膜前助滤预处理对高藻水微滤膜污染的影响研究

研究采用添加硅藻土、植物棉、活性炭等3种不同预处理手段来过滤铜绿微囊藻,并考察未预处理及预处理后的藻液过滤过程中的过滤特性、有机物分布及膜污染特性。结果表明, 3种预处理手段对过滤通量均有所提高并减缓膜污染。其中,硅藻土预处理提高平均过滤通量达915%,明显优于其他助滤手段。活性炭预处理能够有效吸附芳香族蛋白质类荧光污染物,显著降低污染膜的不可逆化学污染阻力。通过OCT及SEM分析可知未预处理的高藻水直接过滤造成的膜污染最严重,饼层结构的粗糙度最低并且厚度也最小,而硅藻土通过优化饼层结构以达到缓解膜污染的效果。最后基于XDLVO理论结果也进一步证实硅藻土预处理手段对改善膜污染效果最好。研究结果对未来蓝藻水华膜处理技术的预处理手段研发具有指导意义。     

海洋中的凝集网与透明胞外聚合颗粒物

透明胞外聚合颗粒物(TEP)是海洋中大量存在的能被爱尔新蓝(alcian blue)染色的由酸性多糖组成的透明胶状颗粒物,主要来源于浮游植物,由于其透明的特性而被长期忽视。TEP同时具有胶体和颗粒物的特性。作为胶体,TEP为细菌提供了栖息场所与降解基质,同时TEP可以吸收痕量元素,以改变这些元素的生物地球化学过程。作为颗粒物,TEP可以聚集并沉降,由于其高的碳含量,会在很大程度上影响海洋的碳通量。由于TEP可以被中型浮游动物所摄食,所以TEP可以连接并缩短微食物环和经典食物链,在海洋生态系统中起很重要的作用。介绍了TEP的定义、测量方法、来源、形成、及其与浮游植物的关系和其生态功能。     

Microbial community and biomass characteristics associated severe membrane fouling during start-up of a hybrid anoxic-oxic membrane bioreactor

In MBR, severe membrane fouling is often observed in the initial phase in which biomass is yet fully acclimated and stabilized in terms of microbial community structure and biomass characteristics. The focus of this study was to investigate the microbial community development and its influence on biomass characteristics and membrane fouling during start-up of a hybrid anoxic-oxic MBR. PCR-DGGE analysis indicated that the microbial community shifted in start-up period when a severe membrane fouling was observed. Small particle size, high fractal dimension (DF) and high EPS production, which were closely associated with microbial community, were found to be the major contributors to the severe fouling. Microbial community development was most likely the ultimate factor responsible for the severe membrane fouling.     

Exopolymer production as a function of cell permeability and death in a diatom (Thalassiosira weissflogii) and a cyanobacterium (Synechococcus elongatus)

Exopolymer particles are found throughout the ocean and play a significant biogeochemical role in carbon cycling. Transparent exopolymer particles (TEP) are composed of acid polysaccharides, and Coomassie staining particles (CSP) are proteins. TEPs have been extensively studied in the ocean, while CSP have been largely overlooked. The objective of this research was to determine the role of stress and cell permeability in the formation of TEP and CSP. The diatom Thalassiosira weissflogii and cyanobacterium Synechococcus elongatus were grown in batch cultures and exposed to hydrogen peroxide (0, 10, and 100 μM) as an environmental stressor. There was no correlation between TEP and CSP concentrations, indicating that they are different populations of particles rather than different chemical components of the same particles. CSP concentrations were not affected by hydrogen peroxide concentration and did not correlate with indicators of stress and cell death. In contrast, TEP concentrations in both taxa were correlated with a decrease in the effective quantum yield of photosystem II, increased activity of caspase‐like enzymes, and an increase in the proportion of the population with permeable cell membranes, indicating that TEP production was associated with the process of cell death. These data show that different environmental factors and physiological processes affected the production of TEP and CSP by phytoplankton. TEP and CSP are separate populations of exopolymer particles with potentially different biogeochemical roles in the ocean.     

