A Low‐Cost Durable Na‐FeCl2 Battery with Ultrahigh Rate Capability

Na‐based batteries have long been regarded as an inexpensive, sustainable candidate for large‐scale stationary energy storage applications. Unfortunately, the market penetration of conventional Na‐NiCl₂ batteries is approaching its limit for several reasons, including limited rate capability and high Ni cost. Herein, a Na‐FeCl₂ battery operating at 190 °C is reported that allows a capacity output of 116 mAh g^?1 at an extremely high current density of 33.3 mA cm^?2 (≈0.6C). The superior rate performance is rooted in the intrinsically fast kinetics of the Fe/Fe²⁺ redox reaction. Furthermore, it is demonstrated that a small amount of Ni additive (10 mol%) effectively mitigates capacity fading of the Fe/NaCl cathode caused by Fe particle pulverization during long‐term cycling. The modified Fe/Ni cathode exhibits excellent cycling stability, maintaining a discharge energy density of over 295 Wh kg^?1 for 200 cycles at 10 mA cm^?2 (≈C/5).     

Sodium Plating from Na‐β″‐Alumina Ceramics at Room Temperature,Paving the Way for Fast‐Charging All‐Solid‐State Batteries

All‐solid‐state batteries with an alkali metal anode have the potential to achieve high energy density. However, the onset of dendrite formation limits the maximum plating current density across the solid electrolyte and prevents fast charging. It is shown that the maximum plating current density is related to the interfacial resistance between the solid electrolyte and the metal anode. Due to their high ionic conductivity, low electronic conductivity, and stability against sodium metal, Na‐β″‐alumina ceramics are excellent candidates as electrolytes for room‐temperature all‐solid‐state batteries. Here, it is demonstrated that a heat treatment of Na‐β″‐alumina ceramics in argon atmosphere enables an interfacial resistance <10 Ω cm² and current densities up to 12 mA cm^?2 at room temperature. The current density obtained for Na‐β″‐alumina is ten times higher than that measured on a garnet‐type Li₇La₃Zr₂O₁₂ electrolyte under equivalent conditions. X‐ray photoelectron spectroscopy shows that eliminating hydroxyl groups and carbon contaminations at the interface between Na‐β″‐alumina and sodium metal is key to reach such values. By comparing the temperature‐dependent stripping/plating behavior of Na‐β″‐alumina and Li₇La₃Zr₂O₁₂, the role of the alkali metal in governing interface kinetics is discussed. This study provides new insights into dendrite formation and paves the way for fast‐charging all‐solid‐state batteries.     

An Advanced Na–FeCl2 ZEBRA Battery for Stationary Energy Storage Application

Sodium‐metal chloride batteries, ZEBRA, are considered one of the most important electrochemical devices for stationary energy storage applications because of its advantages of good cycle life, safety, and reliability. However, sodium–nickel chloride (Na–NiCl₂) batteries, the most promising redox chemistry in ZEBRA batteries, still face great challenges for the practical application due to its inevitable feature of using Ni cathode (high materials cost). Here, a novel intermediate‐temperature sodium–iron chloride (Na–FeCl₂) battery using a molten sodium anode and Fe cathode is proposed and demonstrated. The first use of unique sulfur‐based additives in Fe cathode enables Na–FeCl₂ batteries can be assembled in the discharged state and operated at intermediate temperature (<200 °C). The results presented demonstrate that intermediate‐temperature Na–FeCl₂ battery technology could be a propitious solution for ZEBRA battery technologies by replacing the traditional Na–NiCl₂ chemistry.     

