Green‐Solvent‐Processed All‐Polymer Solar Cells Containing a Perylene Diimide‐Based Acceptor with an Efficiency over 6.5%

To realize high power conversion efficiencies (PCEs) in green‐solvent‐processed all‐polymer solar cells (All‐PSCs), a long alkyl chain modified perylene diimide (PDI)‐based polymer acceptor PPDIODT with superior solubility in nonhalogenated solvents is synthesized. A properly matched PBDT‐TS1 is selected as the polymer donor due to the red‐shifted light absorption and low‐lying energy level in order to achieve the complementary absorption spectrum and matched energy level between polymer donor and polymer acceptor. By utilizing anisole as the processing solvent, an optimal efficiency of 5.43% is realized in PBDT‐TS1/PPDIODT‐based All‐PSC with conventional configuration, which is comparable with that of All‐PSCs processed by the widely used binary solvent. Due to the utilization of an inverted device configuration, the PCE is further increased to over 6.5% efficiency. Notably, the best‐performing PCE of 6.58% is the highest value for All‐PSCs employing PDI‐based polymer acceptors and green‐solvent‐processed All‐PSCs. The excellent photovoltaic performance is mainly attributed to a favorable vertical phase distribution, a higher exciton dissociation efficiency (P_diss) in the blend film, and a higher electrode carrier collection efficiency. Overall, the combination of rational molecular designing, material selection, and device engineering will motivate the efficiency breakthrough in green‐solvent‐processed All‐PSCs.     

Benzotriazole-Based Polymer Acceptor for High-Efficiency All-Polymer Solar Cells with High Photocurrent and Low Voltage Loss

The power conversion efficiencies (PCEs) of all-polymer solar cells (all-PSCs) have already exceeded 17%. However, the limited absorption range of an all-polymer system results in significantly reduced short-circuit current density (J_sc), which eventually influences the PCE improvement. To broaden the light absorption of polymer acceptors, herein, benzotriazole is introduced in the core unit of small molecule acceptors and thus two narrow-bandgap polymer acceptors named PTz-BO and PTz-C11 featuring the same molecular backbone and different side-chain length are synthesized. Compared with PTz-C11, the PTz-BO based-all PSCs deliver a slightly reduced J_sc, a large open-circuit voltage (V_oc) and a low voltage loss below 0.50 V. Moreover, ternary all-PSCs are constructed by introducing PTz-C11 as a guest component. Benefiting from the reduced recombination, improved exciton generation and dissociation, and balanced charge transport, a high efficiency of 16.58% is obtained for the ternary all-PSCs, with a high J_sc over 25 mA cm⁻² without sacrificing the V_oc. Such result represents the highest efficiency reported for benzotriazole-based all-PSCs in the literature thus far. This work demonstrates the great potential of benzotriazole for the synthesis of efficient narrow-bandgap polymer acceptors.     

Reduced Energy Loss Enabled by a Chlorinated Thiophene‐Fused Ending‐Group Small Molecular Acceptor for Efficient Nonfullerene Organic Solar Cells with 13.6% Efficiency

Generally, highly efficient organic solar cells require both a high open‐circuit voltage (V_OC) and a high short‐circuit current density (J_SC). Reducing the energy loss (E_loss) is an effective way to achieve a high V_OC without compromising the photocurrent, which is ideal for enhancing the power conversion efficiencies (PCEs). Herein, a new chlorinated nonfullerene acceptor (ITC‐2Cl) with chlorinated thiophene‐fused end groups is developed. In comparison with the unchlorinated counterpart (ITCPTC), the introduction of Cl improves not only the electronic properties by redshifting the absorption spectra and deepening the lowest unoccupied molecular orbital energy levels, but also the molecular packing and thus thin‐film morphology. The PM6:ITC‐2Cl‐based device yields a significantly higher PCE (13.6%) with a lower E_loss (0.67 eV) than the ITCPTC‐based device (PCE of 12.3% with E_loss of 0.70 eV). More importantly, compared to the archetypal nonfullerene acceptors such as IT‐4F (PCE of 12.9% with E_loss of 0.73 eV) and IT‐4Cl (PCE of 12.7% with E_loss of 0.76 eV), the ITC‐2Cl‐based device shows a higher PCE and a lower E_loss. These results demonstrate that the chlorinated thiophene‐fused end group is a promising candidate for a high‐performance nonfullerene acceptors with low energy loss.     

