A Self‐Forming Composite Electrolyte for Solid‐State Sodium Battery with Ultralong Cycle Life

Replacing organic liquid electrolyte with inorganic solid electrolytes (SE) can potentially address the inherent safety problems in conventional rechargeable batteries. However, solid‐state batteries (SSBs) have been plagued by the relatively low ionic conductivity of SEs and large charge‐transfer resistance between electrode and SE. Here, a new design strategy is reported for improving the ionic conductivity of SE by self‐forming a composite material. An optimized Na⁺ ion conducting composite electrolyte derived from the Na_{1+ n} Zr₂Si _n P_{3? n} O₁₂ NASICON (Na Super Ionic Conductor) structure is successfully synthesized, yielding ultrahigh ionic conductivity of 3.4 mS cm^?1 at 25 °C and 14 mS cm^?1 at 80 °C. On the other hand, in order to enhance the charge‐transfer rate at the electrode/electrolyte interface, an interface modification strategy is demonstrated by utilization of a small amount of nonflammable and nonvolatile ionic liquid (IL) at the cathode side in SSBs. The IL acts as a wetting agent, enabling a favorable interface kinetic in SSBs. The Na₃V₂(PO₄)₃/IL/SE/Na SSB exhibits excellent cycle performance and rate capability. A specific capacity of ≈90 mA h g^?1 is maintained after 10 000 cycles without capacity decay under 10 C rate at room temperature. This provides a new perspective to design fast ion conductors and fabricate long life SSBs.     

Toward High Energy Density All Solid‐State Sodium Batteries with Excellent Flexibility

All solid‐state sodium batteries (ASSBs) have attracted considerable attention due to their enhanced safety, long lifespan, and high energy density. However, several challenges have plagued the development of ASSBs, especially the relatively low ionic conductivity of solid‐state electrolytes (SSEs), large interfacial resistance, and low stability/compatibility between SSEs and electrodes. Here, a high‐performance all solid‐state sodium battery (NVP@C|PEGDMA‐NaFSI‐SPE|Na) is designed by employing carbon coated Na₃V₂(PO₄)₃ composite nanosheets (NVP@C) as the cathode, solvent‐free solid polymer electrolyte (PEGDMA‐NaFSI‐SPE) as the electrolyte and metallic sodium as the anode. The integrated electrolyte and cathode system prepared by the in situ polymerization process exhibits high ionic conductivity (≈10^?4 S cm^?1 at room temperature) and an outstanding electrolyte/electrode interface. Benefiting from these merits, the soft‐pack ASSB (NVP@C|PEGDMA‐NaFSI‐SPE|Na) delivers excellent cycling life over 740 cycles (capacity decay of only 0.007% per cycle) and maintains 95% of the initial reversible capacity with almost no self‐discharge even after resting for 3 months. Moreover, the bendable ASSB exhibits a high capacity of 106 mAh g^?1 (corresponds to energy density of ≈355 Wh kg^?1) at 0.5 C despite undergoing repeated bending for 535 cycles. This work offers a new strategy to fabricate high‐performance flexible ASSBs with a long lifespan and excellent flexibility.     

A High‐Performance Monolithic Solid‐State Sodium Battery with Ca2+ Doped Na3Zr2Si2PO12 Electrolyte

Solid‐state sodium batteries (SSSBs) are promising electrochemical energy storage devices due to their high energy density, high safety, and abundant resource of sodium. However, low conductivity of solid electrolyte as well as high interfacial resistance between electrolyte and electrodes are two main challenges for practical application. To address these issues, pure phase Na₃Zr₂Si₂PO₁₂ (NZSP) materials with Ca²⁺ substitution for Zr⁴⁺ are synthesized by a sol‐gel method. It shows a high ionic conductivity of more than 10^?3 S cm^?1 at 25 °C. Moreover, a robust SSSB is developed by integrating sodium metal anodes into NZSP‐type monolithic architecture, forming a 3D electronic and ionic conducting network. The interfacial resistance is remarkably reduced and the monolithic symmetric cell displays stable sodium platting/striping cycles with low polarization for over 600 h. Furthermore, by combining sodium metal anode with Na₃V₂(PO₄)₃ cathode, an SSSB is demonstrated with high rate capability and excellent cyclability. After 450 cycles, the capacity of the cell is still kept at 94.9 mAh g^?1 at 1 C. This unique design of monolithic electrolyte architecture provides a promising strategy toward realizing high‐performance SSSBs.     

