Porphyrin‐Derived Graphene‐Based Nanosheets Enabling Strong Polysulfide Chemisorption and Rapid Kinetics in Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries hold great promise as a next‐generation battery system because of their extremely high theoretical energy density and low cost. However, ready lithium polysulfide (LiPS) diffusion and sluggish redox kinetics hamper their cyclability and rate capability. Herein, porphyrin‐derived graphene‐based nanosheets (PNG) are proposed for Li–S batteries, which are achieved by pyrolyzing a conformal and thin layer of 2D porphyrin organic framework on graphene to form carbon nanosheets with a spatially engineered nitrogen‐dopant‐enriched skin and a highly conductive skeleton. The atomic skin is decorated with fully exposed lithiophilic sites to afford strong chemisorption to LiPSs and improve electrolyte wettability, while graphene substrate provides speedy electron transport to facilitate redox kinetics of sulfur species. The use of PNG as a lightweight interlayer enables efficient operation of Li–S batteries in terms of superb cycle stability (cyclic decay rate of 0.099% during 300 cycles at 0.5 C), good rate capability (988 mAh g^?1 at 2.0 C), and impressive sulfur loading (areal capacity of 8.81 mAh cm^?2 at a sulfur loading of 8.9 mg cm^?2). The distinct interfacial strategy is expected to apply to other conversion reaction batteries relying on dissolution–precipitation mechanisms and requiring interfacial charge‐ and mass‐transport‐mediation concurrently.     

Sandwich‐Like Ultrathin TiS2 Nanosheets Confined within N,S Codoped Porous Carbon as an Effective Polysulfide Promoter in Lithium‐Sulfur Batteries

As the lightest member of transition metal dichalcogenides, 2D titanium disulfide (2D TiS₂) nanosheets are attractive for energy storage and conversion. However, reliable and controllable synthesis of single‐ to few‐layered TiS₂ nanosheets is challenging due to the strong tendency of stacking and oxidation of ultrathin TiS₂ nanosheets. This study reports for the first time the successful conversion of Ti₃C₂T_x MXene to sandwich‐like ultrathin TiS₂ nanosheets confined by N, S co‐doped porous carbon (TiS₂@NSC) via an in situ polydopamine‐assisted sulfuration process. When used as a sulfur host in lithium–sulfur batteries, TiS₂@NSC shows both high trapping capability for lithium polysulfides (LiPSs), and remarkable electrocatalytic activity for LiPSs reduction and lithium sulfide oxidation. A freestanding sulfur cathode integrating TiS₂@NSC with cotton‐derived carbon fibers delivers a high areal capacity of 5.9 mAh cm^?2 after 100 cycles at 0.1 C with a low electrolyte/sulfur ratio and a high sulfur loading of 7.7 mg cm^?2, placing TiS₂@NSC one of the best LiPSs adsorbents and sulfur conversion catalysts reported to date. The developed nanospace‐confined strategy will shed light on the rational design and structural engineering of metal sulfides based nanoarchitectures for diverse applications.     

Metal Sulfide‐Decorated Carbon Sponge as a Highly Efficient Electrocatalyst and Absorbant for Polysulfide in High‐Loading Li2S Batteries

Owing to its high theoretical specific capacity (1166 mA h g^?1) and particularly its advantage to be paired with a lithium‐metal‐free anode, lithium sulfide (Li₂S) is regarded as a much safer cathode for next‐generation advanced lithium–sulfur (Li–S) batteries. However, the low conductivity of Li₂S and particularly the severe “polysulfide shuttle” of lithium polysulfide (LiPS) dramatically hinder their practical application in Li–S batteries. To address such issues, herein a bifuctional 3D metal sulfide‐decorated carbon sponge (3DTSC), which is constructed by 1D carbon nanowires cross‐linked with 2D graphene nanosheets with high conductivity and polar 0D metal sulfide nanodots with efficient electrocatalytic activity and strong chemical adsorption capability for LiPSs, is presented. Benefiting from the well‐designed multiscale, multidimensional 3D porous nanoarchitecture with high conductivity, and efficient electrocatalytic and absorption ability, the 3DTSC significantly mitigates LiPS shuttle, improves the utilization of Li₂S, and facilitates the transport of electrons and ions. As a result, even with a high Li₂S loading of 8 mg cm^?2, the freestanding 3DTSC‐Li₂S cathode without a polymer binder and metallic current collector delivers outstanding electrochemical performance with a high areal capacity of 8.44 mA h cm^?2.     