膜生物反应器的研究进展

膜生物反应器是近年来发展的废水处理新技术,具有活性污泥浓度高、污泥龄长、占地面积小、投资省的特点。利用膜生物反应器进行污水处理不仅可以大大节约水资源,还可以大大节约能源,节省设备和运行费用,已成为二十一世纪研究热点。膜生物反应器是通过高效膜分离技术与活性污泥相结合,增大污泥中的特效菌来加快生化反应速率,提高废水处理效果。目前处理对象已从生活污水扩展到高浓度的有机废水和难降解的工业废水。本文综述了膜生物反应器在废水中的应用研究情况,并分析比较了各种膜材质的特点、适用范围以及膜的污染因素和清洗方法,展望了膜生物反应器的应用前景及进一步研究方向。     

Evaluation of soluble microbial products (SMP) on membrane fouling in membrane bioreactors (MBRs) at the fractional and overall level: a review

Membrane fouling by soluble microbial products (SMP) remains one of the limitations for widespread applications of membrane bioreactor (MBR) systems. Over the past two decades, the characteristics and behaviors of SMP have attracted much attention, and efforts have been dedicated to clarify their role in membrane fouling in MBRs. However, to date, there are only few reviews directly relating this area, and the objective of previous reviews is to concentrate on SMP and their implications in biological treatment systems and their effluents. This brief review relating only to SMP-caused membrane fouling evaluation at the fractional level (SMP key components, sub-fractions and hydrophilic and hydrophobic fractions) and at the overall level (SMP overall roles, characteristics and factors) is presented, which could greatly help researchers and engineers to better understand SMP actual contribution to membrane fouling and adopt effective measures to avoid SMP-caused fouling in MBRs.     

藻源污染物特性对高藻水微滤处理过程中膜污染的影响

采用不同生长时期的藻细胞、藻源型有机物(AOM)及原藻液进行过滤实验,研究不同生长时期的藻源污染物对膜污染的影响特性及机制。利用UMFI法分析不同生长时期的藻细胞、AOM及原藻液的污染程度;采用CRITIC分析法定量分析了不同生长时期的AOM和藻细胞在混合过滤过程中对膜污染的贡献率,同时采用混合污染堵塞模型分析了不同生长时期的原藻液不同过滤阶段的主要污染堵塞类型。结果表明, 3个生长时期的藻细胞及AOM的膜污染程度均为对数期最轻;值得注意的是,在原藻液过滤过程中藻细胞及AOM的膜污染贡献率随着生长时期的不同而有所变化,其中AOM的污染权重随着生长时期的延长不断减小,而藻细胞的污染权重随着生长时期的延长不断增大。不同生长时期的原藻液过滤过程中均呈现两段式污染堵塞类型,并且后段均为滤饼堵塞。研究不仅阐明了藻源型污染物特性对微滤处理高藻水膜污染的影响机制,同时也为改善膜污染的技术开发提供参考。     

Impact of protein fouling on nanoparticle capture within the Viresolve® Pro and Viresolve® NFP virus removal membranes

Virus filtration is a robust size-based technique that can provide the high level of viral clearance required for the production of mammalian-derived biotherapeutics such as monoclonal antibodies. Several studies have shown that the retention characteristics of some, but not all, virus filters can be significantly affected by membrane fouling, but there have been no direct measurements of how protein fouling might alter the location of virus capture within these membranes. The objective of this study was to directly examine the effect of protein fouling by human immunoglobulin G (IgG) on virus capture within the Viresolve® Pro and Viresolve® NFP membranes by scanning electron microscopy using different size gold nanoparticles. IgG fouling shifted the capture location of 20 nm gold nanoparticles further upstream within the Viresolve® Pro filter due to the constriction and/or blockage of the pores in the virus retentive region of the filter. In contrast, IgG fouling had no measurable effect on the capture of 20 nm nanoparticles in the Viresolve® NFP membrane, and IgG fouling had no effect on the capture of larger 40 and 100 nm nanoparticles in either membrane. These results provide important insights into how protein fouling alters the virus retention characteristics of different virus filters.     

Influence of elevated pH shocks on the performance of a submerged anaerobic membrane bioreactor

The effects of elevated pH shocks on the performance and membrane fouling of a submerged anaerobic membrane bioreactor (SAnMBR) treating thermomechanical pulping (TMP) whitewater was studied over a 120-day period. Changes in chemical oxygen demand (COD) removal, biogas production, sludge and cake layer properties, and their correlations to membrane fouling – before and after pH shocks – were systematically studied using various analytical tools. The results showed that a pH 8.0 shock had a minor impact, while pH 9.1 and 10.0 shocks exerted significant long-lasting negative impacts on COD removal, biogas production and membrane filtration performance of the SAnMBR. When the normal pH (7.0) was resumed, it took approximately 1, 6, and 30 days for the performance to recover for pH 8.0, 9.1 and 10.0 shocks, respectively. The elevated pH shocks induced the dispersion of sludge flocs and resulted in the accumulation of colloids and solutes or biopolymers in the sludge suspension, and thus deteriorated membrane performance. Statistical analysis showed that the ratio of proteins (PN) to polysaccharides (PS) in extracellular polymeric substances (EPS) had a strongly negative effect on the membrane fouling rate. There were smaller size particles deposited on the membrane surface and a more compact and denser cake layer was formed after being exposed to an alkaline shock at pH 10, resulting in higher membrane fouling rates.     

