Electrochemical Stability of Li10GeP2S12 and Li7La3Zr2O12 Solid Electrolytes

The electrochemical stability window of solid electrolyte is overestimated by the conventional experimental method using a Li/electrolyte/inert metal semiblocking electrode because of the limited contact area between solid electrolyte and inert metal. Since the battery is cycled in the overestimated stability window, the decomposition of the solid electrolyte at the interfaces occurs but has been ignored as a cause for high interfacial resistances in previous studies, limiting the performance improvement of the bulk‐type solid‐state battery despite the decades of research efforts. Thus, there is an urgent need to identify the intrinsic stability window of the solid electrolyte. The thermodynamic electrochemical stability window of solid electrolytes is calculated using first principles computation methods, and an experimental method is developed to measure the intrinsic electrochemical stability window of solid electrolytes using a Li/electrolyte/electrolyte‐carbon cell. The most promising solid electrolytes, Li₁₀GeP₂S₁₂ and cubic Li‐garnet Li₇La₃Zr₂O₁₂, are chosen as the model materials for sulfide and oxide solid electrolytes, respectively. The results provide valuable insights to address the most challenging problems of the interfacial stability and resistance in high‐performance solid‐state batteries.     

Perovskite Membranes with Vertically Aligned Microchannels for All‐Solid‐State Lithium Batteries

Perovskite‐type solid‐state electrolytes exhibit great potential for the development of all‐solid‐state lithium batteries due to their high Li‐ion conductivity (approaching 10^?3 S cm^?1), wide potential window, and excellent thermal/chemical stability. However, the large solid–solid interfacial resistance between perovskite electrolytes and electrode materials is still a great challenge that hinders the development of high‐performance all‐solid‐state lithium batteries. In this work, a perovskite‐type Li_0.34La_0.51TiO₃ (LLTO) membrane with vertically aligned microchannels is constructed by a phase‐inversion method. The 3D vertically aligned microchannel framework membrane enables more effective Li‐ion transport between the cathode and solid‐state electrolyte than a planar LLTO membrane. A significant decrease in the perovskite/cathode interfacial resistance, from 853 to 133 Ω cm², is observed. It is also demonstrated that full cells utilizing LLTO with vertically aligned microchannels as the electrolyte exhibit a high specific capacity and improved rate performance.     

A Flexible Solid‐State Aqueous Zinc Hybrid Battery with Flat and High‐Voltage Discharge Plateau

The migration of zinc‐ion batteries from alkaline electrolyte to neutral or mild acidic electrolyte promotes research into their flexible applications. However, discharge voltage of many reported zinc‐ion batteries is far from satisfactory. On one hand, the battery voltage is substantially restricted by the narrow voltage window of aqueous electrolytes. On the other hand, many batteries yield a low‐voltage discharge plateau or show no plateau but capacitor‐like sloping discharge profiles. This impacts the battery's practicability for flexible electronics where stable and consistent high energy is needed. Herein, an aqueous zinc hybrid battery based on a highly concentrated dual‐ion electrolyte and a hierarchically structured lithium‐ion‐intercalative LiVPO₄F cathode is developed. This hybrid battery delivers a flat and high‐voltage discharge plateau of nearly 1.9 V, ranking among the highest reported values for all aqueous zinc‐based batteries. The resultant high energy density of 235.6 Wh kg^?1 at a power density of 320.8 W kg^?1 also outperforms most reported zinc‐based batteries. A designed solid‐state and long‐lasting hydrogel electrolyte is subsequently applied in the fabrication of a flexible battery, which can be integrated into various flexible devices as powerful energy supply. The idea of designing such a hybrid battery offers a new strategy for developing high‐voltage and high‐energy aqueous energy storage systems.     

