RF discharge-based plasma emitter

An injector of hydrogen atoms for plasma diagnostics in modern tokamaks has been developed at the Budker Institute of Nuclear Physics (Novosibirsk). The ion source of the injector produces a proton (helium ion) beam with a current of up to 2 A (1 A), an ion energy of up to 55 keV, a beam divergence of ～0.6\deg, and a pulse duration of up to 10 s. An RF discharge-based plasma emitter, which is one of the main parts of the ion source, is described. The emitter diameter is 72 mm, the ion current density is 120 mA/cm², and the inhomogeneity of the current density is ±6%. The beam is formed by a four-electrode ionoptical system with 163 round apertures. At a current of 2 A, the ion beam consists of 67% protons, 18% H ₂ ⁺ ions, and 15% H ₃ ⁺ ions, the total content of heavier ions in the beam being no higher than 2–3%.     

Improving hydrogen production in microbial electrolysis cells through hydraulic connection with thermoelectric generators

Using alternative power sources to drive hydrogen production in microbial electrolysis cells (MECs) is important to implementation of MEC technology. Herein, thermoelectric generators (TEG) were to power MECs using simulated waste heat. With the MEC anolyte as a cold source for TEG, current generation of the MEC increased to 2.46 ± 0.06 mA and hydrogen production reached 0.14 m³ m⁻³ d^-1, higher than those of the TEG-MEC system without hydraulic connection (1.16 ± 0.07 mA and 0.07 ± 0.01 m³ m⁻³ d^-1). A high recirculation rate of 30 mL min^-1 doubled both current generation and hydrogen production with 10 mL min^-1, benefited from a stronger cooling effect that increased the TEG voltage output. However, the optimal recirculation rate was determined as 20 mL min^-1 because of comparable performance but potentially less energy requirement. Reducing anolyte hydraulic retention time to 4 h has increased hydrogen production to 0.25 ± 0.05 m³ m⁻³ d^-1 but decreased organic removal efficiency to 69 ± 2%. Adding three more TEG units that captured more heat energy further enhanced hydrogen production to 0.36 m³ m⁻³ d^-1. Those results have demonstrated a successful integration of TEG with MEC through both electrical and hydraulic connections for simultaneous wastewater treatment and energy recovery.     

Metabolic and energetic aspects of biohydrogen production of Clostridium tyrobutyricum: The effects of hydraulic retention time and peptone addition

This study evaluates the microbial metabolism and energy demand in fermentative biohydrogen production using Clostridium tyrobutyricum FYa102 at different hydraulic retention times (HRT) over a period of 1-18 h. The hydrogen yield shows a positive correlation with the butyrate yield, the B/A ratio, and the Y_H2/2(Y_HAc+Y_HBu) ratio, but a negative correlation with the lactate yield. A decrease in HRT, which is accompanied by an increased biomass growth, tends to decrease the B/A ratio, due presumably to a higher energy demand for microbial growth. The production of lactate at a low HRT, however, may involve an unfavorable change in e⁻ equiv distribution to result in a reduced hydrogen production. Finally, the relatively high hydrogen yields observed in the bioreactor with the peptone addition may be ascribed to the utilization of peptone as an additional energy and/or amino-acid source, thus reducing the glucose demand for biomass growth during the hydrogen production process.     

Computational kinetic studies of pyruvate metabolism in Carboxydothermus hydrogenoformans Z-2901 for improved hydrogen production

