Enhanced Rate Capability of Ion‐Accessible Ti3C2Tx‐NbN Hybrid Electrodes

Although 2D Ti₃C₂T_x is a good candidate for supercapacitors, the restacking of nanosheets hinders the ion transport significantly at high scan rates, especially under practical mass loading (>10 mg cm^?2) and thickness (tens of microns). Here, Ti₃C₂T_x‐NbN hybrid film is designed by self‐assembling Ti₃C₂T_x with 2D arrays of NbN nanocrystals. Working as an interlayer spacer of Ti₃C₂T_x, NbN facilitates the ion penetration through its 2D porous structure; even at extremely high scan rates. The hybrid film shows a thickness‐independent rate performance (almost the same rate capabilities from 2 to 20 000 mV s^?1) for 3 and 50 µm thick electrodes. Even a 109 µm thick Ti₃C₂T_x‐NbN electrode shows a better rate performance than 25 µm thick pure Ti₃C₂T_x electrodes. This method may pave a way to controlling ion transport in electrodes composed of 2D conductive materials, which have potential applications in high‐rate energy storage and beyond.     

Utilizing Waste Cable Wires for High‐Performance Fiber‐Based Hybrid Supercapacitors: An Effective Approach to Electronic‐Waste Management

In recent years, electronic waste (e‐waste) such as old cable wires, fans, circuit boards, etc., can be often seen in large piles of leftover in dumping yards. Employing these e‐waste sources for energy storage devices not only increases the economic value but also decreases the reliance on fossil fuels. In this context, waste cable wires are utilized to obtain precious copper (Cu) fibers and used as a cost‐effective current collector for the fabrication of fiber‐based hybrid supercapacitor (FHSC). With the braided Cu fibers, forest‐like nickel oxide nanosheet grafted carbon nanotube coupled copper oxide nanowire arrays (NiO NSs@CNTs@CuO NWAs/Cu fibers) are designed via simple wet‐chemical approaches. As a battery‐type material, the forest‐like NiO NSs@CNTs@CuO NWAs/Cu fiber electrode shows superior electrochemical properties including high specific capacity (230.48 mA h g^?1) and cycling stability (82.72%) in aqueous alkaline electrolyte. Moreover, a solid‐state FHSC is also fabricated using forest‐like NiO NSs@CNTs@CuO NWAs/Cu fibers as a positive electrode and activated carbon coated carbon fibers as a negative electrode with a gel electrolyte, which also shows a higher energy and power densities of 26.32 W h kg^?1 and 1218.33 W kg^?1, respectively. The flexible FHSC is further employed as an energy source for various electronic gadgets, demonstrating its suitability for wearable applications.     

High‐Performance Fiber‐Shaped All‐Solid‐State Asymmetric Supercapacitors Based on Ultrathin MnO2 Nanosheet/Carbon Fiber Cathodes for Wearable Electronics

Flexible fiber‐shaped supercapacitors have shown great potential in portable and wearable electronics. However, small specific capacitance and low operating voltage limit the practical application of fiber‐shaped supercapacitors in high energy density devices. Herein, direct growth of ultrathin MnO₂ nanosheet arrays on conductive carbon fibers with robust adhesion is exhibited, which exhibit a high specific capacitance of 634.5 F g^?1 at a current density of 2.5 A g^?1 and possess superior cycle stability. When MnO₂ nanosheet arrays on carbon fibers and graphene on carbon fibers are used as a positive electrode and a negative electrode, respectively, in an all‐solid‐state asymmetric supercapacitor (ASC), the ASC displays a high specific capacitance of 87.1 F g^?1 and an exceptional energy density of 27.2 Wh kg^?1. In addition, its capacitance retention reaches 95.2% over 3000 cycles, representing the excellent cyclic ability. The flexibility and mechanical stability of these ASCs are highlighted by the negligible degradation of their electrochemical performance even under severely bending states. Impressively, as‐prepared fiber‐shaped ASCs could successfully power a photodetector based on CdS nanowires without applying any external bias voltage. The excellent performance of all‐solid‐state ASCs opens up new opportunity for development of wearable and self‐powered nanodevices in near future.     