Fast Sodium Storage in TiO2@CNT@C Nanorods for High‐Performance Na‐Ion Capacitors

Na‐ion capacitors have attracted extensive interest due to the combination of the merits of high energy density of batteries and high power density as well as long cycle life of capacitors. Here, a novel Na‐ion capacitor, utilizing TiO₂@CNT@C nanorods as an intercalation‐type anode and biomass‐derived carbon with high surface area as an ion adsorption cathode in an organic electrolyte, is reported. The advanced architecture of TiO₂@CNT@C nanorods, prepared by electrospinning method, demonstrates excellent cyclic stability and outstanding rate capability in half cells. The contribution of extrinsic pseudocapacitance affects the rate capability to a large extent, which is identified by kinetics analysis. A key finding is that ion/electron transfer dynamics of TiO₂@CNT@C could be effectively enhanced due to the addition of multiwalled carbon nanotubes. Also, the biomass‐derived carbon with high surface area displays high specific capacity and excellent rate capability. Owing to the merits of structures and excellent performances of both anode and cathode materials, the assembled Na‐ion capacitors provide an exceptionally high energy density (81.2 W h kg^?1) and high power density (12 400 W kg^?1) within 1.0–4.0 V. Meanwhile, the Na‐ion capacitors achieve 85.3% capacity retention after 5000 cycles tested at 1 A g^?1.     

Mesoporous MoS2 as a Transition Metal Dichalcogenide Exhibiting Pseudocapacitive Li and Na‐Ion Charge Storage

The ion insertion properties of MoS₂ continue to be of widespread interest for energy storage. While much of the current work on MoS₂ has been focused on the high capacity four‐electron reduction reaction, this process is prone to poor reversibility. Traditional ion intercalation reactions are highlighted and it is demonstrated that ordered mesoporous thin films of MoS₂ can be utilized as a pseudocapacitive energy storage material with a specific capacity of 173 mAh g^?1 for Li‐ions and 118 mAh g^?1 for Na‐ions at 1 mV s^?1. Utilizing synchrotron grazing incidence X‐ray diffraction techniques, fast electrochemical kinetics are correlated with the ordered porous structure and with an iso‐oriented crystal structure. When Li‐ions are utilized, the material can be charged and discharged in 20 seconds while still achieving a specific capacity of 140 mAh g^?1. Moreover, the nanoscale architecture of mesoporous MoS₂ retains this level of lithium capacity for 10 000 cycles. A detailed electrochemical kinetic analysis indicates that energy storage for both ions in MoS₂ is due to a pseudocapacitive mechanism.     

Confining Ultrathin 2D Superlattices in Mesoporous Hollow Spheres Renders Ultrafast and High‐Capacity Na‐Ion Storage

Sodium‐ion batteries have attracted ever‐increasing attention in view of the natural abundance of sodium resources. Sluggish sodiation kinetics, nevertheless, remain a tough challenge, in terms of achieving high rate capability and high energy density. Herein, a sheet‐in‐sphere nanoconfiguration of 2D titania–carbon superlattices vertically aligned inside of mesoporous TiO₂@C hollow nanospheres is constructed. In such a design, the ultrathin 2D superlattices consist of ordered alternating monolayers of titania and carbon, enabling interpenetrating pathways for rapid transport of electrons and Na⁺ ions as well as a 2D heterointerface for Na⁺ storage. Kinetics analysis discloses that the combination of 2D heterointerface and mesoporosity results an intercalation pseudocapacitive charge storage mechanism, which triggers ultrafast sodiation kinetics. In situ transmission electron microscope imaging and in situ synchrotron X‐ray diffraction techniques elucidate that the sheet‐in‐sphere architecture can maintain robust mechanical and crystallographic structural stability, resulting an extraordinary high rate capability, remarkable stable cycling with a low capacity fading ratio of 0.04% per cycle over 500 cycles at 0.2 C, and exceptionally long‐term cyclability up to 20 000 cycles at 50 C. This study offers a method for the realization of a high power density and long‐term cyclability battery by designing of a hierarchical nanoarchitecture.     