New Na‐Ion Solid Electrolytes Na4−xSn1−xSbxS4 (0.02 ≤ x ≤ 0.33) for All‐Solid‐State Na‐Ion Batteries

Sulfide Na‐ion solid electrolytes (SEs) are key to enable room‐temperature operable all‐solid‐state Na‐ion batteries that are attractive for large‐scale energy storage applications. To date, few sulfide Na‐ion SEs have been developed and most of the SEs developed contain P and suffer from poor chemical stability. Herein, discovery of a new structural class of tetragonal Na_4?xSn_1?xSb_xS₄ (0.02 ≤ x ≤ 0.33) with space group I4₁/acd is described. The evolution of a new phase, distinctly different from Na₄SnS₄ or Na₃SbS₄, allows fast ionic conduction in 3D pathways (0.2–0.5 mS cm^?1 at 30 °C). Moreover, their excellent air stability and reversible dissolution in water and precipitation are highlighted. Specifically, TiS₂/Na–Sn all‐solid‐state Na‐ion batteries using Na_3.75Sn_0.75Sb_0.25S₄ demonstrates high capacity (201 mA h (g of TiS₂)^?1) with excellent reversibility.     

Lithium‐Pretreated Hard Carbon as High‐Performance Sodium‐Ion Battery Anodes

Hard carbon (HC) is the state‐of‐the‐art anode material for sodium‐ion batteries (SIBs). However, its performance has been plagued by the limited initial Coulombic efficiency (ICE) and mediocre rate performance. Here, experimental and theoretical studies are combined to demonstrate the application of lithium‐pretreated HC (LPHC) as high‐performance anode materials for SIBs by manipulating the solid electrolyte interphase in tetraglyme (TEGDME)‐based electrolyte. The LPHC in TEGDME can 1) deliver > 92% ICE and ≈220 mAh g^?1 specific capacity, twice of the capacity (≈100 mAh g^?1) in carbonate electrolyte; 2) achieve > 85% capacity retention over 1000 cycles at 1000 mA g^?1 current density (4 C rate, 1 C = 250 mA g^?1) with a specific capacity of ≈150 mAh g^?1, ≈15 times of the capacity (10 mAh g^?1) in carbonate. The full cell of Na₃V₂(PO₄)₃‐LPHC in TEGDME demonstrated close to theoretical specific capacity of ≈98 mAh g^?1 based on Na₃V₂(PO₄)₃ cathode, ≈2.5 times of the value (≈40 mAh g^?1) with nontreated HC. This work provides new perception on the anode development for SIBs.     

MXene‐Based Mesoporous Nanosheets Toward Superior Lithium Ion Conductors

Although solid polymer electrolytes have some intrinsic advantages in synthesis and film processing compared with inorganic solid electrolytes, low ionic conductivities and mechanical moduli hamper their practical applications in lithium‐based batteries. Here, an efficient strategy is developed to produce a unique solid polymer electrolyte containing MXene‐based mesoporous silica nanosheets with a sandwich structure, which are fabricated via controllable hydrolysis of tetraethyl orthosilicate around the surface of MXene‐Ti₃C₂ under the direction of cationic surfactants. Such unique nanosheets not only exhibit individual, thin, and insulated features, but also possess abundant functional groups in mesopores and on the surface, which are favorable for the formation of Lewis acid–base interactions with anions in polymer electrolytes such as poly(propylene oxide) elastomer, enabling the fast Li⁺ transportation at the mesoporous nanosheets/polymer interfaces. As a consequence, a solid polymer electrolyte with high ionic conductivity of 4.6 × 10^?4 S cm^?1, high Young's modulus of 10.5 MPa, and long‐term electrochemical stability is achieved.     