High‐Performance and Breathable Polypyrrole Coated Air‐Laid Paper for Flexible All‐Solid‐State Supercapacitors

High‐performance, breathable, conductive, and flexible polypyrrole (PPy) coated paper electrodes are prepared by an interfacial polymerization method using air‐laid paper as a substrate. Owing to the synergistic effect of superior electrical conductivity, high wettability, and the porous architecture, the prepared electrode not only shows an outstanding specific capacitance and rate abilities (3100 and 2579 mF cm^?2 at 1 and 20 mA cm^?2 for a PPy coated paper electrode), but also exhibits excellent flexibility, wearability, and breathability. Based on these superior features, an all‐solid‐state supercapacitor assembled with the PPy coated paper electrodes shows an outstanding energy density of 62.4 µW h cm^?2, remarkable air permeability and excellent flexibility to sustain various deformations. Furthermore, large‐scale fabrication of conductive flexible paper electrode can be easily achieved through this method. Therefore, this work offers a new vision for flexible energy storage.     

Ultrafast All‐Solid‐State Coaxial Asymmetric Fiber Supercapacitors with a High Volumetric Energy Density

Fiber‐supercapacitors (FSCs) are promising energy storage devices that can complement or even replace microbatteries in miniaturized portable and wearable electronics. Currently, a major challenge for FSCs is achieving ultrahigh volumetric energy and power densities simultaneously, especially when the charge/discharge rates exceed 1 V s^?1. Herein, an Au‐nanoparticle‐doped‐MnO_x@CoNi‐alloy@carbon‐nanotube (Au–MnO_x@CoNi@CNT) core/shell nanocomposite fiber electrode is designed, aiming to boost its charge/discharge rate by taking advantage of the superconductive CoNi alloy network and the greatly enhanced conductivity of the Au doped MnO_x active materials. An all‐solid‐state coaxial asymmetric FSC (CAFSC) prototype device made by wrapping this fiber with a holey graphene paper (HGP) exhibits excellent performance at rates up to 10 V s^?1, which is the highest charge rate demonstrated so far for FSCs based on pseudocapacitive materials. Furthermore, our fully packaged CAFSC delivers a volumetric energy density of ≈15.1 mW h cm^?3, while simultaneously maintaining a high power density of 7.28 W cm^?3 as well as a long cycle life (90% retention after 10 000 cycles). This value is the highest among all reported FSCs, even better than that of a typical 4 V/500 µA h thin‐film lithium battery.     

Large Voltage Generation of Flexible Thermoelectric Nanocrystal Thin Films by Finger Contact

This paper demonstrates that thermal energy radiated from a human finger can be converted efficiently into electricity by a nanocrystal (NC) thin film that substantially suppresses thermal conduction, but still allows electric conduction. The converting efficiencies of the chalcogenide NC thin films with dimensions 40 µm × 20 µm × 20 nm, prepared on flexible substrates by a solution process, are maximized by adjusting the NC size. A Seebeck coefficient of S = 1829 µV K^?1, and a dimensionless thermoelectric figure‐of‐merit, ZT = 0.68 are achieved at ambient temperature for p‐ and n‐type NC thin films, respectively. A thermoelectric array consisting of p‐ and n‐type NC thin films generates a voltage of 645 mV for a temperature gradient of 10 K. Furthermore, the donut‐shaped pn array can generate a voltage of 170 mV from the heat supplied by an individual's finger.     

Flexible Thermoelectric Generators Composed of n‐and p‐Type Silicon Nanowires Fabricated by Top‐Down Method