Electrolytes toward High‐Voltage Na3V2(PO4)2F3 Positive Electrode Durable against Temperature Variation

High power and energy density, long cyclability, and tolerance for wide temperature (seasonal and daily operational temperature differences) must be considered to construct large‐scale sodium secondary batteries. In this regard, Na₃V₂(PO₄)₂F₃ (NVPF) has become a subject of interest as a high‐performance positive electrode material owing to its high energy density. However, the high operating voltage of NVPF causes continuous decomposition of electrolytes during cycles, resulting in significant capacity fading and low Coulombic efficiency. In this study, the electrochemical performance of the NVPF electrode in organic solvent electrolytes with and without additives and an ionic liquid is investigated at high voltage regimes over a wide temperature range (?20 °C to 90 °C). The results reveal that the performance of organic electrolytes is still insufficient even with additives, and the ionic liquid electrolyte demonstrates high electrochemical stability and cyclability with NVPF electrodes over a temperature range from ?20 °C to 90 °C, achieving stable cycling over 500 cycles. The detailed electrochemical analysis combined with X‐ray photoelectron and energy dispersive X‐ray spectroscopy indicates that a sturdy cathode electrolyte interphase layer around the electrode protects it from capacity fading at high voltage and elevated temperature, resulting in high Coulombic efficiency.     

Stack Pressure Considerations for Room‐Temperature All‐Solid‐State Lithium Metal Batteries

All‐solid‐state batteries are expected to enable batteries with high energy density with the use of lithium metal anodes. Although solid electrolytes are believed to be mechanically strong enough to prevent lithium dendrites from propagating, various reports today still show cell failure due to lithium dendrit growth at room temperature. While cell parameters such as current density, electrolyte porosity, and interfacial properties have been investigated, mechanical properties of lithium metal and the role of applied stack pressure on the shorting behavior are still poorly understood. Here, failure mechanisms of lithium metal are investigated in all‐solid‐state batteries as a function of stack pressure, and in situ characterization of the interfacial and morphological properties of the buried lithium is conducted in solid electrolytes. It is found that a low stack pressure of 5 MPa allows reliable plating and stripping in a lithium symmetric cell for more than 1000 h, and a Li | Li₆PS₅Cl | LiNi_0.80Co_0.15Al_0.05O₂ full cell, plating more than 4 µm of lithium per charge, is able to cycle over 200 cycles at room temperature. These results suggest the possibility of enabling the lithium metal anode in all‐solid‐state batteries at reasonable stack pressures.     

A High Energy Density Aqueous Battery Achieved by Dual Dissolution/Deposition Reactions Separated in Acid‐Alkaline Electrolyte

Aqueous batteries are facing big challenges in the context of low working voltages and energy density, which are dictated by the narrow electrochemical window of aqueous electrolytes and low specific capacities of traditional intercalation‐type electrodes, even though they usually represent high safety, low cost, and simple maintenance. For the first time, this work demonstrates a record high‐energy‐density (1503 Wh kg^?1 calculated from the cathode active material) aqueous battery system that derives from a novel electrolyte design to expand the electrochemical window of electrolyte to 3 V and two high‐specific‐capacity electrode reactions. An acid‐alkaline dual electrolyte separated by an ion‐selective membrane enables two dissolution/deposition electrode redox reactions of MnO₂/Mn²⁺ and Zn/Zn(OH)₄^2? with theoretical specific capacities of 616 and 820 mAh g^?1, respectively. The newly proposed Zn–Mn²⁺ aqueous battery shows a high Coulombic efficiency of 98.4% and cycling stability of 97.5% of discharge capacity retention for 1500 cycles. Furthermore, in the flow battery based on Zn–Mn²⁺ pairs, more excellent stability of 99.5% of discharge capacity retention for 6000 cycles is achieved due to greatly improved reversibility of the Zn anode. This work provides a new path for the development of novel aqueous batteries with high voltage and energy density.     