Highly Reversible Na Storage in Na3V2(PO4)3 by Optimizing Nanostructure and Rational Surface Engineering

Sodium‐ion batteries (NIBs) have attracted more and more attention as economic alternatives for lithium‐ion batteries (LIBs). Sodium super ionic conductor (NASICON) structure materials, known for high conductivity and chemical diffusion coefficient of Na⁺ (≈10^?14 cm² s^?1), are promising electrode materials for NIBs. However, NASICON structure materials often suffer from low electrical conductivity (<10^?4 S cm^?1), which hinders their electrochemical performance. Here high performance sodium storage performance in Na₃V₂(PO₄)₃ (NVP) is realized by optimizing nanostructure and rational surface engineering. A N, B codoped carbon coated three‐dimensional (3D) flower‐like Na₃V₂(PO₄)₃ composite (NVP@C‐BN) is designed to enable fast ions/electrons transport, high‐surface controlled energy storage, long‐term structural integrity, and high‐rate cycling. The conductive 3D interconnected porous structure of NVP@C‐BN greatly releases mechanical stress from Na⁺ extraction/insertion. In addition, extrinsic defects and active sites introduced by the codoping heteroatoms (N, B) both enhance Na⁺ and e^? diffusion. The NVP@C‐BN displays excellent electrochemical performance as the cathode, delivering reversible capacity of 70% theoretical capacity at 100 C after 2000 cycles. When used as anode, the NVP@C‐BN also shows super long cycle life (38 mA h g^?1 at 20 C after 5000 cycles). The design provides a novel approach to open up possibilities for designing high‐power NIBs.     

A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

Flexible,Scalable, and Highly Conductive Garnet‐Polymer Solid Electrolyte Templated by Bacterial Cellulose

Solid‐state electrolytes are a promising candidate for the next‐generation lithium‐ion battery, as they have the advantages of eliminating the leakage hazard of liquid solvent and elevating stability. However, inherent limitations such as the low ionic conductivity of solid polymer electrolytes and the high brittleness of inorganic ceramic electrolytes severally impede their practical application. Here, an inexpensive, facile, and scalable strategy to fabricate a hybrid Li₇La₃Zr₂O₁₂ (LLZO) and poly(ethylene oxide)‐based electrolyte by exploiting bacterial cellulose as a template is reported. The well‐organized LLZO network significantly enhances the ionic conductivity by extending long transport pathways for Li ions, exhibiting an elevated conductivity of 1.12 × 10^?4 S cm^?1. In addition, the hybrid electrolyte presents a structural flexibility, with minor impedance increase after bending. The facile and applicable approach establishes new principles for the strategy of designing scalable and flexible hybrid polymer electrolytes that can be utilized for high‐energy‐density batteries.     

Facilitating Interfacial Stability Via Bilayer Heterostructure Solid Electrolyte Toward High‐energy,Safe and Adaptable Lithium Batteries

Solid‐state electrolytes are widely anticipated to enable the revival of high energy density and safe metallic Li batteries, however, their lower ionic conductivity at room temperature, stiff interfacial contact, and severe polarization during cycling continue to pose challenges in practical applications. Herein, a dual‐composite concept is applied to the design of a bilayer heterostructure solid electrolyte composed of Li⁺ conductive garnet nanowires (Li_6.75La₃Zr_1.75Nb_0.25O₁₂)/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐HFP) as a tough matrix and modified metal organic framework particles/polyethylene oxide/PVDF‐HFP as an interfacial gel. The integral ionic conductivity of the solid electrolyte reaches 2.0 × 10^?4 S cm^?1 at room temperature. In addition, a chemically/electrochemically stable interface is rapidly formed, and Li dendrites are well restrained by a robust inorganic shield and matrix. As a result, steady Li plating/stripping for more than 1700 h at 0.25 mA cm^?2 is achieved. Solid‐state batteries using this bilayer heterostructure solid electrolyte deliver promising battery performance (efficient capacity output and cycling stability) at ambient temperature (25 °C). Moreover, the pouch cells exhibit considerable flexibility in service and unexpected endurance under a series of extreme abuse tests including hitting with a nail, burning, immersion under water, and freezing in liquid nitrogen.     