This study demonstrates the fabrication and characterization of a flexible thermoelectric (TE) power generator composed of silicon nanowires (SiNWs) fabricated by top‐down method and discusses its strain‐dependence analysis. The Seebeck coefficients of the p‐ and n‐type SiNWs used to form a pn‐module are 156.4 and ?146.1 µV K^?1, respectively. The maximum power factors of the p‐ and n‐type SiNWs are obtained as 8.79 and 8.87 mW (m K²)^?1, respectively, under a convex bending of 1.11%, respectively; these are the largest values among the power factors hitherto reported for SiNWs. The dimensionless figure of merit (ZT ) values of the SiNWs at room temperature are 6.8 × 10^?2 and 6.7 × 10^?2 for the convex bent p‐ and n‐type SiNWs, respectively, with a strain of 1.11%. The thermoelectric properties of the pn‐module and its component SiNWs are characterized under strain conditions ranging from ?1.11% to 1.11%. The maximum Seebeck coefficient and power factor of the pn‐module are obtained as 448 µV K^?1 and 14.2 mW (m K²)^?1, respectively, under convex bending of 1.11%. Moreover, the mechanical stability of the TE characteristics of the pn‐module is demonstrated through a continuous bending test of 3000 cycles under convex bending of 0.66%.     

Carbohydrate uptake in Advenella mimigardefordensis strain DPN7T is mediated by periplasmic sugar oxidation and a TRAP‐transport system

In this study, we investigated an SBP (DctP_Am) of a tripartite ATP‐independent periplasmic transport system (TRAP) in Advenella mimigardefordensis strain DPN7^T. Deletion of dctP_Am as well as of the two transmembrane compounds of the tripartite transporter, dctQ and dctM, impaired growth of A. mimigardefordensis strain DPN7^T, if cultivated on mineral salt medium supplemented with d ‐glucose, d ‐galactose, l ‐arabinose, d ‐fucose, d ‐xylose or d ‐gluconic acid, respectively. The wild type phenotype was restored during complementation studies of A. mimigardefordensis ΔdctP_Am using the broad host vector pBBR1MCS‐5::dctP_Am. Furthermore, an uptake assay with radiolabeled [¹⁴C(U)]‐d ‐glucose clearly showed that the deletion of dctP_Am, dctQ and dctM, respectively, disabled the uptake of this aldoses in cells of either mutant strain. Determination of K_D performing thermal shift assays showed a shift in the melting temperature of DctP_Am in the presence of d ‐gluconic acid (K_D 11.76 ± 1.3 µM) and the corresponding aldonic acids to the above‐mentioned carbohydrates d ‐galactonate (K_D 10.72 ± 1.4 µM), d ‐fuconic acid (K_D 13.50 ± 1.6 µM) and d ‐xylonic acid (K_D 8.44 ± 1.0 µM). The sugar (glucose) dehydrogenase activity (E.C.1.1.5.2) in the membrane fraction was shown for all relevant sugars, proving oxidation of the molecules in the periplasm, prior to transport.     

Yolk–Shell NiS2 Nanoparticle‐Embedded Carbon Fibers for Flexible Fiber‐Shaped Sodium Battery

Fiber‐shaped rechargeable batteries hold promise as the next‐generation energy storage devices for wearable electronics. However, their application is severely hindered by the difficulty in fabrication of robust fiber‐like electrodes with promising electrochemical performance. Herein, yolk–shell NiS₂ nanoparticles embedded in porous carbon fibers (NiS₂?PCF) are successfully fabricated and developed as high‐performance fiber electrodes for sodium storage. Benefiting from the robust embedded structure, 3D porous and conductive carbon network, and yolk–shell NiS₂ nanoparticles, the as‐prepared NiS₂?PCF fiber electrode achieves a high reversible capacity of about 679 mA h g^?1 at 0.1 C, outstanding rate capability (245 mA h g^?1 at 10 C), and ultrastable cycle performance with 76% capacity retention over 5000 cycles at 5 C. Notably, a flexible fiber‐shaped sodium battery is assembled, and high reversible capacity is kept at different bending states. This work offers a new electrode‐design paradigm toward novel carbon fiber electrodes embedded with transition metal oxides/sulfides/phosphides for application in flexible energy storage devices.     

