Enhancing Mo:BiVO4 Solar Water Splitting with Patterned Au Nanospheres by Plasmon‐Induced Energy Transfer

Plasmonic metal nanostructures have been extensively investigated to improve the performance of metal oxide photoanodes for photoelectrochemical (PEC) solar water splitting cells. Most of these studies have focused on the effects of those metal nanostructures on enhancing light absorption and enabling direct energy transfer via hot electrons. However, several recent studies have shown that plasmonic metal nanostructures can improve the PEC performance of metal oxide photoanodes via another mechanism known as plasmon‐induced resonant energy transfer (PIRET). However, this PIRET effect has not yet been tested for the molybdenum‐doped bismuth vanadium oxide (Mo:BiVO₄), regarded as one of the best metal oxide photoanode candidates. Here, this study constructs a hybrid Au nanosphere/Mo:BiVO₄ photoanode interwoven in a hexagonal pattern to investigate the PIRET effect on the PEC performance of Mo:BiVO₄. This study finds that the Au nanosphere array not only increases light absorption of the photoanode as expected, but also improves both its charge transport and charge transfer efficiencies via PIRET, as confirmed by time‐correlated single photon counting and transient absorption studies. As a result, incorporating the Au nanosphere array increases the photocurrent density of Mo:BiVO₄ at 1.23 V versus RHE by ≈2.2‐fold (2.83 mA cm^?2).     

(040)‐Crystal Facet Engineering of BiVO4 Plate Photoanodes for Solar Fuel Production

A (040)‐crystal facet engineered BiVO₄ ((040)‐BVO) photoanode is investigated for solar fuel production. The (040)‐BVO photoanode is favorable for improved charge carrier mobility and high photocatalytic active sites for solar light energy conversion. This crystal facet design of the (040)‐BVO photoanode leads to an increase in the energy conversion efficiency for solar fuel production and an enhancement of the oxygen evolution rate. The photocurrent density of the (040)‐BVO photoanode is determined to be 0.94 mA cm^?2 under AM 1.5 G illumination and produces 42.1% of the absorbed photon‐to‐current conversion efficiency at 1.23 V (vs RHE, reversible hydrogen electrode). The enhanced charge separation efficiency and improved charge injection efficiency driven by (040) facet can produce hydrogen with 0.02 mmol h^?1 at 1.23 V. The correlation between the (040)‐BVO photoanode and the solar fuel production is investigated. The results provide a promising approach for the development of solar fuel production using a BiVO₄ photoanode.     

1D Co‐Pi Modified BiVO4/ZnO Junction Cascade for Efficient Photoelectrochemical Water Cleavage

The most important factors dominating solar hydrogen synthesis efficiency include light absorption, charge separation and transport, and surface chemical reactions (charge utilization). In order to tackle these factors, an ordered 1D junction cascade photoelectrode for water splitting, grown via a simple low‐cost solution‐based process and consisting of nanoparticulate BiVO₄ on 1D ZnO rods with cobalt phosphate (Co‐Pi) on the surface is synthesized. Flat‐band measurements reveal the feasibility of charge transfer from BiVO₄ to ZnO, supported by PL measurements and photocurrent observation in the presence of an efficient hole scavenger, which demonstrate that quenching of luminescence of BiVO₄ and enhanced current are caused by electron transfer from BiVO₄ to ZnO. A dramatic cathodic shift in onset potential under both visible and full arc irradiation, coupled with a 12‐fold increase in photocurrent (ca. 3 mA cm^‐2) are observed compared to BiVO₄, resulting in ≈47% IPCE at 410 nm (4% for BiVO₄) with high solar energy conversion efficiency (0.88%). The reasons for these enhancements stem from enhanced light absorption and trapping, in situ rectifying electron transfer from BiVO₄ to ZnO, hole transfer to Co‐Pi for water oxidation, and facilitating electron transport along 1D ZnO.     