Realizing Three‐Electron Redox Reactions in NASICON‐Structured Na3MnTi(PO4)3 for Sodium‐Ion Batteries

Developing multielectron reaction electrode materials is essential for achieving high specific capacity and high energy density in secondary batteries; however, it remains a great challenge. Herein, Na₃MnTi(PO₄)₃/C hollow microspheres with an open and stable NASICON framework are synthesized by a spray‐drying‐assisted process. When applied as a cathode material for sodium‐ion batteries, the resultant Na₃MnTi(PO₄)₃/C microspheres demonstrate fully reversible three‐electron redox reactions, corresponding to the Ti^3+/4+ (≈2.1 V), Mn^2+/3+ (≈3.5 V), and Mn^3+/4+ (≈4.0 V vs Na⁺/Na) redox couples. In situ X‐ray diffraction results reveals that both solid‐solution and two‐phase electrochemical reactions are involved in the sodiation/desodiation processes. The high specific capacity (160 mAh g^?1 at 0.2 C), outstanding cyclability (≈92% capacity retention after 500 cycles at 2 C), and the facile synthesis make the Na₃MnTi(PO₄)₃/C a prospective cathode material for sodium‐ion batteries.     

Stable Seamless Interfaces and Rapid Ionic Conductivity of Ca–CeO2/LiTFSI/PEO Composite Electrolyte for High‐Rate and High‐Voltage All‐Solid‐State Battery

Stable and seamless interfaces among solid components in all‐solid‐state batteries (ASSBs) are crucial for high ionic conductivity and high rate performance. This can be achieved by the combination of functional inorganic material and flexible polymer solid electrolyte. In this work, a flexible all‐solid‐state composite electrolyte is synthesized based on oxygen‐vacancy‐rich Ca‐doped CeO₂ (Ca–CeO₂) nanotube, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), and poly(ethylene oxide) (PEO), namely Ca–CeO₂/LiTFSI/PEO. Ca–CeO₂ nanotubes play a key role in enhancing the ionic conductivity and mechanical strength while the PEO offers flexibility and assures the stable seamless contact between the solid electrolyte and the electrodes in ASSBs. The as‐prepared electrolyte exhibits high ionic conductivity of 1.3 × 10^?4 S cm^?1 at 60 °C, a high lithium ion transference number of 0.453, and high‐voltage stability. More importantly, various electrochemical characterizations and density functional theory (DFT) calculations reveal that Ca–CeO₂ helps dissociate LiTFSI, produce free Li ions, and therefore enhance ionic conductivity. The ASSBs based on the as‐prepared Ca–CeO₂/LiTFSI/PEO composite electrolyte deliver high‐rate capability and high‐voltage stability.     

Viscoelastic and Nonflammable Interface Design–Enabled Dendrite‐Free and Safe Solid Lithium Metal Batteries

Herein, a composite polymer electrolyte with a viscoelastic and nonflammable interface is designed to handle the contact issue and preclude Li dendrite formation. The composite polymer electrolyte (cellulose acetate/polyethylene glycol/Li_1.4Al_0.4Ti_1.6P₃O₁₂) exhibits a wide electrochemical window of 5 V (vs Li⁺/Li), a high Li⁺ transference number of 0.61, and an excellent ionic conductivity of above 10^?4 S cm^?1 at 60 °C. In particular, the intimate contact, low interfacial impedance, and fast ion‐transport process between the electrodes and solid electrolytes can be simultaneously achieved by the viscoelastic and nonflammable layer. Benefiting from this novel design, solid lithium metal batteries with either LiFePO₄ or LiCoO₂ as cathode exhibit superior cyclability and rate capability, such as a discharge capacity of 157 mA h g^?1 after 100 cycles at C/2 and 97 mA h g^?1 at 5C for LiFePO₄ cathode. Moreover, the smooth and uniform Li surface after long‐term cycling confirms the successful suppression of dendrite formation. The viscoelastic and nonflammable interface modification of solid electrolytes provides a promising and general strategy to handle the interfacial issues and improves the operative safety of solid lithium metal batteries.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