Exceptionally Enhanced Electrode Activity of (Pr,Ce)O2−δ‐Based Cathodes for Thin‐Film Solid Oxide Fuel Cells

It is shown that an electrochemically‐driven oxide overcoating substantially improves the performance of metal electrodes in high‐temperature electrochemical applications. As a case study, Pt thin films are overcoated with (Pr,Ce)O_2?δ (PCO) by means of a cathodic electrochemical deposition process that produces nanostructured oxide layers with a high specific surface area and uniform metal coverage and then the coated films are examined as an O₂‐electrode for thin‐film‐based solid oxide fuel cells. The combination of excellent conductivity, reactivity, and durability of PCO dramatically improves the oxygen reduction reaction rate while maintaining the nanoscale architecture of PCO layers and thus the performance of the PCO‐coated Pt thin‐film electrodes at high temperatures. As a result, with an oxide coating step lasting only 5 min, the electrode resistance is successfully reduced by more than 1000 times at 500 °C in air. These observations provide a new direction for the design of high‐performance electrodes for high‐temperature electrochemical cells.     

Flexible Lead‐Free Perovskite Oxide Multilayer Film Capacitor Based on (Na0.8K0.2)0.5Bi0.5TiO3/Ba0.5Sr0.5(Ti0.97Mn0.03)O3 for High‐Performance Dielectric Energy Storage

Flexible thin film dielectric capacitors with high energy storage density and a fast charging–discharging rate have attracted increasing attention as the development of microelectronics progresses toward flexibility and miniaturization. In this work, an all‐inorganic thin film dielectric capacitor with a multilayer structure based on (Na_0.8K_0.2)_0.5Bi_0.5TiO₃ and Ba_0.5Sr_0.5(Ti_0.97Mn_0.03)O₃ is designed and synthesized on a mica substrate. By optimizing the periodic number (N), concomitantly enhanced breakdown strength and large polarization difference are achieved in the film with N = 6, which contributes to the large energy density (W_rec) of 91 J cm^?3, high efficiency (η) of 68%, and fast discharging rate of 47.6 µs. The obtained energy density is the highest value up to now in flexible dielectric capacitors, including lead‐free and lead‐based inorganic films as well as organic dielectric films. Moreover, no obvious deterioration of the energy storage performance is observed in the wide ranges of working temperature (?50–200 °C), operating frequency (500 Hz to 30 kHz), and fatigue cycles (1–10⁸). Besides, the W_rec and η are ultra‐stable under various bending radii (R = 12–2 mm) and even after 10⁴ bending cycles at R = 4 mm, demonstrating an outstanding mechanical bending endurance. This excellent performance will allow the capacitor thrive in flexible microenergy storage systems.     

Plasma‐Enhanced Atomic Layer Deposition of Ultrathin Oxide Coatings for Stabilized Lithium–Sulfur Batteries

One of the most challenging problems in the development of lithium–sulfur batteries is polysulfide dissolution, which leads to cell overcharge and low columbic efficiency. Here, we propose the formation of a thin conformal Li‐ion permeable oxide layer on the sulfur‐carbon composite electrode surface by rapid plasma enhanced atomic layer deposition (PEALD) in order to prevent this dissolution, while preserving electrical connectivity within the individual electrode particles. PEALD synthesis offers a fast deposition rate combined with a low operating temperature, which allows sulfur evaporation during deposition to be avoided. After PEALD of a thin layer of aluminium oxide on the surface of electrode composed of large (ca. 10 μm in diameter) S‐infiltrated activated carbon fibers (S‐ACF), significantly enhanced cycle life is observed, with a capacity in excess of 600 mA·h·g^?1 after 300 charge–discharge cycles. Scanning electron microscopy (SEM) shows a significant amount of redeposited lithium sulfides on the external surface of regular S‐ACF electrodes. However, the PEALD alumina‐coated electrodes show no lithium sulfide deposits on the fiber surface. Energy dispersive spectroscopy (EDS) studies of the electrodes’ chemical composition further confirms that PEALD alumina coatings dramatically reduce S dissolution from the cathodes by confining the polysulfides inside the alumina barrier.     