Hydrogen is considered as a renewable energy source and it is also regarded as future fuel. Currently, hydrogen production through a biotechnological approach is a research priority. Hydrogenogens, a microbial species, are of significant interest to researchers because of their ability to produce biological hydrogen. Carboxydothermus hydrogenoformans Z-2901 is one among the hydrogenogens that can grow anaerobically by utilizing pyruvate as a carbon source, and can produce molecular hydrogen. In the present study, we performed an in silico kinetic simulation using the available Kyoto Encyclopedia of Genes and Genomes (KEGG) model and reconstructed pyruvate metabolism in C. hydrogenoformans Z-2901. During this metabolism, dissimilation of pyruvate leads to the formation of energy co-factors, such as ATP and NAD⁺/ NADH, and the level of these co-factors influences the specific growth rate of organism and hydrogen production. Our strategy for improving hydrogen production involves maximizing the ATP and NAD⁺ yield by modification of kinetic properties and adding new reactions in pyruvate metabolism through metabolic pathway reconstruction. Moreover, the influence of phosphoenol pyruvate carboxylase and pyruvate dehydrogenase enzyme concentration on cofactor productions was also simulated. The theoretical molar yield of ATP and NAD⁺ were obtained as 2.32 and 1.83 mM, respectively, from 1 mM/mg of phosphoenol pyruvate (PEP) utilization. A higher yield of ATP is achieved when the PEP level reaches 5 mM/mg. This work also suggests that PEP can be considered as an alternative substrate. In conclusion, the simulation results reported in this paper can be applied to design and evaluate strategies of strain construction for optimal hydrogen yield in C. hydrogenoformans.     

Reduction of chromate by fixed films of sulfate-reducing bacteria using hydrogen as an electron source

The ability of sulfate-reducing bacteria (SRB) to reduce chromate, Cr(VI), was evaluated using fixed-film growth systems and H₂ as the electron source. A main objective of the experiment was to distinguish between direct enzymatic reduction and indirect reduction by hydrogen sulfide, in order to subsequently verify and control the synergy of these two mechanisms. In batch experiments with the sulfate-reducing consortium CH10 selected from a mining site, 50 mg l⁻¹ Cr(VI) was reduced in 15 min in the presence of 500 mg l⁻¹ hydrogen sulfide compared to 16 mg l⁻¹ reduced in 1 h without hydrogen sulfide. Fixed films of a CH10 population and Desulfomicrobium norvegicum were fed-batch grown in a column bioreactor. After development of the biofilm, hydrogen sulfide was removed and the column was fed continuously with a 13-mg l⁻¹ Cr(VI) solution. Specific Cr(VI) reduction rates on pozzolana were close to 90 mg Cr(VI) h⁻¹ per gram of protein. Exposure to Cr(VI) had a negative effect on the subsequent ability of CH10 to reduce sulfate, but the inhibited bacteria remained viable. Journal of Industrial Microbiology & Biotechnology (2002) 28, 154–159 DOI: 10.1038/sj/jim/7000226 Received 20 September 2000/ Accepted in revised form 13 November 2001     

Rational redesign of the ferredoxin-NADP+-oxido-reductase/ferredoxin-interaction for photosynthesis-dependent H2-production

Utilization of electrons from the photosynthetic water splitting reaction for the generation of biofuels, commodities as well as application in biotransformations requires a partial rerouting of the photosynthetic electron transport chain. Due to its rather negative redox potential and its bifurcational function, ferredoxin at the acceptor side of Photosystem 1 is one of the focal points for such an engineering. With hydrogen production as model system, we show here the impact and potential of redox partner design involving ferredoxin (Fd), ferredoxin-oxido-reductase (FNR) and [FeFe]?hydrogenase HydA1 on electron transport in a future cyanobacterial design cell of Synechocystis PCC 6803. X-ray-structure-based rational design and the allocation of specific interaction residues by NMR-analysis led to the construction of Fd- and FNR-mutants, which in appropriate combination enabled an about 18-fold enhanced electron flow from Fd to HydA1 (in competition with equimolar amounts of FNR) in in vitro assays. The negative impact of these mutations on the Fd-FNR electron transport which indirectly facilitates H₂ production (with a contribution of ≤42% by FNR variants and ≤23% by Fd-variants) and the direct positive impact on the Fd-HydA1 electron transport (≤23% by Fd-mutants) provide an excellent basis for the construction of a hydrogen-producing design cell and the study of photosynthetic efficiency-optimization with cyanobacteria.     

