensions of bacteria at a concentration of 10(8) microorganisms per ml were brought into contact with several polymeric surfaces (Teflon, polyethylene, polystyrene, and acetal and sulfonated polystyrene) for 30 min at 20 degrees C. After rinsing, the number of bacteria adhering per unit surface area was determined by image analysis. The surface tension of the suspending medium. Hanks balanced salt solution, was modified through the addition of various amounts of dimethyl sulfoxide. It was found that the number of bacteria adhering per unit surface area correlates well with the thermodynamic predictions and that these data may be used to determine the surface tension of the different bacterial species. The surface tensions of the bacteria obtained in this fashion are in excellent agreement with those obtained by other methods.     

Growth of endothelial and HeLa cells on a new multipurpose microcarrier that is positive,negative or collagen coated

A new cell culture microcarrier that can be covalently bonded by cell attachment proteins and can be thin-sectioned for electron microscopy was synthesized. It was easily made by sulfonating cross-linked polystyrene beads for a negative surface charge followed by covalent attachment of polyethylenimine for a positive charge. Cell attachment proteins, e.g. collagen, was covalently bonded directly to the microcarrier using a carbodiimide or after activating the microcarrier surface with glutaraldehyde. HeLa-S3 cells attached, spread and grew to confluence more efficiently on the positive microcarriers and those coated with collagen than on the negative ones. Endothelial cells grew best on those with a negative surface charge. The nature of the microcarrier surface was not the only aspect involved in cell adhesion but also the type of serum proteins adsorbed. Qualitatively different proteins coated the microcarriers depending upon whether the carrier was negative, positive or coated with collagen. Comparison of various types of available microcarriers indicated that the modified cross-linked polystyrene beads used here were best for transmission and scanning electron microscopy. Endothelial cells grown on the microcarriers had the same ultrastructure as cells grown in monolayers in culture dishes. Of a variety of microcarriers tested the modified cross-linked polystyrene beads were the only ones that could be used for both ultrastructural and biochemical techniques.     

Use of a novel Chlamydomonas mutant to demonstrate that flagellar glycoprotein movements are necessary for the expression of gliding motility

As an alternative to swimming through liquid medium by the coordinated bending activity of its two flagella, Chlamydomonas can exhibit whole cell gliding motility through the interaction of its flagellar surfaces with a solid substrate. The force transduction occurring at the flagellar surface can be visualized as the saltatory movements of polystyrene microspheres. Collectively, gliding motility and polystyrene microsphere movements are referred to as flagellar surface motility. The principal concanavalin A binding, surface-exposed glycoproteins of the Chlamydomonas reinhardtii flagellar surface are a pair of glycoproteins migrating with apparent molecular weight of 350 kDa. It has been hypothesized that these glycoproteins move within the plane of the flagellar membrane during the expression of flagellar surface motility. A novel mutant cell line of Chlamydomonas (designated L-23) that exhibits increased binding of concanavalin A to the flagellar surface has been utilized in order to restrict the mobility of the concanavalin A-binding flagellar glycoproteins. Under all conditions where the lateral mobility of the flagellar concanavalin A binding glycoproteins is restricted, the cells are unable to express whole cell gliding motility or polystyrene microsphere movements. Conversely, whenever cells can redistribute their concanavalin A binding glycoproteins in the plane of the flagellar membrane, they express flagellar surface motility. Since the 350 kDa glycoproteins are the major surface-exposed flagellar proteins, it is likely that most of the signal being followed using fluorescein isothiocyanate (FITC)-concanavalin A is attributable to these high molecular weight glycoproteins.(ABSTRACT TRUNCATED AT 250 WORDS)     

Cell Surface Hydrophobicity and Slime Production of <Emphasis Type="Italic">Staphylococcus epidermidis</Emphasis> Brazilian Isolates