3D Si/C Fiber Paper Electrodes Fabricated Using a Combined Electrospray/Electrospinning Technique for Li‐Ion Batteries

Although the theoretical capacity of silicon is ten times higher than that of graphite, the overall electrode capacity of Si anodes is still low due to the low Si loading and heavy metal current collector. Here, a novel flexible 3D Si/C fiber paper electrode synthesized by simultaneously electrospraying nano‐Si‐PAN (polyacrylonitrile) clusters and electrospinning PAN fibers followed by carbonization is reported. The combined technology allows uniform incorporation of Si nanoparticles into a carbon textile matrix to form a nano‐Si/carbon composite fiber paper. The flexible 3D Si/C fiber paper electrode demonstrate a very high overall capacity of ≈1600 mAh g^‐1 with capacity loss less than 0.079% per cycle for 600 cycles and excellent rate capability. The exceptional performance is attributed to the unique architecture of the flexible 3D Si/C fiber paper, i.e., the resilient and conductive carbon fiber network matrix, carbon‐coated Si nanoparticle clusters, strong adhesion between carbon fibers and Si nanoparticle clusters, and uniform distribution of Si/C clusters in the carbon fiber frame. The scalable and facile synthesis method, good mechanical properties, and excellent electrochemical performance at a high Si loading make the flexible 3D Si/C fiber paper batteries extremely attractive for plug‐in electric vehicles, flexible electronics, space exploration, and military applications.     

Dynamic changes of canopy-scale mesophyll conductance to CO₂ diffusion of sunflower as affected by CO₂ concentration and abscisic acid

Leaf‐level measurements have shown that mesophyll conductance (g_m) can vary rapidly in response to CO₂ and other environmental factors, but similar studies at the canopy‐scale are missing. Here, we report the effect of short‐term variation of CO₂ concentration on canopy‐scale g_m and other CO₂ exchange parameters of sunflower (Helianthus annuus L.) stands in the presence and absence of abscisic acid (ABA) in their nutrient solution. g_m was estimated from gas exchange and on‐line carbon isotope discrimination (Δ_obs) in a ¹³CO₂/¹²CO₂ gas exchange mesocosm. The isotopic contribution of (photo)respiration to stand‐scale Δ_obs was determined with the experimental approach of Tcherkez et al. Without ABA, short‐term exposures to different CO₂ concentrations (C_a 100 to 900 µmol mol^?1) had little effect on canopy‐scale g_m. But, addition of ABA strongly altered the CO₂‐response: g_m was high (approx. 0.5 mol CO₂ m^?2 s^?1) at C_a < 200 µmol mol^?1 and decreased to <0.1 mol CO₂ m^?2 s^?1 at C_a >400 µmol mol^?1. In the absence of ABA, the contribution of (photo)respiration to stand‐scale Δ_obs was high at low C_a (7.2‰) and decreased to <2‰ at C_a > 400 µmol mol^?1. Treatment with ABA halved this effect at all C_a.     

Sn‐Alloy Foil Electrode with Mechanical Prelithiation: Full‐Cell Performance up to 200 Cycles

Self‐supporting Sn foil is a promising high‐volumetric‐capacity anode for lithium ion batteries (LIBs), but it suffers from low initial Coulombic efficiency (ICE). Here, mechanical prelithiation is adopted to improve ICE, and it is found that Sn foils with coarser grains are prone to cause electrode damage. To mitigate damage and prepare thinner lithiated electrodes, 3Ag0.5Cu96.5Sn foil is used that has more refined grains (5–10 µm) instead of Sn (50–100 µm), where the abundant grain boundaries (GBs) offer more sliding systems to release stress and reduce deep fractures. Thus, the thickness of Li_x3Ag0.5Cu96.5Sn can be reduced to 50 µm, compared to 100 µm Li_xSn. When the foils contact open air, the Sn‐Li‐O(H) products are more stable than Li‐O(H), thus Li_x3Ag0.5Cu96.5Sn shows outstanding air stability. The as‐prepared 50 µm foil anode achieves stable 200 cycles in LiFePO₄//Li_x3Ag0.5Cu96.5Sn full cell (≈2.65 mAh cm^?2) and the capacity retention is 95%. Even at 5C, the capacity of Li_x3Ag0.5Cu96.5Sn is still up to ≈1.8 mAh cm^?2. The cycle life of NCM523//Li_x3Ag0.5Cu96.5Sn full cell exceeds that of NCM523//Li. Furthermore, 70 µm Li_x3Ag0.5Cu96.5Sn is used as double‐sided anode for a 3 cm × 2.8 cm pouch cell and its actual volumetric capacity density is 674 mAh cm^?3 after 50 cycles.     