PVP Treatment Induced Gradient Oxygen Doping in In2S3 Nanosheet to Boost Solar Water Oxidation of WO3 Nanoarray Photoanode

The photoelectrochemical performance of the WO₃ photoanode is limited by the severe charge recombination in the bulk phase and at the WO₃/electrolyte interface. Herein, In₂S₃ nanosheets are integrated onto the surface of the WO₃ nanowall array photoanode, followed by a facile polyvinylpyrrolidone (PVP) solution treatment. The PVP treatment results in sulfur vacancies and a gradient oxygen doping into In₂S₃ from surface to interior, which induces the formation of a gradient energy band distribution. The gradient band structured In₂S₃ and type II band alignment at the WO₃/In₂S₃ interface simultaneously create a channel that favors photogenerated electrons to migrate from the surface to the conductive substrate, thereby suppressing bulk carrier recombination. Meanwhile, the sulfur vacancies and oxygen doping contribute to increased charge carrier concentration, prolonged carrier lifetime, more active sites, and small interfacial transfer impedance. As a consequence, the PVP treated WO₃/In₂S₃ heterostructure photoanode exhibits a significantly enhanced photocurrent of 1.61 mA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE) and negative onset potential of 0.02 V versus RHE.     

Efficient BiVO4 Photoanode with an Excellent Hole Transport Layer of CuSCN for Solar Water Oxidation

Bismuth vanadate (BiVO₄) is reported as a key material in photoelectrocatalysis owing to high theoretical efficiency, relatively narrow band gap of 2.4 eV, and favorable conduction band edge position for hydrogen evolution. However, the sluggish hole transport dynamics lead to slow photogenerated charge separation and transport efficiencies, which result in charge recombination due to aggregation. Herein, a novel hole transport layer of copper(I) thiocyanate (CuSCN) with the aim of significantly enhancing the efficiency of charge transport and stability of BiVO₄ photoanodes is reported. The introduction of the hole transport layer could provide an appropriate intermediate energy level for photogenerated hole transfer and avoid charge recombination and trapping. After a photoassisted electrodeposition process of NiCoFe-B_i catalysis, the obtained photoanode achieves a photocurrent density of 5.6 mA cm⁻² at 1.23 V versus reversible hydrogen electrode under AM 1.5 G simulated solar radiation, and an applied bias photon to current efficiency of 2.31%. With the CuSCN layer, BiVO₄ photoanode presented impressive stable photocurrent during 50 h continuous illumination. Meanwhile, the unbiased tandem device of the NiCoFe-B_i/CuSCN/BiVO₄ photoanode and the Si solar cell exhibit a solar-to-hydrogen efficiency of 5.75% and excellent stability for 14 h.     

Overcoming Charge Collection Limitation at Solid/Liquid Interface by a Controllable Crystal Deficient Overlayer

Bulk and surface charge recombination of photoelectrode are two key processes that significantly hinder solar‐to‐fuel conversion of photoelectrochemical cell (PEC). In this study, the function of a “crystal‐deficient” overlayer is unveiled, which outperforms a traditionally used amorphous or crystalline overlayer in PEC water splitting by exhibiting a high conductivity and large electron diffusion length to enable unlimited electron collection. The optimized ≈2.5 nm thickness of the “crystal‐deficient” shell results in a depletion layer with a width of 3 nm, which overcomes the flat band limitation of the photovoltage and increases the light absorptivity in the wavelength range from 300 to 420 nm. In addition, a 50‐fold increase in the conductivity yields a one‐order‐of‐magnitude increase in the diffusion length of an electron (L_n )(≈20 μm), allowing for unlimited electron collection in the 1.9 μm TiO₂ nanowire array with the “crystal‐deficient” shell. The controllable “crystal‐deficient” overlayer in rutile TiO₂ nanowires photoanode achieves a photocurrent density greater than 2.0 mA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE), a 1.18% applied bias photon‐to‐current efficiency at 0.49 V versus RHE, a faradaic efficiency greater than 93.5% at 0.6 V versus Pt under air mass 1.5G simulated solar light illumination (100 mW cm^?2).     

Carbon Nitride/Reduced Graphene Oxide Film with Enhanced Electron Diffusion Length: An Efficient Photo‐Electrochemical Cell for Hydrogen Generation

Polymeric carbon nitride (CN) has emerged as a promising semiconductor for energy‐related applications. However, its utilization in photo‐electrochemical cells is still very limited owing to poor electron–hole separation efficiency, short electron diffusion length, and low absorption coefficient. Here the synthesis of a highly porous carbon nitride/reduced graphene oxide (CN‐rGO) film with good photo‐electrochemical properties is reported. The CN‐rGO film exhibits long electron diffusion length and high electrochemical active surface area, good charge separation, and enhanced light‐harvesting properties. The film displays a 20‐fold enhancement of photocurrent density over pristine CN, reaching up to 75 µA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE) in an alkaline solution, as well as stability over a wide pH range. Photocurrent measurements with a hole scavenger reveal a photocurrent density of 660 µA cm^?2 at 1.23 V versus RHE and a quantum efficiency of 60% at 400 nm, resulting in the production of 0.8 mol h^?1 g^?1 of hydrogen. The substantial photo‐electrochemical activity enhancement and hydrogen production together with the low price, high electrochemical surface area, long electron diffusion length, stability under harsh condition, and tunable photophysical properties of CN materials open many possibilities for their utilization in (photo)electrochemical and electronic devices.     