Direct Growth of Flower‐Like δ‐MnO2 on Three‐Dimensional Graphene for High‐Performance Rechargeable Li‐O2 Batteries

A challenge still remains to develop high‐performance and cost‐effective air electrode for Li‐O₂ batteries with high capacity, enhanced rate capability and long cycle life (100 times or above) despite recent advances in this field. In this work, a new design of binder‐free air electrode composed of three‐dimensional (3D) graphene (G) and flower‐like δ‐MnO₂ (3D‐G‐MnO₂) has been proposed. In this design, graphene and δ‐MnO₂ grow directly on the skeleton of Ni foam that inherits the interconnected 3D scaffold of Ni foam. Li‐O₂ batteries with 3D‐G‐MnO₂ electrode can yield a high discharge capacity of 3660 mAh g^?1 at 0.083 mA cm^?2. The battery can sustain 132 cycles at a capacity of 492 mAh g^?1 (1000 mAh g_carbon ^?1) with low overpotentials under a high current density of 0.333 mA cm^?2. A high average energy density of 1350 Wh Kg^?1 is maintained over 110 cycles at this high current density. The excellent catalytic activity of 3D‐G‐MnO₂ makes it an attractive air electrode for high‐performance Li‐O₂ batteries.     

Additional Sodium Insertion into Polyanionic Cathodes for Higher‐Energy Na‐Ion Batteries

Na‐ion technology is increasingly studied as a low‐cost solution for grid storage applications. Many positive electrode materials have been reported, mainly among layered oxides and polyanionic compounds. The vanadium oxy/flurophosphate solid solution Na₃V₂(PO₄)₂F_3‐y O_2y (0 ≤ y ≤ 1), in particular, has proven the ability to deliver ≈500 Wh kg^‐1, operating on the V³⁺/V⁴⁺ (y = 0) or V⁴⁺/V⁵⁺ redox couples (y = 1). This paper reports here on a significant increase in specific energy by enabling sodium insertion into Na₃V₂(PO₄)₂FO₂ to reach Na₄V₂(PO₄)₂FO₂ upon discharge. This occurs at ≈1.6 V and increases the theoretical specific energy to 600 Wh kg^?1, rivaling that of several Li‐ion battery cathodes. This improvement is achieved by the judicious modification of the composition either as O for F substitution, or Al for V substitution, both of which disrupt Na‐ion ordering and thereby enable insertion of the 4th Na. This paper furthermore shows from operando X‐Ray Diffraction (XRD) that this energy is obtained in the cycling range Na₄V₂(PO₄)₂FO₂–NaV₂(PO₄)₂FO₂ with a very small overall volume change of 1.7%, which is one of the smallest volume changes for Na‐ion cathodes and which is a crucial requisite for stable long‐term cycling.     

Magnesium methoxide‐induced chemiluminescent decomposition of bicyclic dioxetanes bearing a 2′‐alkoxy‐2‐hydroxy‐1,1′‐binaphthyl‐7‐yl moiety

Bicyclic dioxetanes 2a–c bearing a 2′‐alkoxy‐2‐hydroxy‐1,1′‐binaphthyl‐7‐yl moiety were effectively synthesized and their base‐induced chemiluminescent decomposition was investigated by the use of alkaline metal (Na⁺ and K⁺) or Mg²⁺ alkoxide in MeOH. When 2a–c were treated with tetrabutylammonium fluoride (TBAF) in dimethyl sulfoxide (DMSO) as a reference system, they showed chemiluminescence as a flash of orange light (maximum wavelength λ_max^CL = 573–577 nm) with efficiency Φ^CL = 6–8 × 10^–2. On the other hand, for an alkaline metal (Na⁺ or K⁺) alkoxide/MeOH system, 2a–c decomposed slowly to emit a glow of chemiluminescence, the spectra of which were shifted slightly toward red from the TBAF/DMSO system, and Φ^CL (= 1.4–2.3 × 10^–3) was considerably decreased. In addition, Mg(OMe)₂ was found to play a characteristic role as a base for the chemiluminescent decomposition of 2a–c through coordination to the intermediary oxidoaryl‐substituted dioxetanes 13. Thus, Mg²⁺ increased Φ^CL to more than twice those with Na⁺ or K⁺, while it shifted λ_max^CL considerably toward blue (λ_max^CL = 550–566 nm). Copyright © 2012 John Wiley & Sons, Ltd.     

