Galvanic Corrosion of Lithium‐Powder‐Based Electrodes

Lithium metal is considered to be the most promising anode for the next generation of batteries if the issues related to safety and low coulombic efficiency can be overcome. It is known that the initial morphology of the lithium metal anode has a great influence on the cycling characteristics of a lithium metal battery (LMB). Lithium‐powder‐based electrodes (Li_p‐electrodes) are reported to diminish the occurrence of high surface area lithium deposits. Usually, ultra‐thin lithium foils (<50 µm) and Li_p‐electrodes are prepared on a copper substrate, thus a metal–metal contact area is generated. The combination of these two metals in the presence of an electrolyte, however, can lead to galvanic corrosion. Herein, the corrosion behavior of Li_p‐electrodes is studied. The porosity of such electrodes leads to a high amount of accessible Cu surface in contact with electrolyte. As a consequence, Li_p‐electrodes aged for 1 week in the electrolyte show spontaneous lithium dissolution near the junction to copper and void formation on the lithium‐powder particles. This corrosion process affects the delivered capacity of Li_p‐electrodes and increases the overvoltage of the lithium electrodissolution process. The occurrence of corrosion at the Cu|Li_p interface raises concerns about the practicality of multi‐metallic component systems for LMBs.     

Introducing Highly Redox‐Active Atomic Centers into Insertion‐Type Electrodes for Lithium‐Ion Batteries

The development of alternative anode materials with higher volumetric and gravimetric capacity allowing for fast delithiation and, even more important, lithiation is crucial for next‐generation lithium‐ion batteries. Herein, the development of a completely new active material is reported, which follows an insertion‐type lithiation mechanism, metal‐doped CeO₂. Remarkably, the introduction of carefully selected dopants, herein exemplified for iron, results in an increase of the achievable capacity by more than 200%, originating from the reduction of the dopant to the metallic state and additional space for the lithium ion insertion due to a significant off‐centering of the dopant atoms in the crystal structure, away from the original Ce site. In addition to the outstanding performance of such materials in high‐power lithium‐ion full‐cells, the selective reduction of the iron dopant under preservation of the crystal structure of the host material is expected to open up a new field of research.     

Ultrahigh‐Energy‐Density Lithium‐Ion Batteries Based on a High‐Capacity Anode and a High‐Voltage Cathode with an Electroconductive Nanoparticle Shell

The combination of high‐capacity anodes and high‐voltage cathodes has garnered a great deal of attention in the pursuit of high‐energy‐density lithium‐ion batteries. As a facile and scalable electrode‐architecture strategy to achieve this goal, a direct one‐pot decoration of high‐capacity silicon (Si) anode materials and of high‐voltage LiCoO₂ (LCO) cathode materials is demonstrated with colloidal nanoparticles composed of electroconductive antimony‐doped tin oxide (ATO). The unusual ATO nanoparticle shells enhance electronic conduction in the LCO and Si electrode materials and mitigate unwanted interfacial side reactions between the electrode materials and liquid electrolytes. The ATO‐coated LCO materials (ATO‐LCO) enable the construction of a high‐mass‐loading cathode and suppress the dissolution of cobalt and the generation of by‐products during high‐voltage cycling. In addition, the ATO‐coated Si (ATO‐Si) anodes exhibit highly stable capacity retention upon cycling. Integration of the high‐voltage ATO‐LCO cathode and high‐capacity ATO‐Si anode into a full cell configuration brings unprecedented improvements in the volumetric energy density and in the cycling performance compared to a commercialized cell system composed of LCO/graphite.     

High Capacity All‐Solid‐State Lithium Batteries Enabled by Pyrite‐Sulfur Composites