Solvent‐Free Synthesis of Thin,Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Thin solid‐state electrolytes with nonflammability, high ionic conductivity, low interfacial resistance, and good processability are urgently required for next‐generation safe, high energy density lithium metal batteries. Here, a 3D Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZTO) self‐supporting framework interconnected by polytetrafluoroethylene (PTFE) binder is prepared through a simple grinding method without any solvent. Subsequently, a garnet‐based composite electrolyte is achieved through filling the flexible 3D LLZTO framework with a succinonitrile solid electrolyte. Due to the high content of garnet ceramic (80.4 wt%) and high heat‐resistance of the PTFE binder, such a composite electrolyte film with nonflammability and high processability exhibits a wide electrochemical window of 4.8 V versus Li/Li⁺ and high ionic transference number of 0.53. The continuous Li⁺ transfer channels between interconnected LLZTO particles and succinonitrile, and the soft electrolyte/electrode interface jointly contribute to a high ambient‐temperature ionic conductivity of 1.2 × 10^?4 S cm^?1 and excellent long‐term stability of the Li symmetric battery (stable at a current density of 0.1 mA cm^?2 for over 500 h). Furthermore, as‐prepared LiFePO₄|Li and LiNi_0.5Mn_0.3Co_0.2O₂|Li batteries based on the thin composite electrolyte exhibit high discharge specific capacities of 153 and 158 mAh g^?1 respectively, and desirable cyclic stabilities at room temperature.     

Nanoconfined Carbon‐Coated Na3V2(PO4)3 Particles in Mesoporous Carbon Enabling Ultralong Cycle Life for Sodium‐Ion Batteries

Na₃V₂(PO₄)₃ (denoted as NVP) has been considered as a promising cathode material for room temperature sodium ion batteries. Nevertheless, NVP suffers from poor rate capability resulting from the low electronic conductivity. Here, the feasibility to approach high rate capability by designing carbon‐coated NVP nanoparticles confined into highly ordered mesoporous carbon CMK‐3 matrix (NVP@C@CMK‐3) is reported. The NVP@C@CMK‐3 is prepared by a simple nanocasting technique. The electrode exhibits superior rate capability and ultralong cyclability (78 mA h g^?1 at 5 C after 2000 cycles) compared to carbon‐coated NVP and pure NVP cathode. The improved electrochemical performance is attributed to double carbon coating design that combines a variety of advantages: very short diffusion length of Na⁺/e^? in NVP, easy access of electrolyte, and short transport path of Na⁺ through carbon toward the NVP nanoparticle, high conductivity transport of electrons through the 3D interconnected channels of carbon host. The optimum design of the core–shell nanostructures with double carbon coating permits fast kinetics for both transported Na⁺ ions and electrons, enabling high‐power performance.     

A Metal Organic Framework Derived Solid Electrolyte for Lithium–Sulfur Batteries

Lithium–sulfur batteries (LSBs) are currently considered as promising candidates for next‐generation energy storage technologies. However, their practical application is hindered by the critical issue of the polysulfide‐shuttle. Herein, a metal organic framework (MOF)‐derived solid electrolyte is presented to address it. The MOF solid electrolyte is developed based on a Universitetet i Oslo (UIO) structure. By grafting a lithium sulfonate (‐SO₃Li) group to the UIO ligand, both the ionic conductivity and the polysulfide‐suppression capability of the resulting ‐SO₃Li grafted UIO (UIOSLi) solid electrolyte are greatly improved. After integrating a Li‐based ionic liquid (Li‐IL), lithium bis(trifluoromethanesulfonyl)imide in 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide, the resulting Li‐IL/UIOSLi solid electrolyte exhibits an ionic conductivity of 3.3 × 10^?4 S cm^?1 at room temperature. Based on its unique structure, the Li‐IL/UIOSLi solid electrolyte effectively restrains the polysulfide shuttle and suppresses lithium dendritic growth. Lithium–sulfur cells with the Li‐IL/UIOSLi solid electrolyte and a Li₂S₆ catholyte show stable cycling performance that preserves 84% of the initial capacity after 250 cycles with a capacity‐fade rate of 0.06% per cycle.     