A High‐Energy NASICON‐Type Cathode Material for Na‐Ion Batteries

Over the last decade, Na‐ion batteries have been extensively studied as low‐cost alternatives to Li‐ion batteries for large‐scale grid storage applications; however, the development of high‐energy positive electrodes remains a major challenge. Materials with a polyanionic framework, such as Na superionic conductor (NASICON)‐structured cathodes with formula Na_xM₂(PO₄)₃, have attracted considerable attention because of their stable 3D crystal structure and high operating potential. Herein, a novel NASICON‐type compound, Na₄MnCr(PO₄)₃, is reported as a promising cathode material for Na‐ion batteries that deliver a high specific capacity of 130 mAh g^?1 during discharge utilizing high‐voltage Mn^2+/3+ (3.5 V), Mn^3+/4+ (4.0 V), and Cr^3+/4+ (4.35 V) transition metal redox. In addition, Na₄MnCr(PO₄)₃ exhibits a high rate capability (97 mAh g^?1 at 5 C) and excellent all‐temperature performance. In situ X‐ray diffraction and synchrotron X‐ray diffraction analyses reveal reversible structural evolution for both charge and discharge.     

High Performance Na–CuCl2 Rechargeable Battery toward Room Temperature ZEBRA‐Type Battery

Despite a recent increase in the attention given to sodium rechargeable battery systems, they should be further advanced in terms of their energy density and reliability to successfully penetrate the rechargeable battery market. Here, a new room temperature ZEBRA‐type Na–CuCl₂ rechargeable battery is demonstrated that employs CuCl₂ cathode material and nonflammable inorganic liquid electrolyte. The cathode delivers a high energy density of ≈580 Wh kg^?1 with superior capacity retention over 1000 cycles as well as a high round‐trip efficiency of ≈97%, which has never been obtained in an organic electrolyte system and high‐temperature ZEBRA‐type battery. These excellent electrochemical performances are mainly attributed to the use of the SO₂‐based inorganic electrolyte, which guarantees a reversible conversion reaction between CuCl₂ and CuCl with NaCl. It is also demonstrated that the proposed battery chemistry can be extended to other copper halide materials including CuBr₂ and CuF₂, which also show highly promising battery performances as cathode materials for the Na–Cu halide battery system.     

Graphene Wrapped FeSe2 Nano‐Microspheres with High Pseudocapacitive Contribution for Enhanced Na‐Ion Storage

Pseudocapacitance is a Faradaic process that involves surface or near surface redox reactions. Increasing the pseudocapacitive contribution is one of the most effective means to improve the rate performance of electrode materials. In this study, graphene oxide is used as a template to in situ synthesize burr globule‐like FeSe₂/graphene hybrid (B‐FeSe₂/G) using a facile one‐step hydrothermal method. Structural characterization demonstrates that graphene layers not only wrap the surfaces of FeSe₂ particles, but also stretch into the interior of these particles, as a result of which the unique nano‐microsphere structure is successfully established. When serving as anode material for Na‐ion batteries, B‐FeSe₂/G hybrid displays high electrochemical performance in the voltage range of 0.5–2.9 V. The B‐FeSe₂/G hybrid has high reversible capacity of 521.6 mAh·g^?1 at 1.0 A g^?1. Meanwhile, after 400 cycles, high discharge capacity of 496.3 mAh g^?1 is obtained at a rate of 2.5 A g^?1, with a high columbic efficiency of 96.6% and less than 1.0% loss of discharge capacity. Even at the ultrahigh rate of 10 A g^?1, a specific capacity of 316.8 mAh g^?1 can be achieved. Kinetic analyses reveal that the excellent performance of the B‐FeSe₂/G hybrid is largely attributed to the high pseudocapacitive contribution induced by the special nano‐micro structure.     