As the theoretical limit of intercalation material‐based lithium‐ion batteries is approached, alternative chemistries based on conversion reactions are presently considered. The conversion of sulfur is particularly appealing as it is associated with a theoretical gravimetric energy density up to 2510 Wh kg^?1. In this paper, three different carbon‐iron disulfide‐sulfur (C‐FeS₂‐S) composites are proposed as alternative positive electrode materials for all‐solid‐state lithium‐sulfur batteries. These are synthesized through a facile, low‐cost, single‐step ball‐milling procedure. It is found that the crystalline structure (evaluated by X‐ray diffraction) and the morphology of the composites (evaluated by scanning electron microscopy) are greatly influenced by the FeS₂:S ratio. Li/LiI‐Li₃PS₄/C‐FeS₂‐S solid‐state cells are tested under galvanostatic conditions, while differential capacity plots are used to discuss the peculiar electrochemical features of these novel materials. These cells deliver capacities as high as 1200 mAh g_(FeS2+S)^?1 at the intermediate loading of 1 mg cm^?2 (1.2 mAh cm^?2), and up to 3.55 mAh cm^?2 for active material loadings as high as 5 mg cm^?2 at 20 °C. Such an excellent performance, rarely reported for (sulfur/metal sulfide)‐based, all solid‐state cells, makes these composites highly promising for real application where high positive electrode loadings are required.     

Exploiting Lithium‐Depleted Cathode Materials for Solid‐State Li Metal Batteries

Solid‐state lithium metal batteries (SSLMBs) may become one of the high‐energy density storage devices for the next generation of electric vehicles. High safety and energy density can be achieved by utilizing solid electrolytes and Li metal anodes. Therefore, developing cathode materials which can match with Li metal anode efficiently is indispensable. In SSLMBs, Li metal anodes can afford the majority of active lithium ions, then lithium‐depleted cathode materials can be a competitive candidate to achieve high gravimetric energy density as well as save lithium resources. Li_0.33MnO₂ lithium‐depleted material is chosen, which also has the advantages of low synthesis temperature and low cost (cobalt‐free). Notably, solid‐state electrolyte can greatly alleviate the problem of manganese dissolution in the electrolyte, which is beneficial to improve the cycling stability of the battery. Thus, SSLMBs enable practical applications of lithium‐depleted cathode materials.     

Lithium‐Pretreated Hard Carbon as High‐Performance Sodium‐Ion Battery Anodes

Hard carbon (HC) is the state‐of‐the‐art anode material for sodium‐ion batteries (SIBs). However, its performance has been plagued by the limited initial Coulombic efficiency (ICE) and mediocre rate performance. Here, experimental and theoretical studies are combined to demonstrate the application of lithium‐pretreated HC (LPHC) as high‐performance anode materials for SIBs by manipulating the solid electrolyte interphase in tetraglyme (TEGDME)‐based electrolyte. The LPHC in TEGDME can 1) deliver > 92% ICE and ≈220 mAh g^?1 specific capacity, twice of the capacity (≈100 mAh g^?1) in carbonate electrolyte; 2) achieve > 85% capacity retention over 1000 cycles at 1000 mA g^?1 current density (4 C rate, 1 C = 250 mA g^?1) with a specific capacity of ≈150 mAh g^?1, ≈15 times of the capacity (10 mAh g^?1) in carbonate. The full cell of Na₃V₂(PO₄)₃‐LPHC in TEGDME demonstrated close to theoretical specific capacity of ≈98 mAh g^?1 based on Na₃V₂(PO₄)₃ cathode, ≈2.5 times of the value (≈40 mAh g^?1) with nontreated HC. This work provides new perception on the anode development for SIBs.     

Cascade‐Type Prelithiation Approach for Li‐Ion Capacitors

An industry‐relevant method for pre‐lithiation of lithium‐ion capacitors to balance the first charge irreversibility is demonstrated, which addresses the prime bottleneck for their market integration. Based on a composite positive electrode that integrates pyrene monomers and an insoluble lithiated base, Li₃PO₄, a “cascade‐type” process involving two consecutive irreversible reactions is proposed: i) oxidative electropolymerization of the pyrene moieties releases electrons and protons; ii) protons are captured by Li₃PO₄ and exchanged for a stoichiometric amount of Li⁺ into the electrolyte. (¹H, ¹⁹F, and ³¹P) NMR spectroscopy, operando X‐ray diffraction, and Raman spectroscopy support this mechanism. By decoupling the irreversible source of lithium ions from electrons, the cascade‐type pre‐lithiation allows the simultaneous enhancement of the capacity of the positive electrode, thanks to p‐doping of the resulting polymer. Remarkably, the proton scavenging properties of Li₃PO₄ also boost the polymerization process, which enables a 16% increase in capacity without detrimental effect on power properties and cyclability. Full cells integrating a cheap carbon black based negative electrode, show much‐improved capacity of 17 mAh g^‐1_electrodes (44 F g^‐1_electrodes, 3–4.4 V) and excellent stability over 2200 cycles at 1 A g^‐1. Thanks to its versatile chemistry and flexibility this approach in principle can be applied to any kind of ion‐battery.     

