Polysulfonated Fluoro‐oxyPBI Membranes for PEMFCs: An Efficient Strategy to Achieve Good Fuel Cell Performances with Low H3PO4 Doping Levels

Polybenzimidazoles (PBIs) are promising materials to replace Nafion as the electrolyte in polymer electrolyte membrane fuel cells (PEMFCs). The challenge with these materials is to achieve a good compromise between the H₃PO₄ doping level and membrane stability. This can be obtained by a proper monomer design, which can lead to better performing membrane electrode assemblies (MEAs), in terms of durability, acid leaching, and electrode safety. Here the easy and inexpensive synthesis of hexafluoropropylidene oxyPBI (F₆‐oxyPBI) and bisulfonated hexafluoropropylidene oxyPBI (F₆‐oxyPBI‐2SO₃H) is reported. The membranes based on F₆‐oxyPBI‐2SO₃H are more stable in an oxidative environment and more mechanically resistant than standard PBI and F₆‐oxyPBI. Whereas the attainable doping levels are low because of fluorine‐induced hydrophobicity, polysulfonation allows high proton conductivity, and fuel cell performances better than those reported for MEAs with F₆PBI‐ or PBI membranes with much higher doping levels. In the case of MEA with a F₆‐oxyPBI‐2SO₃H membrane, a peak power density of 360 mW cm^?2 is measured. Fuel cell performances of 604 mV at 0.2 A cm^?2 are maintained for 800 h without membrane degradation. Low H₂ permeability is measured, which remains almost unaffected during a 1000 h life‐test.     

A Cu‐Based Nanoparticulate Film as Super‐Active and Robust Catalyst Surpasses Pt for Electrochemical H2 Production from Neutral and Weak Acidic Aqueous Solutions

Electrocatalysts that are stable and highly active at low overpotential (η) under mild conditions as well as cost‐effective and scalable are eagerly desired for potential use in photo‐ and electro‐driven hydrogen evolution devices. Here the fabrication and characterization of a super‐active and robust Cu‐Cu_xO‐Pt nanoparticulate electrocatalyst is reported, which displays a small Tafel slope (44 mV dec^?1) and a large exchange current density (1.601 mA cm^?2) in neutral buffer solution. The catalytic current density of this catalyst film reaches 500 mA cm^?2 at η = ?390 ± 12 mV and 20 mA cm^?2 at η = ?45 ± 3 mV, which are significantly higher than the values displayed by Pt foil and Pt/C electrodes in neutral buffer solution and even comparable with the activity of Pt electrode in 0.5 m H₂SO₄ solution.     

Copper–Nickel Nitride Nanosheets as Efficient Bifunctional Catalysts for Hydrazine‐Assisted Electrolytic Hydrogen Production

Electrocatalytic water splitting is one of the sustainable and promising strategies to generate hydrogen fuel but still remains a great challenge because of the sluggish anodic oxygen evolution reaction (OER). A very effective approach to dramatically decrease the input cell voltage of water electrolysis is to replace the anodic OER with hydrazine oxidation reaction (HzOR) due to its lower thermodynamic oxidation potential. Therefore, developing the low‐cost and efficient HzOR catalysts, coupled with the cathodic hydrogen evolution reaction (HER), is tremendously important for energy‐saving electrolytic hydrogen production. Herein, a new‐type of copper–nickel nitride (Cu₁Ni₂‐N) with rich Cu₄N/Ni₃N interface is rationally constructed on carbon fiber cloth. The 3D electrode exhibits extraordinary HER performance with an overpotential of 71.4 mV at 10 mA cm^?2 in 1.0 m KOH, simultaneously delivering an ultralow potential of 0.5 mV at 10 mA cm^?2 for HzOR in a 1.0 m KOH/0.5 m hydrazine electrolyte. Moreover, the electrolytic cell utilizing the synthesized Cu₁Ni₂‐N electrode as both the cathode and anode display a cell voltage of 0.24 V at 10 mA cm^?2 with an excellent stability over 75 h. The present work develops the promising copper–nickel‐based nitride as a bifunctional electrocatalyst through hydrazine‐assistance for energy‐saving electrolytic hydrogen production.     