MOF‐Based Transparent Passivation Layer Modified ZnO Nanorod Arrays for Enhanced Photo‐Electrochemical Water Splitting

This study introduces zeolitic imidazolate framework‐8 (ZIF‐8) as the first metal‐organic framework based transparent surface passivation layer for photo‐electrochemical (PEC) water splitting. A significant enhancement for PEC water oxidation is demonstrated based on the in situ seamless coating of ZIF‐8 surface passivation layer on Ni foam (NF) supported ZnO nanorod arrays photoanode. The PEC performance is improved by optimizing the ZIF‐8 thickness and by grafting Ni(OH)₂ nanosheets as synergetic co‐catalyst. With respect to ZnO/NF, the optimized Ni(OH)₂/ZIF‐8/ZnO/NF photoanode exhibits a two times larger photocurrent density of 1.95 mA cm^?2 and also a two times larger incident photon to current conversion efficiency of 40.05% (350 nm) at 1.23 V versus RHE (V_RHE) under AM 1.5 G. The synergetic surface passivation and the co‐catalyst modification contribute to prolonging the charge lifetime, to promoting the charge transfer, and to decreasing the overpotential for water oxidation.     

Constructing a AZO/TiO2 Core/Shell Nanocone Array with Uniformly Dispersed Au NPs for Enhancing Photoelectrochemical Water Splitting

Constructing core/shell nanostructures with optimal structure and composition could maximize the solar light utilization. Here, using an Al nanocone array as a substrate, a well‐defined regular array of AZO/TiO₂ core/shell nanocones with uniformly dispersed Au nanoparticles (AZO/TiO₂/Au NCA) is successfully realized through three sequential steps of atomic layer deposition, physical vapor deposition, and annealing processes. By tuning the structural and compositional parameters, the advantages of light trapping and short carrier diffusion from the core/shell nanocone array, as well as the surface plasmon resonance and catalytic effects from the Au nanoparticles can be maximally utilized. Accordingly, a remarkable photoelectrochemical (PEC) performance can be acquired and the photocurrent density of the AZO/TiO₂/Au NCA electrode reaches up to 1.1 mA cm^?2 at 1.23 V, versus reversible hydrogen electrode (RHE) under simulated sunlight illumination, which is five times that of a flat AZO/TiO₂ electrode (0.22 mA cm^?2). Moreover, the photoconversion of the AZO/TiO₂/Au NCA electrode approaches 0.73% at 0.21 V versus RHE, which is one of the highest values with the lowest applied bias ever reported in Au/TiO₂ PEC composites. These results demonstrate a feasible route toward the scalable fabrication of well‐modulated core/shell nanostructures and can be easily applied to other metal/semiconductor composites for high‐performance PEC.     

Boosting the Performance of WO3/n‐Si Heterostructures for Photoelectrochemical Water Splitting: from the Role of Si to Interface Engineering

Metal oxide/Si heterostructures make up an exciting design route to high‐performance electrodes for photoelectrochemical (PEC) water splitting. By monochromatic light sources, contributions of the individual layers in WO₃/n‐Si heterostructures are untangled. It shows that band bending near the WO₃/n‐Si interface is instrumental in charge separation and transport, and in generating a photovoltage that drives the PEC process. A thin metal layer inserted at the WO₃/n‐Si interface helps in establishing the relation among the band bending depth, the photovoltage, and the PEC activity. This discovery breaks with the dominant Z‐scheme design idea, which focuses on increasing the conductivity of an interface layer to facilitate charge transport, but ignores the potential profile around the interface. Based on the analysis, a high‐work‐function metal is predicted to provide the best interface layer in WO₃/n‐Si heterojunctions. Indeed, the fabricated WO₃/Pt/n‐Si photoelectrodes exhibit a 2 times higher photocurrent density at 1.23 V versus reversible hydrogen electrode (RHE) and a 10 times enhancement at 1.6 V versus RHE compared to WO₃/n‐Si. Here, it is essential that the native SiO₂ layer at the interface between Si and the metal is kept in order to prevent Fermi level pinning in the Schottky contact between the Si and the metal.     

