Organic Field‐Effect Transistor for Energy‐Related Applications: Low‐Power‐Consumption Devices,Near‐Infrared Phototransistors,and Organic Thermoelectric Devices

The organic field‐effect transistor (OFET) is the basic building block of integrated circuits. The charge carrier mobility and operating frequency of OFETs have continued to increase; therefore, the power dissipation of OFETs can no longer be ignored. Many research efforts have been made to develop low‐power‐consumption OFETs and complementary circuits. Despite the switching function, OFETs can also be utilized in emerging energy‐related applications, such as near‐infrared (NIR) photodetectors and organic thermoelectric devices. Organic phototransistors show considerably higher photo responsivity than other photodetector architectures due to field‐effect charge modulation. The photoinduced gate modulating largely suppresses the dark current while simultaneously providing gain. These characteristics may favor NIR light detection and suggest that the organic phototransistor is a promising candidate for optoelectronic applications in the NIR regime. For organic thermoelectric applications, OFETs can work as a powerful tool for examining the charge and energy transport in the organic semiconductor, thus giving insight into organic thermoelectric studies. In this review, the authors highlight recent advances in OFET‐ related energy topics, including low‐power‐consumption OFETs, NIR photodetectors, and organic thermoelectric devices. The remaining challenges in the field will also be discussed.     

Impact of Fullerene Molecular Weight on P3HT:PCBM Microstructure Studied Using Organic Thin‐Film Transistors

The clustering and diffusion of C₇₁‐butyric acid methyl ester (PC₇₁BM) in poly(3‐hexylthiophene) (P3HT) has been studied using single layer blend and bilayer organic field‐effect transistors (OFETs) and by atomic force microscopy (AFM). P3HT:PC₇₁BM blend based OFETs were found to undergo phase‐segregation upon annealing, which was detectable as a fall in electron mobility with increasing annealing temperature. By employing carefully designed bilayer P3HT:PC₇₁BM OFETs, the diffusion‐properties of PC₇₁BM in P3HT could additionally be inferred from electron mobility measurements. It was found that the prerequisite annealing temperatures for detectable PC₇₁BM clustering and diffusion in P3HT was approximately 20 °C higher than for PC₆₁BM. The diffusion coefficient of PC₆₁BM in P3HT was found to be several times higher that that of PC₇₁BM. The present work provides unique insights into the diffusion process of fullerenes in conjugated polymers and could prove highly valuable for future materials development and device optimization.     

Metal‐Organic Framework‐Derived Carbons for Battery Applications

The applications of carbon and carbon‐based materials with high porosity, high surface area, and functionalities based on metal‐organic framework precursors and/or templates have attracted significant research interest in recent years, particularly in the field of batteries. The chemical and physical properties of carbon and carbon‐based materials obtained by the heat treatment of various metal‐organic framework precursors or templates are improved to a certain extent. In this comprehensive review, the synthetic methods and electrochemical performance of carbon materials derived from metal‐organic frameworks (metal/carbon, metal oxide/carbon, nitrogen‐doped carbon, porous carbon, etc.) along with their applications in batteries are outlined.     

Design‐to‐Device Approach Affords Panchromatic Co‐Sensitized Solar Cells

Data‐driven materials discovery has become increasingly important in identifying materials that exhibit specific, desirable properties from a vast chemical search space. Synergic prediction and experimental validation are needed to accelerate scientific advances related to critical societal applications. A design‐to‐device study that uses high‐throughput screens with algorithmic encodings of structure–property relationships is reported to identify new materials with panchromatic optical absorption, whose photovoltaic device applications are then experimentally verified. The data‐mining methods source 9431 dye candidates, which are auto‐generated from the literature using a custom text‐mining tool. These candidates are sifted via a data‐mining workflow that is tailored to identify optimal combinations of organic dyes that have complementary optical absorption properties such that they can harvest all available sunlight when acting as co‐sensitizers for dye‐sensitized solar cells (DSSCs). Six promising dye combinations are shortlisted for device testing, whereupon one dye combination yields co‐sensitized DSSCs with power conversion efficiencies comparable to those of the high‐performance, organometallic dye, N719. These results demonstrate how data‐driven molecular engineering can accelerate materials discovery for panchromatic photovoltaic or other applications.     