Ternary Blended Fullerene‐Free Polymer Solar Cells with 16.5% Efficiency Enabled with a Higher‐LUMO‐Level Acceptor to Improve Film Morphology

Ternary approaches to solar cell design utilizing a small bandgap nonfullerene acceptor as the near infrared absorber to increase the short‐circuit current density always decreases the open‐circuit voltage. Herein, a highly efficient polymer solar cell with an impressive efficiency of 16.28 ± 0.20% enabled by an effective voltage‐increased ternary blended fullerene‐free material approach is reported. In this approach, the structural similarity between the host and the higher‐LUMO‐level guest enables the two acceptors to be synergized, obtaining increased open‐circuit voltage and fill factor and a small increase of short‐circuit current density. The same beneficial effects are demonstrated by using two host binary systems. The homogeneous fine film morphologies and the π–π stacking patterns of the host blend are well maintained, while larger donor and acceptor phases and increased lamellar crystallinity, increased charge mobilities, and reduced monomolecular recombination can be achieved upon addition of the guest nonfullerene acceptor. The increased charge mobilities and reduced monomolecular recombination not only contribute to the improved fill factor but also enable the best devices to be fabricated with a relatively thicker ternary blended active layer (110 vs 100 nm). This, combined with the absorption from the added guest acceptor, contribute to the increased short‐circuit current.     

Roll‐to‐Roll Printed Large‐Area All‐Polymer Solar Cells with 5% Efficiency Based on a Low Crystallinity Conjugated Polymer Blend

The challenge of continuous printing in high‐efficiency large‐area organic solar cells is a key limiting factor for their widespread adoption. A materials design concept for achieving large‐area, solution‐coated all‐polymer bulk heterojunction solar cells with stable phase separation morphology between the donor and acceptor is presented. The key concept lies in inhibiting strong crystallization of donor and acceptor polymers, thus forming intermixed, low crystallinity, and mostly amorphous blends. Based on experiments using donors and acceptors with different degree of crystallinity, the results show that microphase separated donor and acceptor domain sizes are inversely proportional to the crystallinity of the conjugated polymers. This methodology of using low crystallinity donors and acceptors has the added benefit of forming a consistent and robust morphology that is insensitive to different processing conditions, allowing one to easily scale up the printing process from a small‐scale solution shearing coater to a large‐scale continuous roll‐to‐roll (R2R) printer. Large‐area all‐polymer solar cells are continuously roll‐to‐roll slot die printed with power conversion efficiencies of 5%, with combined cell area up to 10 cm². This is among the highest efficiencies realized with R2R‐coated active layer organic materials on flexible substrate.     

Solution‐Processed Polymer Solar Cells with over 17% Efficiency Enabled by an Iridium Complexation Approach

The commercially available PM6 as donor materials are used widely in highly efficient nonfullerene polymer solar cells (PSCs). In this work, different concentrations of iridium (Ir) complexes (0, 0.5, 1, 2.5, and 5 mol%) are incorporated carefully into the polymer conjugated backbone of PM6 (PM6‐Ir0), and a set of π‐conjugated polymer donors (named PM6‐Ir0.5, PM6‐Ir1, PM6‐Ir2.5, and PM6‐Ir5) are synthesized and characterized. It is demonstrated that the approach can rationally modify the molecular aggregations of polymer donors, effectively controlling the corresponding blend morphology and physical mechanisms, and finally improve the photovoltaic performance of the PM6‐Irx‐based PSCs. Among them, the best device based on PM6‐Ir1:Y6 (1:1.2, w/w) exhibits outstanding power conversion efficiencies (PCEs) of 17.24% tested at Wuhan University and 17.32% tested at Institute of Chemistry, Chinese Academy of Sciences as well as a certified PCE of 16.70%, which are much higher than that of the control device based on the PM6‐Ir0:Y6 blend (15.39%). This work affords an effective approach for further break through the reported champion PCE of the binary PSCs.     