Multiblock Copolymers with Highly Sulfonated Blocks Containing Di‐ and Tetrasulfonated Arylene Sulfone Segments for Proton Exchange Membrane Fuel Cell Applications

Multiblock copoly(arylene ether sulfone)s with different block lengths and ionic contents are tailored for durable and proton‐conducting electrolyte membranes. Two series of fully aromatic copolymers are prepared by coupling reactions between non‐sulfonated hydrophobic precursor blocks and highly sulfonated hydrophilic precursor blocks containing either fully disulfonated diarylsulfone or fully tetrasulfonated tetraaryldisulfone segments. The sulfonic acid groups are exclusively introduced in ortho positions to the sulfone bridges to impede desulfonation reactions and give the blocks ion exchange capacities (IECs) of 4.1 and 4.6 meq. g^?1, respectively. Solvent cast block copolymer membranes show well‐connected hydrophilic nanophase domains for proton transport and high decomposition temperatures above 310 °C under air. Despite higher IEC values, membranes containing tetrasulfonated tetraaryldisulfone segments display a markedly lower water uptake than the corresponding ones with disulfonated diarylsulfone segments when immersed in water at 100 °C, presumably because of the much higher chain stiffness and glass transition temperature of the former segments. The former membranes have proton conductivities in level of a perfluorosulfonic acid membrane (NRE212) under fully humidified conditions. A membrane with an IEC of 1.83 meq. g^?1 reaches above 6 mS cm^?1 under 30% relative humidity at 80 °C, to be compared with 10 mS cm^?1 for NRE212 under the same conditions.     

Flexible and High‐Loading Lithium–Sulfur Batteries Enabled by Integrated Three‐In‐One Fibrous Membranes

Lithium–sulfur batteries are appealing as high‐energy storage systems and hold great application prospects in wearable and portable electronics. However, severe shuttle effects, low sulfur conductivity, and especially poor electrode mechanical flexibility restrict sulfur utilization and loading for practical applications. Herein, high‐flux, flexible, electrospun fibrous membranes are developed, which succeed in integrating three functional units (cathode, interlayer, and separator) into an efficient composite. This structure helps to eliminate negative interface effects, and effectively drives synergistic boosts to polysulfide confinement, electron transfer, and lithium‐ion diffusion. It delivers a high initial capacity of 1501 mA h g^?1 and a discharge capacity of 933 mA h g^?1 after 400 cycles, with slow capacity attenuation (0.069% per cycle). Even under high sulfur loading (13.2 mg cm^?2, electrolyte/sulfur ratio = 6 mL g^?1) or in an alternative folded state, this three‐in‐one membrane still exhibits high areal capacity (11.4 mA h cm^?2) and exceptional application performance (powering an array of over 30 light‐emitting diodes (LEDs)), highlighting its huge potential in high‐energy flexible devices.     

Miniaturized Supercapacitors: Focused Ion Beam Reduced Graphene Oxide Supercapacitors with Enhanced Performance Metrics

Miniaturization of energy storage devices with enhanced performance metrics can reduce the footprint of microdevices being used in our daily life. Micro‐­supercapacitor architectures with planar geometry provides several advantages, such as, the ability to control and reduce the distances ions travel between two electrodes, easy integration to microdevices, and offer the potential of being extended into 3D without compromising the interelectrode distances. Here, focused ion beam (FIB) technology is used to directly write miniaturized planar electrode systems of reduced graphene oxide (FIB‐rGO) on films of graphene oxide. Using optimized ion beam irradiation, interdigitated FIB‐rGO electrode designs with 40 μm long and 3.5 μm wide fingers with ultrasmall interelectrode spacing of 1 μm demonstrate a large capacitance (102 mF cm^?2), ultrasmall time response (0.03 ms), low equivalent series resistance (0.35 mΩ cm²), and retain 95% of the capacitance after 1000 cycles at an ultrahigh current density of 45 mA cm^?2. These performance metrics show remarkable improvements on several counts of supercapacitor performance over existing reports due to the miniaturized electrode dimensions and minimal damage to the graphene sheets. It is believed that these results can provide avenues for large‐scale fabrication of arrayed, planar, high‐performance micro‐supercapacitors with a small environmental footprint.     