Transparent exopolymer particle production and aggregation by a marine planktonic diatom (Thalassiosira weissflogii) at different growth rates

Transparent exopolymer particles (TEP) play an important role in the ocean carbon cycle as they are sticky and affect particle aggregation and the biological carbon pump. We investigated the effect of growth rate on TEP production in nitrogen limited semi‐continuous cultures of the diatom Thalassiosira weissflogii (Grunow) G. Fryxell & Hasle. Steady‐state diatom concentrations and other indicators of biomass (chl a, and total carbohydrate) were inversely related to growth rate, while individual cell volume increased with growth rate. There was no change in total TEP area with growth rate; however, individual TEP were larger at high growth rates and the number of individual TEP particles was lower. TEP concentration per cell was higher at higher growth rates. SYTOX Green staining showed that <5% of the diatom population had permeable cell membranes, with the proportion increasing at low growth rates. However, TEP production rates were greater at high growth rates, refuting our hypothesis that TEP formation is dependent on dying cells with compromised cell membranes in a diatom population. Measurements of particle size distribution in the cultures using laser scattering showed that they were most aggregated at high growth rates. These results indicate a coupling between TEP production and growth rate in diatoms under N limitation, with fast growing T. weissflogii producing more TEP and aggregates.     

Does the marine copepod Calanus pacificus consume transparent exopolymer particles (TEP)?

Gel-like transparent exopolymer particles (TEP) formed frompolysaccharides exuded copiously by natural phytoplankton andbacteria occur ubiquitously in sea water, but the utilizationof these particles as a food source by zooplankton is poorlyknown. The common marine calanoid copepod Calanus pacificusconsumed TEP and produced abundant fecal pellets when TEP wereoffered both alone and in the presence of diatom cells. TEPconsumption increased with TEP concentration and the presenceof TEP did not inhibit ingestion of cells. However, becauseof their low carbon content, TEP contributed only 15% to totalcarbon consumption in the presence of phytoplankton food. Whilecopepods consumed pure TEP in this study, sticky TEP in naturecontain abundant inclusions of bacteria and microorganisms toosmall for copepods to capture individually. Thus, consumptionof TEP may be most significant as a mechanism by which carbonmay be shunted from the microbial loop to higher trophic levels.     

Virus attachment to transparent exopolymeric particles along trophic gradients in the southwestern lagoon of New Caledonia

Viruses on organic aggregates such as transparent exopolymeric particles (TEP) are not well investigated. The number of TEP-attached viruses was assessed along trophic gradients in the southwestern lagoon of New Caledonia by determining the fraction of viruses removed after magnetic isolation of TEP. In order to isolate TEP magnetically, TEP were formed in the presence of magnetic beads from submicrometer precursors collected along the trophic gradients. The mixed aggregates of TEP-beads-viruses were removed from solution with a magnetic field. The percentage of viruses associated with newly formed TEP averaged 8% (range, 3 to 13%) for most of the stations but was higher (ca. 30%) in one bay characterized by the low renewal rate of its water mass. The number of viruses (N) attached to TEP varied as a function of TEP size (d [in micrometers]) according to the formulas N = 100d(1.60) and N = 230d(1.75), respectively, for TEP occurring in water masses with short (i.e., <40 days) and long (i.e., >40 days) residence times. These two relationships imply that viral abundance decreases with TEP size, and they indicate that water residence time influences viral density and virus-bacterium interactions within aggregates. Our data suggest that the fraction of viruses attached to TEP is highest in areas characterized by a low renewal rate of the water mass and can constitute at times a significant fraction of total virus abundance. Due to the small distance between viruses and hosts on TEP, these particles may be hot spots for viral infection.     

Change in the fouling propensity of sludge in membrane bioreactors (MBR) in relation to the accumulation of biopolymer clusters

A membrane bioreactor (MBR) and an activated sludge process (ASP) were operated side by side to evaluate the change of sludge supernatant characteristics and the evolution of the sludge fouling propensity. The MBR sludge had a higher organic concentration and more biopolymer clusters (BPC) in the supernatant compared with ASP. BPC increased in both concentration and size in the MBR. The results show that the change in the liquid-phase property had a profound effect on the sludge fouling propensity. MBR operation transformed typical activated sludge to MBR sludge with a higher fouling propensity. Distinct from the ASP, membrane filtration retained soluble microbial products (SMP) within the MBR, and the vast membrane surface provided a unique environment for the transformation of SMP to large size BPC, leading to further sludge deposition on the membrane surface. Thus, membrane filtration is the crucial cause of the inevitable fouling problem in submerged MBRs.     