In‐situ Crosslinking and n‐Doping of Semiconducting Polymers and Their Application as Efficient Electron‐Transporting Materials in Inverted Polymer Solar Cells

In this study, we demonstrate in‐situ n‐doping and crosslinking of semiconducting polymers as efficient electron‐transporting materials for inverted configuration polymer solar cells. The semiconducting polymers were crosslinked with bis(perfluorophenyl) azide (bis‐PFPA) to form a robust solvent‐resistant film, thereby preventing solvent‐induced erosion during subsequent solution‐based device processing. In addition, chemical n‐doping of semiconducting polymers with (4‐(1,3‐dimethyl‐2,3‐dihydro‐1H‐benzoimidazol‐2‐yl)phenyl)dimethylamine (N‐DMBI) substantially improved the power conversion efficiency of solar cells from 0.69% to 3.42%. These results open the way for progress on generally applicable polymeric interface materials, providing not only high device performance but also an effective fabrication method for solution‐processed multilayer solar cell devices.     

On the Functionality of Coatings for Cathode Active Materials in Thiophosphate‐Based All‐Solid‐State Batteries

The last decade has seen considerable advancements in the development of solid electrolytes for solid‐state battery applications, with particular attention being paid to sulfide superionic conductors. Importantly, the intrinsic electrochemical instability of these high‐performance separators highlights the notion that further progress in the field of solid‐state batteries is contingent on the optimization of component material interfaces in order to secure high energy and power densities, while maintaining device safety and a practical cycle life. On the cathode side, the need for a protective coating to inhibit solid electrolyte degradation is clear; however, a mechanistic understanding of the coating functionality remains unresolved, and there is still much room for improvement regarding the methodology and associated material properties. Herein, the essential requirements for a suitable coating are specified and fundamental considerations are discussed in detail. Additionally, this article will provide an overview of the various material classes, assessment protocols and practical coating methods, as well as an outlook on the development of coatings for cathode active materials in thiophosphate‐based solid‐state batteries.     

All‐Organic Battery Composed of Thianthrene‐ and TCAQ‐Based Polymers

An all‐organic battery consisting of two redox‐polymers, namely poly(2‐vinylthianthrene) and poly(2‐methacrylamide‐TCAQ) is assembled. This all‐organic battery shows excellent performance characteristics, namely flat discharge plateaus, an output voltage exceeding 1.3 V, and theoretical capacities of both electrodes higher than 100 mA h g^?1. Both organic electrode materials are synthesized in two respective three synthetic steps using the free‐radical polymerization technique. Li‐organic batteries manufactured from these polymers prove their suitability as organic electrode materials. The cathode material poly(2‐vinylthianthrene) (3) displays a discharging plateau at 3.95 V versus Li⁺/Li and a discharge capacity of 105 mA h g^?1, corresponding to a specific energy of about 415 mW h g^?1. The anode material poly(2‐methacrylamide‐TCAQ) (7) exhibits an initial discharge capacity of 130 mA h g^?1, corresponding to 94% material activity. The combination of both materials results in an all‐organic battery with a discharge voltage of 1.35 V and an initial discharge capacity of 105 mA h g^?1 (95% material activity).     

Doping‐Induced Screening of the Built‐in‐Field in Organic Solar Cells: Effect on Charge Transport and Recombination

We report on the effects of screening of the electric field by doping‐induced mobile charges on photocurrent collection in operational organic solar cells. Charge transport and recombination were studied using double injection (DI) and charge extraction by linearly increasing voltage (CELIV) transient techniques in bulk‐heterojunction solar cells made from acceptor‐donor blends of poly(3‐n‐hexylthiophene):phenyl‐C61‐butyric acid methyl ester (P3HT:PC60BM). It is shown that the screening of the built‐in field in operational solar cells can be controlled by an external voltage while the influence on charge transport and recombination is measured. An analytical theory to extract the bimolecular recombination coefficient as a function of electric field from the injection current is also reported. The results demonstrate that the suppressed (non‐Langevin) bimolecular recombination rate and charge collection are not strongly affected by native doping levels in this materials combination. Hence, it is not necessary to reduce the level of doping further to improve the device performance of P3HT‐based solar cells.     