Electrochemically Stable Rechargeable Lithium–Sulfur Batteries with a Microporous Carbon Nanofiber Filter for Polysulfide

As a primary component in lithium–sulfur (Li–S) batteries, the separator may require a custom design in order to facilitate electrochemical stability and reversibility. Here, a custom separator with an activated carbon nanofiber (ACNF)‐filter coated onto a polypropylene membrane is presented. The entire configuration is comprised of the ACNF filter arranged adjacent to the sulfur cathode so that it can filter out the freely migrating polysulfides and suppress the severe polysulfide diffusion. Four differently optimized ACNF‐filter‐coated separators have been developed with tunable micropores as an investigation into the electrochemical and engineering design parameters of functionalized separators. The optimized parameters that are verified by electrochemical and microstructural analyses require the coated ACNF filter to possess the following: (i) a porous architecture with abundant micropores, (ii) small micropore sizes, and (iii) high electrical conductivity and effective electrolyte immersion. It is found that the ACNF20‐filter‐coated separator demonstrates an overall superior boost in the electrochemical utilization (discharge capacity: 1270 mA h g^?1) and polysulfide retention (capacity fade rate: 0.13% cycle^?1 after 200 cycles). These results show that the modified thin‐film‐coating technique is a viable approach to designing ultratough ACNF‐filter‐coated separators with outstanding mechanical strength and flexibility as an advanced component in Li–S cells.     

Fabrication of N‐doped Graphene–Carbon Nanotube Hybrids from Prussian Blue for Lithium–Sulfur Batteries

Hybrid nanostructures containing 1D carbon nanotubes and 2D graphene sheets have many promising applications due to their unique physical and chemical properties. In this study, the authors find Prussian blue (dehydrated sodium ferrocyanide) can be converted to N‐doped graphene–carbon nanotube hybrid materials through a simple one‐step pyrolysis process. Through field emission scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, Raman spectra, atomic force microscopy, and isothermal analyses, the authors identify that 2D graphene and 1D carbon nanotubes are bonded seamlessly during the growth stage. When used as the sulfur scaffold for lithium–sulfur batteries, it demonstrates outstanding electrochemical performance, including a high reversible capacity (1221 mA h g^?1 at 0.2 C rate), excellent rate capability (458 and 220 mA h g^?1 at 5 and 10 C rates, respectively), and excellent cycling stability (321 and 164 mA h g^?1 at 5 and 10 C (1 C = 1673 mA g^?1) after 1000 cycles). The enhancement of electrochemical performance can be attributed to the 3D architecture of the hybrid material, in which, additionally, the nitrogen doping generates defects and active sites for improved interfacial adsorption. Furthermore, the nitrogen doping enables the effective trapping of lithium polysulfides on electroactive sites within the cathode, leading to a much‐improved cycling performance. Therefore, the hybrid material functions as a redox shuttle to catenate and bind polysulfides, and convert them to insoluble lithium sulfide during reduction. The strategy reported in this paper could open a new avenue for low cost synthesis of N‐doped graphene–carbon nanotube hybrid materials for high performance lithium–sulfur batteries.     