Enhancing Low‐Bias Performance of Hematite Photoanodes for Solar Water Splitting by Simultaneous Reduction of Bulk,Interface, and Surface Recombination Pathways

For a hematite (α‐Fe₂O₃) photoanode, multiple electron/hole recombination pathways occurring in the bulk, interfaces, and surfaces largely limit its low‐bias performance (low photocurrent density at low‐bias potential) for photoelectrochemical water splitting. Here, a facile and rapid three‐step approach is reported to simultaneously reduce these recombinations for hematite nanorods (NRs) array photoanode, leading to a greatly improved photocurrent density at low bias potential. First, flame‐doping enables high concentration of Ti doping without hampering the morphology and surface properties of the hematite NRs, which reduces both the bulk and surface recombinations effectively. Second, the addition of a dense‐layer between the hematite NRs and fluorine‐doped SnO₂ substrate effectively reduces the interfacial recombination by suppressing the electron back‐injection into electrolyte. Finally, the sequential oxalic acid etching and FeOOH deposition improves both the interface quality between FeOOH electrocatalyst and hematite NRs and the surface catalytic activity. Significantly, the combination of flame‐doping, dense‐layer deposition, surface etching, and electrocatalyst deposition effectively reduces the multiple electron/hole recombination pathways in a hematite NRs photoanode, which decreases the photocurrent onset potential from 1.02 V _RHE to 0.64 V_RHE, a reduction of 380 mV.     

A Delaminated Defect‐Rich ZrO2 Hierarchical Nanowire Photocathode for Efficient Photoelectrochemical Hydrogen Evolution

An efficient way to combat the energy crisis and the greenhouse gas effect of fossil fuels is the production of hydrogen fuel from solar‐driven water splitting reaction. Here, this study presents a p‐type ZrO₂ nanoplate‐decorated ZrO₂ nanowire photocathode with a high photoconversion efficiency that makes it potentially viable for commercial solar H₂ production. The composition of oxygen vacancy defects, low charge carrier transport property, and high specific surface area of these as‐grown hierarchical nanowires are further improved by an hydrofluoric acid (HF) treatment, which causes partial delamination and produces a thin amorphous ZrO₂ layer on the surface of the as‐grown nanostructured film. The presence of different types of oxygen vacancies (neutral, singly charged, and doubly charged defects) and their compositional correlation to the Zr^x+ oxidation states (4 > x > 2) are found to affect the charge transfer process, the p‐type conductivity, and the photocatalytic activity of the ZrO₂ nanostructured film. The resulting photocathode provides the highest overall photocurrent (?42.3 mA cm^?2 at 0 V vs reversible hydrogen electrode (RHE)) among all the photocathodes reported to date, and an outstanding 3.1% half‐cell solar‐to‐hydrogen conversion efficiency with a Faradaic efficiency of 97.8%. Even more remarkable is that the majority of the photocurrent (69%) is produced in the visible light region.     

Decoupling Photocurrent Loss Mechanisms in Photovoltaic Cells Using Complementary Measurements of Exciton Diffusion

Significant work has been directed at measuring the exciton diffusion length (L_D) in organic semiconductors due to its significance in determining the performance of photovoltaic cells. Several techniques have been developed to measure L_D, often probing photoluminescence or charge carrier generation. Interestingly, in this study it is shown that when different techniques are compared, both the diffusive behavior of the exciton and active carrier recombination loss pathways can be decoupled. Here, a planar heterojunction device based on the donor–acceptor pairing of boron subphthalocyanine chloride‐C₆₀ is examined using photoluminescence quenching, photovoltage‐, and photocurrent‐based L_D measurement techniques. Photovoltage yields the device relevant L_D of both active materials as a function of forward bias subject to geminate recombination losses. These values are used to accurately predict the photocurrent as a function of voltage, suggesting geminate recombination is the dominant mechanism responsible for photocurrent loss. By combining these measurements with photocurrent and photoluminescence quenching, the intrinsic L_D, as well as the voltage‐dependent charge transfer state dissociation and charge collection efficiencies are quantitatively determined. The results of this work provide a method to decouple all relevant loss pathways during photoconversion, and establish the factors that can limit the performance of excitonic photovoltaic cells.     