Exfoliated Triazine‐Based Covalent Organic Nanosheets with Multielectron Redox for High‐Performance Lithium Organic Batteries

The development of the next‐generation lithium ion battery requires environmental‐friendly electrode materials with long cycle life and high energy density. Organic compounds are a promising potential source of electrode materials for lithium ion batteries due to their advantages of chemical richness at the molecular level, cost benefit, and environmental friendliness, but they suffer from low capacity and dissatisfactory cycle life mainly due to hydrophobic dissolution in organic electrolytes and poor electronic conductivity. In this work, two types of triazine‐based covalent organic nanosheets (CONs) are exfoliated and composited with carbon nanotubes. The thin‐layered 2D structure for the exfoliated CONs can activate more functional groups for lithium storage and boost the utilization efficiency of redox sites compared to its bulk counterpart. Large reversible capacities of above 1000 mAh g^?1 can be achieved after 250 cycles, which is comparable to high‐capacity inorganic electrodes. Moreover, the lithium‐storage mechanism is determined to be an intriguing 11 and 16 electron redox reaction, associated with the organic groups (unusual triazine ring, piperazine ring, and benzene ring, and common C?N, ? NH? groups).     

Interface Engineering for Highly Efficient and Stable Planar p‐i‐n Perovskite Solar Cells

Organic‐inorganic halide perovskite materials have become a shining star in the photovoltaic field due to their unique properties, such as high absorption coefficient, optimal bandgap, and high defect tolerance, which also lead to the breathtaking increase in power conversion efficiency from 3.8% to over 22% in just seven years. Although the highest efficiency was obtained from the TiO₂ mesoporous structure, there are increasing studies focusing on the planar structure device due to its processibility for large‐scale production. In particular, the planar p‐i‐n structure has attracted increasing attention on account of its tremendous advantages in, among other things, eliminating hysteresis alongside a competitive certified efficiency of over 20%. Crucial for the device performance enhancement has been the interface engineering for the past few years, especially for such planar p‐i‐n devices. The interface engineering aims to optimize device properties, such as charge transfer, defect passivation, band alignment, etc. Herein, recent progress on the interface engineering of planar p‐i‐n structure devices is reviewed. This review is mainly focused on the interface design between each layer in p‐i‐n structure devices, as well as grain boundaries, which are the interfaces between polycrystalline perovskite domains. Promising research directions are also suggested for further improvements.     

Less is More: Dopant‐Free Hole Transporting Materials for High‐Efficiency Perovskite Solar Cells

Perovskite solar cells have delivered power conversion efficiency beyond 22% in less than seven years, implying the potential for the paradigm shift of low‐cost photovoltaics with high efficiency and low embedded energy. Besides the “perovskite fever,” the development of new hole transport materials (HTM), especially dopant‐free HTMs, is another research hotspot. This is because the currently used HTMs, such as spiro‐OMeTAD derivatives, require additional chemical doping process to ensure sufficient conductivity and proper ionic potential level for efficient hole transport and collection. However, the commonly used dopants are volatile and hygroscopic which not only increase the complexity and cost of device fabrication but also deteriorate the device stability. So far, there have been several reviews on new HTMs, but review or analysis on dopant‐free HTMs is scarce. In this review, all reported dopant‐free HTMs are categorized into four primary different types and lessons will be learned during the separate discussions. The stability test behavior of all the intrinsic HTMs will be evaluated directly. In the end, the correlations between the properties of the intrinsic HTMs and parameters of the devices will be plotted to shed light on the future direction of development of this field.     

High‐Efficiency Nonfullerene Organic Solar Cells: Critical Factors that Affect Complex Multi‐Length Scale Morphology and Device Performance

Organic solar cells (OSCs) made of donor/acceptor bulk‐heterojunction active layers have been of widespread interest in converting sunlight to electricity. Characterizing of the complex morphology at multiple length scales of polymer:nonfullerene small molecular acceptor (SMA) systems remains largely unexplored. Through detailed characterizations (hard/soft X‐ray scattering) of the record‐efficiency polymer:SMA system with a close analog, quantitative morphological parameters are related to the device performance parameters and fundamental morphology–performance relationships that explain why additive use and thermal annealing are needed for optimized performance are established. A linear correlation between the average purity variations at small length scale (≈10 nm) and photovoltaic device characteristics across all processing protocols is observed in ≈12%‐efficiency polymer:SMA systems. In addition, molecular interactions as reflected by the estimated Flory–Huggins interaction parameters are used to provide context of the room temperature morphology results. Comparison with results from annealed devices suggests that the two SMA systems compared show upper and lower critical solution temperature behavior, respectively. The in‐depth understanding of the complex multilength scale nonfullerene OSC morphology may guide the device optimization and new materials development and indicates that thermodynamic properties of materials systems should be studied in more detail to aid in designing optimized protocols efficiently.     