Fouling in reverse osmosis (RO) membrane in water recovery from secondary effluent: a review

Reverse osmosis (RO) is the most preferable process for water recovery from secondary effluent (SE) because of its higher rejection of impurities with lower associated cost and higher quality of product. Fouling still is a major challenge during the water recovery due to higher contaminant loadings in SE and high rejection capability of this membrane. The presence of suspended solids, colloidal and organic matters, and high level of biological activities in SE further elevate fouling potentiality. This review was performed to identify major foulants causing hindrance in sustainable application of reverse osmosis and to present available pre-treatment options for these foulants. There are four fouling types present in RO namely; bio-fouling, inorganic/scaling, organic, and particulate fouling. Among them; bio-fouling is less understood but dominant since the pre-treatment options are not well developed. Other fouling mechanisms have been overcome by well developed pre-treatments. The major foulants for RO are dissolved and macromolecular organic substances, sparingly soluble inorganic compounds, colloidal and suspended particles, and micro-organisms. Some of these potential fouling water quality parameters (PFWQPs) are interrelated with each others such as electrical conductivity is a surrogate measure of total dissolved solids with established stable relationship. Most of these PFWQPs such as total suspended solids, turbidity, chemical oxygen demand can be removed by conventional pre-treatment; some such as colloidal particles and micro-organisms by modern options and even others such as endocrine disrupting compounds, pharmaceutical and personal care products are still challenging for current pre-treatments. These foulants need to be identified properly to integrate appropriate pre-treatments for minimizing fouling potentiality to increase water recovery at minimal costs.     

Influence of solids retention time on membrane fouling: characterization of extracellular polymeric substances and soluble microbial products

The objective of this study was to investigate the influence of solids retention time (SRT) on membrane fouling and the characteristics of biomacromolecules. Four identical laboratory-scale membrane bioreactors (MBRs) were operated with SRTs for 10, 20, 40 and 80 days. The results indicated that membrane fouling occurred faster and more readily under short SRTs. Fouling resistance was the primary source of filtration resistance. The modified fouling index (MFI) results suggested that the more ready fouling at short SRTs could be attributed to higher concentrations of soluble microbial products (SMP). Fourier transform infrared (FTIR) spectra indicated that the SRT had a weak influence on the functional groups of the total extracellular polymeric substances (TEPS) and SMP. However, the MBR under a short SRT had more low-molecular-weight (MW) compounds (<1 kDa) and fewer high-MW compounds (>100 kDa). Aromatic protein and tryptophan protein-like substances were the dominant groups in the TEPS and SMP, respectively.     

Comparison and Analysis of Membrane Fouling between Flocculent Sludge Membrane Bioreactor and Granular Sludge Membrane Bioreactor

The goal of this study is to investigate the effect of inoculating granules on reducing membrane fouling. In order to evaluate the differences in performance between flocculent sludge and aerobic granular sludge in membrane reactors (MBRs), two reactors were run in parallel and various parameters related to membrane fouling were measured. The results indicated that specific resistance to the fouling layer was five times greater than that of mixed liquor sludge in the granular MBR. The floc sludge more easily formed a compact layer on the membrane surface, and increased membrane resistance. Specifically, the floc sludge had a higher moisture content, extracellular polymeric substances concentration, and negative surface charge. In contrast, aerobic granules could improve structural integrity and strength, which contributed to the preferable permeate performance. Therefore, inoculating aerobic granules in a MBR presents an effective method of reducing the membrane fouling associated with floc sludge the perspective of from the morphological characteristics of microbial aggregates.     

Correlating membrane fouling with sludge characteristics in membrane bioreactors: an especial interest in EPS and sludge morphology analysis

Two submerged membrane bioreactors were operated for a period of 3 months to study the filtration behavior of normal sludge and bulking sludge. Comparison of sludge morphology and bound extracellular polymeric substances (EPS) from the two systems was made to elucidate the different filtration characteristics. Experimental results showed that the membrane fouling behavior induced by bulking sludge was more severe than normal sludge. Concomitantly, the adsorption tests and atomic force microscopy observation confirmed that the EPS properties played an important role in membrane adsorption, eventually causing the different fouling behavior. Correlations between image analysis information and diluted sludge volume index (DSVI) have been identified. The combinations of EFLI/FAI (the ratio between extended filamentous lengths and floc area), from factor and floc elongation related parameters (aspect ratio or roundness) were the preferred input candidates in autoregressive exogenous model to describe the filamentous bulking phenomena, which aided in predicting membrane fouling.     