3D Porous Pyramid Heterostructure Array Realizing Efficient Photo‐Electrochemical Performance

Direct photo‐electrochemical (PEC) water splitting is of great practical interest for developing a sustainable energy systems, but remains a big challenge owing to sluggish charge separation, low efficiency, and poor stability. Herein, a 3D porous In₂O₃/In₂S₃ pyramid heterostructure array on a fluorine‐doped tin oxide substrate is fabricated by an ion exchange–induced synthesis strategy. Based on the synergistic structural and electronic modulations from density functional theory calculations and experimental observations, 3D porous In₂O₃/In₂S₃ photoanode by the protective layer delivers a low onset potential of ≈0.02 V versus reversible hydrogen electrode (RHE), the highest photocurrent density of 8.2 mA cm^?2 at 1.23 V versus RHE among all the In₂S₃ photoanodes reported to date, an incident photon‐to‐current efficiency of 76% at 400 nm, and high stability over 20 h for PEC water splitting are reported. This work provides an alternative promising prototype for the design and construction of novel heterostructures in robust PEC water splitting applications.     

Charge Transport and Recombination in Low‐Bandgap Bulk Heterojunction Solar Cell using Bis‐adduct Fullerene

Charge transport and recombination are studied for organic solar cells fabricated using blends of polymer poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,5′‐diyl] (Si‐PCPDTBT) with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (mono‐PCBM) and the bis‐adduct analogue of mono‐PCBM (bis‐PCBM). The photocurrent of Si‐PCPDTBT:bis‐PCBM devices shows a strong square root dependence on the effective applied voltage. From the relationship between the photocurrent and the light intensity, we found that the square‐root dependence of the photocurrent is governed by the mobility‐lifetime (μτ) product of charge carriers while space‐charge field effects are insignificant. The fill factor (FF) and short circuit current density (J_sc) of bis‐PCBM solar cells show a considerable increase with temperature as compared to mono‐PCBM solar cells. SCLC analysis of single carrier devices proofs that the mobility of both electrons and holes is significantly lowered when replacing mono‐PCBM with bis‐PCBM. The increased recombination in Si‐PCPDTBT:bis‐PCBM solar cells is therefore attributed to the low carrier mobilities, as the transient photovoltage measurements show that the carrier lifetime of devices are not significantly altered by using bis‐PCBM instead of mono‐PCBM.     

New Insights into Defect‐Mediated Heterostructures for Photoelectrochemical Water Splitting

Understanding the interfacial electronic structures of heterojunctions, a challenging undertaking, is extremely important to the design of photoelectrodes for efficient water splitting. The heterostructured interfaces in terms of crystal defects at the atomic‐level exemplified by TiO₂/BiVO₄ are studied. Results from both experimental observations and theoretical calculations clearly confirm the spontaneous formation of defective interfaces in the heterostructures. TiO₂/BiVO₄ junction with engineered interfacial defects can efficiently increase the carrier density and extend the lifetime of electrons. The inherent phenomenon of defective electronic structures in different heterostructures creates a significant impact on their photoelectrochemical performance. The synergetic effect between defect‐mediated mechanism and organic quantum dots sensitization yields significantly increased photoconversion efficiency, which is even superior to that of common metal sulfide sensitized ones. This result demonstrates an approach worthy for the design and fabrication of defect‐mediated heterostructures for water splitting, without utilizing harmful metal sulfides. Moreover, new insights into the influence of intrinsic defects on the interfacial charge transfer process between two different semiconductors for energy‐related applications have also been provided.     

Contact‐Induced Mechanisms in Organic Photovoltaics: A Steady‐State and Transient Study

The role of the contacts in thin‐film, blended heterojunctions (<100 nm thick) organic photovoltaics is explored, specifically considering concepts of carrier selectivity, injection, and extraction efficiency, relative to recombination. Contact effects are investigated by comparing two hole‐collecting interlayers: a phosphonic acid monolayer on indium tin oxide (ITO) and a nickel oxide thin film. The interlayers have equivalent work functions (≈5.4 eV) but widely variant energy band offsets relative to the lowest unoccupied molecular orbital of the acceptor (electron blocking versus not), which are coupled to large differences in carrier density. Trends in open‐circuit voltages (V_OC) as a function of light intensity and temperature are compared and it is concluded that the dominant mechanism limiting V_OC for high density of states contacts is free carrier injection, not surface recombination or extraction barriers. Transient photocurrent decay measurements confirm excess reinjected carriers decrease the extraction efficiency via increased recombination and decrease free carrier lifetime, even at high internal electric fields, due to space charge accumulation. These results demonstrate that the energetics and injection dynamics of the interface between interlayers and high carrier density electrodes (typically ITO and metals) must be considered with fabrication and processing of interlayers, in addition to possible carrier selectivity and the interface with the active layer.     