External alternative NADH dehydrogenase of Saccharomyces cerevisiae: a potential source of superoxide

Three rotenone-insensitive NADH dehydrogenases are present in the mitochondria of yeast Saccharomyces cerevisiae, which lack complex I. To elucidate the functions of these enzymes, superoxide production was determined in yeast mitochondria. The low levels of hydrogen peroxide (0.10 to 0.18 nmol/min/mg) produced in mitochondria incubated with succinate, malate, or NADH were stimulated 9-fold by antimycin A. Myxothiazol and stigmatellin blocked completely hydrogen peroxide formation with succinate or malate, indicating that the cytochrome bc(1) complex is the source of superoxide; however, these inhibitors only inhibited 46% hydrogen peroxide formation with NADH as substrate. Diphenyliodonium inhibited hydrogen peroxide formation (with NADH as substrate) by 64%. Superoxide formation, determined by EPR and acetylated cytochrome c reduction in mitochondria was stimulated by antimycin A, and partially inhibited by myxothiazol and stigmatellin. Proteinase K digestion of mitoplasts reduced 95% NADH dehydrogenase activity with a similar inhibition of superoxide production. Mild detergent treatment of the proteinase-treated mitoplasts resulted in an increase in NADH dehydrogenase activity due to the oxidation of exogenous NADH by the internal NADH dehydrogenase; however, little increase in superoxide production was observed. These results suggest that the external NADH dehydrogenase is a potential source of superoxide in S. cerevisiae mitochondria.     

Oxidation of zeaxanthin: Isolation and properties of 3-hydroxyretinene

1. Anthers of Delonix regia flowers are a rich source of zeaxanthin. 2. Oxidation of zeaxanthin with hydrogen peroxide in the presence of osmium tetroxide results in the formation of 3-hydroxyretinene as one of the products. 3. 3-Hydroxyretinene gives 3-acetoxyretinene with acetic anhydride, and an oxime with hydroxylamine hydrochloride. 4. Reduction of 3-hydroxyretinene with sodium borohydride yields 3-hydroxyvitamin A. 5. Treatment of 3-hydroxyvitamin A with dry ethanolic hydrogen chloride results in the formation of 3-ethoxyanhydrovitamin A (anhydrovitamin A₂) and a compound that resembles naturally occurring anhydrovitamin A₂.     

Funding source and research report quality in nutrition practice-related research

Background

The source of funding is one of many possible causes of bias in scientific research. One method of detecting potential for bias is to evaluate the quality of research reports. Research exploring the relationship between funding source and nutrition-related research report quality is limited and in other disciplines the findings are mixed.

Objective

The purpose of this study is to determine whether types of funding sources of nutrition research are associated with differences in research report quality.

Design

A retrospective study of research reporting quality, research design and funding source was conducted on 2539 peer reviewed research articles from the American Dietetic Association''s Evidence Analysis Library® database.

Results

Quality rating frequency distributions indicate 43.3% of research reports were rated as positive, 50.1% neutral, and 6.6% as negative. Multinomial logistic regression results showed that while both funding source and type of research design are significant predictors of quality ratings (χ2 = 118.99, p<0.001), the model''s usefulness in predicting overall research report quality is little better than chance. Compared to research reports with government funding, those not acknowledging any funding sources, followed by studies with University/hospital funding were more likely to receive neutral vs positive quality ratings, OR = 1.85, P <0.001 and OR = 1.54, P<0.001, respectively and those that did not report funding were more likely to receive negative quality ratings (OR = 4.97, P<0.001). After controlling for research design, industry funded research reports were no more likely to receive a neutral or negative quality rating than those funded by government sources.

Conclusion

Research report quality cannot be accurately predicted from the funding source after controlling for research design. Continued vigilance to evaluate the quality of all research regardless of the funding source and to further understand other factors that affect quality ratings are warranted.     