A Stable Graphitic,Nanocarbon‐Encapsulated,Cobalt‐Rich Core–Shell Electrocatalyst as an Oxygen Electrode in a Water Electrolyzer

The oxygen electrode plays a vital role in the successful commercialization of renewable energy technologies, such as fuel cells and water electrolyzers. In this study, the Prussian blue analogue‐derived nitrogen‐doped nanocarbon (NC) layer‐trapped, cobalt‐rich, core–shell nanostructured electrocatalysts (core–shell Co@NC) are reported. The electrode exhibits an improved oxygen evolution activity and stability compared to that of the commercial noble electrodes. The core–shell Co@NC‐loaded nickel foam exhibits a lower overpotential of 330 mV than that of IrO₂ on nickel foam at 10 mA cm^?2 and has a durability of over 400 h. The commercial Pt/C cathode‐assisted, core–shell Co@NC–anode water electrolyzer delivers 10 mA cm^?2 at a cell voltage of 1.59 V, which is 70 mV lower than that of the IrO₂–anode water electrolyzer. Over the long‐term chronopotentiometry durability testing, the IrO₂–anode water electrolyzer shows a cell voltage loss of 230 mV (14%) at 95 h, but the loss of the core–shell Co@NC–anode electrolyzer is only 60 mV (4%) even after 350 h cell‐operation. The findings indicate that the Prussian blue analogue is a class of inorganic nanoporous materials that can be used to derive metal‐rich, core–shell electrocatalysts with enriched active centers.     

Fast‐Charging and Ultrahigh‐Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm^?2) and small areal capacity (<5 mAh cm^?2), which essentially limits their high‐power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low‐cost Si wafers are used and are chemically etched down to 20–30 µm membranes. Simply laminating a Si membrane onto Li foil results in the formation of Li_xSi alloy film fused onto Li metal with mechanical robustness and high Li‐ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm^?2 and unprecedented areal capacity up to 100 mAh cm^?2. Furthermore, the surface alloyed Li anode is paired with amorphous MoS₃ cathode and achieves remarkable full‐cell performance.     

Bifunctional Conducting Polymer Coated CoP Core–Shell Nanowires on Carbon Paper as a Free‐Standing Anode for Sodium Ion Batteries

This study proposes a conformal surface coating of conducting polymer for protecting 1D nanostructured electrode material, thereby enabling a free‐standing electrode without binder for sodium ion batteries. Here, polypyrrole (PPy), which is one of the representative conducting polymers, encapsulated cobalt phosphide (CoP) nanowires (NWs) grown on carbon paper (CP), finally realizes 1D core–shell CoP@PPy NWs/CP. The CoP core is connected to the PPy shell via strong chemical bonding, which can maintain a Co–PPy framework during charge/discharge. It also possesses bifunctional features that enhances the charge transfer and buffers the volume expansion. Consequently, 1D core–shell CoP@PPy NWs/CP demonstrates superb electrochemical performance, delivering a high areal capacity of 0.521 mA h cm^?2 at 0.15 mA cm^?2 after 100 cycles, and 0.443 mA h cm^?2 at 1.5 mA cm^?2 even after 1000 cycles. Even at a high current density of 3 mA cm^?2, a significant areal discharge capacity reaching 0.285 mA h cm^?2 is still maintained. The outstanding performance of the CoP@PPy NWs/CP free‐standing anode provides not only a novel insight into the modulated volume expansion of anode materials but also one of the most effective strategies for binder‐free and free‐standing electrodes with decent mechanical endurance for future secondary batteries.     

Densification by Compaction as an Effective Low‐Cost Method to Attain a High Areal Lithium Storage Capacity in a CNT@Co3O4 Sponge

Achieving a high areal capacity is essential for the transfer of outstanding laboratory electrode results to commercial applications and also to ensure there exists a capacity matched cathode and anode for a properly tuned battery. Despite intensive efforts, most electrode materials exhibit areal capacities lower than that of the graphite anodes (4 mA h cm^?2). An effective and low‐cost approach is reported to attain a high areal capacity via an intense densification by compacting a porous carbon nanotube sponge grafted with Co₃O₄ nanoparticles. The hybrid sponge can be compacted to a large degree (up to a tenfold densification) while still keeping its structural integrity and the 3D porous network. This method allows achieving a mass loading of up ?to 14.3 mg cm^?2 and an areal capacity of 12 mA h cm^?2 (at a current density of 200 mA g^?1) together with a gravimetric capacity of >800 mA h g^?1. This densification by compaction approach offers an effective and low‐cost strategy to develop high mass loading and areal capacity electrodes for practical energy storage systems.     