Flexible Quasi‐Solid‐State Sodium‐Ion Capacitors Developed Using 2D Metal–Organic‐Framework Array as Reactor

Achieving high‐performance Na‐ion capacitors (NICs) has the particular challenge of matching both capacity and kinetics between the anode and cathode. Here a high‐power NIC full device constructed from 2D metal–organic framework (MOFs) array is reported as the reactive template. The MOF array is converted to N‐doped mesoporous carbon nanosheets (mp‐CNSs), which are then uniformly encapsulated with VO₂ and Na₃V₂(PO₄)₃ (NVP) nanoparticles as the electroactive materials. By this method, the high‐power performance of the battery materials is enabled to be enhanced significantly. It is discovered that such hybrid NVP@mp‐CNSs array can render ultrahigh rate capability (up to 200 C, equivalent to discharge within 18 s) and superior cycle performance, which outperforms all NVP‐based Na‐ion battery cathodes reported so far. A quasi‐solid‐state flexible NIC based on the NVP@mp‐CNSs cathode and the VO₂@mp‐CNSs anode is further assembled. This hybrid NIC device delivers both high energy density and power density as well as a good cycle stability (78% retention after 2000 cycles at 1 A g^?1). The results demonstrate the powerfulness of MOF arrays as the reactor for fabricating electrode materials.     

Insights from Machine Learning Techniques for Predicting the Efficiency of Fullerene Derivatives‐Based Ternary Organic Solar Cells at Ternary Blend Design

Ternary organic solar cells (OSCs) have progressed significantly in recent years due to the sufficient photon harvesting of the blend photoactive layer including three absorption‐complementary materials. With the rapid development of highly efficient ternary OSCs in photovoltaics, the precise energy‐level alignment of the three active components within ternary OSC devices should be taken into account. The machine‐learning technique is a computational method that can effectively learn from previous historical data to build predictive models. In this study, a dataset of 124 fullerene derivatives‐based ternary OSCs is manually constructed from a diverse range of literature along with their frontier molecular orbital theory levels, and device structures. Different machine‐learning algorithms are trained based on these electronic parameters to predict photovoltaic efficiency. Thus, the best predictive capability is provided by using the Random Forest approach beyond other machine‐learning algorithms in the dataset. Furthermore, the Random Forest algorithm yields valuable insights into the crucial role of lowest unoccupied molecular orbital energy levels of organic donors in the performance of ternary OSCs. The outcome of this study demonstrates a smart strategy for extracting underlying complex correlations in fullerene derivatives‐based ternary OSCs, thereby accelerating the development of ternary OSCs and related research fields.     

A Cross‐Linked Interconnecting Layer Enabling Reliable and Reproducible Solution‐Processing of Organic Tandem Solar Cells

The performance of tandem organic solar cells (OSCs) is directly related to the functionality and reliability of the interconnecting layer (ICL). However, it is a challenge to develop a fully functional ICL for reliable and reproducible fabrication of solution‐processed tandem OSCs with minimized optical and electrical losses, in particular for being compatible with various state‐of‐the‐art photoactive materials. Although various ICLs have been developed to realize tandem OSCs with impressively high performance, their reliability, reproducibility, and generic applicability are rarely analyzed and reported so far, which restricts the progress and widespread adoption of tandem OSCs. In this work, a robust and fully functional ICL is developed by incorporating a hydrolyzed silane crosslinker, (3‐glycidyloxypropyl)trimethoxysilane (GOPS), into poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), and its functionality for reliable and reproducible fabrication of tandem OSCs based on various photoactive materials is validated. The cross‐linked ICL can successfully protect the bottom active layer against penetration of high boiling point solvents during device fabrication, which widely broadens the solvent selection for processing photoactive materials with high quality and reliability, providing a great opportunity to continuously develop the tandem OSCs towards future large‐scale production and commercialization.     