木糖发酵产氢菌的筛选及其生长产氢特性研究

利用改进的Hungate厌氧技术, 从牛粪堆肥中分离出一株能有效利用木糖发酵产氢的中温菌HR-1。通过16S rRNA系统发育树分析表明, 菌株 HR-1 与丙酮丁醇梭菌Clostridium acetobutylicum ATCC 824 相似性最高为96%, 结合生理生化和生长特性分析表明, HR-1是梭菌属Clostridium的一个新种, 命名为Clostridium sp. HR-1。菌株HR-1为单胞生长的规则杆状菌(0.3 mm ~0.6 mm)×(1.4 mm~2.3 mm), 革兰氏染色为阴性, 无荚膜、无鞭毛、表面光滑、无明显凸起, 专性厌氧菌。HR-1可在10°C~45°C, pH 4.0~10.0条件下生长; 37°C和pH 8.0分别为其最适生长条件。发酵PYG的主要发酵产物有氢气、二氧化碳、乙酸、丁酸及少量乙醇。HR-1可以利用有机氮源和无机氮源生长并产氢, 酵母提取物是其最佳产氢氮源。HR-1在木糖浓度为3 g/L和初始pH 6.5条件下, 其比产氢量为1.84 mol-H2/mol-木糖, 最大比产氢速率为10.52 mmol H2/h·g-细胞干重。HR-1可以亦利用葡萄糖、半乳糖、纤维二糖、甘露糖和果糖等碳源生长并发酵产氢, 发酵葡萄糖时比产氢量为2.36 mol-H2/mol-葡萄糖。     

A new single-end mainstream CO2 capnograph

Most of the current mainstream respiratory devices for monitoring CO₂ concentration use the two-end structure combined with both reference-end and main testing-end. In this paper, we design a new single-end mainstream device for monitoring the carbon dioxide concentration that is breathed out of the human body. In this single end design, only the main testing-end will be involved. The mechanism is based on the low-cost digital processing method of blind source separation, which is used to separate the signal and then extract the reference signal. Meanwhile, in order to decrease the negative influence of device noise and the low sample precision caused by temperature drift, two steps are taken: one is wavelet denoising and the other is temperature drift compensation. These two steps are proved valid by clinical trials, thus improving the accuracy of devices.     

Optimization of nutrients for gellan gum production by Sphingomonas paucimobilis ATCC-31461 in molasses based medium using response surface methodology

A molasses based medium for the production of gellan by Sphingomonas paucimobilis ATCC-31461 was developed. Placket-Burman design criterion was applied to study the effect of various nutrient supplements on gellan production using molasses. Among the 20 variables tested, molasses, tryptone, casaminoacid, disodium hydrogen orthophosphate and manganese chloride showed significant effect on gellan production. A central composite design was applied to determine the optimum concentrations of the significant variables obtained from Placket-Burman design. Most suitable medium composition for production of gellan was (g/l): molasses-112.5; tryptone-1; casaminoacid-1; disodium hydrogen orthophosphate-1; manganese chloride-0.947 and the optimum gellan production was 13.814 g/l.     

Determination of the redox potential and diffusion coefficient of the protein plastocyanin using optically transparent filar electrodes

Direct and mediated electrolysis of the protein plastocyanin at a gold filar electrode is described. The filar electrode used is of a unique design that allows potentiometric measurements, steady-state voltammetry and absorption spectrophotometry to be performed on a few microliters of solution containing 0.1–1.0 mM protein. As a result, we have determined the formal potential and diffusion coefficient of the blue copper protein, plastocyanin, to be 372 ± 5 mV vs. normal hydrogen electrode and 8.9 · 10⁻⁷ cm² · s⁻¹, respectively. The same value of the formal potential is obtained from a steady-state current experiment, an equilibrium spectrophotometric experiment, and a twin-electrode steady-state spectrophotometric experiment. The fact that the diffusion coefficient is measured under conditions of steady-state current, results in significant improvement in signal to background over techniques that monitor a transient current, while the potential is changing.     