Design of Cyanovinylene‐Containing Polymer Acceptors with Large Dipole Moment Change for Efficient Charge Generation in High‐Performance All‐Polymer Solar Cells

Designing polymers that facilitate exciton dissociation and charge transport is critical for the production of highly efficient all‐polymer solar cells (all‐PSCs). Here, the development of a new class of high‐performance naphthalenediimide (NDI)‐based polymers with large dipole moment change (Δµ_ge) and delocalized lowest unoccupied molecular orbital (LUMO) as electron acceptors for all‐PSCs is reported. A series of NDI‐based copolymers incorporating electron‐withdrawing cyanovinylene groups into the backbone (PNDITCVT‐R) is designed and synthesized with 2‐hexyldecyl (R = HD) and 2‐octyldodecyl (R = OD) side chains. Density functional theory calculations reveal an enhancement in Δµ_ge and delocalization of the LUMO upon the incorporation of cyanovinylene groups. All‐PSCs fabricated from these new NDI‐based polymer acceptors exhibit outstanding power conversion efficiencies (7.4%) and high fill factors (65%), which is attributed to efficient exciton dissociation, well‐balanced charge transport, and suppressed monomolecular recombination. Morphological studies by grazing X‐ray scattering and resonant soft X‐ray scattering measurements show the blend films containing polymer donor and PNDITCVT‐R acceptors to exhibit favorable face‐on orientation and well‐mixed morphology with small domain spacing (30–40 nm).     

High‐Performance and Stable All‐Polymer Solar Cells Using Donor and Acceptor Polymers with Complementary Absorption

To explore the advantages of emerging all‐polymer solar cells (all‐PSCs), growing efforts have been devoted to developing matched donor and acceptor polymers to outperform fullerene‐based PSCs. In this work, a detailed characterization and comparison of all‐PSCs using a set of donor and acceptor polymers with both conventional and inverted device structures is performed. A simple method to quantify the actual composition and light harvesting contributions from the individual donor and acceptor is described. Detailed study on the exciton dissociation and charge recombination is carried out by a set of measurements to understand the photocurrent loss. It is unraveled that fine‐tuned crystallinity of the acceptor, matched donor and acceptor with complementary absorption and desired energy levels, and device architecture engineering can synergistically boost the performance of all‐PSCs. As expected, the PBDTTS‐FTAZ:PNDI‐T10 all‐PSC attains a high and stable power conversion efficiency of 6.9% without obvious efficiency decay in 60 d. This work demonstrates that PNDI‐T10 can be a potential alternative acceptor polymer to the widely used acceptor N2200 for high‐performance and stable all‐PSCs.     

Thieno[3,4‐c]Pyrrole‐4,6‐Dione‐Based Polymer Acceptors for High Open‐Circuit Voltage All‐Polymer Solar Cells

While polymer acceptors are promising fullerene alternatives in the fabrication of efficient bulk heterojunction (BHJ) solar cells, the range of efficient material systems relevant to the “all‐polymer” BHJ concept remains narrow, and currently limits the perspectives to meet the 10% efficiency threshold in all‐polymer solar cells. This report examines two polymer acceptor analogs composed of thieno[3,4‐c ]pyrrole‐4,6‐dione (TPD) and 3,4‐difluorothiophene ([2F]T) motifs, and their BHJ solar cell performance pattern with a low‐bandgap polymer donor commonly used with fullerenes (PBDT‐TS1; taken as a model system). In this material set, the introduction of a third electron‐deficient motif, namely 2,1,3‐benzothiadiazole (BT), is shown to (i) significantly narrow the optical gap (E _opt) of the corresponding polymer (by ≈0.2 eV) and (ii) improve the electron mobility of the polymer by over two orders of magnitude in BHJ solar cells. In turn, the narrow‐gap P2TPDBT[2F]T analog (E _opt = 1.7 eV) used as fullerene alternative yields high open‐circuit voltages (V _OC) of ≈1.0 V, notable short‐circuit current values (J _SC) of ≈11.0 mA cm⁻², and power conversion efficiencies (PCEs) nearing 5% in all‐polymer BHJ solar cells. P2TPDBT[2F]T paves the way to a new, promising class of polymer acceptor candidates.     