Slot‐Die and Roll‐to‐Roll Processed Single Junction Organic Photovoltaic Cells with the Highest Efficiency

The record efficiency of the state‐of‐the‐art polymer solar cells (PSCs) is rapidly increasing, due to the discovery of high‐performance photoactive donor and acceptor materials. However, strong questions remain as to whether such high‐efficiency PSCs can be produced by scalable processes. This paper reports a high power conversion efficiency (PCE) of 13.5% achieved with single‐junction ternary PSCs based on PTB7‐Th, PC₇₁BM, and COi8DFIC fabricated by slot‐die coating, which shows the highest PCE ever reported in PSCs fabricated by a scalable process. To understand the origin of the high performance of the slot‐die coated device, slot‐die coated photoactive films and devices are systematically investigated. These results indicate that the good performance of the slot‐die PSCs can be due to a favorable molecule‐structure and film‐morphology change by introducing 1,8‐diiodooctane and heat treatment, which can lead to improved charge transport with reduced carrier recombination. The optimized condition is then used for the fabrication of large‐area modules and also for roll‐to‐roll fabrication. The slot‐die coated module with 30 cm² active‐area and roll‐to‐roll produced flexible PSC has shown 8.6% and 9.6%, respectively. These efficiencies are the highest in each category and demonstrate the strong potential of the slot‐die coated ternary system for commercial applications.     

Nanostructured p‐n Junctions for Kinetic‐to‐Electrical Energy Conversion

Piezoelectric ZnO nanorods grown on a flexible substrate are combined with the p‐type semiconducting polymer PEDOT:PSS to produce a p‐n junction device that successfully demonstrates kinetic‐to‐electrical energy conversion. Both the voltage and current output of the devices are measured to be in the range of 10 mV and 10 μA cm^?2. Combining these figures for the best device gives a maximum possible power density of 0.4 mW cm^?3. Systematic testing of the devices is performed showing that the voltage output increases linearly with applied stress, and is reduced significantly by illumination with super‐band gap light. This provides strong evidence that the voltage output results from piezoelectric effects in the ZnO. The behavior of the devices is explained by considering the time‐dependent changes in band structure resulting from the straining of a piezoelectric material within a p‐n junction. It is shown that the rate of screening of the depolarisation field determines the power output of a piezoelectric energy harvesting device. This model is consistent with the behavior of a number of previous devices utilising the piezoelectric effect in ZnO.     

An All‐Organic Non‐aqueous Lithium‐Ion Redox Flow Battery

A non‐aqueous lithium‐ion redox flow battery employing organic molecules is proposed and investigated. 2,5‐Di‐tert‐butyl‐1,4‐bis(2‐methoxyethoxy)benzene and a variety of molecules derived from quinoxaline are employed as initial high‐potential and low‐potential active materials, respectively. Electrochemical measurements highlight that the choice of electrolyte and of substituent groups can have a significant impact on redox species performance. The charge‐discharge characteristics are investigated in a modified coin‐cell configuration. After an initial break‐in period, coulombic and energy efficiencies for this unoptimized system are ～70% and ～37%, respectively, with major charge and discharge plateaus between 1.8‐2.4 V and 1.7‐1.3 V, respectively, for 30 cycles. Performance enhancements are expected with improvements in cell design and materials processing.     

Origin of the S‐Shaped JV Curve and the Light‐Soaking Issue in Inverted Organic Solar Cells

Inverted organic solar cells generally exhibit a strong s‐shaped kink in the current–voltage characteristics (JV curve) that may be removed by exposure to UV light (light‐soaking) leading to a drastically improved performance. Using in‐device characterization methods the origin of the light‐soaking issue in inverted solar cells employing titanium dioxide (TiO₂) as an electron selective layer is clarified. An injected hole reservoir accumulated at the TiO₂/organic interface of the pristine device is observed from extraction current transients; the hole reservoir increases the recombination and results in an s‐shape in the JV curve of pristine devices. The hole reservoir and the s‐shape is a result of the energetics at the selective contact in the pristine device; the effect of UV exposure is to decrease the work function of the indium tin oxide/TiO₂‐contact, increasing the built‐in potential. This hinders the build‐up of the hole reservoir and the s‐shape is removed. The proposed model is in excellent agreement with drift‐diffusion simulations.