The cell surface hydrophobicity of 60 isolates and three reference strains of Staphylococcus epidermidis was assayed by means of bacterial aggregation in liquid broth, phosphate-buffered saline, and in ammonium sulfate, as well as by affinity of the bacteria to n-hexadecane and polystyrene surfaces. In order to better characterize the isolates, the influence of bacterial growth time and enzyme treatment on cell hydrophobicity and the analysis of the slime production were also investigated. The strains presented the following profiles when assayed by the ammonium sulfate aggregation test (SAT): SAT < 1M, SAT 1M − <2M, SAT 2M − <4M, and SAT ≥4M. When SAT < 1M, the strains showed positive results for most of the cell surface hydrophobicity tests. None of the strains belonging to the groups with SAT ≥ 1M showed spontaneous aggregation (SA), auto-aggregation (AA), or glass adherence, albeit 32 (62.7%) strains were polystyrene adherent and 42 (82.3%) presented weak adherence to n-hexadecane (>20%). The best correlation of the results was found among the AA and glass adherence tests (100%), followed by SA/ glass adherence (98%) and SA/ AA test (98%). The polystyrene adherence test and microbial adherence to n-hexadecane test (MATH) showed 78% correlation. Proteinase K treatment reduced bacterial adherence to polystyrene, but did not influence the SAT values. Three distinct groups of strains were distinguished by the polystyrene micromethod and glass tube adherence assay: 0.0–0.4 O.D. group, including non-glass adherent isolates; 0.5–0.7 O.D. group, including strains with variable profiles (adherent or non-adherent); and 0.8–1.3 O.D. group, composed of glass-adherent strains. Evaluation by a single method seemed not to reliably determine the surface hydrophobicity characteristics of S. epidermidis clinical isolates. Auto-aggregation properties of the strains that adhered to glass seemed related to slime expression, rather than cell surface hydrophobicity. Data also suggested involvement of protein components in adherence to polystyrene, but not in auto-aggregation properties assayed by SAT. Received: 13 May 2002 / Accepted: 5 July 2002     

Involvement of N-acetyl-D-galactosamine-specific lectin in biofilm formation by the periodontopathogenic bacterium, Eikenella corrodens

Eikenella corrodens is known not only as one of the periodontopathogenic bacteria but also as a pathogen associated with many infectious diseases of humans. Dental plaque is a complex biofilm community comprised of many bacterial species. E. corrodens has a lectin on its cell surface that is thought to be involved in its pathogenicity. In this study, we found that E. corrodens forms a biofilm on a polystyrene surface. A biofilm was formed at the bottom of the wells in microtiter plates after 24 h. Microcolonies were observed as the amount of biofilm became larger. When anaerobic respiration was repressed due to nitrate limitation, the biofilm formed only at the air-water interface. Strain 1073 and HU, which have higher lectin activity, formed a biofilm more effectively than other strains. Biofilm formation was repressed by the addition of N-acetyl-D-galactosamine. These results suggest that the lectin on the surface of E. corrodens might be involved in biofilm formation.     

Identification of the ligand-binding domain of the surface-located fibrinogen receptor (clumping factor) of Staphylococcus aureus

The ability of Staphylococcus aureus to bind to fibrinogen and fibrin is believed to be an important factor in the initiation of foreign-body and wound Infections. Recently, we reported the cloning and sequencing of the gene clfA encoding the fibrinogen receptor (clumping factor, ClfA) of S. aureus strain Newman and showed that the gene product was responsible for the clumping of bacteria in soluble fibrinogen and for the adherence of bacteria to solid-phase fibrinogen. This was confirmed here by showing that antibodies raised against purified Region A inhibited both of these properties. Also, immunofluorescent microscopic analysis of wild-type Newman and a clfA::Tn917 mutant of Newman with anti-ClfA Region A sera confirmed that Region A is exposed on the bacterial cell surface. Furthermore, polystyrene beads coated with the Region A protein formed clumps in soluble fibrinogen showing that the ClfA protein alone is sufficient for the clumping phenotype. Western immunoblotting with anti-ClfA Region A antibodies identified the native ClfA receptor as a 185 kDa protein that was released from the cell wall of S. aureus by lysostaphin treatment. A single extensive ligand-binding site was located within Region A of the ClfA protein. Truncated ClfA proteins were expressed in Escherichia coli. Lysates of E. coli and proteins that had been purified by affinity chromatography were tested for (i) their ability to bind fibrinogen in Western ligand blotting experiments, (ii) for their ability to inhibit clumping of bacteria in fibrinogen solution and adherence of bacteria to solid-phase fibrinogen, and (iii) for their ability to neutralize the blocking activity of anti-ClfA Region A antibody. These tests allowed the ligand-binding domain to be localized to a 218-residue segment (residues 332-550) within Region A.     

Use of a gelatin substrate for culturing diploid human skin fibroblasts

Gelatin coating of the growth surface of commercially available polystyrene Petri dishes is proposed for successful cultivation of human skin fibroblasts. A comparison of culture growth dynamics on gelatin, glass and polystyrene allowed to recommend gelatin as the substrate in order to receive an abundant similar material with a low population density viability. The absence of changes in carbohydrate metabolism changes during cell culturing on gelatin provides an opportunity to use these cells in studying regulation of carbohydrate metabolism.