Improved Tandem All‐Polymer Solar Cells Performance by Using Spectrally Matched Subcells

All‐polymer solar cells (all‐PSCs) are attractive as alternatives to fabricate thermally and mechanically stable solar cells, especially with recent improvements in their power conversion efficiency (PCE). In this work, efficient all‐PSCs with near‐infrared response (up to 850 nm) are developed using newly designed regioregular polymer donors with relatively narrow optical gap. These all‐PSCs systems achieve PCEs up to 6.0% after incorporating fluorine into the polymer backbone. More importantly, these polymers exhibit absorbance that is complementary to previously reported wide bandgap polymer donors. Thus, the superior properties of the newly designed polymers afford opportunities to fabricate the first spectrally matched all‐polymer tandem solar cells with high performance. A PCE of 8.3% is then demonstrated which is the highest efficiency so far for all‐polymer tandem solar cells. The design of narrow bandgap polymers provides new directions to enhance the PCE of emerging single‐junction and tandem all polymer solar cells.     

8.0% Efficient All‐Polymer Solar Cells with High Photovoltage of 1.1 V and Internal Quantum Efficiency near Unity

In very recent years, growing efforts have been devoted to the development of all‐polymer solar cells (all‐PSCs). One of the advantages of all‐PSCs over the fullerene‐based PSCs is the versatile design of both donor and acceptor polymers which allows the optimization of energy levels to maximize the open‐circuit voltage (V_oc). However, there is no successful example of all‐PSCs with both high V_oc over 1 V and high power conversion efficiency (PCE) up to 8% reported so far. In this work, a combination of a donor polymer poly[4,8‐bis(5‐(2‐octylthio)thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl‐alt‐(5‐(2‐ethylhexyl)‐4H‐thieno[3,4‐c]pyrrole‐4,6(5H)‐dione)‐1,3‐diyl] (PBDTS‐TPD) with a low‐lying highest occupied molecular orbital level and an acceptor polymer poly[[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐thiophene‐2,5‐diyl] (PNDI‐T) with a high‐lying lowest unoccupied molecular orbital level is used, realizing high‐performance all‐PSCs with simultaneously high V_oc of 1.1 V and high PCE of 8.0%, and surpassing the performance of the corresponding PC₇₁BM‐based PSCs. The PBDTS‐TPD:PNDI‐T all‐PSCs achieve a maximum internal quantum efficiency of 95% at 450 nm, which reveals that almost all the absorbed photons can be converted into free charges and collected by electrodes. This work demonstrates the advantages of all‐PSCs by incorporating proper donor and acceptor polymers to boost both V_oc and PCEs.     

Controlling Molecular Orientation of Naphthalenediimide‐Based Polymer Acceptors for High Performance All‐Polymer Solar Cells

Molecular orientation, with respect to donor/acceptor interface and electrodes, plays a critical role in determining the performance of all‐polymer solar cells (all‐PSCs), but is often difficult to rationally control. Here, an effective approach for tuning the molecular crystallinity and orientation of naphthalenediimide‐bithiophene‐based n‐type polymers (P(NDI2HD‐T2)) by controlling their number average molecular weights (M_n) is reported. A series of P(NDI2HD‐T2) polymers with different M_n of 13.6 ( P_L ), 22.9 ( P_M ), and 49.9 kg mol^?1 ( P_H ) are prepared by changing the amount of end‐capping agent (2‐bromothiophene) during polymerization. Increasing the M_n values of P(NDI2HD‐T2) polymers leads to a remarkable shift of dominant lamellar crystallite textures from edge‐on ( P_L ) to face‐on ( P_H ) as well as more than a twofold increase in the crystallinity. For example, the portion of face‐on oriented crystallites is dramatically increased from 21.5% and 46.1%, to 78.6% for P_L , P_M, and P_H polymers. These different packing structures in terms of the molecular orientation greatly affect the charge dissociation efficiency at the donor/acceptor interface and thus the short‐circuit current density of the all‐PSCs. All‐PSCs with PTB7‐Th as electron donor and P_H as electron acceptor show the highest efficiency of 6.14%, outperforming those with P_M (5.08%) and P_L (4.29%).     