Highly Stable Lithium–Sulfur Batteries Based on Laponite Nanosheet‐Coated Celgard Separators

Lithium–sulfur (Li–S) batteries are of great interest due to their high theoretical energy density. However, one of the key issues hindering their real world applications is polysulfide shuttle, which results in severe capacity decay and self‐discharge. Here, a laponite nanosheets/carbon black coated Celgard (LNS/CB‐Celgard) separator to inhibit polysulfide shuttle and to enhance the Li⁺ conductivity simultaneously is reported. The polysulfide shuttle is efficiently inhibited through strong interactions between the O active sites of the LNS and polysulfides by forming the Li···O and O? S bonds. Moreover, the separator features high Li⁺ conductivity, fast Li⁺ diffusion, excellent electrolyte wettability, and high thermal stability. Consequently, the Li–S batteries with the LNS/CB‐Celgard separator and the pure S cathode show a high initial reversible capacity of 1387 mA h g^?1 at 0.1 C, high rate performance, superior cycling stability (with a capacity decay rate of 0.06% cycle^?1 at 0.2 C and 0.028% cycle^?1 at 1.0 C over 500 cycles), and ultralow self‐discharge. The separator could also enhance the performance of other batteries such as the LiFePO₄/separator/Li battery. This work sheds a new light on the design and preparation of novel separators for highly stable Li–S batteries via a “green” and cost‐effective approach.     

1T′‐ReS2 Nanosheets In Situ Grown on Carbon Nanotubes as a Highly Efficient Polysulfide Electrocatalyst for Stable Li–S Batteries

The practical viability of Li–S cells depends on achieving high electrochemical utilization of sulfur under realistic conditions, such as high sulfur loading and low electrolyte/sulfur (E/S) ratio. Here, metallic 2D 1T′‐ReS₂ nanosheets in situ grown on 1D carbon nanotubes (ReS₂@CNT) via a facile hydrothermal reaction are presented to efficiently suppress the “polysulfide shuttle” and promote lithium polysulfide (LiPS) redox reactions. The designed ReS₂@CNT nanoarchitecture with high conductivity and rich nanoporosity not only facilitates electron transfer and ion diffusion, but also possesses abundant active sites providing high catalytic activity for efficient LiPS conversion. Li–S cells fabricated with ReS₂@CNT exhibit high capacity with superior long‐term cyclability with a capacity retention of 71.7% over 1000 cycles even at a high current density of 1C (1675 mA g^?1). Also, pouch cells fabricated with the ReS₂@CNT/S cathode maintain a low capacity fade rate of 0.22% per cycle. Furthermore, the electrocatalysis mechanism is revealed based on electrochemical studies, theoretical calculations, and in situ Raman spectroscopy.     

Long‐Life,High‐Rate Lithium–Sulfur Cells with a Carbon‐Free VN Host as an Efficient Polysulfide Adsorbent and Lithium Dendrite Inhibitor

Lithium–sulfur (Li‐S) batteries are a promising next‐generation energy‐storage system, but the polysulfide shuttle and dendritic Li growth seriously hinder their commercial viability. Most of the previous studies have focused on only one of these two issues at a time. To address both the issues simultaneously, presented here is a highly conductive, noncarbon, 3D vanadium nitride (VN) nanowire array as an efficient host for both sulfur cathodes and lithium‐metal anodes. With fast electron and ion transport and high porosity and surface area, VN traps the soluble polysulfides, promotes the redox kinetics of sulfur cathodes, facilitates uniform nucleation/growth of lithium metal, and inhibits lithium dendrite growth at an unprecedented high current density of 10 mA cm^?2 over 200 h of repeated plating/stripping. As a result, VN‐Li||VN‐S full cells constructed with VN as both an anode and cathode host with a negative to positive electrode capacity ratio of only ≈2 deliver remarkable electrochemical performance with a high Coulombic efficiency of ≈99.6% over 850 cycles at a high 4 C rate and a high areal capacity of 4.6 mA h cm^?2. The strategy presented here offers a viable approach to realize high‐energy‐density, safe Li‐metal‐based batteries.     