Stable Seamless Interfaces and Rapid Ionic Conductivity of Ca–CeO2/LiTFSI/PEO Composite Electrolyte for High‐Rate and High‐Voltage All‐Solid‐State Battery

Stable and seamless interfaces among solid components in all‐solid‐state batteries (ASSBs) are crucial for high ionic conductivity and high rate performance. This can be achieved by the combination of functional inorganic material and flexible polymer solid electrolyte. In this work, a flexible all‐solid‐state composite electrolyte is synthesized based on oxygen‐vacancy‐rich Ca‐doped CeO₂ (Ca–CeO₂) nanotube, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), and poly(ethylene oxide) (PEO), namely Ca–CeO₂/LiTFSI/PEO. Ca–CeO₂ nanotubes play a key role in enhancing the ionic conductivity and mechanical strength while the PEO offers flexibility and assures the stable seamless contact between the solid electrolyte and the electrodes in ASSBs. The as‐prepared electrolyte exhibits high ionic conductivity of 1.3 × 10^?4 S cm^?1 at 60 °C, a high lithium ion transference number of 0.453, and high‐voltage stability. More importantly, various electrochemical characterizations and density functional theory (DFT) calculations reveal that Ca–CeO₂ helps dissociate LiTFSI, produce free Li ions, and therefore enhance ionic conductivity. The ASSBs based on the as‐prepared Ca–CeO₂/LiTFSI/PEO composite electrolyte deliver high‐rate capability and high‐voltage stability.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

High‐Performance Aqueous Rechargeable Li‐Ni Battery Based on Ni(OH)2/NiOOH Redox Couple with High Voltage

New energy storage and conversion systems require large‐scale, cost‐effective, good safety, high reliability, and high energy density. This study demonstrates a low‐cost and safe aqueous rechargeable lithium‐nickel (Li‐Ni) battery with solid state Ni(OH)₂/NiOOH redox couple as cathode and hybrid electrolytes separated by a Li‐ion‐conductive solid electrolyte layer. The proposed aqueous rechargeable Li‐Ni battery exhibits an approximately open‐circuit potential of 3.5 V, outperforming the theoretic stable window of water 1.23 V, and its energy density can be 912.6 W h kg^‐1, which is much higher than that of state‐of‐the‐art lithium ion batteries. The use of a solid‐state redox couple as cathode with a metallic lithium anode provides another postlithium chemistry for practical energy storage and conversion.     

Countersolvent Electrolytes for Lithium‐Metal Batteries

Development of electrolytes that simultaneously have high ionic conductivity, wide electrochemical window, and lithium dendrite suppression ability is urgently required for high‐energy lithium‐metal batteries (LMBs). Herein, an electrolyte is designed by adding a countersolvent into LiFSI/DMC (lithium bis(fluorosulfonyl)amide/dimethyl carbonate) electrolytes, forming countersolvent electrolytes, in which the countersolvent is immiscible with the salt but miscible with the carbonate solvents. The solvation structure and unique properties of the countersolvent electrolyte are investigated by combining electroanalytical technology with a Molecular Dynamics simulation. Introducing the countersolvent alters the coordination shell of Li⁺ cations and enhances the interaction between Li⁺ cations and FSI^? anions, which leads to the formation of a LiF‐rich solid electrolyte interphase, arising from the preferential reduction of FSI^? anions. Notably, the countersolvent electrolyte suppresses Li dendrites and enables stable cycling performance of a Li||NCM622 battery at a high cut‐off voltage of 4.6 V at both 25 and 60 °C. This study provides an avenue to understand and design electrolytes for high‐energy LMBs in the future.     