Hierarchical Zn–Co–S Nanowires as Advanced Electrodes for All Solid State Asymmetric Supercapacitors

A facile two‐step strategy is developed to design the large‐scale synthesis of hierarchical, unique porous architecture of ternary metal hydroxide nanowires grown on porous 3D Ni foam and subsequent effective sulfurization. The hierarchical Zn–Co–S nanowires (NWs) arrays are directly employed as an electrode for supercapacitors application. The as‐synthesized Zn–Co–S NWs deliver an ultrahigh areal capacity of 0.9 mA h cm^?2 (specific capacity of 366.7 mA h g^?1) at a current density of 3 mA cm^?2, with an exceptional rate capability (≈227.6 mA h g^?1 at a very high current density of 40 mA cm^?2) and outstanding cycling stability (≈93.2% of capacity retention after 10 000 cycles). Most significantly, the assembled Zn–Co–S NWs//Fe₂O₃@reduced graphene oxide asymmetric supercapacitors with a wide operating potential window of ≈1.6 V yield an ultrahigh volumetric capacity of ≈1.98 mA h cm^?3 at a current density of 3 mA cm^?2, excellent energy density of ≈81.6 W h kg^?1 at a power density of ≈559.2 W kg^?1, and exceptional cycling performance (≈92.1% of capacity retention after 10 000 cycles). This general strategy provides an alternative to design the other ternary metal sulfides, making it facile, free‐standing, binder‐free, and cost‐effective ternary metal sulfide‐based electrodes for large‐scale applications in modern electronics.     

Hydrothermal Synthesis of Monolithic Co3Se4 Nanowire Electrodes for Oxygen Evolution and Overall Water Splitting with High Efficiency and Extraordinary Catalytic Stability

Cobalt selenide has been proposed to be an effective low‐cost electrocatalyst toward the oxygen evolution reaction (OER) due to its well‐suited electronic configuration. However, pure cobalt selenide has by far still exhibited catalytic activity far below what is expected. Herein, this paper for the first time reports the synthesis of new monoclinic Co₃Se₄ thin nanowires on cobalt foam (CF) via a facile one‐pot hydrothermal process using selenourea. When used to catalyze the OER in basic solution, the conditioned monolithic self‐supported Co₃Se₄/CF electrode shows an exceptionally high catalytic current of 397 mA cm^?2 at a low overpotential (η) of 320 mV, a small Tafel slope of 44 mV dec^?1, a turnover frequency of 6.44 × 10^?2 s^?1 at η = 320 mV, and excellent electrocatalytic stability at various current densities. Furthermore, an electrolyzer is assembled using two symmetrical Co₃Se₄/CF electrodes as anode and cathode, which can deliver 10 and 20 mA cm^?2 at low cell voltages of 1.59 and 1.63 V, respectively. More significantly, the electrolyzer can operate at 10 mA cm^?2 over 3500 h and at 100 mA cm^?2 for at least 2000 h without noticeable degradation, showing extraordinary operational stability.     

Electroless Plating of Highly Efficient Bifunctional Boride‐Based Electrodes toward Practical Overall Water Splitting

Exploring highly‐efficient and low‐cost electrodes for both hydrogen and oxygen evolution reaction (HER and OER) is of primary importance to economical water splitting. Herein, a series of novel and robust bifunctional boride‐based electrodes are successfully fabricated using a versatile Et₂NHBH₃‐involved electroless plating (EP) approach via deposition of nonprecious boride‐based catalysts on various substrates. Owing to the unique binder‐free porous nodule structure induced by the hydrogen release EP reaction, most of the nonprecious boride‐based electrodes are highly efficient for overall water splitting. As a distinctive example, the Co‐B/Ni electrode can afford 10 mA cm^?2 at overpotentials of only 70 mV for HER and 140 mV for OER, and can also survive at large current density of 1000 mA cm^?2 for over 20 h without performance degradation in 1.0 m KOH. Several boride‐based two‐electrode electrolyzers can achieve 10 mA cm^?2 at low voltages of around 1.4 V. Moreover, the facile EP approach is economically viable for flexible and large size electrode production.     