Toxic effects of chlorpyrifos on the growth,hematology, and different organs histopathology of Nile tilapia,Oreochromis niloticus

Chlorpyrifos is a widely applied insecticide that permeates on most waterways and affects aquatic organisms. The growth performances, hematological and histological impacts on Nile tilapia, Oreochromis niloticus following a 60 day of exposure to varying concentrations of chlorpyrifos 20 EC (T₁ 08 µgL^?1, T₂ 16 µgL^?1, and T₃ 32 µgL^?1) were compared to a control T_c 0 µgL^?1. The 96-hour LC50 of chlorpyrifos 20 EC was calculated as 46.80 μgL^?1. The water quality parameters were recorded regularly. The value of dissolved O₂ and NH₃ stayed rather steady, although temperature varied considerably. It was revealed that as chlorpyrifos levels go up, the percentage of weight gain (WG %), specific growth rates (SGR), and survival rate decreases. The control group T_c had the highest percentages of SGR weight (1.16 ± 0.58) and the T₃ group had the lowest percentages of SGR weight (0.25 ± 0.77). The hematological assessment showed significant differences of hemoglobin concentration, white blood cell counts and red blood cell numbers between chlorpyrifos treatment and control group (P < 0.05). Histological alterations in the liver, gills, and muscle tissues reported to be worse for T₃ as compared to others. There were no statistical differences in GSI, HSI values between control and treatment groups. The chlorpyrifos 20 EC was shown to be highly toxic to O. niloticus at sub-lethal dosages.     

Grafting Benzenediazonium Tetrafluoroborate onto LiNixCoyMnzO2 Materials Achieves Subzero‐Temperature High‐Capacity Lithium‐Ion Storage via a Diazonium Soft‐Chemistry Method

Subzero‐temperature Li‐ion batteries (LIBs) are highly important for specific energy storage applications. Although the nickel‐rich layered lithium transition metal oxides(LiNi_xCo_yMn_zO₂) (LNCM) (x > 0.5, x + y +z = 1) are promising cathode materials for LIBs, their very slow Li‐ion diffusion is a main hurdle on the way to achieve high‐performance subzero‐temperature LIBs. Here, a class of low‐temperature organic/inorganic hybrid cathode materials for LIBs, prepared by grafting a conducting polymer coating on the surface of 3 µm sized LiNi_0.6Co_0.2Mn_0.2O₂ (LNCM‐3) material particles via a greener diazonium soft‐chemistry method is reported. Specifically, LNCM‐3 particles are uniformly coated with a thin polyphenylene film via the spontaneous reaction between LNCM‐3 and C₆H₅N₂⁺BF₄^?. Compared with the uncoated one, the polyphenylene‐coated LNCM‐3 (polyphenylene/LNCM‐3) has shown much improved low‐temperature discharge capacity (≈148 mAh g^?1 at 0.1 C, ?20 °C), outstanding rate capability (≈105 mAh g^?1 at 1 C, ?20 °C), and superior low‐temperature long‐term cycling stability (capacity retention is up to 90% at 0.5 C over 1150 cycles). The low‐temperature performance of polyphenylene/LNCM‐3 is the best among the reported state‐of‐the art cathode materials for LIBs. The present strategy opens up a new avenue to construct advanced cathode materials for wider range applications.     