Solvent‐Free Synthesis of Thin,Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Thin solid‐state electrolytes with nonflammability, high ionic conductivity, low interfacial resistance, and good processability are urgently required for next‐generation safe, high energy density lithium metal batteries. Here, a 3D Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZTO) self‐supporting framework interconnected by polytetrafluoroethylene (PTFE) binder is prepared through a simple grinding method without any solvent. Subsequently, a garnet‐based composite electrolyte is achieved through filling the flexible 3D LLZTO framework with a succinonitrile solid electrolyte. Due to the high content of garnet ceramic (80.4 wt%) and high heat‐resistance of the PTFE binder, such a composite electrolyte film with nonflammability and high processability exhibits a wide electrochemical window of 4.8 V versus Li/Li⁺ and high ionic transference number of 0.53. The continuous Li⁺ transfer channels between interconnected LLZTO particles and succinonitrile, and the soft electrolyte/electrode interface jointly contribute to a high ambient‐temperature ionic conductivity of 1.2 × 10^?4 S cm^?1 and excellent long‐term stability of the Li symmetric battery (stable at a current density of 0.1 mA cm^?2 for over 500 h). Furthermore, as‐prepared LiFePO₄|Li and LiNi_0.5Mn_0.3Co_0.2O₂|Li batteries based on the thin composite electrolyte exhibit high discharge specific capacities of 153 and 158 mAh g^?1 respectively, and desirable cyclic stabilities at room temperature.     

Safety‐Reinforced Poly(Propylene Carbonate)‐Based All‐Solid‐State Polymer Electrolyte for Ambient‐Temperature Solid Polymer Lithium Batteries

An integrated preparation of safety‐reinforced poly(propylene carbonate)‐based all‐solid polymer electrolyte is shown to be applicable to ambient‐temperature solid polymer lithium batteries. In contrast to pristine poly(ethylene oxide) solid polymer electrolyte, this solid polymer electrolyte exhibits higher ionic conductivity, wider electrochemical window, better mechanical strength, and superior rate performance at 20 °C. Moreover, lithium iron phosphate/lithium cell using such solid polymer electrolyte can charge and discharge even at 120 °C. It is also noted that the solid‐state soft‐package lithium cells assembled with this solid polymer electrolyte can still power a red light‐emitting diode lamp without suffering from internal short‐circuit failures even after cutting off one part of the battery. Considering the aspects mentioned above, the solid polymer electrolyte is eligible for practical lithium battery applications with improved reliability and safety. Just as important, a new perspective that the degree of amorphous state of polymer is also as critical as its low glass transition temperature for the exploration of room temperature solid polymer electrolyte is illustrated. In all, this study opens up a kind of new avenue that could be a milestone to the development of high‐voltage and ambient‐temperature all‐solid‐state polymer electrolytes.     

Novel Sub‐5 nm Layered Niobium Phosphate Nanosheets for High‐Voltage,Cation‐Intercalation Typed Electrochemical Energy Storage in Wearable Pseudocapacitors

Layered niobium phosphates have been considered very promising energy storage materials because of their high theoretical operating voltage window and the rich oxidation states of niobium. However, their development has been stymied by the phase‐controlled synthesis due to the insolubility of niobium sources except in concentrated hydrofluoric (HF) acid systems. Herein, a new avenue is opened for layered acid niobium phosphate (2NbOPO₄·H₃PO₄·H₂O) synthesis in a mild oxalic acid system. Taking advantage of this strategy, in situ growth of sub‐5 nm 2NbOPO₄·H₃PO₄·H₂O nanosheet (NPene) arrays on conductive carbon fiber cloth (CFC) substrates is achieved as self‐standing electrodes for solid‐state supercapacitors. Interestingly, the NPene@CFC electrode exhibits a typical cation (H⁺ or Li⁺)‐intercalation kinetics with a wide potential window of 0–1.0 V in aqueous electrolytes. Given the wide potential window and highly exposed active surface, the solid‐state asymmetric supercapacitors constructed from such a NPenes@CFC electrode display a high working potential of 2.0 V, energy density of 122.2 W h kg^?1 at a power density of 589.7 W kg^?1, cycle stability with a capacitance retention of 94.2% after 10 000 cycles, and also outstanding flexible and wearable characteristics.     