High‐Performance and Breathable Polypyrrole Coated Air‐Laid Paper for Flexible All‐Solid‐State Supercapacitors

High‐performance, breathable, conductive, and flexible polypyrrole (PPy) coated paper electrodes are prepared by an interfacial polymerization method using air‐laid paper as a substrate. Owing to the synergistic effect of superior electrical conductivity, high wettability, and the porous architecture, the prepared electrode not only shows an outstanding specific capacitance and rate abilities (3100 and 2579 mF cm^?2 at 1 and 20 mA cm^?2 for a PPy coated paper electrode), but also exhibits excellent flexibility, wearability, and breathability. Based on these superior features, an all‐solid‐state supercapacitor assembled with the PPy coated paper electrodes shows an outstanding energy density of 62.4 µW h cm^?2, remarkable air permeability and excellent flexibility to sustain various deformations. Furthermore, large‐scale fabrication of conductive flexible paper electrode can be easily achieved through this method. Therefore, this work offers a new vision for flexible energy storage.     

A High‐Performance Composite Electrode for Vanadium Redox Flow Batteries

A composite electrode composed of reduced graphene oxide‐graphite felt (rGO‐GF) with excellent electrocatalytic redox reversibility toward V²⁺/V³⁺ and VO²⁺/VO₂⁺ redox couples in vanadium batteries was fabricated by a facile hydrothermal method. Compared with the pristine graphite felt (GF) electrode, the rGO‐GF composite electrode possesses abundant oxygen functional groups, high electron conductivity, and outstanding stability. Its corresponding energy efficiency and discharge capacity are significantly increased by 20% and 300%, respectively, at a high current density of 150 mA cm^?2. Moreover, a discharge capacity of 20 A h L^?1 is obtained with a higher voltage efficiency (74.5%) and energy efficiency (72.0%), even at a large current density of 200 mA cm^?2. The prepared rGO‐GF composite electrode holds great promise as a high‐performance electrode for vanadium redox flow battery (VRFB).     

Direct Growth of Flower‐Like δ‐MnO2 on Three‐Dimensional Graphene for High‐Performance Rechargeable Li‐O2 Batteries

A challenge still remains to develop high‐performance and cost‐effective air electrode for Li‐O₂ batteries with high capacity, enhanced rate capability and long cycle life (100 times or above) despite recent advances in this field. In this work, a new design of binder‐free air electrode composed of three‐dimensional (3D) graphene (G) and flower‐like δ‐MnO₂ (3D‐G‐MnO₂) has been proposed. In this design, graphene and δ‐MnO₂ grow directly on the skeleton of Ni foam that inherits the interconnected 3D scaffold of Ni foam. Li‐O₂ batteries with 3D‐G‐MnO₂ electrode can yield a high discharge capacity of 3660 mAh g^?1 at 0.083 mA cm^?2. The battery can sustain 132 cycles at a capacity of 492 mAh g^?1 (1000 mAh g_carbon ^?1) with low overpotentials under a high current density of 0.333 mA cm^?2. A high average energy density of 1350 Wh Kg^?1 is maintained over 110 cycles at this high current density. The excellent catalytic activity of 3D‐G‐MnO₂ makes it an attractive air electrode for high‐performance Li‐O₂ batteries.     

Membrane potential of the unfertilized sea urchin egg

The membrane potential, specific resistance, and potassium selectivity of the unfertilized Strongylocentrotus purpuratus egg were determined by two independent methods: tracer flux and microelectrode. The potassium influx was 0.50 ± 0.2 pmole/cm²· sec, which was greater than the sodium, chloride, and calcium influxes by factors of 4, 7, and 75, respectively. By means of the constant-field equations, the flux data were used to calculate membrane potential (?70 mV) and specific resistance (420 kΩ · cm²). The effect of the external potassium concentration on the sodium influx was determined and the results closely fit the result expected if the membrane behaved as a potassium electrode. Microelectrode measurements of the potential and resistance were ?75 ± 3 mV and 380 ± kΩ · cm².     