Thermally Stable All‐Polymer Solar Cells with High Tolerance on Blend Ratios

Tuning the blend composition is an essential step to optimize the power conversion efficiency (PCE) of organic bulk heterojunction (BHJ) solar cells. PCEs from devices of unoptimized donor:acceptor (D:A) weight ratio are generally significantly lower than optimized devices. Here, two high‐performance organic nonfullerene BHJ blends PBDB‐T:ITIC and PBDB‐T:N2200 are adopted to investigate the effect of blend ratio on device performance. It is found that the PCEs of polymer‐polymer (PBDB‐T:N2200) blend are more tolerant to composition changes, relative to polymer‐molecule (PBDB‐T:ITIC) devices. In both systems, short‐circuit current density (J_sc) is tracked closely with PCE, indicating that exciton dissociation and transport strongly influence PCEs. With dilute acceptor concentrations, polymer‐polymer blends maintain high electron mobility relative to the polymer‐molecule blends, which explains the dramatic difference in PCEs between them as a function of D:A blend ratio. In addition, polymer‐polymer solar cells, especially at high D:A blend ratio, are stable (less than 5% relative loss) over 70 d under continuous heating at 80 °C in a glovebox without encapsulation. This work demonstrates that all‐polymer solar cells show advantage in operational lifetime under thermal stress and blend‐ratio resilience, which indicates their high potential for designing of stable and scalable solar cells.     

Structure Evolution of Oligomer Fused‐Ring Electron Acceptors toward High Efficiency of As‐Cast Polymer Solar Cells

The structure evolution of oligomer fused‐ring electron acceptors (FREAs) toward high efficiency of as‐cast polymer solar cells (PSCs) is reported. First, a series of FREAs (IC‐(1‐3)IDT‐IC) based on indacenodithiophene (IDT) oligomers as cores are designed and synthesized, effects of IDT number (1–3) on their basic optical and electronic properties are investigated, and more importantly, the relationship between device performance of as‐cast PSCs and donor(D)/acceptor(A) matching (absorption, energy level, morphology, and charge transport) of IC‐(1‐3)IDT‐IC acceptors and two representative polymer donors, PTB7‐Th and PDBT‐T1 is surveyed. Then, the most promising D/A system (PDBT‐T1/IC‐1IDT‐IC) with the best D/A harmony among the six D/A combinations, which yields a power conversion efficiency (PCE) of 7.39%, is found. Finally, changing the side‐chains in IC‐1IDT‐IC from alkylphenyl to alkyl enhances the PCE from 7.39% to 9.20%.     

Delicate Morphology Control Triggers 14.7% Efficiency All‐Small‐Molecule Organic Solar Cells

Morphology is a critical factor to determine the photovoltaic performance of organic solar cells (OSCs). However, delicately fine‐tuning the morphology involving only small molecules is an extremely challenging task. Herein, a simple, generic, and effective concentration‐induced morphology manipulation approach is demonstrated to prompt both the state‐of‐the‐art thin‐film BTR‐Cl:Y6 and thick‐film BTR:PC₇₁BM all‐small‐molecule (ASM) OSCs to a record level. The morphology is delicately controlled by subtly altering the prepared solution concentration but maintaining the identical active layer thickness. The remarkable performance enhancement achieved by this approach mainly results from the enhanced absorption, reduced trap‐assistant recombination, increased crystallinity, and optimized phase‐separated network. These findings demonstrate that a concentration‐induced morphology manipulation strategy can further propel the reported best‐performing ASM OSCs to a brand‐new level, and provide a promising way to delicately control the morphology towards high‐performance ASM OSCs.