Theaflavin‐3,3´‐digallate increases the antibacterial activity of β‐lactam antibiotics by inhibiting metallo‐β‐lactamase activity

Metallo‐β‐lactamases (MBLs) are some of the best known β‐lactamases produced by common Gram‐positive and Gram‐negative pathogens and are crucial factors in the rise of bacterial resistance against β‐lactam antibiotics. Although many types of β‐lactamase inhibitors have been successfully developed and used in clinical settings, no MBL inhibitors have been identified to date. Nitrocefin, checkerboard and time‐kill assays were used to examine the enzyme behaviour in vitro. Molecular docking calculation, molecular dynamics simulation, calculation of the binding free energy and ligand‐residue interaction decomposition were used for mechanistic research. The behaviour of the enzymes in vivo was investigated by a mouse infection experiment. We showed that theaflavin‐3,3´‐digallate (TFDG), a natural compound lacking antibacterial activities, can inhibit the hydrolysis of MBLs. In the checkerboard and time‐kill assays, we observed a synergistic effect of TFDG with β‐lactam antibiotics against methicillin‐resistant Staphylococcus aureus BAA1717. Molecular dynamics simulations were used to identify the mechanism of the inhibition of MBLs by TFDG, and we observed that the hydrolysis activity of the MBLs was restricted by the binding of TFDG to Gln242 and Ser369. Furthermore, the combination of TFDG with β‐lactam antibiotics showed effective protection in a mouse Staphylococcus aureus pneumonia model. These findings suggest that TFDG can effectively inhibit the hydrolysis activity of MBLs and enhance the antibacterial activity of β‐lactam antibiotics against pathogens in vitro and in vivo.     

Preparative Enantioseparation of β‐Substituted‐2‐Phenylpropionic Acids by Countercurrent Chromatography With Substituted β‐Cyclodextrin as Chiral Selectors

Preparative enantioseparation of four β‐substituted‐2‐phenylpropionic acids was performed by countercurrent chromatography with substituted β‐cyclodextrin as chiral selectors. The two‐phase solvent system was composed of n‐hexane‐ethyl acetate‐0.10 mol L‐1 of phosphate buffer solution at pH 2.67 containing 0.10 mol L^‐1 of hydroxypropyl‐β‐cyclodextrin (HP‐β‐CD) or sulfobutylether‐β‐cyclodextrin (SBE‐β‐CD). The influence factors, including the type of substituted β‐cyclodextrin, composition of organic phase, concentration of chiral selector, pH value of the aqueous phase, and equilibrium temperature were optimized by enantioselective liquid–liquid extraction. Under the optimum separation conditions, 100 mg of 2‐phenylbutyric acid, 100 mg of tropic acid, and 50 mg of 2,3‐diphenylpropionic acid were successfully enantioseparated by high‐speed countercurrent chromatography, and the recovery of the (±)‐enantiomers was in the range of 90–91% for (±)‐2‐phenylbutyric acid, 91–92% for (±)‐tropic acid, 85–87% for (±)‐2,3‐diphenylpropionic acid with purity of over 97%, 96%, and 98%, respectively. The formation of 1:1 stoichiometric inclusion complex of β‐substituted‐2‐phenylpropionic acids with HP‐β‐CD was determined by UV spectrophotometry and the inclusion constants were calculated by a modified Benesi‐Hildebrand equation. The results showed that different enantioselectivities among different racemates were mainly caused by different enantiorecognition between each enantiomer and HP‐β‐CD, while it might be partially caused by different inclusion capacity between racemic solutes and HP‐β‐CD. Chirality 27:795–801, 2015. © 2015 Wiley Periodicals, Inc.     

Superior Lithium Storage Properties of β‐FeOOH

Several crystal forms of FeOOH are recently reported to be highly promising for lithium storage due to their high capacity, low cost, and environmental friendliness. In particular, β‐FeOOH has shown a capacity of ≈1000 mAh g^?1, which is comparable to other promising iron‐based anodes, such as Fe₂O₃ and Fe₃O_4. However, its storage mechanisms are unclear and the potential for further improvement remains unexplored. Here, it is shown that this material can have a very high reversible capacity of ≈1400 mAh g^?1, which is 20%–40% higher than Fe₂O₃ and Fe₃O₄. Such a high capacity is delivered from a series of reactions including intercalation and conversion reactions, formation/deformation of solid‐state electrolyte interface layers and interfacial storage. The mechanisms are studied by a combination of electrochemical and X‐ray absorption near edge spectroscopic approaches. Moreover, very long cycling performance, that is, after even more than 3000 cycles the material still has a significant capacity of more than 800 mAh g^?1, is obtained by a simple electrode design involving introducing a rigid support into porous electrodes. Such long cycling performance is for the first time achieved for high‐capacity materials based on conversion reactions.     