Tethered Molecular Sorbents: Enabling Metal‐Sulfur Battery Cathodes

A rechargeable battery that uses sulfur at the cathode and a metal (e.g., Li, Na, Mg, or Al) at the anode provides perhaps the most promising path to a solid‐state, rechargeable electrochemical storage device capable of high charge storage capacity. It is understood that solubilization in the electrolyte and loss of sulfur in the form of long‐chain lithium polysulfides (Li₂S_x, 2 < x < 8) has hindered development of the most studied of these devices, the rechargeable Li‐S battery. Beginning with density‐functional calculations of the structure and interactions of a generic lithium polysulfide species with nitrile containing molecules, it is shown that it is possible to design nitrile‐rich molecular sorbents that anchor to other components in a sulfur cathode and which exert high‐enough binding affinity to Li₂S_x to limit its loss to the electrolyte. It is found that sorbents based on amines and imidazolium chloride present barriers to dissolution of long‐chain Li₂S_x and that introduction of as little as 2 wt% of these molecules to a physical sulfur‐carbon blend leads to Li‐S battery cathodes that exhibit stable long‐term cycling behaviors at high and low charge/discharge rates.     

Advanced Electrolytes for Fast‐Charging High‐Voltage Lithium‐Ion Batteries in Wide‐Temperature Range

LiNi_xMn_yCo_1?x?yO₂ (NMC) cathode materials with Ni ≥ 0.8 have attracted great interest for high energy‐density lithium‐ion batteries (LIBs) but their practical applications under high charge voltages (e.g., 4.4 V and above) still face significant challenges due to severe capacity fading by the unstable cathode/electrolyte interface. Here, an advanced electrolyte is developed that has a high oxidation potential over 4.9 V and enables NMC811‐based LIBs to achieve excellent cycling stability in 2.5–4.4 V at room temperature and 60 °C, good rate capabilities under fast charging and discharging up to 3C rate (1C = 2.8 mA cm^?2), and superior low‐temperature discharge performance down to ?30 °C with a capacity retention of 85.6% at C/5 rate. It is also demonstrated that the electrode/electrolyte interfaces, not the electrolyte conductivity and viscosity, govern the LIB performance. This work sheds light on a very promising strategy to develop new electrolytes for fast‐charging high‐energy LIBs in a wide‐temperature range.     

Highly Tough,Li‐Metal Compatible Organic–Inorganic Double‐Network Solvate Ionogel

Ionogels are considered promising electrolytes for safe lithium‐ion batteries (LIBs) because of their low flammability, good thermal stability, and wide electrochemical stability window. Conventional ionic liquid‐based ionogels, however, face two main challenges; poor mechanical property and low Li‐ion transfer number. In this work, a novel solvate ionogel electrolyte (SIGE) based on an organic–inorganic double network (DN) is designed and fabricated through nonhydrolytic sol–gel reaction and in situ polymerization processes. The unprecedented SIGE possesses high toughness (bearing the deformation under the pressure of 80 MPa without damage), high Li‐ion transfer number of 0.43, and excellent Li‐metal compatibility. As expected, the LiFePO₄/Li cell using the newly developed SIGE delivers a high capacity retention of 95.2% over 500 cycles, and the average Coulombic efficiency is as high as 99.8%. Moreover, the Ni‐rich LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811)/Li cell based on the modified SIGE achieves a high Coulombic efficiency of 99.4%, which outperforms previous solid/quasi‐solid‐state NCM811‐based LIBs. Interestingly, the SIGE‐based pouch cells are workable under extreme conditions (e.g., severely deforming or clipping into segments). In terms of those unusual features, the as‐obtained SIGE holds great promise for next‐generation flexible and safe energy‐storage devices.