Determination of the rotational barriers of atropisomeric polychlorinated biphenyls (PCBs) by a novel stopped-flow multidimensional gas chromatographic technique

The rotational barriers ΔG^‡ (T) of the four atropisomeric polychlorinated biphenyls (PCBs) 2,2′,3,5′,6-pentachlorobiphenyl (PCB 95), 2,2′3,3′,4,6′-hexachlorobiphenyl (PCB 132), 2,2′,3,3′,6,6′-hexachlorobiphenyl (PCB 136), and 2,2′,3,4′,5′,6-hexachlorobiphenyl (PCB 149) were determined via on-line enantiomerization kinetics by a new stopped-flow multidimensional gas chromatographic technique (stopped-flow MDGC) employing Chirasil-Dex as chiral stationary phase for enantiomer separation. The calculated rotational barriers ΔG^‡ (T) of the trichloro-ortho-substituted atropisomers are 184 ± 2 kJ/mol for PCB 95, 189 ± 4 kJ/mol for PCB 132, and 184 ± 1 kJ/mol for PCB 149 at 300°C. The rotational barrier ΔG^‡ (T) of tetrachloro-ortho-substituted PCB 136 is at least (or higher than) 210 kJ/mol at 320°C. Chirality 10:316–320, 1998. © 1998 Wiley-Liss, Inc.     

Comparative characterization of the two primary pumps, H+-ATPase and Na+-ATPase, in the plasma membrane of the marine alga Tetraselmis viridis

The transport characteristics of the plasma membrane H⁺‐ATPase (PMHA) and Na⁺‐ATPase (PMNA) from marine unicellular green alga Tetraselmis viridis Rouch. were studied using sealed plasma membrane vesicles isolated from this species. The activities of the ATPases were investigated by monitoring the ATP‐dependent pH changes in the vesicle lumen. PMHA operation led to acidification of the vesicle lumen, whereas Na⁺ translocation into plasma membrane vesicles catalysed by PMNA was accompanied by H⁺ efflux, namely the alkalization of the vesicle lumen (Balnokin et al., FEBS Lett 462: 402–406, 1999). The intravesicular acidification and alkalization were detected with the ΔpH probe acridine orange and the pH probe pyranine, respectively. PMHA and PMNA were found to operate in distinct pH regions, maximal activity of PMHA being observed at pH 6.5 and that of PMNA at pH 7.8. Kinetic studies revealed that the ATPases have similar affinities to their primary substrate, MgATP complex (an apparent K_m = 34 ± 6.2 µM for PMHA and 73 ± 8.7 µM for PMNA). At the same time, the ATPases were differently affected by free Mg²⁺ and ATP. Free Mg²⁺ appeared to be a mixed‐type inhibitor for PMNA (K_i′ = 210 µM) but it did not suppress PMHA. Conversely, free ATP markedly suppressed PMHA being a mixed‐type inhibitor (K_i′ = 330 µM), but PMNA was affected by free ATP only slightly. Furthermore, the ATPases substantially differed in their sensitivities to the inhibitors of membrane ATPases, such as orthovanadate, N‐ethylmaleimide and N,N′‐dicyclohexylcarbodiimide. The differences found in the properties of the PMHA and PMNA are discussed in terms of regulation of their activities and their capacity to be involved in cytosolic ion homeostasis in T. viridis cells.     

Measurement of cooling and warming rates in vitrification‐based plant cryopreservation protocols

Cryopreservation protocols include the use of additives and pretreatments aimed to reduce the probability of ice nucleation at all temperatures, mainly through micro‐viscosity increase. Still, there is a risk of ice formation in the temperature region comprised between the equilibrium freezing (T_f) and the glass transition (T_G) temperatures. Consequently, fast cooling and warming, especially in this region, is a must to avoid ice‐derived damage. Vitrification and droplet‐vitrification techniques, frequently used cryopreservation protocols based in fast cooling, were studied, alongside with the corresponding warming procedures. A very fast data acquisition system, able to read very low temperatures, down to that of liquid nitrogen, was employed. Cooling rates, measured between ?20°C and ?120°C, ranged from ca. 5°C s^?1 to 400°C s^?1, while warming rates spanned from ca. 2°C s^?1 to 280°C s^?1, for the different protocols and conditions studied. A wider measuring window (0°C to ?150°C) produced lower rates for all cases. The cooling and warming rates were also related to the survival observed after the different procedures. Those protocols with the faster rates yielded the highest survival percentages. © 2014 American Institute of Chemical Engineers Biotechnol. Prog., 30:1177–1184, 2014