New Lithium Salt Forms Interphases Suppressing Both Li Dendrite and Polysulfide Shuttling

Lithium–sulfur batteries (LSBs) are considered promising candidates for the next‐generation energy‐storage systems due to their high theoretical capacity and prevalent abundance of sulfur. Their reversible operation, however, encounters challenges from both the anode, where dendritic and dead Li‐metal form, and the cathode, where polysulfides dissolve and become parasitic shuttles. Both issues arise from the imperfection of interphases between electrolyte and electrode. Herein, a new lithium salt based on an imide anion with fluorination and unsaturation in its structure is reported, whose interphasial chemistries resolve these issues simultaneously. Lithium 1, 1, 2, 2, 3, 3‐hexafluoropropane‐1, 3‐disulfonimide (LiHFDF) forms highly fluorinated interphases at both anode and cathode surfaces, which effectively suppress formation of Li‐dendrites and dissolution/shuttling of polysulfides, and significantly improves the electrochemical reversibility of LSBs. In a broader context, this new Li salt offers a new perspective for diversified beyond Li‐ion chemistries that rely on a Li‐metal anode and active cathode materials.     

Trapping and Redistribution of Hydrophobic Sulfur Sols in Graphene–Polyethyleneimine Networks for Stable Li–S Cathodes

The lithium–sulfur battery is a promising next‐generation rechargeable battery system which promises to be less expensive and potentially fivefold more energy dense than current Li‐ion technologies. This can only be achieved by improving the sulfur utilization in thick, high areal loading cathodes while minimizing capacity fading to realize high practical energy densities and long cycle‐life. This study reports a simple method to fabricate a high capacity, high loading cathode with one of the highest cycle‐stabilities reported. It is demonstrated that sulfur sols formed by crashing dissolved elemental sulfur into water are trapped between graphene oxide sheets when flocculated with polyethyleneimine. Low temperature, hydrothermal treatment produces a conductive, partially covalent composite exhibiting outstanding cycle‐stability. Using this method, sulfur can be uniformly distributed at fractions as high as 75.7 wt%. Electrodes with high areal sulfur loadings (up to ≈5.4 mg cm^?2), prepared using these composites, lead to projected high cell level practical energy densities of 400 Wh kg^?1. The electrodes demonstrate negligible capacity loss over 250 cycles at 0.15 C and only 0.028% capacity loss per cycle over 810 cycles at 0.75 C. Eventual capacity fading is found to be linked to degradation of lithium‐metal anode suggesting that the cathode material remains stable over even more extended cycling.     

Designing Safe Electrolyte Systems for a High‐Stability Lithium–Sulfur Battery

Safety, nontoxicity, and durability directly determine the applicability of the essential characteristics of the lithium (Li)‐ion battery. Particularly, for the lithium–sulfur battery, due to the low ignition temperature of sulfur, metal lithium as the anode material, and the use of flammable organic electrolytes, addressing security problems is of increased difficulty. In the past few years, two basic electrolyte systems are studied extensively to solve the notorious safety issues. One system is the conventional organic liquid electrolyte, and the other is the inorganic solid‐state or quasi‐solid‐state composite electrolyte. Here, the recent development of engineered liquid electrolytes and design considerations for solid electrolytes in tackling these safety issues are reviewed to ensure the safety of electrolyte systems between sulfur cathode materials and the lithium‐metal anode. Specifically, strategies for designing and modifying liquid electrolytes including introducing gas evolution, flame, aqueous, and dendrite‐free electrolytes are proposed. Moreover, the considerations involving a high‐performance Li⁺ conductor, air‐stable Li⁺ conductors, and stable interface performance between the sulfur cathode and the lithium anode for developing all‐solid‐state electrolytes are discussed. In the end, an outlook for future directions to offer reliable electrolyte systems is presented for the development of commercially viable lithium–sulfur batteries.     