Fast and Stable Proton Conduction in Heavily Scandium‐Doped Polycrystalline Barium Zirconate at Intermediate Temperatures

The environmental benefits of fuel cells and electrolyzers have become increasingly recognized in recent years. Fuel cells and electrolyzers that can operate at intermediate temperatures (300–450 °C) require, in principle, neither the precious metal catalysts that are typically used in polymer‐electrolyte‐membrane systems nor the costly heat‐resistant alloys used in balance‐of‐plant components of high‐temperature solid oxide electrochemical cells. These devices require an electrolyte with high ionic conductivity, typically more than 0.01 S cm^?1, and high chemical stability. To date, however, high ionic conductivities have been found in chemically unstable materials such as CsH₂PO₄, In‐doped SnP₂O₇, BaH₂, and LaH_3?2xO_x. Here, fast and stable proton conduction in 60‐at% Sc‐doped barium zirconate polycrystal, with a total conductivity of 0.01 S cm^?1 at 396 °C for 200 h is demonstrated. Heavy doping of Sc in barium zirconate simultaneously enhances the proton concentration, bulk proton diffusivity, specific grain boundary conductivity, and grain growth. An accelerated stability test under a highly concentrated and humidified CO₂ stream using in situ X‐ray diffraction shows that the perovskite phase is stable over 240 h at 400 °C under 0.98 atm of CO₂. These results show great promises as an electrolyte in solid‐state electrochemical devices operated at intermediate temperatures.     

“Water‐in‐Salt” Electrolyte Makes Aqueous Sodium‐Ion Battery Safe,Green, and Long‐Lasting

Narrow electrochemical stability window (1.23 V) of aqueous electrolytes is always considered the key obstacle preventing aqueous sodium‐ion chemistry of practical energy density and cycle life. The sodium‐ion water‐in‐salt electrolyte (NaWiSE) eliminates this barrier by offering a 2.5 V window through suppressing hydrogen evolution on anode with the formation of a Na⁺‐conducting solid‐electrolyte interphase (SEI) and reducing the overall electrochemical activity of water on cathode. A full aqueous Na‐ion battery constructed on Na_0.66[Mn_0.66Ti_0.34]O₂ as cathode and NaTi₂(PO₄)₃ as anode exhibits superior performance at both low and high rates, as exemplified by extraordinarily high Coulombic efficiency (>99.2%) at a low rate (0.2 C) for >350 cycles, and excellent cycling stability with negligible capacity losses (0.006% per cycle) at a high rate (1 C) for >1200 cycles. Molecular modeling reveals some key differences between Li‐ion and Na‐ion WiSE, and identifies a more pronounced ion aggregation with frequent contacts between the sodium cation and fluorine of anion in the latter as one main factor responsible for the formation of a dense SEI at lower salt concentration than its Li cousin.     

Low‐Cost Hollow Mesoporous Polymer Spheres and All‐Solid‐State Lithium,Sodium Batteries

A practical, low‐cost synthesis of hollow mesoporous organic polymer (HMOP) spheres is reported. The electrochemical properties of Li⁺/Na⁺‐electrolyte membranes with these spheres substituting for oxide filler particles in poly(ethylene oxide) (PEO)‐filler composite are explored. The electrolyte membranes are mechanically robust, thermally stable to over 250 °C, and block dendrites from a metallic‐lithium/sodium anode. The Li⁺/Na⁺ transfer impedance across the lithium/sodium–electrolyte interface is initially acceptable at 65 °C and scavenging of impurities by the porous‐spheres filler lowers this impedance relative to that with Al₂O₃. All‐solid‐state Li/LiFePO₄ and Na/NaTi₂(PO4)₃ cells give stable discharge capacity of ≈130 and 80 mAh g^?1, respectively, at 0.5 C and 65 °C for 100 cycles.