Moisture‐Assisted Preparation of Compact GaN:ZnO Photoanode Toward Efficient Photoelectrochemical Water Oxidation

Developing strategies that can promote charge transportation in photodevices is crucial for achieving high solar energy conversion efficiency. Herein a moisture‐assisted nitridation approach is presented for the fabrication of efficient gallium‐zinc oxynitride (GaN:ZnO) photoanode with compact structure to facilitate the charge transportation. With moisture‐assisted nitridation, the charge separation efficiency and injection efficiency obtained on GaN:ZnO photoanode are significantly enhanced. Correspondingly, the photocurrent at 1.23 V vs reversible hydrogen electrode (RHE) has 18 folds improvement compared with that prepared without moisture assistance. Furthermore, via treating with HCl acid and modification with cobalt phosphate (CoPi) as a cocatalyst, state‐of‐the‐art photocurrent over 2.0 mA cm^?2 is achieved on independent GaN:ZnO photoanode when bias is higher than 1.4 V vs RHE. To the best of our knowledge, this is the first paradigm of moisture‐assisted preparing oxynitride‐based photoanode. The participation of moisture is found to improve the interconnection between adjacent GaN:ZnO nanoparticles as well as that between the GaN:ZnO film and the underlying substrate. Moreover, the volatilization of Zn can be substantially suppressed due to the modulation of reaction pathway by moisture. These two factors are confirmed to be the main reasons for the enhanced charge transportation and PEC performance obtained on GaN:ZnO photoanode.     

Enhancing Charge Carrier Lifetime in Metal Oxide Photoelectrodes through Mild Hydrogen Treatment

Widespread application of solar water splitting for energy conversion is largely dependent on the progress in developing not only efficient but also cheap and scalable photoelectrodes. Metal oxides, which can be deposited with scalable techniques and are relatively cheap, are particularly interesting, but high efficiency is still hindered by the poor carrier transport properties (i.e., carrier mobility and lifetime). Here, a mild hydrogen treatment is introduced to bismuth vanadate (BiVO₄), which is one of the most promising metal oxide photoelectrodes, as a method to overcome the carrier transport limitations. Time‐resolved microwave and terahertz conductivity measurements reveal more than twofold enhancement of the carrier lifetime for the hydrogen‐treated BiVO₄, without significantly affecting the carrier mobility. This is in contrast to the case of tungsten‐doped BiVO₄, although hydrogen is also a donor type dopant in BiVO₄. The enhancement in carrier lifetime is found to be caused by significant reduction of trap‐assisted recombination, either via passivation or reduction of deep trap states related to vanadium antisite on bismuth or vanadium interstitials according to density functional theory calculations. Overall, these findings provide further insights on the interplay between defect modulation and carrier transport in metal oxides, which benefit the development of low‐cost, highly‐efficient solar energy conversion devices.     

Scalable Triple Cation Mixed Halide Perovskite–BiVO4 Tandems for Bias‐Free Water Splitting

Strong interest exists in the development of organic–inorganic lead halide perovskite photovoltaics and of photoelectrochemical (PEC) tandem absorber systems for solar fuel production. However, their scalability and durability have long been limiting factors. In this work, it is revealed how both fields can be seamlessly merged together, to obtain scalable, bias‐free solar water splitting tandem devices. For this purpose, state‐of‐the‐art cesium formamidinium methylammonium (CsFAMA) triple cation mixed halide perovskite photovoltaic cells with a nickel oxide (NiO_x) hole transport layer are employed to produce Field's metal‐epoxy encapsulated photocathodes. Their stability (up to 7 h), photocurrent density (–12.1 ± 0.3 mA cm^?2 at 0 V versus reversible hydrogen electrode, RHE), and reproducibility enable a matching combination with robust BiVO₄ photoanodes, resulting in 0.25 cm² PEC tandems with an excellent stability of up to 20 h and a bias‐free solar‐to‐hydrogen efficiency of 0.35 ± 0.14%. The high reliability of the fabrication procedures allows scaling of the devices up to 10 cm², with a slight decrease in bias‐free photocurrent density from 0.39 ± 0.15 to 0.23 ± 0.10 mA cm^?2 due to an increasing series resistance. To characterize these devices, a versatile 3D‐printed PEC cell is also developed.