Community composition and activity of prokaryotes associated to detrital particles in two contrasting lake ecosystems

The composition, distribution and extracellular enzyme activities of bacteria attached to small (2-50 microm in size) transparent exopolymer and Coomassie-stained proteinaceous particles (TEP and CSP) were examined in two lakes of different trophic status located in the Massif Central of France. TEP concentrations (10(4)-10(6) particle per L) were significantly higher in the more productive lake and were significantly related to chlorophyll a concentrations. The majority of TEP and CSP were colonized by bacteria that constituted 2.6% and 7.4% of the total 4',6-diamidino-2-phenylindole-stained bacteria in lakes Pavin and Aydat, respectively. In both lakes, the composition of particle-associated bacteria was different from that of free-living bacteria, the Betaproteobacteria and Bacteroidetes (i.e. former Cytophaga-Flavobacteria group) being the dominant groups on particles. We also found that 2-5 microm TEP were more colonized than 2-5 microm CSP in the two lakes, and that TEP colonization was higher in the less productive lake. Measurements of Leucine aminopeptidase and alpha-glucosidase activities in fractionated lake water (0.2-1.2, 1.2-5 and >5 microm fractions) indicated that proteolytic activity was always higher and that particle-associated bacteria have higher enzymatic activities than free-living bacteria. The glycolytic activities in the 1.2-5 and >5 microm fractions were related to the abundance of TEP. We conclude that small freshwater detrital organic particles constitute microhabitats with high bacterial activities in pelagic environments and, undoubtedly, present significant ecological implications for the prokaryotic community structure and function in aquatic ecosystems.     

A K<Superscript>+</Superscript>/H<Superscript>+</Superscript> P-ATPase transport in the accessory cell membrane of the blowfly taste chemosensilla sustains the transepithelial potential

An electrogenic K(+) transport in the tormogen cell of insect chemosensilla is involved in the generation and maintenance of the transepithelial potential (TEP). To gain more information about the K(+) transport system underlying the TEP generation and the location of its components in the plasma membrane of the tormogen cell, we studied the effects of inhibitors of K(+)/H(+) P-ATPase (bafilomycin A1, omeprazole and Na-orthovanadate), of K(+)/Cl(-) co-transport (bumetanide), of Cl(-) channels (NPPB) and of a K(+) channel blocker (BaCl(2)). The relationship between TEP amplitude and spike firing activity was also studied. Experiments were performed on the labellar chemosensilla of the blowfly Protophormia terraenovae using a modified tip-recording technique. Results show that: (a) K(+)/H(+) P-ATPase inhibitors significantly decrease the TEP, when properly applied to the labellum for 20 min, so as to reach the basolateral side of the plasma membrane, while no effect was detected when applied to the apical side, (b) bumetanide, NPPB and BaCl(2) decrease the TEP value only when administered to the apical side, (c) spike activity is positively correlated with the TEP. A model is proposed of the active and passive K(+) transports sustaining the TEP associated with the blowfly chemosensilla.     

Filtration-based perfusion of hybridoma cultures in protein-free medium: Reduction of membrane fouling by medium supplementation with DNase I

In this study, a filtration-based perfusion process was developed for the production of monoclonal antibodies (IgM) by suspended hybridoma cells grown in protein-free medium. It was found that the use of protein-free medium for perfusion culture generated the formation of numerous visible suspended particles consisting of dead cells and cellular debris aggregated into fibrous material. Surprisingly high apparent viabilities were observed in such protein-free cultures. In addition, membrane fouling occurred more rapidly in protein-free medium than in conventional serum-supplemented medium. By the addition of deoxyribonuclease I (DNase I) to the protein-free medium, it was possible to prevent the formation of aggregates and to follow the evolution of the total cell population more accurately. Moreover, DNase I significantly reduced the fouling of filtration membranes, and that, for two different types of separation systems (cross-flow and vortex-flow filtration) and two different types of membranes (polycarbonate and hydrophilized polysultone). From these results, it is clear that the presence of DNA fragments liberated following cellular death is playing an important role in membrane fouling. Longevity of filtration membranes was found to be considerably greater using a vortex-flow filtration module than with a static plate-and-frame cross-flow filtration module. The use of vortex-flow filtration of conjuction with DNase I allowed maintenance of perfusion cultures for more than 1 month without membrane fouling or antibody retention and with a constant permeate IgM concentration of 250 mg/L. Hybridomacells appeared to gradually adapt to increasing rotational speed in the vortex-flow filtration module.