Transcranial Extracellular Impedance Control (tEIC) Modulates Behavioral Performances

Electric brain stimulations such as transcranial direct current stimulation (tDCS), transcranial random noise stimulation (tRNS), and transcranial alternating current stimulation (tACS) electrophysiologically modulate brain activity and as a result sometimes modulate behavioral performances. These stimulations can be viewed from an engineering standpoint as involving an artificial electric source (DC, noise, or AC) attached to an impedance branch of a distributed parameter circuit. The distributed parameter circuit is an approximation of the brain and includes electric sources (neurons) and impedances (volume conductors). Such a brain model is linear, as is often the case with the electroencephalogram (EEG) forward model. Thus, the above-mentioned current stimulations change the current distribution in the brain depending on the locations of the electric sources in the brain. Now, if the attached artificial electric source were to be replaced with a resistor, or even a negative resistor, the resistor would also change the current distribution in the brain. In light of the superposition theorem, which holds for any linear electric circuit, attaching an electric source is different from attaching a resistor; the resistor affects each active electric source in the brain so as to increase (or decrease in some cases of a negative resistor) the current flowing out from each source. From an electrophysiological standpoint, the attached resistor can only control the extracellular impedance and never causes forced stimulation; we call this technique transcranial extracellular impedance control (tEIC). We conducted a behavioral experiment to evaluate tEIC and found evidence that it had real-time enhancement and depression effects on EEGs and a real-time facilitation effect on reaction times. Thus, tEIC could be another technique to modulate behavioral performance.     

Amide temperature coefficients in the protein G B1 domain

Temperature coefficients have been measured for backbone amide ¹H and ¹⁵N nuclei in the B1 domain of protein G (GB1), using temperatures in the range 283–313 K, and pH values from 2.0 to 9.0. Many nuclei display pH-dependent coefficients, which were fitted to one or two pK_a values. ¹H coefficients showed the expected behaviour, in that hydrogen-bonded amides have less negative values, but for those amides involved in strong hydrogen bonds in regular secondary structure there is a negative correlation between strength of hydrogen bond and size of temperature coefficient. The best correlation to temperature coefficient is with secondary shift, indicative of a very approximately uniform thermal expansion. The largest pH-dependent changes in coefficient are for amides in loops adjacent to sidechain hydrogen bonds rather than the amides involved directly in hydrogen bonds, indicating that the biggest determinant of the temperature coefficient is temperature-dependent loss of structure, not hydrogen bonding. Amide ¹⁵N coefficients have no clear relationship with structure.     

Fermentative degradation of glyoxylate by a new strictly anaerobic bacterium

A new strictly anaerobic, gram-negative, nonsporeforming bacterium, Strain PerGlx1, was enriched and isolated from marine sediment samples with glyoxylate as sole carbon and energy source. The guanineplus-cytosine content of the DNA was 44.1±0.2 mol %. Glyoxylate was utilized as the only substrate and was stoichiometrically degraded to carbon dioxide, hydrogen, and glycolate. An acetyl-CoA and ADP-dependent glyoxylate converting enzyme activity, malic enzyme, and pyruvate synthase were found at activities sufficient for growth (0.25 U x mg protein^-1). These findings allow to design a new degradation pathway for glyoxylate: glyoxylate is condensed with acetyl-CoA to form malyl-CoA; the free energy of the thioester linkage in malyl-CoA is conserved by substrate level phosphorylation. Part of the electrons released during glyoxylate oxidation to CO₂ reduce a small fraction of glyoxylate to glycolate.     

Optical rotatory dispersion of mucopolysaccharides and mucopolysaccharide--dye complexes. II. Ultraviolet cotton effects in the amide transition bands

Ultraviolet optical rotatory dispersion curves of mucopolysaccharides exhibit particular Cotton effects in the spectral region of the n–π and π–π amide transitions. Two general patterns emerge: (1) enhancement of negative rotation and of the first negative Cotton effect (troughs 217–220 mμ) and (2) relative dominance of the positive Cotton effect in the π–π transition region (peak ～198 mμ). Groups (1) and (2) can be correlated with a structural difference in the linkages of the amino sugars: (1) occurs with polymers containing 3-1-linked glycosamino sugars and (2) with glycosamino moieties linked 4–1 by either α- or β-glycosidie bonds. Measurements of the circular dichroic absorption bands support the qualitative conclusions from optical rotation. All mucopolysaccharides exhibit a first, negative band centered at 208–211 mμ, while only those in group (2) show, in addition, a positive band centered at 189–192 mμ. A suggested unifying model considers that difference in kind and/or degree of preferred geometry of the amide groups obtains from two forms of secondary order: (1) having a linear hydrogen bond from the N (acceptor) to the (C₂)O—H of the preceding uronic acid and (2) having a linear hydrogen bond from the N (acceptor) to the (C₂ or ₃) O—H of the following sugar. The hydrogen bonds would have similar strength but opposite directions in two systems towards the nonreducing end (1) or towards the reducing end (2)], closing eight-membered rings      