Dopant‐Dependent Stability of Garnet Solid Electrolyte Interfaces with Lithium Metal

Li₇La₃Zr₂O₁₂ (LLZO) garnet‐based materials doped with Al, Nb, or Ta to stabilize the Li⁺‐conductive cubic phase are a particularly promising class of solid electrolytes for all‐solid‐state lithium metal batteries. Understanding of the intrinsic reactivity between solid electrolytes and relevant electrode materials is crucial to developing high voltage solid‐state batteries with long lifetimes. Using a novel, surface science‐based approach to characterize the intrinsic reactivity of the Li–solid electrolyte interface, it is determined that, surprisingly, some degree of Zr reduction takes place for all three dopant types, with the extent of reduction increasing as Ta < Nb < Al. Significant reduction of Nb also takes place for Nb‐doped LLZO, with electrochemical impedance spectroscopy (EIS) of Li||Nb–LLZO||Li symmetric cells further revealing significant increases in impedance with time and suggesting that the Nb reduction propagates into the bulk. Density functional theory (DFT) calculations reveal that Nb‐doped material shows a strong preference for Nb dopants toward the interface between LLZO and Li, while Ta does not exhibit a similar preference. EIS and DFT results, coupled with the observed reduction of Zr at the interface, are consistent with the formation of an “oxygen‐deficient interphase” (ODI) layer whose structure determines the stability of the LLZO–Li interface.     

Toward High Energy Density All Solid‐State Sodium Batteries with Excellent Flexibility

All solid‐state sodium batteries (ASSBs) have attracted considerable attention due to their enhanced safety, long lifespan, and high energy density. However, several challenges have plagued the development of ASSBs, especially the relatively low ionic conductivity of solid‐state electrolytes (SSEs), large interfacial resistance, and low stability/compatibility between SSEs and electrodes. Here, a high‐performance all solid‐state sodium battery (NVP@C|PEGDMA‐NaFSI‐SPE|Na) is designed by employing carbon coated Na₃V₂(PO₄)₃ composite nanosheets (NVP@C) as the cathode, solvent‐free solid polymer electrolyte (PEGDMA‐NaFSI‐SPE) as the electrolyte and metallic sodium as the anode. The integrated electrolyte and cathode system prepared by the in situ polymerization process exhibits high ionic conductivity (≈10^?4 S cm^?1 at room temperature) and an outstanding electrolyte/electrode interface. Benefiting from these merits, the soft‐pack ASSB (NVP@C|PEGDMA‐NaFSI‐SPE|Na) delivers excellent cycling life over 740 cycles (capacity decay of only 0.007% per cycle) and maintains 95% of the initial reversible capacity with almost no self‐discharge even after resting for 3 months. Moreover, the bendable ASSB exhibits a high capacity of 106 mAh g^?1 (corresponds to energy density of ≈355 Wh kg^?1) at 0.5 C despite undergoing repeated bending for 535 cycles. This work offers a new strategy to fabricate high‐performance flexible ASSBs with a long lifespan and excellent flexibility.     

Building Lithiophilic Ion‐Conduction Highways on Garnet‐Type Solid‐State Li+ Conductors

The integration of highly conductive solid‐state electrolytes (SSEs) into solid‐state cells is still a challenge mainly due to the high impedance existing at the electrolyte/electrode interface. Although solid‐state garnet‐based batteries have been successfully assembled with the assistance of an intermediate layer between the garnet and the Li metal anode, the slow discharging/charging rates of the batteries inhibits practical applications, which require much higher power densities. Here, a crystalline sulfonated‐covalent organic framework (COF) thin layer is grown on the garnet surface via a simple solution process. It not only significantly improves the lithiophilicity of garnet electrolytes via the lithiation of the COF layer with molten Li, but also creates effective Li⁺ diffusion “highways” between the garnet and the Li metal anode. As a result, the interfacial impedance of symmetric solid‐state Li cells is significantly decreased and the cells can be operated at high current densities up to 3 mA cm^?2, which is difficult to achieve with current interfacial modification technologies for SSEs. The solid‐state Li‐ion batteries using LiFePO₄ cathodes, Li anodes, and COF‐modified garnet electrolytes thus exhibit a significantly improved rate capability.     