Na‐Ion Intercalation and Charge Storage Mechanism in 2D Vanadium Carbide

2D vanadium carbide MXene containing surface functional groups (denoted as V₂CT_x , where T_x are surface functional groups) is synthesized and studied as anode material for Na‐ion batteries. V₂CT_x anode exhibits reversible charge storage with good cycling stability and high rate capability through electrochemical test. The charge storage mechanism of V₂CT_x material during Na⁺ intercalation/deintercalation and the redox reaction of vanadium are studied using a combination of synchrotron based X‐ray diffraction, hard X‐ray absorption near edge spectroscopy (XANES), and soft X‐ray absorption spectroscopy (sXAS). Experimental evidence of a major contribution of redox reaction of vanadium to the charge storage and the reversible capacity of V₂CT_x during sodiation/desodiation process are provided through V K ‐edge XANES and V L _2,3‐edge sXAS results. A correlation between the CO₃^2? content and the Na⁺ intercalation/deintercalation states in the V₂CT_x electrode observed from C and O K ‐edge in sXAS results implies that some additional charge storage reactions may take place between the Na⁺‐intercalated V₂CT_x and the carbonate‐based nonaqueous electrolyte. The results of this study provide valuable information for the further studies on V₂CT_x as anode material for Na‐ion batteries and capacitors.     

BMP‐2 modulates β‐catenin signaling through stimulation of Lrp5 expression and inhibition of β‐TrCP expression in osteoblasts

Canonical BMP and Wnt signaling pathways play critical roles in regulation of osteoblast function and bone formation. Recent studies demonstrate that BMP‐2 acts synergistically with β‐catenin to promote osteoblast differentiation. To determine the molecular mechanisms of the signaling cross‐talk between canonical BMP and Wnt signaling pathways, we have used primary osteoblasts and osteoblast precursor cell lines 2T3 and MC3T3‐E1 cells to investigate the effect of BMP‐2 on β‐catenin signaling. We found that BMP‐2 stimulates Lrp5 expression and inhibits the expression of β‐TrCP, the F‐box E3 ligase responsible for β‐catenin degradation and subsequently increases β‐catenin protein levels in osteoblasts. In vitro deletion of the β‐catenin gene inhibits osteoblast proliferation and alters osteoblast differentiation and reduces the responsiveness of osteoblasts to the BMP‐2 treatment. These findings suggest that BMP‐2 may regulate osteoblast function in part through modulation of the β‐catenin signaling. J. Cell. Biochem. 108: 896–905, 2009. © 2009 Wiley‐Liss, Inc.     

Evaluation of the double‐disk synergy test for New Delhi metallo‐β‐lactamase‐1 and other metallo‐β‐lactamase producing gram‐negative bacteria by using metal‐ethylenediaminetetraacetic acid complexes

New Delhi metallo‐β‐lactamase‐1 (NDM‐1), one of the metallo‐β‐lactamases (MBLs), has been identified from clinical isolates worldwide. Rapid detection of NDM‐1 producers is necessary to prevent their dissemination. Seven types of EDTA complexes were evaluated as MBL inhibitors in double‐disk synergy tests (DDSTs), resulting in detection of the first isolate of NDM‐1‐producing Escherichia coli (NDM‐1 Dok01) in Japan. NDM‐1 Dok01 was detected when EDTA magnesium disodium salt tetrahydrate (Mg‐EDTA), EDTA calcium disodium salt dihydrate, EDTA cobalt disodium salt tetrahydrate and EDTA copper disodium salt tetrahydrate were used as MBL inhibitors. The sensitivity and specificity of DDSTs using Mg‐EDTA for 75 MBL producers and 25 non‐MBL producers were 96.0% and 100%, respectively. These findings indicate that the DDST method using Mg‐EDTA can detect MBL‐producing strains, including NDM‐1 producers.