(040)‐Crystal Facet Engineering of BiVO4 Plate Photoanodes for Solar Fuel Production

A (040)‐crystal facet engineered BiVO₄ ((040)‐BVO) photoanode is investigated for solar fuel production. The (040)‐BVO photoanode is favorable for improved charge carrier mobility and high photocatalytic active sites for solar light energy conversion. This crystal facet design of the (040)‐BVO photoanode leads to an increase in the energy conversion efficiency for solar fuel production and an enhancement of the oxygen evolution rate. The photocurrent density of the (040)‐BVO photoanode is determined to be 0.94 mA cm^?2 under AM 1.5 G illumination and produces 42.1% of the absorbed photon‐to‐current conversion efficiency at 1.23 V (vs RHE, reversible hydrogen electrode). The enhanced charge separation efficiency and improved charge injection efficiency driven by (040) facet can produce hydrogen with 0.02 mmol h^?1 at 1.23 V. The correlation between the (040)‐BVO photoanode and the solar fuel production is investigated. The results provide a promising approach for the development of solar fuel production using a BiVO₄ photoanode.     

Efficient Water Splitting Using a Simple Ni/N/C Paper Electrocatalyst

An efficient water splitting electrocatalyst is presented. Cheap and sustainable cellulose filter paper, infiltrated with nickel acetate as the nickel source, and phenanthroline as a ligand and nitrogen source are carbonized together. Nitrogen functionalities turn out to be crucial coordination sites for the supported Ni/NiO(OH) particles. This simple and scalable one step procedure leads to powders, but also to complete membranes made of ≈10 wt% Ni, supported on nitrogen functionalized carbon. The non‐noble catalyst shows a low onset potential (330 mV vs reversible hydrogen electrode), high current density (e.g., j > 25 mA cm^?­2 at η = 430 mV), excellent kinetics (Tafel slope of 44 mV dec^?1), and a very favorable stability (<5% decay after 10 h electrolysis) in the oxygen evolution. The performance is similar or even better compared to state‐of‐the‐art noble metal catalysts (e.g., IrO₂, Ir/C, Ru/C, and Pt/C). Because of the simple, cheap, and scalable preparation procedure the catalyst is highly promising for practical low price/tech applications. Interestingly, the system is also active in the hydrogen evolution reaction, leading to a promising bifunctional catalyst. The benchmark characteristics are η₁₀ = 390 mV for oxygen evolution and η₁₀ = 190 mV for hydrogen evolution, that is, an overall efficiency of 68% at 10 mA current density.     

Microbial Utilization of Electrically Reduced Neutral Red as the Sole Electron Donor for Growth and Metabolite Production

Electrically reduced neutral red (NR) served as the sole source of reducing power for growth and metabolism of pure and mixed cultures of H₂-consuming bacteria in a novel electrochemical bioreactor system. NR was continuously reduced by the cathodic potential (−1.5 V) generated from an electric current (0.3 to 1.0 mA), and it was subsequently oxidized by Actinobacillus succinogenes or by mixed methanogenic cultures. The A. succinogenes mutant strain FZ-6 did not grow on fumarate alone unless electrically reduced NR or hydrogen was present as the electron donor for succinate production. The mutant strain, unlike the wild type, lacked pyruvate formate lyase and formate dehydrogenase. Electrically reduced NR also replaced hydrogen as the sole electron donor source for growth and production of methane from CO₂. These results show that both pure and mixed cultures can function as electrochemical devices when electrically generated reducing power can be used to drive metabolism. The potential utility of utilizing electrical reducing power in enhancing industrial fermentations or biotransformation processes is discussed.