Ultrafine Co3Se4 Nanoparticles in Nitrogen‐Doped 3D Carbon Matrix for High‐Stable and Long‐Cycle‐Life Lithium Sulfur Batteries

Lithium–sulfur batteries are a promising high energy output solution for substitution of traditional lithium ion batteries. In recent times research in this field has stepped into the exploration of practical applications. However, their applications are impeded by cycling stability and short life‐span mainly due to the notorious polysulfide shuttle effect. In this work, a multifunctional sulfur host fabricated by grafting highly conductive Co₃Se₄ nanoparticles onto the surface of an N‐doped 3D carbon matrix to inhibit the polysulfide shuttle and improve the sulfur utilization is proposed. By regulating the carbon matrix and the Co₃Se₄ distribution, N‐CN‐750@Co₃Se₄‐0.1 m with abundant polar sites is experimentally and theoretically shown to be a good LiPSs absorbent and a sulfur conversion accelerator. The S/N‐CN‐750@Co₃Se₄‐0.1 m cathode shows excellent sulfur utilization, rate performance, and cyclic durability. A prolonged cycling test of the as‐fabricated S/N‐CN‐750@Co₃Se₄‐0.1 m cathode is carried out at 0.2 C for more than 5 months which delivers a high initial capacity of 1150.3 mAh g^?1 and retains 531.0 mAh g^?1 after 800 cycles with an ultralow capacity reduction of 0.067% per cycle, maintaining Coulombic efficiency of more than 99.3%. The reaction details are characterized and analyzed by ex situ measurements. This work highly emphasizes the potential capabilities of transition‐metal selenides in lithium–sulfur batteries.     

A Multifunctional Separator Enables Safe and Durable Lithium/Magnesium–Sulfur Batteries under Elevated Temperature

Rechargeable metal–sulfur batteries encounter severe safety hazards and fast capacity decay, caused by the flammable and shrinkable separator and unwanted polysulfide dissolution under elevated temperatures. Herein, a multifunctional Janus separator is designed by integrating temperature endurable electrospinning polyimide nonwovens with a copper nanowire‐graphene nanosheet functional layer and a rigid lithium lanthanum zirconium oxide‐polyethylene oxide matrix. Such architecture offers multifold advantages: i) intrinsically high dimensional stability and flame‐retardant capability, ii) excellent electrolyte wettability and effective metal dendritic growth inhibition, and iii) powerful physical blockage/chemical anchoring capability for the shuttled polysulfides. As a consequence, the as constructed lithium–sulfur battery using a pure sulfur cathode displays an outstandingly high discharge capacity of 1402.1 mAh g^?1 and a record high cycling stability (approximately average 0.24% capacity decay per cycle within 300 cycles) at 80 °C, outperforming the state‐of‐the‐art results in the literature. Promisingly, a high sulfur mass loading of ≈3.0 mg cm^?2 and a record low electrolyte/sulfur ratio of 6.0 are achieved. This functional separator also performs well for a high temperature magnesium–sulfur battery. This work demonstrates a new concept for high performance metal–sulfur battery design and promises safe and durable operation of the next generation energy storage systems.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Catalytic Polysulfide Conversion and Physiochemical Confinement for Lithium–Sulfur Batteries

The lithium–sulfur (Li–S) battery is widely regarded as a promising energy storage device due to its low price and the high earth‐abundance of the materials employed. However, the shuttle effect of lithium polysulfides (LiPSs) and sluggish redox conversion result in inefficient sulfur utilization, low power density, and rapid electrode deterioration. Herein, these challenges are addressed with two strategies 1) increasing LiPS conversion kinetics through catalysis, and 2) alleviating the shuttle effect by enhanced trapping and adsorption of LiPSs. These improvements are achieved by constructing double‐shelled hollow nanocages decorated with a cobalt nitride catalyst. The N‐doped hollow inner carbon shell not only serves as a physiochemical absorber for LiPSs, but also improves the electrical conductivity of the electrode; significantly suppressing shuttle effect. Cobalt nitride (Co₄N) nanoparticles, embedded in nitrogen‐doped carbon in the outer shell, catalyze the conversion of LiPSs, leading to decreased polarization and fast kinetics during cycling. Theoretical study of the Li intercalation energetics confirms the improved catalytic activity of the Co₄N compared to metallic Co catalyst. Altogether, the electrode shows large reversible capacity (1242 mAh g^?1 at 0.1 C), robust stability (capacity retention of 658 mAh g^?1 at 5 C after 400 cycles), and superior cycling stability at high sulfur loading (4.5 mg cm^?2).