A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

Sodium Plating from Na‐β″‐Alumina Ceramics at Room Temperature,Paving the Way for Fast‐Charging All‐Solid‐State Batteries

All‐solid‐state batteries with an alkali metal anode have the potential to achieve high energy density. However, the onset of dendrite formation limits the maximum plating current density across the solid electrolyte and prevents fast charging. It is shown that the maximum plating current density is related to the interfacial resistance between the solid electrolyte and the metal anode. Due to their high ionic conductivity, low electronic conductivity, and stability against sodium metal, Na‐β″‐alumina ceramics are excellent candidates as electrolytes for room‐temperature all‐solid‐state batteries. Here, it is demonstrated that a heat treatment of Na‐β″‐alumina ceramics in argon atmosphere enables an interfacial resistance <10 Ω cm² and current densities up to 12 mA cm^?2 at room temperature. The current density obtained for Na‐β″‐alumina is ten times higher than that measured on a garnet‐type Li₇La₃Zr₂O₁₂ electrolyte under equivalent conditions. X‐ray photoelectron spectroscopy shows that eliminating hydroxyl groups and carbon contaminations at the interface between Na‐β″‐alumina and sodium metal is key to reach such values. By comparing the temperature‐dependent stripping/plating behavior of Na‐β″‐alumina and Li₇La₃Zr₂O₁₂, the role of the alkali metal in governing interface kinetics is discussed. This study provides new insights into dendrite formation and paves the way for fast‐charging all‐solid‐state batteries.     

A Versatile Sn‐Substituted Argyrodite Sulfide Electrolyte for All‐Solid‐State Li Metal Batteries

Sulfide‐based solid‐state electrolytes (SSEs) for all‐solid‐state Li metal batteries (ASSLMBs) are attracting significant attention due to their high ionic conductivity, inherently soft properties, and decent mechanical strength. However, the poor incompatibility with Li metal and air sensitivity have hindered their application. Herein, the Sn (IV) substitution for P (V) in argyrodite sulfide Li₆PS₅I (LPSI) SSEs is reported, in the preparation of novel LPSI‐xSn SSEs (where x is the Sn substitution percentage). Appropriate aliovalent element substitutions with larger atomic radius (R_<Sn> > R_<P>) provides the optimized LPSI‐20Sn electrolyte with a 125 times higher ionic conductivity compared to that of the LPSI electrolyte. The high ionic conductivity of LPSI‐20Sn enables the rich I‐containing electrolyte to serve as a stabilized interlayer against Li metal in sulfide‐based ASSLMBs with outstanding cycling stability and rate capability. Most importantly, benefiting from the strong Sn–S bonding in Sn‐substituted electrolytes, the LPSI‐20Sn electrolyte shows excellent structural stability and improved air stability after exposure to O₂ and moisture. The versatile Sn substitution in argyrodite LPSI electrolytes is believed to provide a new and effective strategy to achieve Li metal‐compatible and air‐stable sulfide‐based SSEs for large‐scale applications.     

Reducing Mg Anode Overpotential via Ion Conductive Surface Layer Formation by Iodine Additive

Electrolytes that are able to reversibly deposit/strip Mg are crucial for rechargeable Mg batteries. The most studied complex electrolytes based on Lewis acid‐base chemistry are expensive, difficult to be synthesized, and show limited anodic stability. Conventional electrolytes using simple salts such as Mg(TFSI)₂ can be readily synthesized, but Mg deposition/stripping in these simple salt electrolytes is accompanied by a large overpotential due to the formation of a surface layer on the Mg metal with a low Mg ion conductivity. Here the overpotential for Mg deposition/stripping in a simple salt, Mg(TFSI)₂‐1,2‐dimethoxyethane (DME), electrolyte is significantly reduced by adding a small concentration of iodine (≤50 × 10^?3m ) as an additive. Mechanism studies demonstrate that an Mg ion conductive solid MgI₂ layer is formed on the surface of the Mg metal and acts as a solid electrolyte interface. With the Mg(TFSI)₂‐DME‐I₂ electrolyte, a very small voltage hysteresis is achieved in an Mg‐S full cell.