Scalable Triple Cation Mixed Halide Perovskite–BiVO4 Tandems for Bias‐Free Water Splitting

Strong interest exists in the development of organic–inorganic lead halide perovskite photovoltaics and of photoelectrochemical (PEC) tandem absorber systems for solar fuel production. However, their scalability and durability have long been limiting factors. In this work, it is revealed how both fields can be seamlessly merged together, to obtain scalable, bias‐free solar water splitting tandem devices. For this purpose, state‐of‐the‐art cesium formamidinium methylammonium (CsFAMA) triple cation mixed halide perovskite photovoltaic cells with a nickel oxide (NiO_x) hole transport layer are employed to produce Field's metal‐epoxy encapsulated photocathodes. Their stability (up to 7 h), photocurrent density (–12.1 ± 0.3 mA cm^?2 at 0 V versus reversible hydrogen electrode, RHE), and reproducibility enable a matching combination with robust BiVO₄ photoanodes, resulting in 0.25 cm² PEC tandems with an excellent stability of up to 20 h and a bias‐free solar‐to‐hydrogen efficiency of 0.35 ± 0.14%. The high reliability of the fabrication procedures allows scaling of the devices up to 10 cm², with a slight decrease in bias‐free photocurrent density from 0.39 ± 0.15 to 0.23 ± 0.10 mA cm^?2 due to an increasing series resistance. To characterize these devices, a versatile 3D‐printed PEC cell is also developed.     

In Situ Grown Bimetallic MOF‐Based Composite as Highly Efficient Bifunctional Electrocatalyst for Overall Water Splitting with Ultrastability at High Current Densities

A newly designed water‐stable NH₂‐MIL‐88B(Fe₂Ni)‐metal–organic framework (MOF), in situ grown on the surface of a highly conducting 3D macroporous nickel foam (NF), termed NFN‐MOF/NF, is demonstrated to be a highly efficient bifunctional electrocatalyst for overall water splitting with ultrastability at high current densities. The NFN‐MOF/NF achieves ultralow overpotentials of 240 and 87 mV at current density of 10 mA cm^?2 for the oxygen evolution reaction and hydrogen evolution reaction, respectively, in 1 m KOH. For the overall water splitting, it requires only an ultralow cell voltage of 1.56 V to reach the current density of 10 mA cm^?2, outperforming the pairing of Pt/C on NF as the cathode and IrO₂ on NF as the anode at the same catalyst loading. The stability of the NFN‐MOF/NF catalyst is also outstanding, exhibiting only a minor chronopotentiometric decay of 7.8% at 500 mA cm^?2 after 30 h. The success of the present NFN‐MOF/NF catalyst is attributed to the abundant active centers, the bimetallic clusters {Fe₂Ni(µ₃‐O)(COO)₆(H₂O)₃}, in the MOF, the positive coupling effect between Ni and Fe metal ions in the MOF, and synergistic effect between the MOF and NF.     

Membranes with Well‐Defined Selective Layer Regulated by Controlled Solvent Diffusion for High Power Density Flow Battery

Membranes with precise control of selective layer are designed and prepared by adjusting diffusion of solvents. Combining experiments and theoretical calculations, the formation mechanism of ion conductive membranes prepared by a non‐solvent induced phase separation (NIPS) method is found to be related to internal diffusion flux of solvent to the non‐solvent bath and external diffusion flux of non‐solvent to the casting solution. By regulating the internal and external diffusion rates via a two‐step NIPS method, a series of polybenzimidazole (PBI) porous membranes with independently controlled thin selective skin layers and highly porous support layers are fabricated, which achieve a simultaneous improvement in ion selectivity and proton conductivity. A vanadium flow battery assembled with a PBI membrane demonstrates an energy efficiency of 80% at a current density of 220 mA cm^?2, which is the highest value among the reported PBI membranes. This provides a simple and effective way to fabricate membranes with well‐defined morphologies.